Search Documents

By M. A. Trevits, J. E. Urosek, A. C. Smith, M. P. Valoski

Unlike other types of mining accidents, where an incident generally involves only a few workers, the danger of a mine fire extends to every person working in the underground environment. Mine fires can trap or kill those working underground by blocking avenues of escape and rapidly creating heat, asphyxiating gases and toxic fire products that can quickly spread throughout the mine. The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate and improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Because wood is the second most abundant fuel available during a coal mine fire, it was decided that a series of large-scale wood crib fire tests was needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.1

By H. Tudeshki, A. Tayebi

"The large extent of global production and consumption of aggregates from quarries, grabs one´s attention and makes its substantial and essential standpoint in the world today pretty clear. A great amount of aggregates is utilized in civil engineering applications such as road construction, railway industry, concrete production, etc. Considering this fact that igneous rocks display a higher strength and abrasion resistance, this type of rock is preferred in the field of civil engineering. For all these applications, rock quality assurance is a key factor and certainly unavoidable, and it has great influence on the quality of constructions in civil engineering. One of the major problems encountered by both the producers and users of igneous rock is the fact that, with the passage of time, some specific rocks lose their strength, up to a complete loss of structure or in other words, their disintegration and degradation. In the last decades, different methods and procedures such as Glycol test, methylene blue dye test, as well as the Los Angeles test have been introduced to distinguish these rock properties, and to identify these problems. However, as these methods are time consuming, hard to perform, only to be applied to hand-piece samples, requiring special laboratory equipments, and only possible to be accomplished under laboratory conditions, their application has always been limited to some specific cases, and they are neither recommendable nor advantageous. In addition, these methods provide partially different results for the same rock. To address this widespread quality management problem of the quarry industry, a relatively quick, easy and user-friendly approach is necessary. It calls for a systematic solution with a device that can simply be used day to day in a mine for quality control of the quarry´s daily production. This scientific research is concentrated on developing a systematic method for early recognition and diagnosis of rock quality, in order to control and manage the quality of the quarry production in advance. This method was developed, based on the procedure of the magnetic susceptibility measurement. The obtained values can lead to valuable information regarding the quality of the rock and allows the quality control process to be accomplished and performed at the borehole location. This approach has been assessed through extensive field and laboratory studies. A detailed and comprehensive discussion will be made on the results of the experiments. The advantages and impacts of the application of this method, on increasing the reserves and environmental protection are also discussed."

Jan 1, 2011

By T DePetris, B B. Beamish

There has been a gradual increase in the volume of internationally traded thermal and coking coal, with emphasis on blending of coals rather than single coal usage. New Zealand can take advantage of this situation, especially with its low ash and sulphur content coals. However, there is a need to clarify the thermal and coking behaviour of these coals as they relate to other market players, to benefit both the consumer and supplier. The high volatile matter contents of New Zealand coking coals are due to their high vitrinite content, which causes them to demonstrate stronger coking properties over a wider rank range than Gondwana coals. These same high vitrinite levels appear to correspond with lower initial softening temperatures than for Gondwana coals of similar rank. Preliminary results using thermogravimetric analysis also suggest that New Zealand high volatile bituminous coals can be used to substitute for higher rank Gondwana coals in combustion processes.

Jan 1, 1994

On the basis of field observation, four principal styles of hydraulic breccia are recognised, and their characteristic features noted. In practice, hybrid styles are most commonly encountered. Numerous examples will be illustrated during the oral presentation, and the potential for definition of a formative environment is emphasised. In one example presented, it is suggested that more than 50 episodes of hydraulic fracturing can be recognised. In all cases at least sane useful conclusions can be drawn in the context of modeling for drill targets.

Jan 1, 1987

Electro-Flotation Research on Fine Cassiterite

Sep 13, 2010

By James R. Kerr

This study reviews the sulfur and suliuric acid industries in Eastern United States with emphasis on patterns of consumption and marketing. Output of sulfur in the East is relatively small, and most of the area's sulfur requirements are met by gulf coast Frasch sulfur. Over the long ten recovered elemental sulfur from sour natural gas and petroleum may become the East's major source of sulfur. In 1958 sulfuric acid manufacture consumed over 80 percent of the area's sulfur requirements. The leading uses for sulfuric acid were the manufacture of superphosphates and chemicals. Over the years, unit requirements for sulfur and acid in many major markets have been reduced through improved technology, but new markets always have been developed to keep the industry vital and growing.

Jan 1, 1965

By James R. Kerr

This study reviews the sulfur and suliuric acid industries in Eastern United States with emphasis on patterns of consumption and marketing. Output of sulfur in the East is relatively small, and most of the area's sulfur requirements are met by gulf coast Frasch sulfur. Over the long ten recovered elemental sulfur from sour natural gas and petroleum may become the East's major source of sulfur. In 1958 sulfuric acid manufacture consumed over 80 percent of the area's sulfur requirements. The leading uses for sulfuric acid were the manufacture of superphosphates and chemicals. Over the years, unit requirements for sulfur and acid in many major markets have been reduced through improved technology, but new markets always have been developed to keep the industry vital and growing.

Jan 1, 1965

By Etienne Audibert

No satisfactory theory has yet been advanced to explain what takes place when an explosive is fired in a mixture of firedamp and air. The only means of measuring the' danger is to fire the explosive into the gas mixture and note the effect, but the conditions of firing must be chosen carefully. This report is presented in the hope that it will assist in determining what method to use. The experiments have been designed to show the effect of the principal factors involved in the conditions of firing, and the results give information that seems to have some value.

Jan 1, 1940

By Etienne Audibert

No satisfactory theory has yet been advanced to explain what takes place when an explosive is fired in a mixture of firedamp and air. The only means of measuring the danger is to fire the explosive into the gas mixture and note the effect, but the conditions of firing must be chosen carefully. This report is presented in the hope that it will assist in determining what method to use. The experiments have been designed to show the effect of the principal factors involved in the conditions of firing, and the results give information that seems to have some value.

Jan 1, 1940

By Alcides Eloy Cano

Los recursos minerales de un depósito está en función de las dimensiones de la geometría del cuerpo mineral, así como sus reservas minables permiten saber el verdadero valor económico de su contenido. En este sentido, la Geotecnia es una herramienta que define las condiciones de los esfuerzos in situ, predice el comportamiento alrededor de excavaciones subterráneas e interactúa con las labores próximas, así como también la distribución de esfuerzos. Por ello, el presente trabajo señala la aplicación de esta herramienta a una mina subterránea de Oro localizada en el Perú, donde se tiene bloques de mineral económicos, así como señala su accesibilidad con leyes encima del Cut-Off. De forma que se recupera el mineral económico a través de las rutas críticas de carguío, en función de la viabilidad de autosostenimiento.

Sep 12, 2011

By T Sylow, A Correa De Araujo, M Gotelip Barbosa

ArcelorMittal is among the largest world’s producers of iron ore. With a geographically diversified portfolio of iron ore and coal assets, it is strategically positioned to serve the network of steel plants, as well as supply the external global market. ArcelorMittal Mining has a global portfolio of 14 iron ore operating units across Brazil, Bosnia, Canada, Kazakhstan, Liberia, Mexico, Ukraine and the United States. Iron ore products include concentrate for sintering and pelletising, pellets, directly shipped fines and lump ore. This paper presents an overview of ArcelorMittal iron ore mines including iron ore typologies and the annual production of each unit. It will also briefly discuss the processing required in order to obtain marketable products.CITATION:Gotelip Barbosa, M, Correa De Araujo, A and Sylow, T, 2017. Overview of ArcelorMittal mining operations and research and development, in Proceedings Iron Ore 2017, pp 161–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By M. K. Mohanty

Over the years, screen bowl centrifuges have been widely used for dewatering fine coal in coal preparation plants in the United States and elsewhere. Its popularity is attributed to its relatively low cost, its high capacity of providing low moisture content product and its relative ease of operation and maintenance. It is generally recognized in the engineering and scientific communities that screen bowl centrifuges provide some degree of particle size separation while dewatering fine coal in a common application. However, the extent of differential partitioning of coarse and fine particles achievable by a screen bowl centrifuge has not been systematically studied in the past. The present investigation was aimed at conducting a parametric study using a statistically designed experimental program to better understand and optimize the size classification performance of a screen bowl centrifuge. A continuously operating screen bowl centrifuge having a bowl diameter of 0.5 m was used for this study at the Illinois Coal Development Park. Three key operating parameters, i.e., feed flow rate, feed solid content and pool depth, were varied to conduct a total of 17 experiments using a three-level factorial test matrix. Some of the best size separation performances achieved in this study may be described as having an imperfection value of 0.13 at an effective separation size (d50c) of 38 µm and an imperfection value of 0.27 at an effective separation size (d50c) of 2.8 µm. Due to an effective separation of ultrafine high ash materials, the ash content of the screen bowl feed was reduced from 22.3% to a minimum of 8.84% with a combustible recovery of 84.1% and an ash rejection of 71.6%. A higher combustible recovery of 92.1% was achieved at a product ash content of 12.5% with a d50c of 2.8 µm and imperfection of 0.27.

Jan 1, 2008

By A Hekmat, M Fuentes, F Armijo, R Castro, F Rodriguez

Interpreting the behaviour of granular material and simulating the gravity flow are complex processes in cave mining methods. In this paper, a new Cellular Automata based code – FlowSim – is used as a flexible tool to simulate the gravity flow and subsidence zone in block caving mines. The simulation results of the gravity flow model in a real scaled mine as well as a scaled physical model are presented in this study. In this research, FlowSim was first calibrated at a mine, based on the information obtained from smart markers. These markers were located in five points of the second block of the Esmeralda sector, at the El Teniente copper mine, Codelco, Chile. The calibration was performed with the objective of reducing the discrepancy between the extraction zone defined by markers in the mine and FlowSim outputs. Regarding the mine data, FlowSim was calibrated with the minimum error of ten per cent between real and simulated results. Then, the calibrated FlowSim model was used to simulate the flow behaviour of a scaled physical model. This model was constructed in the Block Caving Laboratory of the University of Chile to scale down the same block of the Esmeralda sector with the scale of 1:200. The FlowSim outputs show that this software enables the simulation of the gravity flow of the scaled model with less than five per cent discrepancy in grade and dilution entry to the drawpoints. According to the obtained results, this paper recommends FlowSim as an appropriate tool which can improve the design of production level in block caving and can enhance the prediction of the subsidence zone and dilution entry.CITATION:Castro, R, Hekmat, A, Fuentes, M, Armijo, F and Rodriguez, F, 2016. FlowSim – a versatile flow simulation tool to quantify extraction and design alternatives for block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 645–652 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By D M. Hunter, S M. Iveson, K P. Galvin

For low density materials such as coal, density-based fractionation of particles via the sink-float method is relatively simple due to the availability of liquids of suitable density; however, for high density minerals, suitable heavy liquids are less available and those that are available are expensive and pose significant hazards. At best, sink-float separation can be performed up to densities of 4400 kg/m3 with the use of Clerici’s solution at elevated temperatures. Hence the direct measurement of grade-recovery and density-partition curves is problematic. Therefore, in most cases, beneficiation plants must rely on methods such as QEMSCAN, density tracer particles or very limited information to guide them in the design and optimisation of their plants.This paper describes a density-fractionation method utilising laminar flow through a system of parallel inclined channels to generate a series of overflow fractions at different flow velocities. Here the particles are subject to precise hydrodynamic forces with minimal dispersion or mixing. The size distribution of each overflow fraction at a given flow velocity is obtained using a laser particle size analyser, and combined with a laminar flow model to deduce the corresponding density distribution. The paper describes the application of the method to measure the separation achieved using a REFLUX Classifier to obtain the corresponding feed, product and reject ‘washability curves’, and in turn the full partition surface. Approaches used to corroborate the findings are discussed.CITATION:Hunter, D M, Iveson, S M and Galvin, K P, 2017. A batch elutriation technique for the density-based fractionation of iron ore, in Proceedings Iron Ore 2017, pp 195–104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By P C. Couper, P C. Keall, S J. Mathews, A Francis

An epithermal gold-silver deposit is presently being developed at the Golden Cross Mine in the Waitekauri Valley, 8 km northwest of Waihi, New Zealand. Highest grade mineralisation underground is mainly confined to an elongate zone of strongly banded quartz veining on the hangingwall. Footwall veining is irregular, flatter lying, and of lower grade. Hydrothermal breccias in the ore zone may have economic grades where clasts of vein quartz are present. Jigsaw breccias, shingle breccias, and layered breccias with sedimentary type structures such as layering, crossbedding, and graded bedding have been identified proximal to, and within, quartz veins. Mineralisation in the open pit occurs in and adjacent to stockwork quartz veining.   Three alteration zones are recognised: a central silicic zone enclosing Au-Ag bearing quartz veins, an argillic zone above the stockwork zone and in the footwall of the underground ore zone, and a propylitic zone which is gradational with argillic zone. Intense shearing is confined to the less competent argillic zone.   Precious metal mineralogy consists of electrum (65% Au; 35% Ag) and argentiferous tetrahedrite, polybasite, pyrargyrite, argentite, and native silver. Pyrite is the dominant sulphide mineral. Marcasite, arsenopyrite, and rare chalcopyrite and sphalerite also occur. Oxidation ranges from a few metres in the argillic western stockwork zone to 100 m in fractured rock in the footwall of the stockwork.   The open pit contains a proved and probable reserve of 2.1 million tonne grading 3.5 g/t Au and 17 g/t Ag. The underground mine will produce 2.7 million tonne grading 7.8g/t Au and 27g/t Ag.

Jan 1, 1991

DynoMiner APS Delivery Systems Overview ? New Design of DynoMiner APS-M2 ? Stand alone or attach to Cargo type 10,000 lb (4536 kg) emulsion bins. ? Hose reel w/200-ft (61-m) by 1-inch I.D (25-mm) hose capacity, power rewind. ? Increased water and trace capacity. ? Hose reel and gassing offered as options. ? New Flow Meter ? DN-100: aluminum body, UHMWPE rotors. ? Will be offered as an option. ? APS Nomenclature ? Proposed changes ? DynoMiner APS and APS-M1 to become DynoMiner APS Drifter ? DynoMiner APS-M2 to become DynoMiner APS Stoper. ? Both to have optional gassing / flow metering.

May 1, 2004

By Tim O’Neil

Tire companies have historically used the mining industry as a platform to launch new technologies. And the mining industry has been receptive to that. So, while developing its Two Piece Assembly, Goodyear noted a number of trends in the mining industry: •The global market sophistication of equipment and operations requires the packaging of products and services to provide the best return on investment. •Industry consolidation and growth have resulted in fewer, more powerful mining houses, leveraging purchasing power in the marketplace. •User productivity demands continue to drive original equipment manufacturers to develop higher pay-load equipment. •Technology needs include improved ergonomics, to reduce fatigue and increase operator productivity. •Increased laws and environmental regulation prohibit on-site whole tire disposal practices.

Jan 1, 2003

THE following notes were accumulated during the years 1905 to 1911, when the writer was employed at Stannary Hills. The writer's duty took him over the underground workings daily. In odd moments the geology of the surrounding country was worked out. As the time for this purpose was limited, many interesting points had to be left, untouched. The faulting system in the mines was of such a puzzling character that it seemed as if the geology of the surrounding district might throw some light on it. Dr Jack, in 1907, reported on these mines for the shareholders, but came to no definite conclusions. Unfortunately, the writer has not had access to this report for many years. At the time of his visit the larger develbpments in the Ivanhoe and, Kitchenen orebodies (see Fig 1, B2) were only being opened up. Mr. H. Herman mentions Stannary Hills on p 320, Proceedings Aust Inst ME, new series, No 14, and on p 326 expresses the opinion that the pipe or joint-veins (as at Irvine bank and Stannary Hills) were more valuable to follow than lodes in the granite in that district.GEOLOGY OF DISTRICTThe main feature of the area mapped is a band of altered sedimentary rocks which carry no fossils. It is a mile wide, and consists of a hard band of greywackes 200 ·t ·300 yds. wide, flanked on both sides by contorted shales which become more micaceous as the granite-area to the east is approached. The strata have a general strike of N. 30° W., with a steep westerly dip. A large area of acid intrusive rocks occurs to the west of this band. The outstanding feature of the district is a fault which cuts the sedimentary series in two, to the...

Jan 1, 1918

By Priyadharshini M. R., Premalatha K

"Abstract With the development in the construction of heavily loaded structures, the necessity of pile foundations has increased. For the transfer of heavy loads, it is mandatory that the piles need to be socketed in the underlying rock strata. The load transfer in bored rock socketed piles is by end resistance or the combination of shaft and end resistance which in turn depends on the length of the rock socket. The determination of socketing length of the pile at present is mostly based on a few factors which affect the pile load transfer mechanism. The effect of all the possible factors involved, need to be studied in proposing guidelines for the design of rock socketing length of the pile. Analyses are carried out using finite element analysis software (PLAXIS 3D Foundation) to understand the influence of the thickness of overlying strata for different socket lengths of piles in weak rock. From the load settlement curves, the influence of the overlying soil on the rock socket length isobserved and an effective rock socket length is proposed.IntroductionThe determination of socketing length of the pile at present is mostly based on a few factors affecting the pile load transfer mechanism, which sometimes give a better design and sometimes an uneconomical design. Too much socketing length results in more construction time and higher costs. Therefore, the effect of all possible factors involved need to be studied in proposing guidelinesfor the design of t h e r o c k socket length of the pile.The factors that affect the termination criteria of the rock socketed pile are the capacity requirement, thickness and properties of the overlying soil, characteristics of the founding strata, drilling tools used, roughness of the rock socket and nature of loading.A comprehensive study was performed to understand all the above mentioned factors in different types of rocks. In this paper discussion is made on the settlement results, specifically the influence of overlying sand of different densities above a weak rock. The influence of stress developed is not discussed, keeping in mind the size of the paper under study."

Jan 1, 2014

By Robert W. Schaut

The use of micropiles is increasing for new construction and to retrofit distressed foundations in expansive soils. Typical micropiles in expansive soils have a lower section where the micropile grout is embedded in direct contact with the soil, and an upper section that is cased with rigid PVC pipe or other material to reduce the friction between the micropile and the surrounding expansive soil. In the upper cased section, the micropile grout is in direct contact with the inside of the casing. During construction, grout can flow upward into the annular space between the soil and the outside of the casing as the grout is tremied into the micropile. Thus, various interfaces may exist in a typical micropile, including soil-to-grout, grout-to-PVC, and soil-to-PVC. As the surrounding soil heaves, shear stresses are mobilized along the interfaces. The frictional characteristics of the interfaces are design variables that must be evaluated. For this study, an experimental program was conducted to evaluate the shear strength of the three interfaces listed above. Conventional direct shear testing was performed at a commercial testing laboratory. In addition, specialized testing was performed at Colorado State University (CSU). For the CSU testing, an interface testing protocol was designed using a modified triaxial cell to allow evaluation of the interface characteristics between rigid PVC and cylindrical specimens of grout or clay soil. It is shown that the shear strength of the soil-to-PVC and grout-to-PVC interfaces are similar, both of which are significantly lower than the shear strength of the soil-to-grout interface. This indicates that the use of a PVC casing in the upper portion of a micropile has a positive effect in reducing friction and the shear stresses resulting from expansive soil.

Jan 1, 2011