Search Documents

By John D. Smith, Robert J. Mitchell

"There is a world-wide trend toward underground bulk mining methods employing hydraulically placed backfill. This trend is recent and therefore there is little in the literature to assist an operator in the design of backfill properties, the design of drainage facilities, the calculation of the operating forces on a bulkhead, and the control procedures considered necessary before, during and after pouring. This paper presents recommended procedures that are based on over to years of experience in the various aspects of backfilling large openings. Free-draining timber or concrete block bulkheads are shown to be a viable alternative to massive reinforced concrete bulkheads for the containment of backfill pours. Hydrostatic pressures cannot develop in backfills provided adquate drainage facilities are installed.IntroductionThe increasingly adverse relationship between mining costs and mineral values has led mining companies to develop more productive, lower-cost, bulk mining methods. This has led to the increasing use of large, more or less continuous, hydraulically placed backfill pours to enable the recovery of a higher proportion of pillar ore. The success of any bulk mining method depends on the degree of stability maintained during the stoping operations with reference to the mining rate, the performance of the backfill with respect to the per cent extraction of pillar ore, and the control of the mine structure with respect to safety and productivity. One such method has been previously described(I) where a steeply dipping orebody is being mined with a sub-level method that employs large, hydraulically placed tailings pours for delayed pillar recovery. The paper describes the rock mechanics analysis undertaken to establish the stope and pillar geometry and the approach taken to establish backfill strength requirements to prevent dilution during pillar recovery. Production with this method started in 1970 and because few, if any, large bulk pours had previously been used in- this way (judging by the lack of information in the literature), design data and criteria were needed for several aspects of the work. Methods to establish backfill quantities and pertinent ""in-place"" fill properties are described in 2, 3 and 4 in the list of references. Results of field measurements taken to establish fill pressures for bulkhead design purposes are described in 5 and 6. Laboratory large-scale model tests undertaken to confirm a fill strength design equation, which takes into account fill arching, have recently been completed. A paper describing these tests and the results will be forthcoming in the near future."

Jan 1, 1982

By G. R. Cope, J. S. Getsinger, K. D. Lund, T. Neale

"Mineral exploration in the Sicker Group, a belt of Paleozoic volcano-sedimentary rocks on Vancouver Island, has traditionally centred on auriferous polymetallic volcanogenic massive sulphide deposits such as those currently mined by Westmin Resources Ltd. near Buttle Lake. Recently, however, the focus of exploration in the Sicker Group has shifted toward targets of structurally controlled gold concentrations, with notable success. Major north and northwesterly-trending structural features such as the Cowichan-Horne Lake break (one of several regional high-angle thrust fault s active throughout a long period of geological time) and related fault systems have contributed to localization of gold mineralization.Using the extensive information database compiled by MPH Consulting Limited during numerous exploration projects in the Sicker Group, two cross sections through areas with significant gold occurrences southeast of Port Alberni are presented. The cross sections combine geological, geochemical and geophysical data in an attempt to emphasize the relationship between structural trends and gold mineralization. Examples from specific properties, including gold discoveries along the Mineral Creek fault zone, are used to illustrate this relationship."

Jan 1, 1990

By Alan J. Wianwright

Introduction ??New world-class Upper Devonian porphyry Cu-Au system located in south Mongolia ??6.5 km NNE-trending mineralized corridor ? 4 discrete deposits ??Southern Oyu deposits: Chalcopyrite, deposits: bornite ??Hugo Dummett: Zone: Hypogene chalcocite in addition to chalcopyrite and bornite ??Total resource exceeds ~2 Gt@ >1% Cu, >0.25 g/t Au (0.6% Cu equivalent cut-off) (Ivanhoe Mines press release, 2005)

May 1, 2006

?Hydrothermal breccias-genetic models ?Deep drilling-underground potential ?Deposit variety-test new ideas Exploration Summary

May 1, 2006

By D. H. Rousell

"Rocks of the Whitewater Group (Aphebian age) oc ithin the Sudbury Basin and consist of three formations rre, from oldest to youngest: Onaping, heterolithic breccias lus an igneous-textured component; Onwatin, argillite and siltstone; and Chelmsford, greywacke with minor argillite with siltstone. Mineralization in these rocks is as follows:1) Sulphides are disseminated throughout the Onaping Formation. Pyrrhotite, the major sulphide mineral, occurs mainly as fragments; other sulphides are chalcopyrite, sphalerite, galena, pyrite and marcasite.2) Zn, Pb, Cu, Ag and A u mineralization in the Vermilion member, a carbonate-chert unit near the base of the Onwatin Formation (Vermilion and Errington mines).3) Pyrite and minor base metals in the Onwatin Formation .4) Mineralized quartz veins, located at or near the base of the Onaping Formation, include such deposits as Moore Lake (Pb, Zn and Ag), Foisey (Zn, Pb), Papineau (Cu, Au and Co) and Proulx (Pb, Zn, and Cu). Quartz-carbonate veins in a meta-gabbro sill contain Cu, Zn, As and Au. Material from quartz veins from two former ""gold mines"" (Gordon Lake and Creighton) yielded no Au values.5) Anthraxolite veins in the Onwatin Formation .The mineral occurrences can be explained in term of either the volcanic theory or meteorite-impact theory of basin formation. According to the latter theory, the sulphide fragments in the Onaping Formation may have been formed by the brecciation of sulphide-rich pods located in the upper mantle and at the base of the transient crater; some of the sulphides may have been derived from target rocks of the Huronian Supergroup. The Vermillion-Errington deposits may represent sedimentary exhalative deposits of the Remac type; mineral-rich brines, trapped at the base of the transient crater, rose upward and precipitated the mineralized carbonate-chert under reducing conditions. These conditions continued throughout the deposition of the upper Onwatin Formation but pyrite was the only sulphide that formed.The quartz veins were emplaced during the time of basin deformation. Metamorphism remobilized and concentrated carbonaceous material in the Onwatin Formation 10 form the anthraxolite veins."

Jan 1, 1984

By J. S. Fox

"Besshi-type Cu-Zn (-Ag-A u ± Co) deposits are tabular, stratiform volcanogenic sulphide bodies which are usually associated with mafic volcanic rocks of oceanic or intra-plate geochemistry, but which can also be found locally with ultramafic volcanics or subvolcanic mafic intrusions. A thick sequence of continentally-derived clastic sediment usually encloses both the mafic volcanics and the ore. Besshi-type deposits form subaqueously, in epicratonic rifting environments, more-or-less proximally, and as a result of hydrothermal convection in their subjacent mafic volcanic - clastic sedimentary piles. They belong to a rift -related metallogenic spectrum that includes sediment-hosted and Cyprus-type base metal deposits, and may diller genetically from these mainly with respect to rate and degree of crustal extension. Modern analogues to these deposits are f ound in the submarine volcanogenic sinters of the Gulf of California rift system.The associated lithologies and tectonic selling of Besshi-type deposits clearly distinguish them from Kuroko-type ores. This difference also seems to be reflected in their lead isotopic character. For example, leads from Besshi-type deposits in the Sanbagawa belt of Japan and from the Blue Ridge belt of southeastern U.S.A. lie on extended anomalous lead lines and have lowslopes in 207Pb/204 Pb - 206Pb/ 204 Pbspace (Sato and Sasaki, 1980; Leriuray, 1982), wheras those from most Kurokotype mining districts exhibit only narrow isotopic ranges and lie near or on the orogene growth curve (e.g. , Franklin et a I., 1981). More over, where Besshi- and Kuroko-type deposits are found in the same orogene, the former often occur earlier in the tectonic cycle than the tatter (e.g., Japan, the Norwegian Caledonides, the southern Appalachians and south-central Finland).Besshi-type deposits are not confined to any particular part of the world, or to any geological epoch. Moreover, in many mineralized belts, Besshi-type deposits are the predominant volcanogenic ore type. On a world-wide scale, deposits of this type therefore constitute an important base metal resource."

Jan 1, 1984

By Dave Thomas

?Uranium is a common trace metal at the earth?s surface, but these are amazing super-high grade (up to 25%) pods, veins and disseminated uraninite (UO2) near unconformities between Proterozoic siliciclastic red beds and metamorphic basement with graphitic metapelite and radiogenic granite. ?Pitchblende fills extensional features in reactivated fault zones and replaces matrix in sandstone ?One mining district in Canada ?the Athabasca Basin ->30 deposits /prospects -most in eastern ¼of basin -produces 1/3 of world?s U -employs northerners -VERY high tech -VERY high safety standards Unconformity-associated uranium depositsUnconformity-deposits

May 1, 2006

By Ronald B. DeDiemar

This paper will present the intrinsic factors of a cone crusher that affect performance, develop and define an ideal feed gradation for a cone crusher and, finally, bring out an important new development in computer design of crushing chambers and show an ability to predict crusher performance without trial-and-error methods.

Jan 1, 1979

By Peter A. Hacquebard

"Two continuous coal zones occurring in a 2500f t (762 m) thick section of the Upper Carboniferous Pictou Group (Westphalian C and D) have been encountered in five offshore wells drilled f or oil and gas in the Gulf of St. Lawrence. They correlate, by means of fossil spores, with thick coals of the Mabou and Inverness coalfields situated at the eastern margin of the Basin. Therefore, the presence of a large submarine coalfield of at least 18000 sq mi. (46 620 km'] is indicated. This compares with an estimated size of 14 000 sq mi. (36260 km' ) for the Sydney Coal Basin.Accessibility is provided only by the small onshore parts of the Mabou and Inverness fields, because farther offshore the coals lie too deep to be mined (below 4 OOO f t ([ 219 m)).Two near-shore coal exploration wells indicate that at Mabou Mines the younger Inverness coals occur at a mineable depth to at least 5 km from land. A structure contour map of this area shows a reserve of 125 million tons in two Inverness equivalent seams that are 8.5 ft (2.6 m) and 4.5 ft (f.4 m) thick. The Mabou coals, however, reach too great a depth close to shore to possess mineable resources.A structure contour map of the Inverness submarine area, based on mine data and one off shore seismic profile, indicates inferred mineable resources of 160 million tons, in two seams that are 7ft (2.1 m) and 4.5 ft (f.4 m) thick . A detailed deep seismic survey will be necessary to substantiate the structure and resource estimates"",Maceral and coal quality percentage diagrams of five column samples of these seams (the 7 Foot and 13 Foot Seams of Inverness Equivalents) show a bright banded coal, high in reactive macerals, which will produce a weak coke unsuitable f or metallurgical purposes. A thermal coal with a rank of H. V. ""B"" Bituminous (0.64% Ro) is present, averaging 12000 btu llb (6 660 kcai/kg), 10% ash and 6% sulphur, of which 60 to 80% is derived from pyrite.Microlithotype profiles of the major Mabou and Inverness coals show characteristic successions that can be used f or seam identification and proved valuable f or structural interpretations.The time of faulting in the major fracture zone on the eastern margin of the Gulf of St. Lawrence Basin has been deduced from coal rank variations. It occurred in pos tPermian, probably Early Triassic time."

Jan 1, 1986

By E. Barsky

"Theoretical notions of mass transfer processes in cascade separation of bulk materials have not been adequately developed as yet (Barsky M.D. 1980). In this paper we have derived linear difference equation of the second order for a cascade with initial feeding top any stage proceeding from mass exchange regularities. The solution of these equations has allowed us to determine quantitative dependences of the material distribution over the cascade stages, which serve the basis of the method of predictive estimate of the process results. We have also examined the model of the material distribution coefficient formation at individual cascade stages.We have checked the adequacy of this model to experimental data. It is noteworthy that the obtained theoretical results are phenomenological, i.e. they can be applied to the processes of separation of different physical nature, e.g. of isotopes, liquid media, gases, etc.INTRODUCTIONRecently, the processes of cascade separation of bulk materials have found broad application in various industries. They ensure a high separation efficiency and high-quality composition of final products. Although specialized literature gives serious attention to cascade processes [1], their theory is not sufficiently developed yet. To achieve optimal organization of this process, we examine mass transfer in a cascade gravitational classifier with stages of identical design."

Jan 1, 2016

By H. B. Sahu, N. M. Mishra, D. C. Panigrahi

The paper presents the development of a spontaneous heating liability index (SHLI) of coal based on a mathematical approach. The parameters for the calculation of this index have been determined by differential scanning calorimetric studies. Thirty-one coal samples representing both fiery and non-fiery coal seams of different ranks have been collected from different Indian coalfields and their SHLI values have been determined. In addition, the susceptibility of these samples to spontaneous combustion has been ascertained by standard crossing-point temperature measurement. The moisture percentage of all the samples has been obtained by proximate analysis. A comparative study between SHLI and crossing-point temperature, along with moisture percentage, indicates that SHLI predicts the proneness of coal to spontaneous heating more accurately.

Jan 1, 2008

Eagle Plains Resources? Exploration in the Northern Cordillera ?Eagle Plains Resources Ltd. (EPL) is actively exploring for Zn-Pb deposits in the northern Cordillera in both carbonate-hosted and shale-hosted (sedex) environments. ?This presentation will review some of the significant carbonate-hosted Zn-Pb showings occurring in the Mackenzie Mountains, NWT and make limited comparisons with sedexdeposits in the adjacent Selwyn Basin.

May 1, 2006

By H. Z. Liu, J. M. Zhao, F. C. Wang

"Novel silicate-alginate composite beads containing 2-ethylhexyl phosphonic acid mono-2- ethylhexyl ester (P507) were synthesized and applied for the adsorption of Nd3+ from aqueous solutions. The adsorption amount of Nd3+ has been increased owing to the introduction of P507. The effect of equilibrium pH (pHe), the kinetic and isotherm experiments were investigated. The adsorption reaches equilibrium at 9 h and the maximum uptake capacity is up to 195.4 mg/(g dry adsorbent). The Langmuir isotherm equations are used to describe the adsorption process. Complete desorption can be realized with 0.2 M HCl within 20 min. INTRODUCTIONRare earth elements (REEs) have found various applications in different domains, such as metallurgy industry, ceramic industry, nuclear fuel control, photo-electro-magnetic functional materials owing to their unique properties. Neodymium (Nd), as a representative of all of the most valuable REEs, is widely used as catalysts, laser crystals, capacitors, rubber additives, Nd-Fe-B magnets, hydrogen storage and so on. Thus, the separation and purification of neodymium is significant. Unfortunately, Nd always coexists with other REEs and selective separation of the individual Nd from the REEs mixtures is still extremely difficult owing to their strictly similar atomic structures and chemical properties.Liquid-liquid extraction (LLE) and solid-liquid adsorption (SLA) are the most widely adopted techniques for the separation of REEs in the hydrometallurgical fields. The LLE process is well suited for large-scale continuous operation because of its inherent high capacity and fast kinetics. Nowadays, as a commercial extractant, 2-ethylhexyl phosphonic acid mono-2-ethylhexyl ester (P507) has been extensively studied for extraction and separation of REEs since it has considerably good extractability and high separation efficiency (Xu et al., 1992). SLA is one of the effective and green separation methods with some prominent advantages, such as easy regeneration of adsorbents, small footprint size, less industrial wastes, higher enrichment factors and column efficiency,rapid solid–liquid separation without emulsion and so on. Hence, the introduction of extractants with excellent performance into adsorbents will integrate the advantages of LLE and SLA (Lee et al., 2009)."

Jan 1, 2012

By J. S. Stewart

THIS paper was prompted by a persistent demand for what information we have that will throw light on the oil and gas possibilities of the Maritime Provinces. The problems involved were made familiar to the writer during three seasons of field work in New Brunswick and Nova Scotia. The reasons for renewed interest are: (1) In many parts of that region, the surface is underlain by a thick series of unaltered sedimentary rocks. (2) Oil seepages occur, and oil in commercial quantity has been exploited' near Moncton, New Brunswick, for many years. (3) In recent years, a new method of attack has been developed toward the finding of stratigraphic traps. This method is based on a detailed study of the geological history of the region, as revealed in surface outcrops and samples from deep wells. The well samples show the lateral variation of strata, far from any possible surface outcrop of the same beds. Sufficient work has now been done in the Maritime Provinces to reveal the broad features of the geological history and the character and distribution of the various rock formations. Comparatively little deep drilling has been done in this region, but the holes are widely scattered and the samples from them have added much to the information obtained from the numerous outcrops of bed-rock. The following discussion gives a summary of available information that has a bearing on the subject.

Jan 1, 1943

By D. A. Jacobson

Mining operations, whether new or existing, are constantly looking for ways to maximize production and improve energy efficiency, while keeping the footprint required to a minimum. The Nordberg MP1250 cone crusher was designed with these three goals in mind. A series of side-by-side evaluations comparing an MP1250 to an MP1000 were completed at two Freeport-McMoRan operations. The first evaluation began October 2009 in a tertiary position and the second began March 2010 in a secondary position, where it remains in full production today. Utilizing 25% higher power capacity than the existing MP1000 tertiary crushers, the MP1250 had 29% higher capacity and 17% lower specific energy, adjusted for differences in feed and product size. The MP1250 compared to the existing MP1000 secondary crushers achieved 30% higher capacity at a slightly reduced specific energy, while achieving a finer product. The MP1250?s higher capacity and energy efficiency may have application in many crushing plants. Depending on site specific economic factors, greenfield projects may benefit from a smaller footprint and less ancillary equipment, whereas brownfield projects may benefit from higher capacity or a finer product within the same footprint.

Jan 1, 2012

By Jean-Paul Drolet

"The ultimate aim of the Law of the Sea Conference, held under the auspices of the United Nations, is to ensure that all aspects of the use of the sea are covered by international law. The question facing the nations of the world can be stated as: "" Who will control and benefit from the use and the wealth of the sea?""The United Nations Conference on Law of the Sea - known as UNCLOS - which reconvened in New York during the latter part of August 1978 was the third such Conference in the UN's history. The concepts of sovereignty over the territorial sea and freedom on the high seas have remained fundamental to the international law o f the sea until our time. The legal regime based on these two concepts developed initially from state practice meant that the unilateral actions taken by one or more countries were eventually accepted and followed by others.It was not until 1958, during the first Geneva Conference on the Law of the Sea (pursued in a second Conference in 1960) that the Law of the Sea was codified and modified to a certain extent by the then independent nations of the world in the four multilateral conventions on territorial sea and contiguous zone, continental shelf, high seas, and fishing and conservation of living resources.A third Conference got under way many years later when the members of the UN met in New York at the end of 1973 for preliminary discussions . This meeting stemmed largely from the need to fill gaps in existing international legislation which did not cover the new uses of the sea. The Conference was subsequently reconvened a number of times - in Caracas (1974), in Geneva (1975) and twice in New York (1976) for what was called "" substantive negotiating sessions."" A sixth session was held in New York in 1977; a seventh, held in Geneva at the beginning of 1978, recessed and reconvened in New York at the end of August 1978. This is what is referred to, in international jargon, as the seventh session of the Third United Nations Conference on the Law o f the Sea. The following dates are the principal markers of a saga which began some twenty years ago with the purpose of regulating the use of the oceans."

Jan 1, 1981

By A. Y. Senchenko, Y. V. Kulikov

"Different methods aiming at specific energy calculation and design of AG/SAG circuits are used in mining. They include JK DWT/SMC test, SAGDesign test and CWi/RWi/BWi tests. The simplest methods with no secret equations and giving energy required for grinding in kWh/t were proposed by F.?. Bond and J.H. Starkey. D.J. Barratt proposed to use results of CWi/RWi/BWi tests for AG/SAG mill sizing. The present paper gives an alternative for forecast of specific AG/SAG energy. The principle is similar to the theory proposed earlier and consists in cumulative AG/SAG energy calculation using indices of rod and ball grinding (RWi+BWi) without impact crushing index (CWi). Then total energy is divided between two grinding stages using special formulas based on extensive statistical information. The forecast indices of AG/SAG and ball grinding are similar to the SAGDesign testing results. Hereinafter the predicted indices are used for mill sizing of the whole grinding circuit. The method considered in the paper enables prediction of AG/SAG energy based on the test results according to Bond method. The proposed method version was not widely published earlier. The aim of the work was to elaborate cost-effective, reliable and accessible way to determine specific AG/SAG energy. At this stage of method development, it is recommended to use it only for works at preliminary Geometallurgy stage (Scoping, Pre-Feasibility). At design stage the obtained data should be confirmed by appropriate testing using alternative JK DWT/SMC and SAGDesign methods.INTRODUCTIONAppropriate crushing and grinding testing is required to design efficient comminution circuits. It is obviously important to obtain accurate information about ore hardness properties since the main energy consumption at the plant is associated with comminution processes. Moreover, it is required to apply the processes that make it possible to minimize operating costs and efficiently use capacity of the installed equipment installed.When studying ore hardness properties, it is required to take into account that breakage of the material is performed using different equipment. That is why accurate selection of the equipment and the circuit calculation without relevant testworks is impossible. Ideally, the testworks should provide answers to the following questions: determination of ore hardness properties, determination of specific energy consumption for comminution as well as obtaining of sufficient amount of statistically significant results from the tests. The results from crushability and grindability testworks in the first place provide assessment of ore hardness properties and in addition correlate with throughput of the respective equipment. The data obtained can be used for modeling of comminution circuits at the stage of the technology development"

Jan 1, 2016

By T. G. Joseph

ABSTRACT: The Canadian oil sands provide some of the harshest mining conditions in the world. Asoperations demand ever bigger tools, the toll on large mobile mining equipment is high, with structurallife often half of that expected. Soft ground conditions predominantly lead to fatigue failure scenarios, poor stability, and inconsistent payload evaluations. These challenges are not solely a concern for Canadian oil sands mines; there are far-reaching implications for surface mining equipment in any poor ground-operating environment. This paper focuses on the basics of payload evaluation, motion response and a simple estimate of structural life for haulers.

Jan 1, 2011

By L Munholand, G. Soucy, P. Quintal

This work presents early results from the first study to optimize the hydrodynamics of a Plasma Lift Reactor (PLR). The PLR is designed to break down organic contaminants in aqueous solutions. New experimental results are presented for air/water tests and for plasma degradation of organic contaminants in Bayer liquor. In addition, a multiphase Computational Fluid Dynamics (CFD) model has been developed which predicts the hydrodynamic behavior in the PLR. These results of this work suggest the PLR is effective at reducing contaminants in the Bayer liquor and that the CFD model adequately describes the hydrodynamic flow.

Jan 1, 2005

By Chuanhui Cao, Shimei Liu, Xiaojing Li, Yueyuan Zhou

"Force analysis on weakly-magnetic particles and non-magnetic particles in magnetic field are presented, using a kind of permanent magnetic drum magnetic separator, which is designed with strong specific magnetic force and open magnetic system. Its surface peak intensity reaches to 1.0T, and the distribution density of capture line is 1.25×103/dm2. Qualitative analysis on the particles including its magnetic property, particle size, motion speed, magnetic field intensity, etc. is also presented to calculate the separating parameters for the drum separator. Experiment was conducted for the separation of fine weakly magnetic minerals for example ilmenite. The practicability to separate the minerals using separator designed with open magnetic system has been proved, providing an economic way for efficient separation of micro-fine weakly magnetic minerals and upgrading of non-metallic minerals. INTRODUCTIONMagnetic separation is a mineral processing method based on the differences of magnetic properties between minerals in inhomogeneous magnetic field (Sun, 2007). Currently for separation of micro-disseminated weakly magnetic iron ore, electromagnetic high intensity magnetic separators with closed structure of magnet system are often used. And for the separation of strongly magnetic minerals such as magnetite, low intensity drum magnetic separators with open magnet system are often used. In order to lower the operation costs and improve energy efficiency, it is important to develop efficient high intensity permanent magnetic separator with open magnet system, to some extent replacing high intensity electromagnetic separator.Oberteuffer (1974) discussed the magnetic force and competing forces in magnetic separators which compete with the magnetic forces and act on all of the particles which travel through the separator are those of gravity, hydrodynamic drag, fraction, and inertia in magnetic separation."

Jan 1, 2016