Search Documents

By Z. D. Hora

Sand and gravel resources of the southern coastal region of British Columbia may be linked to various episodes of Wisconsin glaciation. During Wisconsin and probably earlier times, the Fraser Lowland and coastal areas were subjected to repeated glaciations separated by non-glacial intervals. Each major glaciation was accompanied by isostatic and eustatic changes in sea level up to 200 m or more. As a result, the Lowland was covered by the sea during much of Quaternary time. Because the Fraser Lowland is surrounded on two sides by high mountain ranges, glaciers terminated in the sea during their maximum advance. Therefore, meltwaters released during deglaciation, together wit h retreating glacier ice, could produce widespread and extensive sand and gravel deposits both along the coast and throughout the Fraser Lowland and adjacent areas.

Jan 1, 1984

By K. Barron

"A computer program is described which will analyze the stability of coal pillars. The extent of the peripheral failed zone and the central elastic core of the pillar, the stress distribution across the pillar and its strength can be determined by a ""sliceby- slice"" analysis technique. The program incorporates a brittle/pseudo-ductile transition point so that a pillar may fail by brittle fracture or pseudo-ductile yield. It is shown that:(i) There is a minimum pillar stress below which fracture cannot initiate; hence there is a minimum pillar strength. (ii) In specific circumstances (narrow pillars) , once fracture initiates at the pillar edge it must propagate immediately to the pillar centre. This unstable situation is called ""catastrophic"" failure and might be regarded as a model of a pillar ""burst "". (iii) For wider pillars, the failed zone ex tends gradually into the pillar as the loading increases until it reaches the pillar centre when the pillar is deemed to have f ailed. This is called the point of ""ultimate"" failure.The critical pillar widths to avoid catastrophic and ultimate failure can be calculated.A hypothetical analysis of five rib pillars is given to illustrate the application and the results obtained from the model. The model is then used to analyze three case histories taken from the literature. The first demonstrates the applicability of the brittle/pseudo-ductile failure criteria for Pittsburgh coal. The second compares the pillar strength formulae derived here with those of Salamon and Munro(13) and Bieniawskiou . The final case history compares the model analysis with field stress measurements in a yielding pillar. In all cases the model results are compatible with the case histories."

Jan 1, 1984

By Robert D. Brown

"The Conservative Government 's budget proposals brought forward on December 11, 1979 have been withdrawn, but they are far from dead. On the contrary, a number of those budget proposals, especially the ones which would close loopholes and result in other technical changes being made to the Income Tax Act, should be considered to be alive and well.It is not unreasonable to expect the next government, of whatever political persuasion, to reintroduce many of these technical changes in the next federal budget. For that reason, last December's budget may have offered an interesting preview of what the mining industry and other taxpayers can expect in 1980. It is quite possible that some of these changes may be effective as of the original dates announced in the withdrawn budget proposals.This month, ""Tax Notes"" reviews the main pro visions of Mr. Crosbie's December, 1979 budget, with a primary focus on the changes that would have affected the resource sector.It must be emphasized that all of the budget proposals discussed herein have been withdrawn, that none of them are law and that any actual changes in our tax rules will have to be dealt with by the new Parliament that will be assembled following the February 18 election. December 1979budget withdrawnThe federal budget proposals brought forward by Finance Minister John Crosbie on December II, 1979 were withdrawn as a result of the defeat of the Conservative Government on a motion of non-confidence in the House of Commons on December 13. However, it appears quite possible that at least some of the proposals may be introduced into Parliament at a future date, possibly with retroactive effect.In a press release issued by the Department of Finance, Finance Minister John Crosbie stated that if the Conservative Government is returned to power, it will reintroduce all of the measures contained in his December II budget.Mr. Crosbie stated that all of the income tax measures contained in the budget would be reintroduced, effective on the dates indicated in the Notice of Ways and Means Motion tabled on December II. Some of the more important measures in December II budget, and their effective dates as indicated in the Notice of Ways and Means Motion, are discussed below.The December budget had also introduced or increased excise taxes or duties on gasoline, wines, cosmetics and photofinishing. If the Conservative party is re-elected, these measures will be reintroduced with prospective effect (i.e . effective as of new dates to be announced in the new budget)."

Jan 1, 1980

By J. N. Hilton, D. Moffett, E. Barnes

"A recent pilot-plant program carried out at Rio Algom's Quirke uranium mine at Elliot Lake, Ontario is described. The goal of the research was the production of tailings basin effluents which were low in total radium-226. The process tested involved precipitation of radium with barium chloride and sedimentation in plastic-lined settling ponds. Adjustment of the tailings basin overflow from its normal value of pH 9.5 by addition of sulphuric acid to about pH 7.5 was found to give approximately a five-fold improvement in total radium-226 removal. A five-month demonstration test resulted in an effluent with a mean total radium-226 activity of44 pCi/L after 2.5 days settling time and 29 pCi/L after 5 days. The results from the demonstration program are used to propose a schedule of achievable total radium-226 activities where precipitation and sedimentation are employed. The maximum suggested values for 5 days nominal settling time are: 30 pCi/L in an annual mean, 45 pCi/L in a monthly mean. 60pCiIL in a weekly mean and 80 pCi/L in any single grab sample.IntroductionRadium-226 has been removed from effluents at the Elliot Lake uranium mines since the introduction of the first barium chloride treatment system in 1965. Current practice, which has changed little over the years, consists of radium-barium sulphate precipitation by the addition of a low do se of barium chloride to the clear overflow from the tailings basin(l·2l. Provision is made for the precipitate to settle in large natural or constructed ponds and lagoons. The residence time in these ponds, which depends on the site, ranges from 3 to 35 days, with varying degrees of efficiency being achieved."

Jan 1, 1981

By John C. Taylor

"The non-ferrous pyrometallurgical industry has been under extreme pressure since 1980 and significant changes are taking place, principally in the copper, nickel and lead industries. This paper reviews some of these changes, particularly with respect to smelter capacity, major technical trends, and the industry's response to increased energy costs and environmental constraints.The Canadian metal mineral production for 1985 has been estimated at a value of over $8 billion, of which half is derived from copper, nickel, lead and zinc production. It is in our national interest that the Canadian industry remain competitive in the world market and continue its traditional contribution to the Canadian economy. IntroductionPyrometallurgy by definition requires energy, usually in the form of fuel, and produces process gas streams which can no longer be discharged directly to atmosphere in most countries. While the industry has been under varying degrees of pressure over the past fifteen years, it is just since the early 1980s that major changes have taken place, due, to a large extent, to an oversupply on the primary metal markets and depressed prices. These factors, combined with a surge in the price of oil, have resulted in some trends developing which must be recognized by those in the industry who plan to be in operation and competitive in the next decade.Although the value of Canada's mineral production, in terms of constant dollars, has decreased by more than 35% over the period from 1980 to 1985, the bulk of this production is exported and the industry still makes a significant contribution to the Canadian economy."

Jan 1, 1988

By J. C. Farge, G. G. Jacox

"The effect of composition and process variables on the properties of Marmet and modified Ni-Hard slugs will be discussed. The effect of shape on the over-all performance of grinding media and its relationship to the end product has been investigated and these results will be reviewed. The cost effectiveness of slugs versus balls has been well documented under various operating conditions and this will be presented in detail. IntroductionThe selection of grinding media is based on the cost-to-wear ratio combined with the consideration that it must stand repeated impacts without breaking. The specific consumption of grinding balls and slugs depend s primarily on their microstructure, which, in turn, is controlled by chemical composition and by the processing condition s to which they are subjected during manufacture.The first part of the paper deals with the optimization of alloy content to produce cast iron slugs with microstructures consisting essentially of marten site and carbide and with hardnesses of 650 B.H.N. and higher. The second part deals with the use of cast iron slugs to replace forged steel balls in milling operations. Tests indicate that the shape of the media has little if any effect on results and that the hardness and microstructure of grinding media will determine its relative performance. Where price is equal under similar milling conditions, the cost effectiveness of cast iron slugs is superior to that of forged steel balls.In order to understand the role of alloying elements in cast irons, it is judicious to consider the microstructural changes which occur during solidification and subsequent cooling, particularly from above the eutectoid temperature. Solidification starts with the formation and growth of dendrites of austenite. As temperature decreases, an eutectic nucleates and grows between the primary austenite dendrites. Immediately after solidification, the structure consists of proeutectic austenite and of the eutectic of primary carbides and austenite. On cooling to room temperature, austenite can be retained or transformed to pearlite, bainite, martensite or mixtures thereof. It is necessary to prevent decomposition of austenite into pearlite by adjusting the alloy content. For best abrasion resistance, the microstructure at room temperature should consist essentially of martensite and carbide. These types of irons are known as ""martensitic irons "". Depending on the carbon content of the austenite and cooling rate, "" as-cast"" martensitic irons will contain different proportions of martensite and retained austenite. The more carbon in solution in the austenite, the lower is the temperature at which the martensitic transfoemation takes place. By the time room temperature is reached ., the transformation is seldom complete, and the end product is generally a mixture of martensite and retained austenite."

Jan 1, 1980

By Elma van der Lingen

Gold is considered the most inert of all metallic elements, but the metal can show catalytic activity when prepared by specific techniques. Preparation techniques being used to prepare gold catalysts systems mainly involve precipitation methods incorporating gold compounds or complexes. This paper introduces a totally different method for the preparation of gold-based heterogeneous catalysts that can be used for oxidation and reduction reactions, as well as electrocatalysts. The method involves alloying of gold with a less noble metal, such as aluminium, to form a gold-containing intermetallic precursor. AuAl2 was produced by melting gold and aluminium together in a vacuum arc furnace under a protective atmosphere. The aluminium is then dissolved from the AuAl2 precursor by means of NaOH to produce a highly porous gold structure. The paper also reports on a method of incorporating transition metal oxide(s) with the porous gold to form an active heterogeneous catalyst. Promoter elements can also be melted with AuAl2 to improve catalytic activity. Alloying has the advantage that the promoter element can be in contact on atomic level with the gold. In-situ xray photoelectron spectroscopy (XPS) studies have also been done on the porous gold catalysts to further clarify the CO oxidation mechanism on gold-based catalysts.

Oct 1, 2003

By J. Carr

This paper discusses: (1) the need for Western Canadian coal in eastern Ontario Hydro plants; (2) design parameters-unit trains, year- 'round receiving from trains, and shipping (Great Lakes season); (3) equipment chosen-dumper-indexer, outhaul conveyor, yard belt, stacker, reclaimer, surge-bin feeders, shiploader, docking system and dust control; (4) foundation and soil conditions-dumper house, yard belt, surge bin and dock-piling-runway; (5) winter conditions- thaw shed, feeder, lump breaker, beltings (oil), and dust control and disposal; and (6) operations to date.

Jan 1, 1979

By Stephen C. Tadolini

"The use of a torque wrench to establish the amount of actual load developed on an expansion anchor bofting system dates back to work completed in the early 1950s. The advent of ultrasonic measurement systems and hydraulic torque wrenches has made it possible for the U.S. Bureau of Mines to perform torque-tension measurements in the laboratory and the field much more accurately. The results indicate that the amount of initial boft preload may be overestimated by amounts in excess of 45% of the expected load using torque wrenches. This inaccuracy is primarily due to the friction that occurs between the bearing plate and the head of the boft. These parameters become extremely important when the support system is being used to prevent joint members from slipping relative to each other or when the boft acts as a heavy spring to clamp two or more sections together. Methods to overcome the frictional losses are presented in conjunction with a laboratory method to determine the actual torque-tension ratios for expansion anchor and combination bolting systems.IntroductionMechanically anchored roof bolts have been widely used in the mining industry since their introduction in 1947. Estimates made in 1989 indicate that out of 85 million fixtures, approximately 49 million bolting fixtures still use applied tension to complete the reinforcement necessary to maintain stable openings. Nearly 85 million bolts are used yearly. The most widely used bolt is the resin-anchored headed rebar, followed by standard mechanical roof bolts, specialty bolts (mechanically anchored, resin enhanced fixtures) , and combination bolts . Po st-tensioned resin rebars, combination systems, and friction stabilizers make up the remaining 10% of the units used (Fig. I).For mechanical, combination, and tension rebar bolts, the bolt tension is the primary means of reinforcing the roof, but in many cases, because of poor installation procedures, the bolts are ineffective. Mine operators recognize the importance of proper installation procedures. Long-term bolt tension measurements are required in the Code of Federal Regulations (CFR)In each bolting cycle, the actual torque or tension of the first tensioned bolt installed with each drill head shall be measured immediately after it is installed. Thereafter, for each drill head used, at least one roof bolt out of every four installed shall be measured for actual torque or tension. If the actual torque or tension of any roof bolts measured is not within the range specified in the roof control plan, corrective action shall be taken."

Jan 1, 1991

By E. M. De Souza, R. Penner

"Water is encountered at the majority of underground mines, both over their lifetime and during each stage of development and production. The dewatering system is one of the most important and costly components of an underground mining operation and it is often not well designed and analyzed. An effective design of a mine dewatering system will greatly reduce its energy cost as well as improve working conditions and reduce production costs. A computer-based system, called Qpump, has been developed to assist the underground operator to effectively design and/or assess over-all and local mine dewatering systems. The design features and principles used in the development of Qpump are introduced and an example which illustrates typical applications is presented.IntroductionTraditionally, dewatering operations have been given lower priority than many other operations in underground mining. Invariably water will be encountered during the sinking of the mine shaft, during development and subsequent production. The dewatering system thus becomes a very important component of an underground mine operation and, in fact, any mine manager will attest to the importance and necessity of an efficient mine dewatering system.The water problem is of varying importance at different mines. There are several factors that contribute to the water encountered. It is a function of the mining method and techniques utilized (backfill system, drilling and raising technology, dust control sprays, shaft water rings, etc.) and of prevailing conditions (ground water, rock structure and permeability). In some cases a mine may be so dry that little pumping is required while in others, the weight of water pumped may exceed by many times that of ore mined.The successful design and application of a mine dewatering system is dependent upon the operating conditions of each specific operation. There are no standard procedures and systems which can be used for all mining situations. However, an effective water system will greatly reduce the energy and production costs of a mine, improve working conditions and eliminate headaches because of flooded working places."

Jan 1, 1993

By Matt Manson

?? Current Exploration and Assessment ?? Overview of Potential Development ?? Infrastructure ?? Opportunities and Challenges ?? Renard? 1-10 kimberlite pipes and ?Lynx-Hibou? kimberlite dyke system within ?Foxtrot? property ?? 50/50 Joint Venture between Ashton (a subsidiary of Stornoway) and SOQUEM ?? Discovered 2001-2003 ?? Québec is routinely assessed as one of the top mining jurisdictions in the world ?? Agnico-Eagle Mines Ltd. Is Stornoway?s largest shareholder and a leading mine developer in Québec

May 1, 2008

By John C. Loretto

"The paper identifies two of the main problems encountered in recent hydrometallurgical plants for the recovery of gold and silver: firstly, the plant recovery is lower than anticipated from the testwork; secondly, the metallurgical accounting figures cannot be reconciled.The principal reasons for the plant recovery being lower than the testwork are discussed, together with solutions that can minimize these problems both during the design stage and during the plant operation after the problems have manifest themselves.The reasons for the difficulties in metallurgical accounting are analyzed by reviewing the various components of the plant figures. Recommended solutions are given for minimizing this problem and the realities of obtaining accurate figures are discussed.IntroductionThe start-up over the last few years of new hydrometallurgical plants for the recovery of gold and silver has brought to the surface again a number of problems. Most of the problems have existed for some time and they manifest themselves mainly in two ways. Firstly, the plant results do not agree with the metallurgical testwork figures; secondly, the metallurgical accounting figures do not balance.Metallurgical TestworkThe plant results not agreeing with testwork figures are mainly due to:a) testwork samples not representative of the eventual plant feed;b) misinterpretation or misunderstanding of testwork ;c) plant losses;d) plant design not allowing testwork results to be achieved;e) operating deficiencies."

Jan 1, 1982

By Daniel D. M. Adams

In 2004, Rio Tinto started a major project to implement Mine Monitoring and Control (MMC) systems worldwide. A detailed selection processes was undertaken and migration to a standard system was started. Today systems are operating around the world and serve as the core of to many business processes. Implementations include highly union areas, large mines, centrally managed mines, and remote areas. Each implementation has unique challenges but all are working towards the common goal with common systems. This paper reviews two projects that Rio Tinto has deployed in diverse conditions. The projects are the Rossing Uranium upgrade from the original Wenco system to the common standard and Iron Ore of Canada?s general technology upgrade. Also discussed is the future of mining at Rio Tinto, specifically the drill automation projects, and how it is utilizing the common standard MMC systems.

May 1, 2010

By Ali M. Ghazi, Ronald J. Goble, Lowell S. Whiteside

"Geerite (Cu1.6S) is a rhombohedral copper sulphide which occurs naturally in epitactic replacement of sphalerite; cell dimensions closely approximate those of the host sphalerite.Geerite-type structures can be produced by leaching digenite (Cu1.8S) in ferric sulphate solutions. X -ray diffract ion and electron microprobe studies indicate that eight metastable geeritetype structures can be produced, depending upon the concentration of f erric sulphate solution used and the duration of the each. Although compositions cluster on or near values observed for natural phases, optical properties indicate that we are dealing with polymorphs of these phases. Leaching of chalcocite (CU2Sj in dilute f erric sulphate solutions produces similar results. In contrast, leaching of chalcocite in more concentrated solutions seems to produce true analogues of natural minerals.During froth flotation, sphalerite is activated with a monolayer of floatable copper sulphide with the composition, CuS, of the mineral covellite. However, covellite is not significantly more floatable than sphalerite, and has an incompatible structure because of the presence of covalently-bonded atoms of sulphur. Leaching ofdigenite was used to produce a polymorph of covellite with a geerite-type structure, compatible with that of sphalerite. This polymorph has a flotational behaviour similar to copper-activated sphalerite, suggesting that the monolayer has a geerite-type CuS structure. IntroductionIn an ideal close-packed sulphide structure the distance between sulphur layers, D, is equal to 2R 2/3, where R is the radius of the sulphur atoms. In sulphides with covalently-bonded sulphur layers, such as covellite (Fig. I), D will be an average of the number of covalentl y-bonded and close-packed sulphur layers, weighted as to the relative number of each type of layer. Both D and R are spacings which are readily identifiable structurally and on X-ray diffraction patterns. Goblel has shown that for copper-iron sulphides with metal-to-sulphur ratios between 0 and 2 and copper-to-total metal ratio s between 113 and I there are strong correlations between composition and measured D and R distances (Fig. 2). D can be represented by a single empirical equation relating interlayer spacing to composition; R must be represented by three equations relating the radius of sulphur atoms to composition. One of these equations (R, in Fig. 2) represents ideal close-packed behaviour, the other two represent sulphur radii greater than (R1) or less than (Rh) the ideal."

Jan 1, 1988

"A 3-dimensional finite element model for stress/stability analysis of rock excavations in underground mines is presented. Developed for use on personal computer under OS/2 operating system, the model employs the 8-node isoparametric brick element and accounts for such loading conditions as in situ stresses and gravity loading of the rock mass. In addition, modelling of backfill in mine stopes as in situ stress-free material is incorporated. Material failure is assessed by Mohr-Coulomb or Hoek-Brown failure criterion. A mine design example is presented to illustrate the potential use of the model as a tool for stope design.IntroductionNumerical modelling of mine structures has become a vital tool for mine design in recent years. The need to maximize ore extraction ratio and to reach deeper mineral deposits underground has led the mining industry to employ numerical methods of analysis to undertake complex ground control studies in order to better understand the ground response to mining excavations and to evaluate the ground support requirements. Thanks to the rapid developments in computer technology, it is now possible to perform very comprehensive analyses including, but not limited to, 3-dimensional, elasto-plastic, or large deformation or time dependent nonlinear analyses on personal computer.During the past ten years or so, many researchers undertook 3-D finite element analyses of rock mechanics problems in mining engineering. The following is only a sample review. For example, Chan'!' used three-dimensional finite elements to study the mechanical response of jointed granite during shaft sinking at the Canadian Underground Research Laboratory. Wang et al.(2) performed 2-D and 3-D finite element analyses of room-and-pillar mining system with flat and rolling coal seams. Thatejatu used three-dimensional finite element method to examine the problem of branching tunnels. Dolezalovaw used three-dimensional finite elements for the analysis of tunnel-face advance with partial excavation as well as full-face excavation in combination with rein for cement of the face by long anchors. Peili (5) used three-dimensional finite elements for the simulation of rock-liner interaction near the tunnel face."

Jan 1, 1992

By J .. R. Brown, G. Deschenes

X-ray Photoelectron Spectroscopy (XPS), X-ray Diffraction (XRD) and Electron Probe Micro-Analysis (EPMA) were used to characterize chemically the gold complex adsorbed on activatedcarbon from a solution containing 102mglL Au and 0.5 giL thiourea. This paper also considers the gold chloride and the gold cyanide systems. The results indicate gold is adsorbed on activated carbon from the thiourea solution as the gold (I) thiourea complex, i.e. Au [CS (NH) 2];' Other gold species such as metallic gold were not detected on the carbon support. These results also suggest the elution of the gold (I) thiourea complex can be performed with high recovery.

Jan 1, 1993

By R. W. Thompkins

"PREFACEPart 1 of this paper, published in the September issue, covered the occurrence of uranium, radiation from uranium ores, the uranium series, radioactive theory, radioactive equilibrium and application to the radon series, the working level, the theory of emanation and diffusion, transport by thermal diffusion of radon emanating from porous rocks, and definitions.This Part 2, which follows, deals with radiation theory applied to uranium ores, other radon migration factors, factors affecting the radon gas release rate, the measurement of radon gas emanation rates, the tunnel concept, variation of emanation rate with grade and estimating radioactivity from grade analysis.The series will conclude with Part 3, in the November issue, which will discuss the techniques for controlling radiation and provide some example calculations.10.0. Radiation Theory Applied to Uranium Ores10.0.1. The processes of diffusion transport of radon gas, through rock from the fundamental physics is a function o f the radon gas concentration in the interstitial pore spaces and the distance from the surface. Expressed by Fick's first law of diffusion, it is expressed: [ ]10.0.2. The maximum concentration is a function of the emanating power (ß), thus the above equation may be expressed: [ ]10.1. The Effect of Porosity10.1.1. If a constant emanating power is assumed (ß), a family of curves can be obtained for concentrations at varying distances and rock porosities. The curves as originally plotted assumed a constant emanating power of 5 x 10-4 pico curies/litre/sec and show the maximum expected concentrations in the pores in pico curies per litre. Because these concentrations are proportioned to the emanating power, this set of curves can be structured to show the fraction of maximum concentrations possible at various porosities of the rock.10.1.2. Notice that at 10, 20 and 30% porosities a 5-cm sample (hand-sized and drill-sized pieces) has no practical increase in pore concentration. Thus, by measuring the emanating power of hand-sized pieces of ore, the actual radon gas production into any pile of broken ore could be estimated readily."

Jan 1, 1982

By Jose R. Hernandez-Aguilar

"This paper revisits data from previous studies (Hernandez-Aguilar, 2010, 2011) to better understand the link between metallurgical performance and bubble size (Db) in the collection (pulp) zone of full-scale flotation systems. To obtain conclusive evidence exclusively related to the collection zone, the experiments were designed in those studies to control both the bubble generation method and the influence of the froth zone on the overall metallurgical performance in industrial and pilot-scale flotation columns. The results showed that generating small (1 mm) bubbles had a significantly higher beneficial effect on the recovery of coarse (> 75 µm) particles compared to the effect on fine (< 16 µm) particles. It was observed that, under certain practical conditions, the recovery of liberated coarse particles was close to zero, but could be recovered almost completely by reducing bubble size. The evidence revealed an apparent inconsistency of the so-called “k–PSb” model: at constant froth recovery, increasing Sb did not always result in higher recovery, as the model predicts. Overall, the evidence showed that it was not the Sb but the bubble size that proved to be a more reliable link to metallurgical performance. Only under highly suboptimal bubble size conditions (Db = 3 mm) did the froth zone seem to play a role, possibly reflecting an effect of pulp-zone bubble size on froth stability. However, for the most part, both the bubble generation method and the froth zone played inconsequential roles. An empirical model that better describes the kinetics of particle collection is proposed.INTRODUCTIONStudies showing the link between metallurgical performance and the interactions of bubbles and particles in the collection (pulp) zone of industrial flotation systems are scarce. A common belief among a number of mineral processing practitioners considers that “small” bubbles are favourable to recover “small” particles and that, conversely, “larger” bubbles are more efficient at floating “coarse” particles. However, perceptions like this are often substantiated by anecdotal evidence rather than by rigorous data analysis. What is the optimum bubble size for a particular case, how operating conditions can be adjusted to control a target bubble size, and whether the bubble size needs to be changed in the first place to optimize the operation of a flotation plant are questions that usually remain without solid answers.The studies reported by Hernandez-Aguilar (2010, 2011) were, in part, performed to test the effect of bubble size on flotation response and, thus, help address some of the above questions. The focus of the studies was to optimize the metallurgical grade-recovery performance of the Cu-Mo separation plant at Teck’s Highland Valley Copper mine (HVC). The outcome was compelling and significantly valuable: consolidated production data showed that in 2008 – the year when the recommendations from the studies started to be implemented – the Mo plant recovery was 89%, and gradually increased to 92% and 94% in 2009 and 2010, respectively, along with an increase in Mo concentrate grade. (Note: these production figures were not included in the publications quoted above; however, they were shown during an oral presentation at the 43rd Annual Meeting of the Canadian Mineral Processors in 2011.)"

Jan 1, 2016

By J. M. Goris

"Researchers at the U.S. Bureau of Mines are conducting research on cable-type ground supports to assess their material and support properties and to provide design criteria for implementing cable supports as a workable roof control system under various underground mining conditions. Much of this work involves laboratory assessment of the material and support properties of cable supports using both conventional and birdcage steel cables. Included in this assessment are single and double cables, effects of changes in embedment length on support strengths, water-cement ratios, use of breather tubes, and pumpability and water-bleeding properties of grouts.IntroductionSince cable supports were introduced in the early 1970s, considerable research has been conducted in laboratories and at mine sites to understand their behaviour. The U.S. Bureau of Mines began a laboratory evaluation project in 1985 at the Spokane Research Center (SRC) to study the behaviour of cables supports under uniaxial loads so that the effects of various cable support components, such as grout and breather tubes, could be identified. Other objectives were to compare the behaviour of various types of cables and grouts and to collect meaningful data for numerical analyses. Pull tests were conducted to determine how cables supports reacted under uniaxial loads and how they failed when ultimate loads were exceeded. Such data are essential for the development of numerical models for analyzing rock mass behaviour when the rock is supported with cables.Test ProgramBecause each cable support can be composed of either single or double cables as well as a breather tube, pull tests were designed to include a variety of samples containing these components. A series of samples containing a single conventional cable, a neat cement grout having a water-cement ratio of 0.45, and no chemical additives was selected as a standard (Table I). Then one component in the system, such as the presence of a breather tube, was changed, and results of tests compared to results obtained for the standard samples to determine what influence that component might have on the behaviour of the support system. If significant changes in test data occurred, they could be attributed to that one component. To control the quality of the samples, the physical condition of the cables and tubes were monitored closely, and compressive and tensile strengths as well as flow properties were determined for the grout used in each test series."

Jan 1, 1991

By w. w. Fraser

"In late 1985, Hudson Bay Mining and Smelting Co., Limited announced the Namew Mine/Mill project. Environmental baseline monitoring and planning began in early 1985 while a major drilling program was under way to delineate the ore deposit. This paper overviews the environmental assessment work conducted for the mine/mill operation, and outlines the tailings and water management practices.Planned environmental works and approach were affected in late 1988 when a massive water problem was encountered in the mine. The requirement to depressurize the rock surrounding the underground workings led to the need to develop, on short notice, an environmentally-acceptable procedure to dispose of a large volume of slightly-saline water.Biological toxicity tests performed on the depressurized effluent proved the effluent to be non-toxic and thus allowed resolution of the disposal problem. This resolution includes the conversion of a large water body from native fish species to a rainbow trout fishery."

Jan 1, 1991