Search Documents

By Luis A. Infante

El texto señala la estructura de organización del departamento de Seguridad en la Southern Perú Ccoper Corporation, después de iniciado los trabajos de explotación y producción. El Departamento de Seguridad comprende tres secciones: la sección Seguridad de la mina, la sección Seguridad de la Concentradora, y la sección Seguridad del área de Ilo, donde se encuentra la Fundición. El departamento de Seguridad de la mina tiene por objetivo el el entrenamiento necesario a los supervisores y obreros con el fin de evitar accidentes. Como actividades complementarias a esta función, están las reuniones de seguridad que desarrollon los supervisores y las inspecciones de seguridad. El trabajo también describe el reglamento de seguridad de la empresa, el rol de los supervisores y capataces, el informe de accidentes y estadísticas, investigación de accidentes, los informes al Gobierno, el control de gases y polvo, las funciones del departamento contra incendios y la higiene industrial.

Aug 20, 1963

By AIME AIME

AT the annual .meeting of the Minnesota Section in December, Dr. Leith characterized as a question still open the exact method of origin of Lake Superior iron ores and emphasized it as an important practical problem for the future. He welcomed the step taken last year by Dr. Gruner in presenting a new hypothesis, and asked Lake Superior geologists to meet the challenge of such multiple hypotheses by unbiased, study.

Jan 1, 1932

By R. W. Fedors, S. T. Green, R. A. Hart, D. B. Walter

Computational fluid dynamic (CFD) modeling of a potential nuclear waste repository drift may be an important tool to estimate moisture redistribution caused by natural convection within the drift. To refine and support CFD techniques, a small laboratory cold-trap experiment was developed. Results from numerical modeling of the laboratory experiment show the sensitivity of the bulk air flow rate and average air temperature within the drift to several key parameters, including various boundary condition assumptions and surrounding porous media properties.

Jan 1, 2004

By Tom Treleaven

The success of any blast is dependent on the accuracy of the blast design and the field controls used on the shot. This point cannot be over emphasized because when the geometry is not measured and/or field controls are not properly implemented, it can often have devastating effects on the final blast results. Thus drilling accuracy, tiont row burden control, explosive confinement, energy distribution, explosive selection, timing and structural geology become critical parameters in the design of successful blasts. Understanding the actual dynamics of the blast and why certain results were achieved is the fast step in optimizing a blast design. As stated by R. Frank Chiappetta, “Of all the blast monitoring systems available today, high speed videography still remains as the best stand alone instrumentation system for blast diagnostics.” Over the past years I have analyzed hundreds of blasts using either high-speed lowcams (500 frames per second) cameras or standard digital (30 frames per second). These analyses confirm, without a doubt, that shot geometry, in combination with structural geology, is the most important factor in overall blast results. Drilling accuracy is the single most important component in efficient blasting. Having equal mass associated with an equivalent energy is the basis in which blasts are designed. When drilling inaccuracy or borehole deviation occurs, not only is the energy unevenly distributed, but the basis of all design calculations becomes invalid. Over the past several years, quarry and mining operations have employed the use of boretracking measuring devices to measure borehole deviation and hole toe locations. In cases of operations using top hammer drills, it was discovered that the amount of deviation was significant and far greater than they believed they had. Set up error, improper drilling techniques and bit wear were some of the contributing factors. Through video anaysis of boretracked blasts, blast results were directly linked to drilling ..accuracy. The comparisons here took into account blast design, energy factors and hole sequencing.

Jan 1, 2000

By Adrian Daniel

"Dating back to 1934, Con Mine is located directly south to the city of Yellowknife in the NWT, Canada. With mill operations ceasing in 2004, a challenging surface remediation situation resulted which required the treatment of close to 40,000 m3 of Arsenic impacted material.Through much of the period of 1941 to 1970, Con Mine treated their refractory arsenopyrite ore through the use of an Edwards Heath roaster. With mounting environmental pressure and through Canadian governmental studies during 1950 to 1970, attention was directed to the Arsenic Trioxide material being collected by two Doyle scrubbers on the Con’s roaster stack. In 1970, the roaster was decommissioned leaving the resulting Arsenic material in two containment areas on surface.As a result of Con Mine entering into remediation in 2004, the Con’s autoclave, commissioned in 1992, was dedicated to the immobilization of high impacted Arsenic material through the combination of excess Iron under high temperature and oxygen overpressure. Examined, herein, is the history and chemistry of the Con Mine autoclave as well as the two stages of chemistry for the Water Treatment Plant used to remove arsenic, heavy metals and WAD cyanide from tailings water. Simplified capping plans of the tailing containment areas and a high arsenic impacted area are also presented.INTRODUCTION TO CON MINECon Mine (Con) is situated just south of the City of Yellowknife in the North West Territories (NWT) Canada and is bounded locally by Yellowknife Bay (North Extension of Great Slave Lake) to the east and Kam Lake to the west (Figure 6). The discovery of gold at Con was made in 1934 and mineral rights were acquired by Consolidated Mining and Smelting Limited (Cominco) and Falconbridge soon thereafter. Nerco Minerals Limited (Nerco) took control in 1986 and in 1993, was subsequently sold to, Miramar Mining Corporation which in turn was purchased by friendly takeover involving Newmont Mining in November 2007 as a result of acquiring the Miramar’s Hope Bay project. Con’s underground operations ceased in September 2003 and have since entered into the remediation of the site. The current surface lease holdings are about 340 Hectares (Table 1) which sits on top of the Archean-aged Yellowknife Greenstone Belt."

Jan 1, 2009

By Júlia Guimarães Sanches

O curso de Engenharia de Minas sofreu uma expansão, juntamente com todo o ensino superior no país, por volta de 2005. O objetivo do presente estudo é avaliar as características dos cursos do país e realizar uma comparação com cursos de outros países com grande produção mineral. Foi feito um levantamento inicial a partir de informações disponíveis nos sites do MEC, INEP e das universidades. Como complemento, realizou-se um questionário com os coordenadores dos cursos de Engenharia de Minas do Brasil. Foram compilados ainda dados relativos à estrutura curricular e carga horária dos cursos de Engenharia de Minas dos EUA, Canadá, Austrália, Chile e África do Sul. Em relação à comparação das grades curriculares com os cursos de outros países, observou-se que no Brasil o curso possui uma maior cara horária de Tratamento de Minérios em detrimento da lavra. Nos demais países estudados, o foco das disciplinas é a lavra, já que nestes países a área de Tratamento de Minérios é assunto de outras Engenharias.

Oct 30, 2017

By Rosanna Ginocchio

Ante el aumento de los elementos inorgánicos y orgánicos en los suelos, aire y agua, se genera una preocupación mundial por los potenciales efectos negativos en el medio ambiente. Por tal motivo, se utilizaron métodos físicoquímicos como la vitrificación, electrocinética, y tratamientos químicos que son caros y relativamente agresivos. En ese sentido, el presente texto plantea la biorremediación como un método orgánico que utiliza las especies vegetales para remover contaminantes inorgánicos y orgánicos desde un sustrato sólidos para dejarlos in si tu en formas inocuas.

Sep 1, 2012

"Guideline Augered Cast-In-Place (ACIP) Pile Specification and Commentary11.0 GENERAL1.1 SCOPEThe Pile Contractor shall furnish all labor, materials, tools and equipment necessary for furnishing, installing and testing Augered Cast-in-Place (ACIP) piles as shown on the Contract Drawings and as specified herein.ACIP piles are commonly referred to by several other names. Some of them are trademarks or service marks owned by Foundation Contractors and some are names that try to describe the installation process. The term “cast-inplace” is sometimes replaced with “cast-in-situ,” especially in Europe. Some common names are Auger Cast Piles, Intruded Mortar Piles, Augerpress Piles, Augered Pressure Grouted Piles, AugerPile Foundations, Continuous Flight Auger (CFA) Piles, Grouted Bored Piles, Augered Grout-Injected Piles, Drilled or Augered Uncased Piles, and Uncased Cast-in-Place Concrete Piles. To avoid confusion, ACIP pile will be used exclusively herein.1.2 PILE CONTRACTOR QUALIFICATIONSThe ACIP piles shall be installed by an experienced Pile Contractor who upon request of the Engineer shall submit evidence of successful ACIP pile installation under similar job and subsurface conditions, including a job supervisor who shall have a minimum of five years of method specific experience.The proper installation of the ACIP piles is dependent upon the procedures used by the Pile Contractor’s field representatives and equipment provided. The Pile Contractor’s personnel responsible for the installation should have relevant experience with the auguring and pumping equipment, experience placing piles under similar site conditions (including restricted headroom if appropriate), in similar subsurface conditions, as well as experience handling the special grout mixes, admixtures, etc."

Jan 1, 2016

By María Quintana, Roger Veramendi, Gerald Salazar, Clemente Luyo, Noe Cabanillas

En este trabajo se presenta un sistema autónomo para remoción de plomo de efluentes mineros con monitoreo remoto, cuyo sistema opera a base de un novedoso material adsorbente, que se presenta en este estudio. Este material, obtenido a partir de arena y grafito, es estable, escalable, reproducible, biodegradable y se puede usar para el tratamiento de metales pesados en agua por medio de una red de filtros en boyas. El equipo desarrollado ha logrado remover casi el 99% a niveles de 10 ppm de contaminación de plomo en un rango amplio de niveles de pH, lo cual garantiza su correcto funcionamiento bajo condiciones de campo. Los componentes del sistema se basan en partes recicladas de otros equipos y utilizan energía solar para su funcionamiento continuo. Asimismo, el equipo contará con un sistema de monitoreo a control remoto, para que el usuario pueda registrar los niveles de plomo a la salida de la red de filtros.

Sep 20, 2019

For its Hellyer project, Aberfoyle sought to establish a high degree of confidence in all aspects of the feasibility study. Accurate capital and operating cost estimates were an integral and essential part of the study. They were crucial to the evaluation of investment returns and competitive cost position. Both the capital and operating cost estimates were based on the comprehensive data available from exploratory mine development, pilot plant operation, detailed engineering design, and Aberfoyle's experience in the area. One of the principal project objectives was to maximise operating productivity and efficiencies and this created capital cost alternatives which needed thorough cost-benefit assessment. The estimated capital cost for construction and development was $90 million, and the project was completed virtually on time for $80 million. The first year's experience indicated that operating costs would settle to well within 10% of the estimates.

Jan 1, 1990

At the Prospectors and Developers Annual Convention (PDAC) in Toronto, Canada mining and exploration companies of all sizes were on hand to discuss the year that was and those that will be. The following is a look at some of the companies with Canadian operations that were on hand for PDAC 2009. Iamgold Corporation is a leading mid-tier gold mining company producing approximately 31 t (1 million oz) of gold from seven mines on three continents. With record revenues of $870 million ? up 28 percent when compared to 2007 ? the company is focused on growth with a target to reach 56 t (1.8 million oz) gold production by 2012. During 2008, the company acquired the Essakane project in West Africa. The project is fully permitted, under construction and will contribute more than 9.3 t (300,000 oz) of lower cost production by late 2008. Iamgold increased its reserves by 55 percent, to 385 t (12.4 million oz) and its resources in-creased by 16 percent to 821 t (26.4 million oz) in 2008. Going forward, Iamgold has three areas of focus ? West Africa, Guyana Shield and Quebec ? with seven gold operations, five advanced projects and the Niobec niobium mine included. The Rosebel Mine in Suriname is Iamgold?s fl agship property. With measured and indicated resources of 300 t (9.6 million oz), it accounts for 30 percent of Iamgold?s production. Production there was up 20 percent compared with 2007 and further production increases are expected in 2009 and 2010. Mill expansion and optimization increased throughput from 8.9 Mt/a (9.8 million st) to 10 Mt/a (11 million stpy). In West Africa, Iamgold has joint ventures at Sadiola in Mali; Tarkwa in Ghana; Yatela in Mali and Daman in Ghana. Iamgold also has 100 percent ownership of the Mupane gold mine in Botswana and the Doyon gold mine in Quebec, Canada. Also in Quebec, Iamgold has 100 per-cent ownership of the Niobec niobium mine in Quebec. Niobium is used in high strength specialty steels.

Jan 1, 2009

By Brendan Henry

The Canada Line is a 19km long automated light rapid transit system with 16 stations in Vancouver, BC, Canada. The Concession was awarded to InTransitBC to design, build, partially finance, operate, and maintain the system for 35 years. The project must be complete by November 2009 to be ready for the 2010 Winter Olympics to be held in Vancouver and Whistler, BC. The bored tunnel section consists of 2.45 km of twin bored tunnel and 3 stations. The station work is limited to the excavations and temporary support necessary to facilitate the bored tunnel works. A joint venture between SNC-Lavalin Constructors Pacific and SELI (SSJV) has recently completed the design and construction of this section. Work for the bored tunnel commenced in November 2005 with shoring and excavation works for the tunnelling operations pit that will become Olympic Village Station and will be completed in the spring of 2008. The tunnels were driven with a 6m diameter Earth Pressure Balance Tunnel Boring Machine (EPBM) and lined with 250mm thick, 5.3m diameter precast concrete segments. Seven hundred and fifty meters of each tunnel were driven through glacial and interglacial deposits of sand, silt, and clay with granitic boulders. The paper discusses the challenges faced in negotiating these soils which contained unforeseen geological conditions. These conditions were overcome by developing a systematic approach to Risk Management that included thorough risk assessments, regular risk management meetings with the participation of two of the world?s leading EPBM experts, Professor Eisenstein and Professor Kovári, and by the ability of the construction team to effectively analyze and mitigate problems.

Jan 1, 2008

By Rommel Solís Salazar

El presente trabajo señala los beneficios del uso del inhibidor de incrustamiento para la extracción de oro y la plata. El inhibidor tiene la función de suprimir e inhibir la nucleación de cristales de carbonatos como un agente dispersante soluble en el agua, de forma que genera estadísticas de mejores ciclos de operación, reduce paradas por lavados, así como el empleo de ácidos fuertes adaptados de algunas otras industrias como la calderería y agricultura.

Jan 1, 2013

Alluvial gold grades are typically highly erratic. It is very often difficult to establish with confidence the in situ grades of reserve blocks due to the small number of pit or drill hole samples available, and their erratic values. Trends in grade are often obscure. Geostatical methods are inappropriate due to the extreme nugget effect found in alluvial gold field data. Classical statistics appear more suited to such data but require assumptions to be made regarding the nature of the population sampled. Recent developments in computer intensive non-parametric statistical methods provide a new approach to dealing with some of the above problems. These methods avoid making assumptions about the type of population distribution, usually through some kind of re-sampling scheme. The bootstrap procedure involves taking the estimate of interest and synthesising its population of by re-sampling the original data a large number of times (1000+), at random and with replacement. The synthetic population is then used to draw conclusions about the likely behaviour of the true population.

Jan 1, 1985

By Stephen A. Orr

Underground mining is a dynamic art and science with a diverse set of design, production, and economic criteria that must be considered before selecting an optimal method to extract the ore. While all methods can be technically classified as either self-supported, supported, or caving, the multitude of subsystems and existing variations bear witness to the fact that each orebody is unique and, as such, justifies an individual approach to optimize mineral extraction. In this sense, underground mining is an art. The ability to evaluate the unique characteristics of each ore body and utilize sound engineering principles to design the optimal system constitutes effective method selection. The task by no means ends at this juncture, however. Subsequent implementation requires an ability for modification. Very rarely are all the facts available to make a concrete decision prior to development of the resource. As a result, the risk of a wrong decision can never be eliminated. This requires a significant degree of flexibility with each method. Each unit of exploration, development, or exploitation work contributed to a deposit enhances knowledge of the ore body. The best mining methods are those that correctly account for the known parameters but provide an allowance for change at minimal cost and adapt to unanticipated conditions.

Jan 1, 2008

By Michael B. Gilbert

The Woodbury L-73 Tunnel involved the design and construction of a 96-inch tunnel driven through 8,080 lf of very difficult ground conditions. Anticipated ground and groundwater conditions consisted of potentially flowing silty sand with cobbles and boulders, mixed face of sand and sandstone and full face of the St. Peter Sandstone. Actual conditions were similar, although the quantities did change from bid quantities. This paper presents the approach used for development of the GBR regarding risk management. The means of arriving at a fair compensation for variances from the baseline values to address the actual encountered tunneling behavior of the soil, boulder count and its effect on production rates are presented.

Jan 1, 2008

By AIME AIME

NEW place was assigned to the women for their headquarters at the annual meeting of the Auxiliary but they, as usual, occupied a large place in the activities of the annual meeting. The alcove on the Thirty-ninth Street side of the building was a busy place on Monday morning, as the members of the various sections from New York to California greeted each other. The registration was conducted under the supervision of Mrs. Wolfes, Miss Georgene Davis and Mrs. Jennings, while Mrs. Hursh, Mrs. Hyde, Mrs. Charlton Reynders, and others dispensed tickets to the various functions that had been provided for entertainment. There seemed to be the usual number registered, but when only one member of the District of Columbia Section made herself known everyone wondered why the large delegation of last year had so dwindled. The explanation appeared next day, when a number of others from that Section arrived, telling of a delightful reception on the night before, at the White House. Mrs. Hoover had honored the "Canaries"¬(the organization of Lone Girl Scout' workers) the officers of the Section, and their husbands, who for once became only "so and so's husband." Luncheon was served on the fifth floor on Monday, the hostesses for that day being Mesdames C. F. Ayer, Willis Burns, G. W. Farny, H. G. Moulton, and T. T. Read. A number of sight-seeing trips had been arranged for the afternoon. The most popular proved to be an expedition to the new Riverside Church; where Dr. Fosdick is pastor. Guides were there to conduct

Jan 1, 1931

By R. Negrón

El presente trabajo describe la aplicación del proceso de lixiviación-cementización utilizado en la mina de Cerro de Pasco y en otros yacimientos de características similares. La aplicación tecnológica de la lixiviación subterránea data desde el año 1935, mientras que la lixiviación de las pilas del mineral en superficie y el proceso de cementación fueron implementados con ayuda de tecnologías análogas aplicadas en otras minas del mundo. En este sentido, si la particularidad de la lixiviación subterránea opera en áreas de explotación antigua donde las condiciones ambientales y de trabajo son bastante difíciles, impidiendo las operaciones normales que exige dicho procedimiento; el método de lixiviación-cementación en Cerro de Pasco permite recuperar una cantidad considerable de minerales de cobre dejados en el sub-suelo, de forma que se puede recuperar el contenido de cobre del mineral de pirita depositadas en pilas producto del desbroce del tajo abierto.

Nov 20, 1978

By José Beltrán

El monitoreo de condiciones es una herramienta importante en las operaciones mineras -en tanto asegura una buena salud de los equipos de producción. En ese sentido, el presente texto muestra los resultados de un equipo evaluador que opera el sistema de condiciones MineCare y valida distintos casos de análisis reales y cotidianos, verificando las ventajas de utilizar esta herramienta en ejemplos reales para las mejores prácticas operacionales dentro de la operación extractiva minera.

Mar 1, 2016

By T Higuchi, L Lu

The quality of iron ore fines have been deteriorating, which has affected sinter quality and productivity adversely. New pretreatment and sintering technologies are therefore required to tackle the gradual change in the quality of iron ore fines. In the sintering process, iron ore fines are first granulated with fluxes such as limestone and coke breeze, and are then loaded and fired in a sinter machine. Sinter productivity and quality are heavily influenced by the reactions occurring in the sintering bed. Hence fundamental understanding of these high temperature properties of ores is urgently needed.Formation of initial sinter melt, penetration and assimilation of nucleus particles by the initial melt, and consolidation and final solidification of final sinter melt are believed to be the key sintering reactions. The assimilation and penetration phenomena have been studied separately in the literature with model particles and diffusion couples and are therefore difficult to relate to sinter quality. In addition, the effect of ore mineralogy has not been studied in detail.In this study, tablets consisting of coarse particles from various iron ore fines as nucleus particles and chemical reagents as adhering fines were made and fired under various sintering conditions to investigate the penetration and assimilation behaviour simultaneously. The degree of assimilation, pore structure, compressive strength of the resultant analogue sinters were evaluated and the relationship between sinter strength and ore characteristics was further discussed. The nucleus particles from Ores A and B were found to be more porous and assimilated more readily with sinter melt, resulting in a viscous melt and a macro-porous sinter structure. The nucleus particles from Ores C and D on the other hand, assimilated less readily with sinter melt, resulting in a fluid melt and a denser sinter structure. This is consistent with the results reported in the literature, suggesting that the present evaluation method can be utilised for studying sintering reactions and predicting sinter quality.CITATION:Higuchi, T and Lu, L, 2017. Evaluation of sintering behaviour based on ore characteristics, in Proceedings Iron Ore 2017, pp 303–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017