Search Documents

The suitability of char from Yallourn brown coal as a filler for carbon electrodes used in the aluminium smelting industry has been assessed on the basis of the specifications usually laid down by electrode manufacturers for petroleum coke fillers. The purity specifications can be met by a simple acid leaching of the coal before carbonization. The true density of char produced at 1200°C is within 5 per cent of the specification figure, but the bulk density of char obtained from as-mined coal is only half that specified for petroleum coke.Although this can be increased to three-quarters of the specified figure by briquetting the coal before carbonization, further increases would be very difficult to achieve, as the remaining shortfall in density is due to an extensive microporosity developed in the particles of char during carbonization.

Jan 1, 1970

By M. P. Nesterov

The method of predicting the time-dependent surface subsidence for gently-inclined potash deposits where total extraction using various sizes of yielding bamier pillars was discussed.

Jan 1, 1998

By Sam Kangwa, Thomson Sinkala

In the mining industry, drilling accuracy has a significant effect on the economy of operations. In this paper, results from the Nkana Division of the former Zambia Consolidated Copper Mines are presented. For the stope investigated, it was found that the extra operational costs alone were 462% of the planned costs! Clearly, there is more than good reason to pay attention to drilling of good quality holes.

Jan 1, 2004

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By André Luis de Oliveira

O Alto Forno 3 (AF3) da Companhia Siderúrgica Nacional (CSN) é o equipamento muito importante no processo siderúrgico da Usina Presidente Vargas (UPV), situada em Volta Redonda (RJ), por responder por mais de 70% da produção de gusa da UPV. Na produção de gusa é gerado o Gás de Alto Forno (GAF), subproduto de alta relevância, pois este gás sai do topo do AF3 com grande pressão e cinética, energia essa passível de utilização. Em 2007 a CSN, optou por adquirir um equipamento denominado “Top Pressure Recovery Turbine” (TRT), capaz de aproveitar tal energia para gerar energia elétrica. Em 2013, a equipe de supervisores da KHI – Kawasaki Heavy Industrie, fabricante da turbina, veio para o Brasil para realizar no equipamento os testes a frio e a quente para na seqüência vir a operá-lo. Ocorre que fatores alheios ao objetivo desta apresentação impediram a equipe da KHI de partir o equipamento no tempo previsto, bem como de retornar ao Brasil para dar seqüência nas atividades. Em novembro de 2013 a CSN definiu por partir o equipamento com recursos próprios, sendo este o foco do trabalho. A presente contribuição técnica vem mostrar o trabalho desenvolvido internamente pelo grupo técnico a fim de finalizar o projeto e colocar a Turbina de Topo (TRT) em operação, fato este dado total ênfase pela direção da empresa devido ao cenário nacional de crise energética em que os valores de energia estavam no limite máximo permitido pela legislação e impactando diretamente nos custos da empresa.

Sep 25, 2017

By B. J. Breen, C. S. Mogg

Considerable borehole investigation work has been completed at a proposed site at Sellafield in Cumbria, supplemented by seismic surveys, other geophysical sensing and geological mapping. The focussing of investigation on the rock mass itself will be achieved by means of the planned underground rock characterisation facility, giving access to depths of about 800 m in the strong, low-permeability basement rocks of the Borrowdale Volcanic Group. Characterisation work undertaken during the sinking phase and interaction with continuing surface-based exploration and monitoring should permit a firmer assessment of the long-term safety of a repository. Key considerations in the choice of a design for the repository include the waste handling method, underground inlet cell, underground vaults, vault environment and environmental effects

Aug 1, 1994

By R. S. Dean

[Methods s of preparing the manganese metal that has been used in chemical and metallurgical investigations have passed through a cycle. Most of the investigations made e before the turn of the century, used Moissan's pyrophoric man manganese.3/ This material was made b; electrolysis into a mercury cathode and distillation in vacuo. The material was essentially pure, and investigations in which it was employed (with proper precautions against oxidation) led to accurate results on tie intrinsic behavior of metallic manganese.]

Jan 1, 1941

Wet mining of auriferous gravels at L & MÆs Waikaka operation in Southland creates spoil dumps derived from stripping of a clay rich overburden, tailings from past dredging and the processing of auriferous sands and gravels. Over recent times, spoil dumps have slumped on six occasions, threatening the viability of the wet mining operation. Close examination of slump morphology, coupled with the sequence of material placement and rate of dumping suggested a mechanism associated with undrained failure of a 2 m layer of silt and sand tails forming the base of dumps.Commencing with some information on the geotechnical properties of source overburden, back analysis of failure morphology and sequence and development of undrained loading conditions from first principals, the most likely failure mechanism and factors controlling failure were defined. Based on analysis results, a scheme to stabilise the lowwall dumps was developed and implemented, augmented by continuous monitoring of pore pressures in the basal wet tails, and laboratory testing for confirmation of computed material properties.Lowwall spoil stability has improved since implementation involving changes to the method of spoil loading, and modification of wet tails composition to improve permeability and drainage of the basal wet tails under load. The method and approach to prediction and verification of failure mechanism provide a sound basis for continued mining of deeper auriferous gravels.

Jan 1, 2002

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

The conventional rare earth element (REE) industry has historically sought to develop ore deposits where geologic processes have produced mineralized zones with commercially attractive REE concentrations. These deposits are extremely uncommon, particularly in the USA. Given the criticality of these materials and the need for sustainable domestic supply, the current research seeks to leverage other autogenous processes that lead to concentrated REE resources. One such process is the generation of acid mine drainage (AMD). AMD is very common in many coal mining districts and results from the exposure and oxidation of pyrite during mining. During the generation and migration of AMD, liberated sulfuric acid mobilizes several metal ions including REEs. Treatment of AMD is required under U.S.C §1251, the Clean Water Act, and often consists of neutralization, oxidation, and metal hydroxide precipitation. To investigate the deportment of REEs during this process, a field sampling campaign was undertaken, whereby the concentration of REEs in AMD and AMD precipitates was measured directly. In the nine sites evaluated in this study, the REE concentrations of the precipitates varied from 29 to 1286 ppm with an average of 517 ppm among the sampled sites. The individual elements were enriched compared with the associated bulk Northern Appalachian (NAPP) coal material by factors ranging from 3 to 15. Furthermore, the distribution of REEs in all precipitate samples favored the heavy REEs (HREEs) when compared with traditional REE ores. This research represents the first part of multi-part research endeavor to characterize, classify, and determine the practicality of refining REEs from AMD and its by-products.

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

The conventional rare earth element (REE) industry has historically sought to develop ore deposits where geologic processes have produced mineralized zones with commercially attractive REE concentrations. These deposits are extremely uncommon, particularly in the USA. Given the criticality of these materials and the need for sustainable domestic supply, the current research seeks to leverage other autogenous processes that lead to concentrated REE resources. One such process is the generation of acid mine drainage (AMD). AMD is very common in many coal mining districts and results from the exposure and oxidation of pyrite during mining. During the generation and migration of AMD, liberated sulfuric acid mobilizes several metal ions including REEs. Treatment of AMD is required under U.S.C §1251, the Clean Water Act, and often consists of neutralization, oxidation, and metal hydroxide precipitation. To investigate the deportment of REEs during this process, a field sampling campaign was undertaken, whereby the concentration of REEs in AMD and AMD precipitates was measured directly. In the nine sites evaluated in this study, the REE concentrations of the precipitates varied from 29 to 1286 ppm with an average of 517 ppm among the sampled sites. The individual elements were enriched compared with the associated bulk Northern Appalachian (NAPP) coal material by factors ranging from 3 to 15. Furthermore, the distribution of REEs in all precipitate samples favored the heavy REEs (HREEs) when compared with traditional REE ores. This research represents the first part of multi-part research endeavor to characterize, classify, and determine the practicality of refining REEs from AMD and its by-products.

By L C. Taylor, H U. Lesiste

This is a preliminary study of the statistical variation of the pressures on a target above a buried explosion. The data were taken at various distances from the charge centerline for three heights of the target above the soil and one charge depth of burial. All tests were conducted in saturated sand. They show that peak pressures and times of peaks are neither repeatable from shot to shot nor rotationally symmetric within a single shot. The peak pressure and time of peak at each location can be represented by cumulative normal distributions. The paper describes the means and standard deviations of these distributions at eight distances from the charge center for each height of target. These are used to determine the change in standard deviation of the distribution with distance from the charge centerline and height of target. The effect of scale on the mean peak pressures and times of peaks and on their standard deviations at a single scaled distance from the centerline of the charge are explored using various charge weights.

Jan 1, 2010

By S Hapugoda, J R. Manuel, M J. Peterson

Microindentation testing using the square–pyramid–shaped Vickers indenter is a well-established technique to determine the microhardness of minerals and materials. However there is a paucity of published microhardness data from Fe ore samples. It is acknowledged that an iron ore’s particle mineralogy and texture is critical to its processing properties, and it is therefore considered that the microhardness of different mineralogical/textural types may also relate to these properties. Mineral microhardness potentially provides inputs to the modelling of breakage characteristics during comminution, as well as the relationship between mineral chemistry and microhardness, and mineral microporosity and microhardness. Microhardness can be determined as single crystal microhardness, for more coarsely microcrystalline samples, or as ‘aggregate microhardness’ for cryptocrystalline or finely microcrystalline samples.Variations in the texture and mineral chemistry of common Fe ore minerals (eg martite and microplaty hematite, ochreous and vitreous goethite etc) are well established and this study provides microhardness data on different textural forms of Fe (oxyhydr)oxides from a variety of different Fe ore deposits. The data indicated that in general, the mineral grain size, microporosity and texture were the main influences on Fe (oxyhydr)oxide microhardness. There were no apparent systematic variations between microhardness and minor element mineral chemistry, with the possible exception of Al content in goethite (for goethites with Al content >0.5 wt per cent), and for goethite total element contents >90 wt per cent (determined by electron probe microanalysis, EPMA). Higher Al concentrations and lower total element concentrations in goethite EPMA analyses correlated with lower goethite microhardness. Microporosity and grain size were more important than texture to hematite microhardness. Different textural forms of dense hematite (eg martite, recrystallised interlocking hematite and specular hematite) with similar grain size exhibited comparable microhardness. Microhardness values for hematite and hydrohematite with little or no evident microporosity were also similar, whereas more porous forms of martite, microplaty hematite or hydrohematite exhibited lower microhardness.CITATION:Peterson, M J, Manuel, J R and Hapugoda, S, 2017. Microhardness testing of hematite-goethite Fe ores – implications for their textural characterisation and geometallurgy, in Proceedings Iron Ore 2017, pp 319–330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Kung-Lee Wang

This report describes the linkage of all mining sectors with all other manufacturing, services, and final demand sectors of the U.S. economy. Besides being a basic data source, it provides a framework for aggregate economic impact analysis with respect to the mining industries. The framework is an open-static input-output model specifying 48 mining industries as classified in the Standard Industrial Classification Manual for all mining activities and 76 nonmining industries which collectively exhaust, all economic activities. The 124-sector model used in this report is an expansion of the preliminary 82-industry aggregation estimates made by the Department of Commerce. In the expanded model, 48 ruining industries are substituted for the original 6. The methodology used to ascertain the industry-by-industry procurement cost estimates and product ion flows necessary to the construction and expansion of the basic 82-sector model included personal interviews, case studies of specific mining activity analysis, and published and unpublished data from the Bureau of Mines and the Census of Mineral Industries, The end products of this study are two tables arranged to show the direct purchases necessary for each industry to support the level of economic activity and the total purchases generated in each industry throughout the economy by each $1 of aggregate economic demand in 1958. The tables may he used for economic impact studies and market analysis by firms engaged in or closely associated with the mining industries. Some illustrations of their usages are presented.

Jan 1, 1967

Performance of Dry Separation Processes in Cenospheres Recovery from Coal Fly Ash

Sep 13, 2010

By Y. Zhoa

The surface morphology of materials is of fundamental importance to many surface related applications, such as wetting, friction, reflection, drag, and adhesion. Various approaches for micro/nano patterning atop polymer surfaces have been proposed in recent years. However, a cost effective technique is still highly in demand. In this paper, we demonstrate a novel but rather simple and generic approach for surface micro/nano patterning using shape memory polymers (SMPs). Different types of novel patterns are realized and their 3-D surface features are quantitatively analyzed by a PLµ Confocal imaging profiler.

Jan 1, 2010

By Daniel W. H. Su

The importance of incorporating fundamental principles of rock material response and failure mechanics into a pillar strength design model has been demonstrated. To accurately assess pillar strength, a model should account not only for the characteristics of the coal, but also for those of the surrounding strata. The interactions between the pillar and the surrounding roof and floor dictate ultimate pillar strength. Confinement, or the lack thereof, provided by roof and floor frictional end-constraint is one of the most significant factors in the strength of very wide pillars. The best conditions for end-constraint occur with ideally strong roof and floor. In this paper, it will be shown that weak roof and floor may decrease the ultimate pillar strength by as much as 30% compared to ideal conditions. Field observations confirm this pillar strength reduction in the presence of weak roof and floor. Furthermore, rock partings within the coal have a variable effect on pillar strength, depending on the parting strength. A competent shale parting within the coal reduces the effective pillar height, thus increasing the ultimate pillar strength; a weak claystone parting slightly decreases the strength. Imposed load distribution also has a significant effect on pillar strength, such that asymmetric pillar loading, similar to that observed in pillars adjacent to high extraction mining, reduces the ultimate pillar strength below that of equivalent pillars subject to uniform load distributions.

Jan 1, 1997

By Frank A. Peters

This evaluation of the sulfurous acid process for the production of metallurgical-grade alumina is the first of a series concerning various known methods of extracting alumina from low-grade aluminous materials and was undertaken to permit comparison with other processes. In the process with which this Bureau of Mines report is concerned, calcined clay is leached under pressure with 20 percent sulfurous acid and then filtered to remove a siliceous residue. The aluminum sulfite remaining in the filtrate is precipitated as a monobasic sulfite which, together with iron sulfite, is then decomposed under pressure to form a crude alumina hydrate and iron oxide. This intermediate product is purified in a modified Bayer process to yield alumina suitable for electrolytic reduction to aluminum. A study estimate (16)3 is used for these evaluations. The capital cost, not including land, is estimated at $95,701,600 on a Marshall and Stevens index basis of 240.0 for a plant producing 1,000 tons a day of alumina or 350,000 tons a year. The annual operating cost for this size plant is estimated at $22,831,100 or $65.23 per ton of alumina using clay at $1 per ton. Depreciation and local taxes are included in the estimate, but profit and Federal taxes are not considered.

Jan 1, 1962

By Robert E. Barieau

A list of 163 references to original experimental PVT data on helium is presented for the period 1895 to 1968. The list is complete as of the start of the Helium Centennial Year, 1968, to the best of the author's knowledge. Citations were keypunched for easy updating and are listed alphabetically by author.

Jan 1, 1968

By G. Couture

"The Glencore Raglan mine Concentrator, located in Quebec’s Nunavik region, has been in operation since 1997. The nickel metallurgical plant was originally designed to process 100 tonnes per hour of ore to produce 130 000 tonnes of nickel concentrate per year at 16% Ni. The increased grinding capacity and the discovery of rich ore bodies have increased the annual production to more than 190 000 tonnes of concentrate at 19% Ni. In 2014, the Metallurgical group, with support from BBA, implemented an expert control system on the flotation circuit. This project was initiated to cope with the high variability of the concentrator’s feed. Increasing the plant recovery and final concentrate grade were also important project objectives. The implementation of the expert system ensures better control of concentrate inventory while maintaining maximum plant throughput. This paper describes the successful implementation of the new control system, the control technology selection and the flotation circuit optimization. It will also discuss the performances obtained with this new approach and the improved process stability.IntroductionThe Raglan Mine is located in Northern Quebec along the 62th parallel. It has been in operation since 1997 and was originally designed to produce 130 000 tonnes of concentrate annually at 16% Ni. The increasing of the grinding capacity and the discovery of rich ore bodies have increased the annual production to more than 190 000 tonnes of concentrate between 18 and 20% Ni."

Jan 1, 2015

By Richard J. Mainiero, Michael J. Sapko, James H. Rowland III, Marcia L. Harris

All explosive materials produce a cloud of reaction products, the most toxic of which is nitrogen dioxide (NO2). In the study reported here, 4.5-kg (10-lb) charges of blasting agent confined in either thin-wall 10-cm (4-in) diameter galvanized pipe or 10-cm (4-in) schedule 80 seamless steel pipe were detonated in a closed chamber. The detonation gases were analyzed for NO2, nitric oxide (NO), ammonia (NH3), hydrogen (H2), carbon monoxide (CO), carbon dioxide (CO2), nitrogen (N2), oxygen (O2), and methane (CH4). Data were evaluated to determine the kinetics of the oxidation of NO to NO2. Analysis revealed that the only mechanism for NO loss for the conditions existing in the chamber was the reaction 2NO + O2 6 2 NO2. The rate constant was 2.08 @ 10-38 cm6 molecules-2 sec-1 for the rate equation -½d [NO]/dt = K @ [NO]2 @ [O2] for NO concentrations up to 100 ppm. The rate constant is in agreement with that recommended by Baulch, Drysdale, and Horne (1973).