Search Documents

By Irajá Bernardino Ribeiro Juniorr

O presente trabalho tem por objetivo apresentar alguns exemplos de aplicações na Indústria Siderúrgica e de Mineração (Prensa de Rolos e Torre de Resfriamento) mostrando que com o emprego de uma confiável metodologia para determinação dos benefícios energéticos é possível a implantação das medidas de conservação de energia em sistemas de força motriz instalados nestas indústrias com o simples uso de Lubrificantes Sintéticos Especiais em substituição ao largo emprego de óleos minerais. Esta solução também proporciona ganhos energéticos e financeiros expressivos e mais atrativos do que as já consagradas soluções de eficiência energética como troca de lâmpadas e /ou motores de alto rendimento. Além do mais, a troca de lubrificante já é rotina implementada nas indústrias e seus profissionais da área de manutenção, não sendo preciso treinamento adicional para implementação, tornando esta ação com o propósito de economizar energia simples e fácil de ser implementada. Este trabalho é uma parte dos resultados do projeto inovador desenvolvido pela Klüber Lubrication desde 2010, onde o principal objetivo é disponibilizar aos usuários de sua linha de produtos este recurso, internacionalmente reconhecido, de Medição & Verificação para a comprovação de ganhos de energia em prensas de rolos com alcance de redução de cerca de 10% de consumo de energia.

Aug 17, 2017

By Mohammed Sakr

A Two-Section Helical Pile (TSHP) is a steel pipe with two shaft sections of different diameters and with one or more helix plates near the bottom of each shaft section. TSHPs are used regularly in western Canada as foundation pockets for single and double circuit distribution power line poles. The results of a comprehensive lateral pile load test program and the field monitoring of TSHPs installed in organic soil (muskeg) over soft clay are presented in this paper. A total of nine full scale lateral load tests were carried out, including seven tests using TSHPs with different diameters and embedment depths, and two tests using one-section helical piles. The prime objective of the study was to evaluate the lateral resistance of TSHPs installed into very soft organic soil (muskeg) overlying soft clay soils, to compare their lateral resistance relative to one-section helical piles and to compare the measured and the estimated lateral resistances using p-y curves. In order to provide sufficient soil data for analysis, the subsurface soil stratification was evaluated using two different techniques including; Cone Penetration Tests (CPT) and Portable Soil Probe Tests (PSPT). The two testing techniques were also compared and evaluated. This paper summarizes subsurface soil conditions, pile configuration, helical pile installation procedure, testing setup and results.

Jan 1, 2009

By Bradford F. Townsend, Marc R. Kritzer, Michael F. Roach, Dennis Ofiara

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistance of an appropriate professional should be sought. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of the authors and are not necessarily those of SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2008

By Edwan Anderson Ariza Echeverri

O aumento das exigências para reduzir o consumo de combustível e aumentar a segurança dos passageiros tem estimulado o desenvolvimento da nova geração de aços de alta resistência. Esses objetivos tornam-se atingíveis com a redução do peso dos componentes de aço do veiculo, pelo uso de chapas mais finas e resistentes, mas não menos dúcteis. Com esse propósito, no presente trabalho pretendeu-se analisar os efeitos de diferentes rotas de processamento: estampagem a quente, têmpera e partição e o inovador processo que combina a deformação a quente com a têmpera e partição. Os ciclos térmicos foram projetados para obter a maior fração de austenita retida, além de ferrita e martensita. Para cada amostra tratada, amostras de tração de tamanho reduzido foram extraídas de amostras previamente tratadas em simulador termomecânico avançado Gleeble 3S50. A microestrutura foi analisada por microscopia óptica e eletrônica de varredura. Com o novo processo combinado acredita-se que seja possível atingir uma boa associação de propriedades para a nova geração de aços de alta resistência pela transformação da austenita retida metaestável em martensita induzida por deformação, contribuindo para a absorção de energia durante impacto.

Aug 16, 2017

By M. D. Balen

The U. S. Bureau of Mines has undertaken the development of mineral industry cost escalation factors to enable the estimation of mineral development and extraction costs for mineralized sites in Alaska throught the use of the Bureau's Cost Estimating System v2.0 (CES 2.0). For the purposes of this document, all calculations are based on, and reflect the economic environment in Alaska in July 1992. The greater cost of mining in Alaska as compared to the contiguous-48 States can be estimated for Alaskan mining operations through (1 ) the analysis of capital and operating costs for analogous mine and mill plants in operation in the contiguous-48 States; (2) the hypothetical relocation of mine and mill plants from their actual location(s) to Alaska by making engineering modifications to the mine and mill plant design as required by the Alaskan site characteristics; (3) calculation of the cost of the required engineering modifications and; (4) the escalation of all costs to a level representative of the economic environment in Alaska at some specific point in time.

Jan 1, 2011

By Floyd Varley

In deep and highly-stressed coal mining, advanced design practices are used to minimize the potential for damaging events to occur. Despite these design efforts, the hazard of coal mine bumps can not be completely eliminated. This paper will review current and historic work practices used internationally to minimize the hazard to miners from mining in conditions which could produce a bump. These site specific work practices have a common base in monitoring for conditions which could result in a bump and application of controls to prevent the occurrence or minimize the severity of an event where miners are working. Monitoring practices range from purely observational to semi quantitative. Control methods attempt to initiate events in a controlled manner, absorb the energy of a potential event or reduce the potential for or magnitude of an event by altering the stress conditions of the mine workings. Building from the experiences of other coal fields, an empirical framework to manage the potential hazard of coal mine bumps can be developed to enhance the level of safety provided by prudent mine design.

Jan 1, 2008

A large body of porphyry-type copper mineralization occurs at Panguna in southern BougainviIle. It is associated with the intrusion of quartz diorite/granodiorite into andesites, particularly with the contact zone. Metasomatism of both intrusives and andesite resulted in the formation of biotite pseudomorphing hornblende and the veining of the resultant biotite diorite and biotitized andesite by quartz-chalcopyrite veins with pink orthoclase and dark biotite selvages, respectively.The orientation of intrusives and veins appears to be controlled by premineralization fault-joint patterns in the intruded andesitic Kieta Volcanics.

Jan 1, 1968

By E. E. Krist

El desmuestre de un criadero tiene un buen número de finalidades. En la fase inicial es necesario definir los límites del yacimiento y el contenido o ley del mineral hasta el punto de que pueda ser establecido si es, de hecho, un yacimiento económico. Igualmente, las muestras tienen que ser generadas de forma tal que las evaluaciones geológicas y metalúrgicas puedan ser Ilevadas a cabo. Finalmente, cuando se conoce la suficiente información concerniente a la geología, mineralogía y metalurgia, puede ser desarrollado un método minero y su plan, y construidas las oportunas plantas metalúrgicas para procesar los minerales a medida que se encuentran disponibles1. Con las minas actuales grandes y complejas a cielo abierto los métodos de desmuestre único deberían de ser inadecuados. La perforación por diamante, la perforación por percusión, pozos subterráneos y galerías, juegan todos conjuntamente un papel parcial en la definición total del yacimiento. En la mina Twin Buttes, de la Anamax Mining Company, el desmuestre y la definición del yacimiento conducirán eventualmente a la existencia de tres plantas metalúrgicas de proceso y, quizá a, una operación de minería subterránea. Fue puesto en marcha un concentrador de sulfuros de 30.000 tons. por día en Septiembre de 1969 y una planta de 10.000 toneladas diarias de lixiviación de óxido fue puesta en servicio en Mayo de 1975. La finalidad de esta presentación es la de exponer históricamente el desmuestre del yacimiento que ha sido Ilevado a cabo en Twin Buttes, describir brevemente el criadero, y exponer los métodos analíticos corrientemente utilizados para ayudar al geólogo, al metalúrgico y al diseñador de la mina en sus respectivas evaluaciones.

Jan 1, 1982

By Marcelo Marchesi Martinelli, Caio Henrique Vidigal

Gasômetros são equipamentos de grande valia para aumento da eficiência energética e ambiental de empresas siderúrgicas integradas, sendo estes equipamentos responsáveis pelo controle da pressão do gás resultante das transformações dos processos siderúrgicos, controle este realizado através das variações de volume abaixo dos pistões. Quando não há disponibilidade de operação dos gasômetros faz-se necessário o uso de torres de queima para controle das pressões das redes de gases. Em dezembro de dois mil e dezoito fora realizada a troca da selagem do gasômetro de gás de Coqueria da ArcelorMittal Tubarão, que utiliza a tecnologia M.A.N. (Selo a óleo). Utilizando técnicas da metodologia Lean, modificando o mindset e alterando antigos paradigmas foi possível realizar a manutenção, de forma eficaz, em 32 dias, 28 a menos que o último trabalho similar realizado e 13 dias a menos que a meta proposta para a parada, aumentando a recuperação de gás de Coqueria, maximizando ganhos de geração elétrica e minimizando a exposição a riscos ambientais associados a parada. As ideias apresentadas neste artigo são de grande valia para a evolução do pensamento crítico e sistêmico sobre a manutenção, não só em gasômetros, mas em todo o contexto de realização de atividades já consolidadas.

Aug 1, 2019

By Yang Ge, Yuzhu Pan, Mansheng Chu, Jue Tang, Cong Feng, Lihua Gao, Zhenggen Liu

The low-grade nickel laterite ore used in this study was successfully upgraded through selective reduction by industrialized rotary kilns followed by magnetic separation. The results indicated that both iron metallization extent and nickel metallization extent showed obvious linear correlation. In addition, rational roasting temperature and prolonged grinding time could enhance the overall fineness level of reduced laterite nickel ore. The moderate roasting temperature at a range of 1100–1150 °C should be suitable enough to a conversion of total nickel to metallic nickel and partly inhibited the conversion of total iron. Ultimately, the obtained ferronickel alloy with a nickel content of 7.32% and an iron content of 84.15% was prepared successfully from the lowgrade nickel laterite ore containing a nickel content of 1.92%. Nickel and iron recoveries were 96.72 and 89.08% respectively, which achieved the highly efficient recovery and utilization of iron and nickel from low-grade laterite nickel ore

By Robert E. McIvor

The Functional Performance Equation for Ball Milling” was first presented in 1988. It now has been used successfully in more than a dozen mineral processing plants. This powerful, yet simple tool provides a new level of understanding of closed circuit grinding. It shows how grinding circuit efficiency is in reality comprised of two distinct efficiencies. It demonstrates how circuit production rate is related, collectively, to these two efficiencies, mill energy input, and the grindability of the ore. It links circuit performance to design and operating variables that can be manipulated, and creates an effective strategy for making plant improvements. This paper covers the derivation and industrial validation of this equation. As part of an engineering and management system that also incorporates suitable metrics and process control, other operators can now use this tool to make improvements and to manage the performance of their grinding operations with clarity and confidence.

Jan 1, 2005

By Linge HG, Fernandez PG, Hughes HC

Aqueous oxidation is a possible alternative to roasting for the processing of gold bearing arsenopyrite (FeAsS) concentrates. The reaction has been studied by voltammetry and this has shown, for the first time, that FeAsS can be readily dissolved without passivation at room temperature in dilute sulphuric acid at relatively modest oxidation potentials (0.7 V SHE). The reaction forms sulphur on the mineral surface and the oxidant consumption is thus minimal. Two practical modes of slurry oxidation are listed.

Jan 1, 1989

By David V. Lewin

Heavy structures in central Cleveland, Ohio, are supported on raft foundations, driven piles, or caissons. Settlements can be predicted and structures are designed to accommodate such settlements. On one project the settlements were not provided for in the design of the structure. Soils are sands, silts, and varved clays to shale. A rift in a central area is 600 feet deep. Solutions to problems, and results, are detailed.

Jan 1, 1985

A poured slag bottom is universally considered to be the best type bottom for copper reverberatory furnaces. It is impervious to molten matte and ready for immediate use.When molten slag is not available a monolithic silica bottom is the second best; such a bottom has been adopted at Mount Morgan. The laying of such a bottom is a phase of smelter construction on which so little real information is obtainable that a day to day record of such a recent example as Mt. Morgan's 19 ft. x 40 ft. reverberatory may be of interest. The work was done under the direction of E. Pesout, of McGill Smelter, Nevada. PREPARATION OF THE BOTTOMA 26-inch bed of closely packed firebrick with sand-filled joints was first laid on the clean, dry concrete foundation and the whole dried out by small fires maintained on the brickwork for several days. Ninety tons of silica sand was meantime thoroughly dried and stored in clean drums. This sand must be low in FeO and CaO and contain about 95% Si02 , the majority of which should be present as tridymite. This form of silica shows little expansion at high temperatures, for it is the form stable between 870° and 1470° C.Its presence thus minimises disturbance to the bottom by the expansion which, during the burning in, would mark the transformation of quartz to tridymite.

Jan 1, 1939

By Héctor Benavente Revilla

El presente texto señala la ubicación y acceso, reseña histórica, geología general y operación del yacimiento aurífero San Antonio de Poto, provincia de Sandia, distrito Ananea, ubicado en el departamento de Puno.

Mar 1, 1978

By Eric H. Brown

One of the best methods by which the results of accident-prevention work can be measured for any particular period is to keep an accurate record of the accident experience, which may then also be compared with the experience of others. The purpose of this report is to compare records of the salt-mining companies operating in Louisiana, and their assistance in making available their accident records is gratefully acknowledged. PRODUCTION Four companies produce salt in Louisiana -Avery Salt Co., Avery Island; Jefferson Island Salt Mining Co., Jefferson Island; Myles Salt Co., Weeks; and Carey Salt Co., Winnfield. Three of these companies operate within 30 miles of each other in the southern part of the State, and the other operates in the central part.

Jan 1, 1938

By Irving Hartmann

Falls of roof in coal mines and means of preventing them have been subjects of study for many years, and ran extensive literature has resulted, Usually each individual paper has placed 'emphasis on one phase of the subject, such as fatalities, nature and extent of nonfatal injuries, methods of tembering (particularly in rooms or other wide places), safety along retreating rib lines, and methods of causing falls in abandoned areas. It is only in recent years that there has been persistent question as to why

Jan 1, 1941

By Michael E. Berndt

Asbestos first became an issue to Minnesota?s iron industry when it was revealed that mineral fibers similar to those in Reserve Mining?s tailings were being found in drinking water for several communities that used Lake Superior as their primary water source. This discovery turned what had largely been an environmental court battle into a case concerning public health. The courts listened to much conflicting and uncertain scientific testimony on the size and distribution of the mineral fibers and on the potential health effects imposed by them. In April 1974, the plant was ordered to shut down by a federal judge but the company quickly appealed the decision. The appeals court granted a stay and ultimately ruled that the plant?s closure could not be justified based on the unknown health effects of the mineral fibers since the consequences of such an action would have immediate and severe social and economic impacts. The plant was allowed to continue operation, but ordered to abate emissions to air around the plant and to switch to a land-based tailings disposal system. Much of the scientific uncertainty and public concern over mineral fibers in Minnesota?s taconite industry remain today. ©2007 Elsevier Inc. All rights reserved. Keywords: Minnesota; Iron ore; Taconite; Asbestos; Amphibole; Reserve Mining; Tailings; Mesabi Iron Range

Jan 1, 2007

By R. S. Dean

In addition to the normal work and that pertaining to strategic minerals, the Metallurgical Division has been made responsible for carrying on major investigations in the development of processes' for the treatment of low-grade domestic manganese ores that heretofore have failed to yield products suitable for the preparation of ferromanganese, an alloy essential to every ton of steel produced. These investigations are particularly important at this time because of their part in tucking this country self-sufficient with regard to manganese when the stock-piled ore becomes e exhausted and as foreign shipments of ferro-grade ore are cut off. The results indicate that there is a good probability of accomplishing this objective, while at the same time conservation may be promoted through the use of normally useless material from the large, low-grade ore deposits.

Jan 1, 1941

By Christophe Bragard

The Los Angeles Metro Eastside Extension light rail project included a 1.5 mile underground segment, which consisted of twin 18'?10" ID tunnels, bored with two EPB-TBMs. One of the major project challenges after the completion of the bored tunnels was the excavation of six cross passages within alluvial geology below the water table and with low ground cover. Sequential excavation methods were employed and this paper details the design, ground treatment, support measures, and construction methods used to mine these cross passages beneath the congested urban streets of the City of Los Angeles.

Jan 1, 2008