Search Documents

By K. Narayana Swamy

Experimental results of 3-phase mixing in a physical model of a CCRL for metals refining, at high levels of bottom gas injection (up to a superfIcial gas velocity (Us) of 12.5 cm/min), are presented. A thermal tracer technique was used to elucidate both longitudinal mixing and interphase heat transfer. The results indicate that even under conditions of significant bottom gas injection, it should be possible to maintain acceptably low longitudinal mixing (D. < 20 cm2/s and D/uL < 0.1) in the CCRL. Interphase mass-transfer coefficients of the order of 0.02 cm/s and higher, are predicted from the measured interphase heat transfer coefficients using the mass and heat transfer analogy. Adequate performance is likely to be possible for an industrial CCRL, based on extrapolation of these results to full-scale conditions.

Jan 1, 1996

Sanes are utilized to make molds for metal castings in the foundry industry. Approximately a half ton of sand is disposed of for each ton of metal cast in this country. The purpose of this investigation was to study and develop a process to separate chromite sand and silica sand from reclaimed sands for a steel foundry. Physical separations were utilized to yield silica and chromite sands with desirable molding properties. Several different separation methods, including electrostatic, magnetic, and various gravitational approaches were examined. Experimental results are presented. A method was developed to separate chromite sand from silica sand after mechanical or thermal reclamation. The reclaimed sands are passed through a rare earth magnetic separator to separate chromite sand and magnetic impurities from non-magnetic silica sand. Chromite sand can be recovered from magnetic silica sand or magnetic impurities very effectively using a wet concentrating table. The applicabilities of the separation methods are discussed.

Jan 1, 1995

By D. M. Hausen

It has been demonstrated that microscopic techniques can be applied in a practical manner to the study of spodumene liberation in the processing of pegmatitic ores at the Kings Mountain spodumene plant, Kings Mountain, North Carolina. Spodumene and associated non-opaque gangue minerals are identified and quantified by microscopic point-counting of polished thin sections of heads, concentrates, middlings and tails fractions. Specially prepared polished thin sections? provide uniform thickness of particles for measurement of diagnostic optical properties and the alternate use of incident and transmitted light in distinguishing the various gangue and ore minerals. Spodumene is commonly associated and interlocked with quartz, albite, microcline and muscovite. Concentrate grade depends on the degree of spodumene liberation, which in turn depends on the crystal size and textural association of interlocked minerals. The liberation of spodumene can be measured as a function of screen size by means of microscopic point-count data. Microscopic data also provide useful metallurgical information about the nature of diluent minerals in spodumene concentrates, and the form of lithia losses in the tails. Lithium assays correlate closely with microscopic spodumene analyses in various flotation products from Foote Mineral&apos;s Kings Mountain plant, and confirm the applicability of quantitative optical microscopy to the study of liberation and recovery of spodumene from pegmatitic ores. A better understanding of recovery-grade relationships was developed as a result of quantitative microscopy studies.

Jan 1, 1981

By John J. Dunkley

Recent years have seen the increased use of hydrometallurgy in the smelting and refining of metals. However this is often used as a final refining step, following an initial pyrometallurgical smelting process. Huge amounts of material are produced as melts which have to be cast, comminuted, and taken up into solution or leached. A common method is to granulate the melt and then grind it. In the case of metallic melts this can be difficult or unfeasible due to the ductility of the granulated particles. Water atomisation is capable of replacing the granulation and grinding stages with a single process step that can process in excess of 30t/hour of melt into particles as fine as 50 microns. Applications in operation in Co, Cu, Ni, Ag, Au, Pt and Rh refining are discussed together with potential applications in copper smelting.

Jan 1, 2003

By S. Z. El-Tawil, K. A. El-Barawy, M. B. Morsi, M. M. Nasr, Z. I. Zaki

"Tue sulphatization of zinc concentrate produced from heated zinc concentrate of Um Ghieg area, eastern desert by ammonium sulphate as sulphatizing agent is carried out at different conditions to achieve the appreciable formation of soluble sulphates. The maximum zinc recovery as soluble sulphate equfils to 95% upon using 1.5 stoichiometry ammonium sulphate at 600 °C for one hour. Tue obtained leached zinc sulphate solution is subjected· to purification process to prepare high pure zinc metal and zmc compounds such as pure zinc sulphate, zinc caibonate and zinc oxide. The products obtained are analyzed chemically and identified by X-ray analysisTue mechanism and kinetics of the sulphatization process of zinc concentrate are considered where the activation energy is calculated and equals to 33.3 K.J.mol""1 A process flowsheet for the overall sulphatization process of zinc concentrate by ammonium sulphate is proposed.IntroductionConsiderable reserves of zinc ores are present in Um Ghieg area eastern desert, Egypt. The possibility of extraction zinc from these ores and preparing its valuable compounds by choosing a more feasible technology become of vital importance. An attention is focused on the sulphatizing roasting processes (1-9) to achieve the appreciable formation of soluble sulphates. Previous publications are reported in our division by El. Tawil and others (10-16) using ammonium sulphate as sulphatizing agent for the successful treatment of nonferrous bearing materials.Therefore, the present work aims to study the different factors affecting the sulphatizing roasting process of local zinc coocentrate by anunonium sulphate to extract completely zinc and preparing its main compounds. Tue mechanism and kinetics of the different chemical reactloos that 1ake place in the process are considered."

Jan 1, 2000

By M. Kobashi, T. Choh, N. Kanetake

"A new processing route, which enables the cost-effective and energy- saving fabrication of metal matrix composites, have been proposed. The pressureless infiltration of the reactive powder blend with molten aluminum was investigated in this work. The molten aluminum infiltrated into the [Ti + C] powder blend spontaneously, whereas the spontaneous infiltration into the TIC powder phase did not occur under the same experimental condition. The processing time was shortened and· the processing temperature was .lowered by adding the aluminum powder in the [Ti + C] powder. The differential thermal analysis revealed that the aluminum powder in the powder blend melted at 933K and then ignited the reaction between titanium and ·carbon. However there was an .optimum additional amount of aluminum in the powder blend. The TiC formed in situ had three-dimensionally continuous morphologyIntroductionThe squeeze casting process has been used as one of the processing routes for aluminum matrix composites. [1, 2]. Non-reactive metal-ceramic systems have been, generally, used in this technique in order to prevent the degradation of the ceramic phase. Materials obtained by this process basically consist of a continuous metal matrix and discontinuously dispersed ceramic particles. Reactive systems have begun to be introduced into the infiltration process· recently [3A]. Since the ceramics are synthesized in-situ, this process can provide a continuous ceramic matrix [5]. This is one of the outstanding features of this technique in that a bulk ceramic-can be synthesized at relatively lower temperatures in a short time. Another advantage is that the highly reactive combination of a ceramic with a molten metal is in many cases wettable [6], which enables a spontaneous infiltration."

Jan 1, 2000

By D. M. Fermino, C. G. Bastos Andrade, V. F. Justo, F. R. Valenzuela-Diaz, M. G. S. Valenzuela, C. Volzone

The present paper presents the study of light green smectite clay, from Paraiba, Brazil, submitted to mild acid attack under moderated conditions. Usually, clays are subjected to treatment with strong inorganic acids at temperatures near the boiling point and at high acid concentrations and then, widely used as bleaching agents. The treatment occurred under bellow boiling temperature and at short times of reaction (90°C, reaction times of 1, 6, 12, 18 and 24 hours in close reactor, concentration of the aqueous solution of hydrochloric acid 1.5 M, clay/acid solution ratio of 1g/10mL). The purpose of these attacks is to reduce the concentration of impurities providing color, with minimal change in the clay minerals structure, aiming at use in products of high value such as cosmetics and polymer/clay nanocomposites. The raw clay and the attacked samples were characterized by X-ray diffraction (XRD), cation exchange capacity (CEC), stereomicroscopy, scanning electron microscopy (SEM) and energy dispersive X-ray detector (EDS).

Jan 1, 2015

By Sui Xue

A process has been developed from laboratory-scale experiments for the aqueous processing of various lead-bearing wastes. The process exploits the limited solubility of lead in sulfate-rich solutions to effectively separate lead from other metals. The lead sulfate is then completely converted to lead carbonate using sodium carbonate and ammonium carbonate. The effectiveness of this conversion was observed to be sensitive to the solution pH and carbonate concentration. The final stage of the process uses low temperature calcination of the lead carbonate to form PbO. Yellow lead oxide (massicot) is readily formed if calcination is conducted at a temperature at or iibove 50G°C, wlule red iead oxide (iitharge) is formed at temperatures near 450°?C. A complete economical analysis of the process will be discussed.

Jan 1, 1996

By Takaaki Shibata

The Tamano Refinery has developed two new processes for removing the impurities, arsenic, antimony, and bismuth from an electrolyte. The first process involves bleeding the surface electrolyte in the electro-refining cells. The copper concentration level in the outermost layer is lower than that in any of the other layers, while the impurity levels are almost the same in all layers. Bleeding the surface electrolyte increases the amount of impurities removed in the liberator by approximately 20%. The second process involves adsorbing antimony and bismuth from the electrolyte by means of chelating resin. As the electrolyte passes through the packed column of chelating resin, antimony and bismuth are selectively adsorbed. They are then desorbed by means of hydrochloric acid, and then recovered in the form of a highly concentrated antimony chloride solution by means of evaporation. This process almost doubles the capacity for removing antimony from an electrolyte.

Jan 1, 1987

By R. J. St. Eloi

The Kidd Creek Copper Smelter has been expanded from its original design of 59,000 tonnes of copper per year to over 120,000 tonnes per year .. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and to .generally optimize the operation. The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to &apos;improve gas cleaning capability. The acid plant is reviewed with references to changes made to accommodate the increased S02 gas strength resulting from the higher smelting rates;

Jan 1, 1992

By C. J. Newman

The Kidd Creek Copper Smelter has been expanded from its original design of 59,000 tonnes of copper per year to over 120,000 tonnes per year. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and to generally optimize the operation. The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to improve gas cleaning capability. The acid plant is reviewed with references to changes? made to accommodate the increased SO2 gas strength resulting from the higher smelting rates.

Jan 1, 1992

By Onuralp Yücel, Mehmet Bugdayc, Murat Alkan

"In this study, iron based alloys (Fe-Mo, Fe-Cr-Ni, etc.) were produced by using aluminothermic methods starting from Mill Scales obtained continuous casting processes. Mill scales are an oxidised layer of steel alloys containing iron oxide, which includes + 2, + 3 values, on the surface of slabs and billets occurring during annealing in heating furnace at integrated iron and steel milling plant, and continuous casting unit. In the metallothermic experiments, different ratios of starting mixtures and addition of the oxide powders (Alz03, Si02, CaO, MgO) were examined, and their effects on the metal recovery and alloy compositions were carried out. The samples were characterized by using chemical analysis (AAS), XRD, XRF and SEM/EDS techniques.IntroductionSelf Propagating High Temperature Synthesis process (SHS) has many favour compared to the furnace applications, such as low energy requirement, low cost, very short processing time and simple operation, [l, 2]. In a SHS process, the ignition starts the combustion and propagates throughout the reactant mixture yielding the desired product. However, the disadvantages of the process such as inhomogeneous or unreacted products due to undesirable reaction rates needs to be overcome by changing some parameters such as ignition temperature, particle size, additive, atmosphere etc. [3, 4]. Mill scale is a layer of iron oxide which forms on ferrous materials cooling after being processed in hot rolling or continuous casting plants. Mill scale contains iron (II) and iron (III) oxides, which result in a 70% total iron content in oxide form. Not being able to reuse this material will prevent the raw material entering the production plant from being fully utilized [5]. This study aimed to produce Fe-based alloys via SHS (Self Propagating High Temperature Synthesis) metallurgy which is attractive process technique regarding fast and low-cost production ability of cast alloys by using high metallic iron content by reducing continuous casting mill scale."

Jan 1, 2013

By Lucas Barbosa de Souza Martins, Felipe Perissé Duarte Lopes, Nathalia Carneiro Garcia Rosa, Lucas Lopes da Costa, Sergio Neves Monteiro, Rubén Jesus Sanchez Rodriguez

"The fibers extracted from the stem of the banana plant are relatively stronger and have been used as reinforcement of polymer matrix composites. In addition to quasi-static mechanical properties, there is a need to characterize the dynamic behavior of banana fiber composites subjected to thermal and mechanical constraints. In this work, the temperature variation of the dynamicmechanical parameters of polyester composites incorporated with up 30% in volume of banana fibers were investigated by DMA tests. The storage and loss moduli as well as the tangent delta were measured from 20 to 200°C in a TA Instrument operated with the flexural mode at 1 Hz. The results showed that the incorporation of banana fibers tends to increase the viscoelastic stiffness of the polyester matrix. It was also observed changes in the T g and the structure dumping capacity of the composites with increasing fraction of banana fibers.IntroductionNatural fibers with high amount of cellulose, also known as lignocellulosic fibers, have been used from primeval times by our civilization. In the last century, synthetic fibers such as nylon, carbon, aramid and glass fibers gained interest owing to superior strength and precise dimensional control. Natural fibers were then replaced by synthetics in many fields such as textiles and appliances. In the past decades, however, environmental issues drawn, once again, the attention to lignocellulosic fibers as possible substitute for intensive energy-consuming and long term polluting synthetics, specially the glass fiber [1]. In particular, research works have disclosed the potential advantages associated with the use of lignocellulosic fibers as the reinforcing phase in polymer composites [2-7]. Among the advantages it is worth mentioning the renewability, recyclability, biodegradability and the fact that natural fibers are neutral with respect to C02 emissions responsible for global warming. Moreover, as compared to synthetics, lignocellulosic fibers present lower density and cost as well as reduced wear caused to the processing equipment. On the other hand, in terms of composite reinforcement, hydrophilic lignocellulosic fibers present drawbacks such as weak adhesion to hydrophobic polymeric matrices in addition to dimensional limitations and non-uniform properties."

Jan 1, 2011

By V. R. Voller

"The World Wide Web (the web) provides a very useful resource for the enhancement of teaching and research dissemination. This paper advocates that researchers take control of this resource and become actively involved in creating web content. Two examples of the use of the web in a materials setting is provided. The first illustrates how a concept quiz for teaching can be developed. The second shows how a materials processing model can be run in real time over the web. The paper closes with a summary of some resources that can be used to create web materials.IntroductionA recent copy of a newspaper advertisement read""Share what you know, learn what you don't""This neat phrase sums up a powerful teaching and research philosophy. In an educational setting a prime motivation for research is to uncover the unknown and venture in directions previously uncharted. The balance to this search for knowledge should be a desire to share that knowledge with others; whether it be with students in the classroom or research colleagues in a wider setting.The .World Wide Web and its associated multi-media software offer a perfect platform for researchers to share their knowledge with an extremely wide sector of the research community. To enable the use of this resource researchers must take the power that the web offers them into their own hands and create products that take maximum advantage of the medium. It is key that researches at the forefront become directly involved, otherwise a potential powerful medium will not realize it's true potential, and colorful products with no core content will proliferate. The object of this paper is to outline two ways in which the web can be used to enhance teaching and research objectives."

Jan 1, 2000

By Bora Derin

This work deals with the recovery of valuable metals from the ancient copper smelting slags located in Küre-Turkey. In this process, copper and cobalt were recovered in metallic form and/or as their compounds, whereas iron was recovered as magnetic oxide or pigment. Abrasive grit material was produced using reduced final slag. The process stages involved carbothermal reduction in a DC arc furnace, granulation, leaching, chemical precipitation, selective sulfidizing roasting and product preparations. In this paper, the process stages were described as theoretically and experimentally whereas slag and products were characterized in detail.

Jan 1, 2003

By D. Mishra

Electric arc furnace dust (EAFD) generated during the recycling of steel- scrap is classified as a hazardous waste for landfilling. This is because it contains leachable heavy metals such as zinc, lead,... Recovery of these metals could result in both resources conservation and resolving waste disposal problems. A study of the thermal reduction of a sample of EAFD was carried out in an inert gas atmosphere using coke as a reducing agent. Preferential volatilization of zinc and lead was achieved during the reduction process at about 800 "C. More than 96 % of both zinc and lead were removed from the dust and were recovered in the condensates. The treatment residue was essentially composed of iron oxides and almost free from heavy metals.

Jan 1, 2002

By Xudong Liu, Feng Chen, Yufeng Guo, Wei Chen, Tao Jiang

Willemite is typically found in oxidized zinc ores and metallurgical secondary resources but without effective extraction method yet. Based on the ideas of zinc phase reconstruction in the willemite, the extraction of zinc from willemite by calcified-roasting using CaO as additive and ammonia-leaching process was studied in this paper. The influences of CaO dosage, roasting temperature, roasting time on the phase transformation and zinc leaching rate were studied, which were characterized by XRD. The results indicated that Zn2SiO4 was transformed into ZnO or Zn2CaSi2O7 .After roasted with 1.4 times of theoretical CaO dosage at l280 for 40 minutes, willemite was thoroughly transformed into ZnO. The zinc leaching rate of the roasted sample was 97.45% in NH4Cl-NH3 H2O leaching system, which increased by 91.40 % compared with zinc leaching rate of 6.05% when willemite was directly leached in NH4Cl-NH3 H2O system.

Jan 1, 2016

By Tomás Vargas

The catalytic role of Thiobacillus ferrooxidans in the dissolution of chalcopyrite was studied by leaching pure massive samples of this sulfide with a pure strain of Thiobacillus ferrooxidans (ATCC 19859). Monitoring of the bacterial activity showed that an important fraction of the total bacteria generated during leaching remained attached to the chalcopyrite surface. Bacteria grown in the system, which were the offspring of bacteria adhered to chalcopyrite, was well explained as the result of the utilization of ferrous ion and sulfur as energy sources. The potential for indirect and direct action was fully utilized by the existing bacteria and the leaching process was controlled by the kinetics of chalcopyrite dissolution.

Jan 1, 1990

By cheng Peng-fei, TANG Hai-yan, guo Xiao-chen, LI Jing-she, Liang Yong-cang, Zhao Baojun

In the process of oxygen blast furnace, the lower coke ratio and the higher coke load make the skeleton coke more important. To understand the dissolution of coke in melting and dropping zone, the influence of FeO content, temperature and reaction time on the dissolution of coke with slag were studied by single-factor experiment. Meanwhile, the three factors and three levels orthogonal were conducted. The dissolution degrees were characterized by the weight loss ratio and diameter variation. The results showed that the weight loss ratio increased and the diameter decreased with the increase of FeO content, temperature and time. The three factors and three levels orthogonal test showed that time was the most significant factor on coke dissolution, FeO content of the second, and finally the temperature. The microstructure of coke after reaction indicated that the dissolution occurred on coke surface.

Jan 1, 2016

By Eric J. Beckman

Recovery of metals from dilute solution, whether the matrix is solid, or liquid, remains a considerable technical and financial challenge. Methods currently exist whereby metals can be extracted from either type of matrix, yet these methods consume significant quantities of reagents and can also generate multiple waste ,streams in the process. Technology developed in our lab allows efficient application of environmentally-benign CO2 to a number of separation problems involving metals. For example, we have employed biphasic mixtures of C02 and water as a green acid leach medium. Metals have been extracted from a steelmaking process residue and then recovered as metal carbonates through depressurization. In this process, metals are extracted and recovered without the use of reagents other than CO2 and water, and CO2 is sequestered as a solid. In addition, through synthesis of Cal-miscible phase transfer agents, we have shown that CO2 can replace the organic solvent currently used in refining of precious metals, The sensitivity to pressure of phase behavior in a CO2-mixture may allow significant streamlining of the process as well. Finally, CO2 soluble chelating agents have been used to extract toxic metals from acidic effluent such as that found in plating facilities.

Jan 1, 1999