Search Documents

By A. D. Davis

The former Homestake gold mine at Lead, South Dakota, has been selected by the National Science Foundation as the proposed host site for the Deep Underground Science and Engineering Laboratory. The deep laboratory and associated research campus will be developed at approximately the 7700-ft level. Plans also include the development of the Sanford Underground Science and Engineering Laboratory at the 4850-ft level. After the mine?s pumps were shut off in June, 2003, water levels rose to approximately the 4650-ft level by early 2008. Pumps in the 8150-ft deep mine were turned on again for dewatering in April, 2008. Instrumentation is being installed in the mine to measure water-level declines during pumping, for later analysis of permeability and related hydraulic properties of the formation. Pressure-sensitive transducers and data loggers will provide real-time information on water levels that will be available to interested parties. Quality of the water also will be monitored as it is pumped from the mine. I

Jan 1, 2009

By Djavid Mohammad

Over the next several years, the storage capacity of the Metropolitan Water Reclamation District of Greater Chicago?s Tunnel and Reservoir Plan will be increased by 14.8 billion gallons through the addition of two large off-line reservoirs: the McCook and Thornton Reservoirs. The Thornton Reservoir will be constructed at the terminus of Calumet TARP System. The constructed TARP system will be connected to the Thornton Reservoir via connecting tunnels and gates systems. The connecting tunnels will comprise of: an upgradient transition tunnel, steel lined bifurcated tunnel for conveyance and control of flow, downdradient transition tunnel, and energy diffuser at tunnel portal. A large, approximately 250-foot-long, 69-foot-wide, and 40-foot-high, rock cavern will be excavated at an average depth of 320 feet to house the bifurcated tunnel system and associated six large control gates, each 12.5-ft by 28-ft wheel gate. Presented in this article are discussions about the TARP system, the Connecting Tunnels and gates Project, regional rock conditions, evaluation of reservoir?s wall stability for evaluation of tunnel penetration, and design challenges facing during design of the: rock cavern hosting the bifurcated tunnel system and gates and associated tunnels and shaft.

Jan 1, 2008

By Ian Martin

A precious metals refinery’s switch to personal computer-based, three-dimensional piping design saved many hours in the design of a South African precious metals refinery. Bateman Minerals and Industrial provided engineering, procurement and construction management services for Impala Platinum Limited-Refineries’ new $60 million refinery in Springs, South Africa. This project is one of the largest platinum refineries in the world. Bateman evaluated a new design method during this project that involved developing a three-dimensional model for the project. The new method saved time by reducing the man-hours required to generate complete project documentation, including plans, sections, isometrics and material takeoffs. The new method also saved design and construction time by allowing designers to detect clashes before construction began.

Jan 1, 2000

By Satid Therdkiattikul, Donald A. Dahlstrom

By oxidizing the pyrite matrix through biological leaching of precious metals ores or concentrates, better than 90% recovery of gold and silver is achieved. The paper develops three precipitation processes that eliminates arsenic and all other toxic elements in the resulting liquor after the biological reactors. In addition, the precipitates are highly crystalline and resist resolubilization. The latter must be tested for at least six months by EPA test procedures. The three systems are temperature (must be at least 120°C or higher) lime or limestone. A continuous pilot plant was employed for all three systems and complete recommendations are given to optimize Fe/As molar ratio, reaction kinetics (detention time) pH, temperature, wt % feed solids as well as resultant reagent consumption based upon continuous operation.

Jan 1, 1995

By H. K. Lin

Cyclic voltammetric and potential step chronoam-perometric techniques were used to study gold dissolution in cyanide solution. Three distinct anodic and one cathodic peaks appear on the voltammogram between -0.50 and 0.80 V vs SCE. The corresponding reactions were proposed to explain the peaks and the passivations. The proposed reactions were in agreement with the effect of pH, cyanide concentration and the rotating speed of the electrode on the magnitude of the peak currents. Cyclic voltammetric tests, with various vertex potentials, were also conducted to examine the proposed reactions. Steady-state currents at various potentials were obtained by potential step chronoamperometric technique and were compared with transient currents obtained by the cyclic voltammetric technique.

Jan 1, 2000

By Rajni Patel, John McDonald, Steve Dubnewych, Michael McKenna

The Upper Reach segment of the Northeast Interceptor Sewer (NEIS) is a3.2-km-long tunnel excavated in interbedded marine sedimentary deposits with approximately 40 m of cover. The tunnel was initially classified by Cal/OSHA as “potentially gassy.” During excavation, high levels of hydrogen sulfide and methane were encountered, prompting Cal/OSHA to reclassify the tunnel as “gassy.” In addition, the tunnel excavation encountered an abandoned, 100-year-old water tunnel known as the “Narrows Gallery.” This existing tunnel was completely full of water and under 30 m of hydrostatic head. This paper will discuss the unanticipated difficulties and design solutions implemented to construct a gassy tunnel exposed to high volumes of water.

Jan 1, 2005

By Y. Nien Wang

The Devil?s Slide portion of Highway 1 between Pacifica and Montara is often closed due to the instability of the adjacent slopes. Following many years of public input and careful evaluation of alternatives, Devil?s Slide will be by-passed via two inland tunnels, providing a safe, dependable highway between Pacifica and Montara. For the twin tunnels, each 9m diameter tube will accommodate only one traffic lane. Each tunnel tube will accommodate a 3.6 meter roadway, 0.6 meter and 2.4 meter inside and outside shoulders respectively, and 1.2 meter walkways on each side. Cross passages will connect the bores at about 120 meter intervals and jet fans will provide tunnel ventilation. The twin tunnels are approximately 1,250 meter long and 9 meter wide. Excavation will progress from south to north using tunneling techniques that rely on inherent rock strength for support known as the New Austrian Tunneling Method (NATM). Both tunnels will be excavated at the same time, one tunnel face approximately 40 meters ahead of the other. Staggering the tunnels reduces the likelihood of damage from blasting in alternate tunnels. The work schedule is 24 hours a day, 7 days a week resulting in a 24-month timetable to break through to the north portal.

Jan 1, 2008

By G. D. Mainwaring, Weng L. W, Lam Y. K.

The first power transmission cable tunnel in Singapore was the 2.6km long undersea tunnel between Pulau Seraya and mainland Singapore, constructed in the1980s. Ten years later, similar concepts were used for the Tuas Cable Tunnel. The tunnel, which includes a 2.2km long immersed tube section, was designed to accommodate 10power circuits of 400kV and 230kV capacity. It is fully equipped with sophisticated control and communication equipment, fire suppressant and life safety systems plus a maintenance vehicle which runs on tracks through the length of the tunnel. The paper discusses the planning, design, and construction of the Tuas tunnel, and the development of these concepts for future tunnels.

Jan 1, 2001

By A. Zeni, S. L. Bessinger, T. A. Palm

San Juan Coal Company (SJCC) operates an underground coal mine near Farmington, New Mexico. Continuous miners and a longwall produce 7-8 million tons per year. The coal seam at SJCC has tested to have a propensity for spontaneous combustion. As such, during feasibility for this project, it was elected to utilize a bleederless ventilation system on the longwall. Three-entry gateroads are developed, and the longwall gob is sealed as mining progresses. SJCC utilizes a nitrogen injection system to continuously inertize the gob. In 2004, the mine was nearing completion of its first longwall district. The next district would contain longer panels (up to 12,500 feet). Due to the liberation of methane, and to a lesser extent hydrogen sulfide, a typical wrap-around ventilation system would not be appropriate. Not only would gas concentrations likely be challenging, but the overall ventilating pressure in the mine would have to be increased beyond limits established to mitigate the potential for spontaneous combustion. Given the above-described operating constraints, SJCC determined a need for a small ventilation shaft in the back (longwall setup area) of the next district that would draw adequate air past the longwall seals to maintain low gas levels and permit the required regulatory inspections to occur. Extensive ventilation modeling and gas desorption testing indicated that the shaft would be required to handle a volume of air ranging from 40,000 cfm to as high as 185,000 cfm. This large range is driven by the position of the longwall face with respect to the shaft and the effectiveness of the SJCC degasification program (SJCC uses vertical gob vent boreholes and horizontal in-seam methods). Ventilation simulations determined an appropriate diameter for the 350-ft-deep shaft to be 5 feet. Having determined shaft size, the next decision related to the method of shaft construction. Conventional shaft sinking was ruled out, due to the small diameter. Raise boring was an attractive option but had two drawbacks: (1) development crews would reach the bottom of the shaft just a few weeks before longwall startup, leaving a compressed timeframe to install the shaft, and (2) raiseboring requires additional underground entries to be developed to stow the project’s cuttings. While raiseboring remained a viable option, the problems associated with it led SJCC to also investigate blind drilling.

Jan 1, 2006

By M. Mikhaylenko

The most common methods of processing of uranium ores is sulfuric or carbonate leaching with conversion of hexavalent uranium to uranyl carbonate or sulfate anionic complexes followed by sorption of the later by strong base anion (SBA) exchange resins. It is known that chloride anion has high affinity for SBA resins so that it depresses sorption of anionic complexes of uranyl. Application of the SBA resins becomes impractical for recovery of uranium when chloride concentration in pregnant leach solution exceeds 3-5 g/l [1-3].

Jan 1, 2012

By Georgene Renner, William R. Yernberg, William Gleason

American Commercial (ACI) offers a selection of ground control solutions. Beginning with steel liner plates installed in the Gratiot Avenue sewer system in Detroit, MI 1920, ACI is one of the leading designers and manufacturers of underground steel supports in North America. ACI is also a leader in fire-proofing underground structures with its Promat Fire Protection Boards. The sandwich panels have been used in many new and retrofit tunnel and underground construction projects worldwide. Ease of installation and replacement, cost effectiveness and superior performance have made this product line the premier choice of owners and designers for structural protection, fire-life safety requirements and architectural finish needs.

Jan 1, 2007

By Heiner J. Sander

Stanford University operates the National Research Facility which is located at the Stanford Linear Accelerator Center (SLAC) in Menlo Park, California. In order to improve and allow for enhanced experiments, the current facilities required expansion. A1500 foot long tunnel (20 ft wide by 21 ft high) and a 220 foot long underground cavern (49 ft wide by 32 ft high) were excavated through the Ladera Sandstone formation which is an intermediate geo-material with week rock properties. The overburden between surface and crown of the structures varies from 10 to 80 feet. The underground structures were excavated according to the principles of the NATM (New Austrian Tunnel Method). This paper addresses the challenges that were encountered during the construction phase of the project and how construction issues were resolved mutually by the owner, engineer and contractor. The implementation of geotechnical instrumentation, recorded data and interpretations, soil conditions and behavior encountered during construction are also presented.

Jan 1, 2008

By Dennis Ofiara

Several recent tunnel jobs have required special adaptations of hard rock TBMs. Some of the special job conditions are ?no blast? launch requirements, small shafts or launch pits, proximity to existing underground structures, and short tunnels where the TBM must be retrieved through the primary lining. This paper describes a few of these projects, and the machine adaptations that have made TBM excavation feasible.

Jan 1, 2008

By William M. Gleason

When SME’s 2006 Arizona Conference convened in December at the Hilton El Conquistador Resort in Tucson, AZ, there was considerable excitement among the 387 attendees. There was a noticeable buzz surrounding the progress of Phelps Dodge’s Safford copper mine in southern Arizona, one of the first new major copper mines to be permitted in more than 30 years in the United States. There were also plenty of good feelings about the mining industry in general. Commodity prices remained high and with no signs of a slowdown in the immediate future. Things were good in Arizona. But there were also cautionary tones at the conference and the Mining Foundation of the Southwest banquet that preceded it.

Jan 1, 2007

By M. Martins

This work presents and discusses the influence of the surface tension (gLV) of methanol/water mixtures on the flotation response of apatite versus gangue minerals conditioned with flotation reagents (75 g/t cornstarch and 100 g/t Berol 867) at pH 10.6. Berol 867 is a collector composed of sodium alkyl sarcosinate plus nonionic surfactant. The highest Schulz efficiency of separation (recovery of apatite minus recovery of gangue) was achieved at ?51.0 mN/m. The critical surface tension of wettability (gC) of apatite was found to occur at 34.7 mN/m when determined by means of gamma flotation experiments, and it was 33.9 mN/m when determined by Zisman?s approach.

Jan 1, 2009

By J. Kretschmann

Around the world, mining has been done for thousands of years for the benefit of humankind. The winning process in mining operations ends with the depletion of the deposit or its closure if the operation becomes economically unprofitable. After that, a period of post-mining follows which may last for a very long time and which is generally regarded as a period of hazards, risk and high cost. In the USA alone, approximately 500,000 abandoned mines do exist; worldwide, there are millions. In Germany, too, we have had to deal with abandoned mines for a considerable period of time now.

Jan 1, 2012

By J. C. Schneider, G. Van Weert

Hydrochem Developments Ltd. has developed and put into full scale operation a novel type of vertical flotation column incorporating a multiplicity of mechanically agitated stages. Characteristics of this flotation column include a low height to diameter ratio, high upgrading factors and the possibility of modifying geometry and operation to specific flotation requirements. A commercial unit is currently handling up to 100 tpd rougher concentrate at Dickenson Mines Limited, Balmertown, Ontario. Design parameters and plant performance will be discussed.

Jan 1, 1988

By Bruce W. Woolpert

During the SME Board of Directors’ midyear meeting in Monterey, CA Aug. 25, I discussed trends in the construction aggregates industry. Many construction-material suppliers may not have yet fully internalized the changes that are taking place. But the changes are significant. And they have shifted the focus in the aggregates industry from “assets” to “people and innovation.” Construction-material suppliers serve many customers. A typical quarrying operation at Graniterock would have more than 1,000 customers, mostly civil engineering contractors. Along with the push toward people and innovation, there is increased emphasis on vertical integration from aggregates to ready-mix concrete and hot mix asphalt, to final construction. If a company is not vertically integrated, it will at least have strong partnerships with other firms, to deliver a high-quality finished project on time.

Jan 1, 2002

By Charles Ronkos, Jeffrey Edwards, Brian Brodsky

The Marlin gold-silver deposit is in western Guatemala, 15 kilometers south of a major transform fault that separates the North American and Caribbean plates. A district-scale, northwest-trending graben controlled deposition of a greater than 1200 meter thick upper Tertiary quartz latite to rhyolite volcaniclastic sequence. These volcanics were subsequently intruded and unconformably overlain by a small intermediate, latite to andesite, volcanic complex. Classic low-sulfidation, quartz-calcite-adularia veins and stockwork formed a 2.2 million ounce gold deposit, in association with late-stage andesite dike swarms, along a west-northwest striking normal fault on the eastern flank of the volcanic complex.

Jan 1, 2005

By M. Botz

Anatolia Minerals Development Limited (AMDL) is constructing the Çöpler Gold Project in eastern Turkey and commenced mining in the fourth quarter of 2009 with gold production scheduled to begin in the fourth quarter of 2010. The project is a 15,500 tonnes/day oxide heap leach with three-stage crushing, agglomeration, carbon adsorption and electrowinning for final metal recovery. Leach solution copper levels are expected to be relatively low during the first two years of production but will increase in later years due to higher copper content in the mined and processed ore. Over the mine life approximately 40 million tones of ore will be placed on the leach pad, which will contain about 35,000 tonnes of copper. Metallurgical testing indicates copper extraction will vary by ore type and, if controls are not implemented, may lead to copper levels exceeding 1,000 mg/L in pregnant solution. High copper levels in leach solution have the deleterious effect of increasing cyanide consumption and potentially overwhelming the ability of the carbon circuit to effectively adsorb the principal economic metals, which in this case are gold and silver. Using data obtained from laboratory leach column testwork, the heap leach facility was modeled using METSIM process simulation software to estimate the build-up of copper in leach solution over the mine life. Laboratory testwork was also performed to evaluate process conditions for treating a portion of pregnant leach solution via sulfide addition to precipitate saleable copper as copper sulfide (Cu2S).

Jan 1, 2011