Search Documents

By B. K. Cantrell

The U.S. Bureau of Mines and others have conducted a number of occupational exposure surveys since the publication of the International Agency for Research on Cancer report of 1989, which labeled diesel exhaust as a probable human carcinogen. These surveys have assessed diesel exhaust exposure using measurement of diesel aerosol and/or specific polycyclic aromatic hydrocarbons as indicators of exposure. This paper reviews present diesel emission standards, available diesel exhaust aerosol measurement techniques, and the results of the occupational exposure surveys. In the surveys, diesel aerosol was emphasized because it is a major component of diesel exhaust, is suspected to contribute to the health hazard, and is readily measurable. Three primary aerosol measurement techniques were used: respirable combustible dust, size-selective sampling, and measurement of the elemental carbon fraction. Occupations surveyed included mine workers, railroad workers, forklift operators, fire fighters and truck drivers. The studies found mean diesel aerosol concentration levels in the range of 0.004 to 1.74 mg/m3? Highest aerosol exposures were in confined spaces such as mines where heavy diesel equipment is used. Polycyclic aromatic hydrocarbons typically are found at very low concentration levels and are not unique to diesel exhaust.

Jan 1, 1996

By P. Eger

Minnesota contains a major low- grade copper-nickel sulfide resource within the Duluth Gabbro Complex. Several companies have actively explored this resource. Open pit mining would be required to develop portions of the resource, and as a result, large quantities of sulfide-bearing lean ore and waste rock would be stockpiled. Although the problems associated with high-sulfide tailings and acid mine drainage are well documented, the leaching characteristics of low-grade mineralized stockpiles must be understood for environmental impact assessment, siting, and planning. The Minnesota Department of Natural Resources and AMAX have cooperated in a research program to study leaching and revegetation -of test stock- piles, Six small (1600 'tons) stockpiles were constructed at the MINNAMAX Project Site and they range in composition from 0.29 to 043 g % copper, 0.075 to 0.09% nickel, and 0.6 to 1.45% sulfur. Two of the stockpiles were covered with mineral soil, one was covered with topsoil, and three were not treated Revegetation plots were established on the piles which received a soil cover. Leachate samples and flow measurements were collected at the base of the piles. Initial results indicate that metal concentrations in leachate samples range from 10 to 10,000 times the concentrations found in the streams of the area. During the first growing season, the test pile covered with topsoil yielded 30% less water than untreated test piles. No reduction in yield was observed for the piles that were covered with the less fertile mineral soil. First-year vegetative growth, expressed as biomass, was four times greater on the-topsoil pile than on the mineral soil piles. The long-term effects of vegetation on leachate quantity and quality continue to be investigated.

Jan 1, 1980

By Volkan Arslan

This study aimed to remove the contaminants in quartz sand by using an eco-friendly method and to obtain high-purity quartz. For this purpose, ultrasound-assisted acid leaching was applied. Equal amounts of a mixture of diluted hydrochloric and oxalic acids were used as the solvent. Response surface methodology (RSM) was used for optimizing, modeling, and predicting the experimental parameters. The correlation coefficient ( R2) of the proposed quadratic model for the relationship between iron removal yield and test parameters was calculated as 0.9731 and it was determined that the predicted and actual values were compatible. Finally, optimization experiments were made and optimum experiment conditions were revised and determined as 83.38 °C of leaching temperature, 196.35 min of leaching time, 2.86 M of acid concentration, and 202.24 W of ultrasound power. Under the optimum conditions determined after optimization, the highest yield of iron removal was determined as 95.08%. Under the optimal parameters, the SiO2 content of the concentrates increased from 97.841 to 99.907% and the Fe2O3 content reduced from 0.225 to 0.011%.

Jul 12, 2021

A viable mineral economy requires availability of economic deposits, the ability to exploit then, and protection of the public interests. The natural tendency for each party to consider only its legitimate self interests can lead to delays or deadlocks. The paper presents several viewpoints aimed at opening each party's mind to the ideas of others in the hope that negotiations might be more reasonable and rapid for the benefit of all concerned.

Jan 1, 1979

By O. Babak, O. Leuangthong, M. A. Cuba

Integration of data from multiple sources and/or multiple scales is a common, yet challenging aspect of geostatistical resource modeling. Common approaches to data integration are based on a cokriging framework that assumes a consistency of scale in the information that leads to a requirement to composite the data prior to model construction. It is well known that the geostatistical model parameters are scale dependent. In particular, the volume variance of integrating these various scales has a direct impact on the semivariogram that should be used in model construction and/or the assessment of volume-variance relations as it affects resource estimation. This paper reviews and compares two different approaches for semivariogram upscaling. The first approach is the scaling laws. It is an empirically derived approach, involving several simplifying assumptions, one of which is a strict assumption of invariance of the semivariogram shape. The second approach is a theoretically derived direct upscaling of the semivariogram. This approach has been around for a number of years, but is seldom implemented due to software limitations. In this paper, we present a numerical integration approach to facilitate direct semivariogram upscaling. The advantage of direct upscaling over the scaling laws approach is shown by considering a synthetic example and a case study. Further, in the case of multiple codependent random variables, the extension of the direct semivariogram upscaling to the cross semivariograms is derived and an upscaled consistent linear model of coregionalization is presented.

Jan 1, 2013

By B. E. MacNab

During the past several years, Raymond Kaiser Engineers has prepared numerous studies concerning the technical and economic feasibility of coal exporting facilities in the western United States. Perhaps the most striking conclusion to be drawn from these efforts is that many people underestimate the complexity of the highly competitive, dynamic coal marketing system which includes coal loading terminals as an essential but relatively low-cost link in the energy production and delivery chain. The title of this paper, "The Status of Western United States Coal Ports - An Economic Assessment," should not delude anyone into thinking that the future of western U.S. coal- exporting ports has now congealed into a well- defined economic plan. As this paper will demonstrate, the situation is complex and more dynamic than ever and promises to remain so into the late 1980's.

Jan 1, 1982

By Shawn P. Coughlin, Michael A. Schimmenti, Juan Leonardo Tello del Pino

"The Sistema de Potabilización Área Norte project (Northern Area Purification System) was a major expansion of the potable water system in Buenos Aires Province, Argentina. The aim of the project was to transport and purify raw water from the Paraná River to provide potable water for five communities in the northern part of the province, benefitting up to two million people. The project was constructed by a joint venture (JV) of four South American contractors and consisted of the following key components:• Treatment plant: A 16-ha (39-acre) area was cleared for the construction of a treatment plant to purify 900,000 m3/day (1.2 million cu ft/d) of raw water from the Paraná River and distribute it to the surrounding communities.• Bored tunnel: Nearly 15 km (9 miles) of 3.6 m (12 ft) inner diameter tunnel, ranging from 18 to 22 m (59 ft to 72 ft) below grade, was bored with two earth pressure balance (EPB) tunnel boring machines (TBM) to draw the raw water from the river. The TBMs started from a central launch shaft and proceeded in opposite directions. Cristina advanced northbound to the Paraná River Intake System, and Liliana advanced southbound to the new treatment plant.• Access and ventilation shafts: Five access shafts and eight ventilation shafts were installed along the length of the tunnel. The access shafts were designed to provide entry points for inspection and maintenance of the final tunnel. The five shafts consisted of one central launch shaft in the middle of the tunnel alignment, one retrieval shaft at each end of the tunnel (intake and treatment plant, respectively) and two intermediate shafts. The intermediate shafts were installed before the TBM passed, with a final liner to be installedafterward."

Sep 1, 2016

By Robin J. Hickson

El Abra is one of the world’s premier copper de-posits. The project is located in northern Chile, 140 km (87 miles) inland from the Pacific coast. It has the same geologic age and structural setting as the world-class Chuquicamata copper mine located 42 km (26 miles) to the south. The current development plan for El Abra extracts798 Mt (879 million st) of high-quality oxide ore. This will require building a solvent extraction/electrowinning(SX/EW) facility that can produce 225 kt/a (248,000stpy) of cathode copper. This will make El Abra the largest SX/EW copper operation in the world, and the world’s seventh-largest copper producer.

Jan 1, 1996

By S. S. Hsieh

Bench-scale beneficiation studies were made on Idaho dolomitic phosphate rock using the TVA carbonate flotation process. The process employed diphosphonic acid as a phosphate mineral depressant and fatty acid as a carbonate mineral collector. Silica was subsequently rejected as float using an amine collector, with phosphate product recovered as the sink fraction. Two samples of prepared flotation feed from commercial operation were used; one contained 21% P205 and 3.2% MgO, and the other contained 26% P205 and 1.8% MgO. The results indicate that concentrates containing 31-33% P205 and 1% or less MgO can be obtained, with P205 recovery of about 80%.

Jan 1, 1984

By Roger D. Sharpe

Oklahoma contains extensive resources of high-purity gypsum that were deposited in the Anadarko and Hollis basins during Permian time. The gypsum resources and reserves are estimated to be about 48 billion short tons and a; located in the western portion of the state. Oklahoma is the largest producer of gypsum products in the United States. The Blaine Formation and the Cloud Chief Gypsum contain several beds of minable thickness. Four stratigraphic units in the Blaine Formation are quarried in Oklahoma. The Shimer, Nescatunga, and Medicine Lodge Members are quarried in northwest Oklahoma. The Van Vacter Member, consisting of three gypsum beds, is quarried in southwest Oklahoma. The Cloud Chief Gypsum is quarried in the west-central part of the state. The gently dipping gypsum in the Blaine Formation generally crops out along low escarpments and is covered in the downdip direction by increasing overburden, consisting of sand, shale, and/or dolomite. Anhydrite occurs in the downdip direction under the thicker overburden. The Cloud Chief Gypsum crops out as hills, which are eroded remnants of a more widespread, massive sulfate unit. All of the gypsum produced in Oklahoma is extracted using quarrying methods. A variety of products are made from gypsum quarried in Oklahoma. The products are manufactured from uncalcined, calcined, and deadburned gypsum. Products vary from raw, ground gypsum used for agriculture, to high-value-added industrial plasters, cements, and fillers produced from calcined gypsum. A sampling of the many products manufactured from Oklahoma gypsumincludes: (1) agricultural-soil amendment; carrier for insecticides, pesticides, and herbicides; calcium supplement in animal feeds; (2) gypsum wallboard-common, fire-resistant, and water-resistant varieties; (3) industrialgypsum plasters-art and casting, pottery and ceramic, molding and tooling, crayons, wall patching; (4) industrial gypsum cements-oil-well cement, high-strength statuary, high-strength tooling, fiber-reinforced architectural, road and bridge repair; (5) food and pharmaceutical-filler and binder in aspirin and other medicines, yeast activator in brewing of beer, moisture absorbent in bread and pizza dough; and (6)portland-cement retarder-ground with clinker to control setting time.

Jan 1, 1999

By Lawrence L. Davis

This paper describes current research by the Bureau of Mines to develop technology for improving efficiency and productivity in metal/ nonmetal mines. The research program addresses a wide variety of problems associated with each of the major categories of mining: underground mining, surface mining, in situ mining, and premining investigations. An overview of the Bureau's research activities is given with emphasis on underground mining. In particular, two innovative and promising concepts currently under development are described: a unique shaft sinking system that uses an impact hammer for rock fragmentation, and a low-profile, portable crusher for underground hard-rock applications.

Jan 1, 1979

By S. Chander

A series of nonionic and anionic surfactants were tested to enhance the flotation response of a low rank coal. An ethoxylated octyl phenol and several polypropylene polyethylene block copolymers were tested as nonionic surfactants. The anionic surfactant was a dioctyl sulfosuccinate. All the surfactants employed improved the yield significantly but the influence on grade was complex. Separate studies were conducted to determine the emulsification behavior of the surfactants. For the nonionic water soluble reagents tested, a correlation between emulsifying power of the surfactant and flotation was observed. An increase in the number of droplets produced in surfactant containing systems was considered to be the main reason for increase in the yield. Since it increased the number of collisions between dodecane droplets and coal particles. When a surfactant was introduced into the flotation pulp prior to addition of dodecane, it decreased the benefits of the surfactant significantly. The decrease was attributed to an increase in the wettability of coal and a decrease in the surfactant available for emulsification. When a suitable surfactant was added as a solution dissolved in the oily collector, a considerable increase in yield was observed.

Jan 1, 1993

By ETHAN FUSTER, Richard Ray Jr, STEPHEN LEE

The abstract states that horizontally-mounted jet fans are commonly used to ventilate vehicular tunnels due to their space and cost savings compared to fully ducted systems. It highlights the successful use of vertically-mounted jet fans in exhaust ventilation shafts for a passenger rail overbuild in New York City. The paper compares shaft dimensions, jet fan placement, and measured airflows, also comparing these measurements to predictions from computational fluid dynamics (CFD) simulations.

Mar 16, 2022

By VIVEK KUMAR HIMANSHU, M. P. Roy, P. K. Singh, A. K. Mishra, RAVI SHANKAR

Blasting with the aim to reduce oversize boulders in underground has many hurdles due to limited accessibilities and poor site conditions. Optimized drilling and blasting parameters can help to achieve this objective. The major challenges of the blast designers lie within deciding blast geometry, namely drill hole diameter, burden, and spacing. The general approaches covered worldwide to determine burden-spacing are based on various rules of thumb, which are based on previous experiences of blasts and the associated outcomes. However, many parameters influencing optimum burden-spacing to achieve desired fragment size are site specific. Sometimes drill geometry is decided based on associated blasting hazards rather than rock fragmentation. The Kuz–Ram model is a worldwide accepted rock fragmentation predictor. The parameters associated with this predictor also include burden-spacing for a blast. Back calculation of burden-spacing from the Kuz–Ram model can be used to achieve desired fragment size. This paper deals with burden-spacing determination by using an empirical approach for the underground stope ring blasting.

Jan 4, 2020

By John D. Price

In the constant search for ways and means of improving the quality of coke and thus making its use at the blast-fornace more satisfactory and economical, it has become increasingly evident that the present laboratory tests do not show the full picture of a coke's value as a blast-furnace fuel. This fact was recognized by Dr. A. C. Pieldner thirty-five years ago: (Ref. 1) here is perhaps no phase of fuel technicology which has aroused more discussion or regarding which there is more difference of opinion than the properties of coke which make it most suitable for blast-furnaces and other uses." Dr. Fieldner followed this assertion with a statement to the effect that men who write on this subject today (1923) have, because of conflicting experimental evidence brought forth in recent years, far less positive opinions on the matter than did writers of some years past. One is led to wonder if these statements are not just as true now as they were when first made.

Jan 1, 1959

By S. H. Brown

In our work as health physicists*, we do a lot of public speaking and interaction with the public on issues related to development of uranium mining and milling (?uranium recovery?) in the US. Understandingly, the public has important concerns about this. Accordingly, this paper is presented in a ?question and answer? format in which we have tried to capture what are some of the most common concerns we hear from citizens and address them. We have attempted to do so based on the best scientific information we have, representing information well documented in peer-reviewed scientific literature and consensus positions from both national and international scientific standard setting bodies and related committees. We have included some of the more important of these scientifically-based references to support the information provided. Practical space limitations prevent completeness in this regard in some cases. Visit the Health Physics Society?s web site or feel free to contact me directly for additional references, information or detail ? Steve Brown. The health physicist?s primary objective is to manage the beneficial uses of ionizing radiation while protecting workers and the public from potential hazards. For more information on what a health physicist is and on the Health Physics Society, visit the Society?s web site at www.hps.org.

Feb 23, 2014

By Ari Jokilaakso, Junjie Shi, Zhuo Chen, Pekka Taskinen, Xiang Gao

The amount of copper flash smelting slag has increased during the recent years along with an increasing slag-to-metal ratio. During slag tapping, some copper sulfide is mechanically entrained. As a result, it is necessary to recover copper matte from the slag by suitable methods. At present, the most common way is slow, controlled cooling in a transfer ladle. However, research on the detailed effects of slow cooling and the function of slag modification is rare. This paper described experiments that were performed at different cooling rates (0.5, 1.5, 3, and 7 °C/min), with and without additive. A detailed characterization of the copper-rich phase and its particle size was subsequentlymade using SEM-EDSmicrographs and image analysis software.With a decrease in cooling rate, the particle size of the copper-rich matte phase became larger. The addition of gypsum and carbon as a slag modifier affected the size of the copper-rich phase slightly, and its chemical composition was modified compared with the experiments without additive.

Jul 31, 2020

By Immo H. Redeker

The Kings Mountain area of North Carolina is the lithium pegmatite center of the U.S., if not of the whole world. We have two spodumene and by-product mineral producing companies, Lithium Corp. of America, and Foote Mineral Company. We also have Kings Mountain Mica and Kings Mountain Silica Companies producing mica. feldspar, quartz and clay from weathered pegmatites in that area. Figure 1 gives the location of the spodumene pegmatite area in North Carolina. The two spodumene producers mine typical pegmatite ore in open pits after removing amphibolite or mica schist overburden which is sold to aggregate producers. The ore reserves are discussed elsewhere in this session. They are in the order of plus 50 million tons but not unlimited. 1.2 The major minerals found and concentrated from the North Carolina spodumene pegmatite ores are tabulated on Table 1.

Jan 1, 1977

By Jr. Babcock

The Pyke asbestos deposits were discovered by Kennecott Explorations (Australia) Pty. Ltd., in 1969 during the course of base metal exploration on the South Island of New Zealand. Extensive occurrences of chrysotile asbestos were found associated with the Red Mountain Ultramafics in the headwaters of the Pyke River, and to the north and south along the ultramafic belt for a distance of 70 kilometers. Surface evaluation and drilling by Kennecott in 1970 and 1971 identified numerous small deposits of good grade fibre in the Little Red Hills between the Pyke and Barrier Rivers. Additional drilling and three adits have been completed by other companies since that time. The property is presently held by Lime and Marble, Ltd. Of Nelson, New Zealand, and Kennecott Explorations (Australia) Pty. Ltd. This paper will present the regional and local setting of the asbestos deposits, including the geology and nature of mineralization. In addition, the exploration methods used by Kennecott in the discovery and evaluation of these deposits will be outlined. Subsequent work by other companies will be mentioned, but not described in any detail. This subsequent work did not alter Kennecott's conclusions or produce any serious changes in the interpretation of geology and mineralization. The author acknowledges the contribution of the many employees of Kennecott Explorations (Australia) Pty. Ltd., who have been involved in the project, particularly Ramon Farmer, N. G. Comer, and A. W. McConie, who were responsible for completion of field work and reporting on the project. The responsibility for the conclusions and interpretations of this report are solely that of the author and result from his involvement in discovery of the deposits and management of the exploration program.

Jan 1, 1978

By T. Bauerle, G. Poplin, Z. Dugdale

"The issue of mine worker fatigue is as complex as it is understudied. Generally, worker fatigue lies somewhere on a continuum between psychology and physiology, which makes the measurement and management of it difficult with no easy solutions for operators or workers. Answers to even basic questions remain elusive—such as what is fatigue, how is it measured, and how can organizational resources reduce fatigue—and answers seem to present no single, clear path to action for the health and safety of the worker. This manuscript supplements the growing body of interest in the problems of fatigue in the mining industry by reviewing some of what is known about worker fatigue in general and in the mining industry in particular. The material covered here includes basic topics of the hows and whys of worker fatigue; an overview of fatigue models, findings, and evidence-based solutions with a focus on mining; and potential future directions aimed at mitigating miner fatigue. INTRODUCTION “It is recommended that the whole fatigue test problem be stated in a form the nature of which may be indicated by the following suggestions: that the term fatigue be absolutely banished from precise scientific discussion, and consequently that attempts to obtain a fatigue test be abandoned [emphasis added].” – Bernard Muscio, Pioneer Australian Philosopher and Industrial Psychologist, in a 1921 Report to the Cambridge Industrial Fatigue Research Board Fatigue presents several challenges for the mining industry. Depending on the specific occupation, daily work, or operational setup on any given mine site, mining jobs can have a fair amount of labor-intensive tasks mixed with monotonous and repetative duties. Combined with the long working hours and shift-work schedules of mining work, the prevalence of fatigue in mine workers may seem rather unsurprising. On the one hand, mining is certainly not alone in facing the challenge of addressing worker fatigue. Indeed, many of the characteristics above mirror the similarities of fatigue in other industries, such as health care, aviation, and security. To the extent that fatigue in mining acts like fatigue in any other industry, then any fatigue management applications, trainings, or interventions in existence can be borrowed from other industries and applied to mining in a “cookie-cutter” approach. On the other hand, some have argued that mining in particular is especially susceptible to increases in the prevalence of fatigue beyond the characteristics listed above due to the multifaceted combination of factors in mining environments associated with fatigue: dim lighting; limited visual acuity; hot temperatures; loud noise; highly repetitive, sustained, and monotonous tasks; shiftwork; long work hours; early morning awakenings; and generally poor sleep habits (Canadian Centre for Occupational Health and Safety, 2012; Legault, 2011). Legault (2011) in particular argues that it is the combination of these factors simultaneously that can make mineworkers particularly susceptible to sleep deprivation and fatigue in comparison to other industries where these factors are often not present alltogether. If fatigue looks and acts different in mining, as others have argued, more research is needed to determine if, how, and why worker fatigue might need to be managed differently in mining."

Jan 1, 2018