Search Documents

By E. G. Kelly

This paper describes the performance of a modern compound trough profile spiral that is optimized for fine coal cleaning. Reduced performance (Tromp) curves are presented to compare these new spirals with older designs, as well as with other commonly used coal cleaning equipment. As an aid to equipment selection and circuit design, data are also presented to show how variables, such as flow rate, pulp density, and particle size affect efficiency and the separation specific gravity.

Jan 1, 1984

By Franklin B. Woodbury

As part of its goal of helping maintain an adequate supply of minerals to meet national economic and strategic needs, the U.S. Department of the Interior's Bureau of Mines is evaluating alternative technologies to treat oxidized taconites. Since process control is an essential element in the application of these process technologies, research was performed with a prototype monitoring system. A Californium-252 neutron source and a thermal neutron capture- gamma ray spectra analysis method was utilized to measure the amount of iron and the percent solids in the process slurries. The concentrate and tailing streams in a 410-kilogram-per-hour (900- pound-per-hour) pilot plant employing a selective flocculation and cationic flotation process were monitored. The results obtained showed that the thermal neutron capture-gamma ray reaction can be used to provide process control parameters.

Jan 1, 1979

By T. M. Yegulalp

A new explanation of the scale dependency of the strength properties of rock is presented based on the theory of extremes. A review of past work on specimen size strength relationship is followed by an introduction to the fundamentals of the underlying theory of extremes and its relationship to the scale effect on the statistical properties of the strength distribution. It is shown that the weakest link theory is directly related to extremal statistics and properties of strength distributions of rock can be derived as a function of the specimen size. Three sets of Brazilian test data are used to demonstrate the use of this approach.

Jan 1, 1992

By John H. Lichtblau

There are three parties to the oil imports controversy: the domestic oil producers, whose side has just been ably summarized by Mr. Jameson; the oil importers; and the public. Domestic producers and importers are both motivated by economic self-interests, that is by their natural and legitimate desire for profit maximization, in their respective positions. Thus, domestic producers, rightly, regard every barrel of imported crude oil (with the exception of some specialty crudes) as a displacement of a barrel of their own crude. Hence, the lower the import Level the better they like it. Conversely, U .S. refiners whose plants are located at the seaboard or at certain inland waterways generally welcome a higher level of imports because refiner profits are based primarily on the spread between the crude oil price and the refined products price, since crude oil represents by far the refiner?s largest cost factor. The relatively low cost of foreign oil means therefore higher profits to those refiners able to process such oil, This applies particularly to integrated companies whose own domestic oil production is insufficient, to meet their refinery requirements but who have developed ample low-cost foreign oil supplies.

Jan 1, 1962

By C. Dirscherl

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71% - as confirmed by real operational data from the Antapaccay mine in Peru. It was the first plant worldwide to use gearless drives for both applications. KEYWORDS: Gearless Mill Drives, Gearless Conveyor Drives, Availability, SAG Mill, Ball Mill, Overland Conveyor, Antapaccay INTRODUCTION – THE GEARLESS PRINCIPLE The principle idea behind a gearless drive system is to reduce the number of components and diversity of parts. Especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material. In order to apply this principle of simplification we will take a look at the components of a conventional drive system consisting of: - Driven equipment (mill, conveyor, slurry pump…) - Components altering the rated speed (gearboxes, girth gear / pinion) - The electric motor - Starting devices for the motor (VSD, CCV, LRS, clutch…), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage - Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation - The electrical supply system (cables, switchgear, transformers, protection equipment) Intermediate gearboxes are not required when a motor is used with a rated speed that directly matches the speed requirement of the driven equipment. Furthermore the VSD can be used to smoothly start the motor and to vary speed during operation, which means that it satisfies both requirements."

Jan 1, 2015

By John M. Moore

Within the Pofadder district of Namaqualand, South Africa, economically exploited deposits of bedded barite and zinc-lead-silver-copper sulfides occur in close proximity within highly metamorphosed mid-Proterozoic pre-tectonic para¬gneisses of the Namaqualand Metamorphic Complex (NMC) (figure i). The paragneisses belong to the Bushmanland Group (SACS, 1980) that comprises a relatively straight-forward regional sequence of basal leucogneisses, intermediate mica-sillimanite schists and glassy quartzites, and a mixed upper zone of banded iron formations (BIF), minor marbles, quartz muscovite schists and localised uppermost quartz-pebble conglomerates and amygdaloidal mafic gneisses (Joubert, 1974) (figure ii). The base metal and barite mineralisation occurs in close association with BIFs, generally above the glassy quartzites, although in some cases possibly below them. In the regional context, the Bushmanland Group paragneisses are, to the north, intercalated with and ultimately replaced by meta-volcanic sequences of talc-alkaline affinity (Reid, 1977) belonging to the Orange River Group (SACS, 1980). The metavolcanics are generally of acidic to intermediate composition and show evidence of subaerial formation from 'high altitude shield volcanism' with many acidic ashflow and welded tuff bands, mesocratic and lesser melanocratic lavas and some fanglomerates (Ritter, 1980). To the south and east, the schist/quartzite associations are initially intercalated with and eventually replaced by cordierite gneiss/metacarbonate/biotite gneiss associations of shallow marine affinity (Moore, 1980a). The Bushmanland Group paragneisses appear to represent sedimentary material in the extreme distal portions of a talc-alkaline volcanic environment adjacent to a shallow platform sea.

Jan 1, 1983

By VIVEK KASHYAP, PATRICK TAYLOR

Zinc ferrite is the major phase component present in zinc refinery residue (ZRR) and electric arc furnace dust (EAFD). Up to 71 percent zinc ferrite has been reported to be present in ZRR, and in most studies zinc ferrite has been deemed the major phase in EAFD. In 2010, the global annual production of EAFD was 3.7 Mt, with 15.20 kg of EAFD generated per ton of recycled steel [1]. The generations of ZRR and EAFD have been growing over time, requiring a greener approach for the reutilization and extraction of valuable elements. ZRR can be a potential source of zinc, as its zinc content is as high as 30 percent [2,3]. The presence of zinc ferrite makes the extraction of zinc difficult because zinc ferrite is refractory to leaching, and direct leaching is inefficient. The Waelz process is currently employed to extract zinc from EAFD and other metallurgical wastes. The Waelz process operates in the temperature range of 1,100 to 1,500 °C and uses coke as reductant. This study explores a carbon-free and relatively low-temperature process for the selective extraction of zinc from pure zinc ferrite.

Never known as a conference to shy away from its share of off-color jokes, the Colorado Mineral Processing Division?s Annual Meeting returned to the Broadmoor Hotel in Colorado Springs, CO April 26-28 for its 62nd edition, this one held under the theme ?Does size matter (is bigger always better).? With the predictable jokes sprinkled in here and there, and a few unpredictable ones as well, the three-day conference featured a healthy mix of talks about some of the latest technical developments in the field of mineral processing, as well as insightful looks at some new operations in the western United States. This year, the Colorado MPD also launched the Wagner Equipment Student Scholarship program.

Jan 1, 2012

By Pratama Mochamad Rizki, Andika Satya

High-risk area in open-pit mining should always be monitored by the operational supervisor because of its nature. One of this type is the soft soil dump area. Due to the unstable bearing capacity of the soil, it’s highly possible for us to find cracks in the area. This paper aims to build computer vision which able to detect truck’s distance from safe limit allowed during dumping activity. The system will warn the truck’s driver if the truck has crossed that predetermined safe limit.

Jun 25, 2023

By John S. Brock

During 1964 and 1965 a mineral exploration program was carried out over an area of approximately 250 square miles, located in the Anvil-Vangorda Creek area of east central Yukon, 125 miles northwest of Whitehorse. The Vangorda deposit, a massive lead-zinc sulphide body discovered in 1953, was centred in the area proposed for exploration, a northwest trending belt located between the southwestern flank of the Anvil Range and Pelly River. Exploration for base metals in the remote Anvil area had previously been restricted by poor metal markets in the late 1950's. Regional geologic information was also limited except for publication of a scale 1 inch to 4 mile map by the Geological Survey of Canada in 1961. To effectively explore this area, a combination of geophysical and geochemical methods were essential due to extensive overburden cover varying in depth from a few feet to over 300 feet. (Figure (i) Key Map) Dynasty Explorations initiated the first comprehensive regional exploration program in the Anvil area, utilizing saturation prospecting methods employing geologic, geochemical and geophysical methods. The program involved an approach demanding continual modification of technical and physical logistics. After a total of 12 months of field work involving an expenditure of approximately $450,00, massive sulphides were discovered which subsequently proved to be an economic orebody. Thirteen properties had been acquired and explored. Ten separate geophysical anomalies had been outlined by a combination of magnetic, electric and gravimetric survey techniques of which five were tested by rotary drilling and two by diamond core drilling. The discovery of the Faro deposit was a direct result of this program.

Jan 1, 1971

By D. M. Carris

Since the Buffalo Creek incident in February, 1972, Federal and state environmental agencies have had the pressure on the coal industry in the Appalachian area to close the coal processing plant water circuits. In an attempt to comply with this requirement, Eastern .Associated Coal Corp. decided to install a vacuum disc filter system at its Kopperston plant to eliminate the tailings pond and reduce the amount of plant make-up water. It was recognized at the time that the plant static thickener tailings would be a very difficult slurry to dewater because of its unusually high clay content. The following is a case history of the Kopperston installation and the refinements Eastern has made in its vacuum disc filter operation to increase efficiency.

Jan 1, 1979

By Timothy J. Orr, Robin J. Burgess-Limerick, Jennica L. Bellanca, MARGARET E. RYAN

Powered haulage continues to be a large safety concern for the mining industry, accounting for approximately 50%of the mining fatal accidents every year. Among these fatal accidents, haul-truck-related accidents are the most common, with 6 of 28 and 6 of 27 fatal accidents occurring in 2017 and 2018, respectively. To better understand why these accidents continue to occur and what can be done to prevent them, researchers reviewed the 91 haul-truck-related fatal accidents that occurred in the USA from 2005 to 2018 and performed bow-tie analyses using the final reports published by the Mine Safety and Health Administration. The analyses explore the context of the accidents with a focus on the initiating event, event outcome, hazards present, and possible preventative and mitigative controls. Overall, the vast majority of the accidents resulted in a haul truck colliding with the environment, and the majority of these events were initiated by loss of situational awareness or loss of control. The majority of the hazards were related to design and organizational controls. The results of this study suggest a need to investigate operator decision-making and organizational controls and to focus on improving design and operation controls such as mine design and operational procedures.

Feb 22, 2021

By B. Samanta

This paper highlights the use of an innovative mine production scheduling scheme for grade-control planning tasks that take into consideration grade-model uncertainty. The scheduling exercise has been carried out with the help of a multiobjective genetic algorithm (MOGa) for the production scheduling operations. The underlying motive behind the use of MOGa has been the generation of a set of pareto optimal solutions to meet the goals of the target-grade specifications for the considered multiple grade attributes. Several new concepts related to MOGa formulation, in particular the mutation operation and the convergence criteria of this algorithm, are proposed in this paper. The modeling of grade uncertainty into the scheduling outputs has also been incorporated through a set of conditional simulated grade maps. The proposed scheme of production scheduling operations has been applied for the grade-control planning operations in an iron ore mine to meet the targeted grade specifications of iron, silica and alumina, and a risk analysis has been performed to this end.

Jan 1, 2013

By Adil Jamali, Taufiq Hidayat, Imam Santoso, Zulfiadi Zulhan, Indah Suryani

The study investigates the segregation of iron and titanium in iron sand concentrate pellets reduced using coal under an isothermal-temperature gradient profile. The results show that metallic iron migrates to the surface while titanium and other oxides move to the center of the pellet. The study provides insights into the reduction process and the behavior of iron and titanium during heat treatment.

Mar 2, 2022

By M. J. dos Santos

"INTRODUCTION In his landmark Society for Mining, Metallurgy and Exploration (SME) 2000 writing, “Theory and Design of Sandwich Belt High Angle Conveyors According to The Expanded Conveyor Technology” J.A. Dos Santos generalized the belt conveyor technology to include all possible variations and augmentations including, particularly, multiple belts along a common carrying and/or return path as is the case most notably in the sandwich belt high angle conveyor technology and belt-on-belt type intermediate (booster) drives. Figure 1, excerpted from his writing, represented the proposition of the generalized “Expanded Conveyor Technology,” abbreviated ExConTec.This formed the basis for the generalization which was completed in theory and in math before 2000 and presented by J. A. Dos Santos at the Y2K SME Annual Meeting. The writing can be found in the SME library (Dos Santos J. A., January 2000). While Figure 1 with the supporting mathematical development solved the generalization, it failed to identify the variation that would prove to have the greatest significance. As with most significant developments, necessity is the mother of invention. This is the case with the Adder Snake belt technology, the subject of this writing. BACKGROUND The concept of elevating bulk materials at a high angle using the sandwich belt concept was first introduced in 1951. That introduction did not produce any lasting success. Commercial success was achieved in the 1970s with the Loop Belt, a sandwich belt elevator of C-shaped profile developed by Stephens Adamson of Canada. The Loop Belt was and is the vital element of a conveyor based self-unloading ship system. Such self-unloading ships have had great success achieving unloading rates above 10,000 t/h with Loop Belts of width to 3,048mm (120”). Being strictly of C-profile, Loop Belts could not be adapted to the general high angle conveying path which is predominantly along a straight incline. It was the success of the Loop Belts that inspired the Dos Santos Sandwich Belts of the 1980s. These expanded the Loop Belt capabilities by producing endless elevating profiles that could take the most direct and/or conforming path between the loading and discharge points. Sandwich Belt high angle conveyor systems have seen great success through the years, with more than 200 installations throughout the world."

Jan 1, 2018

By S. Natansohn

A prevalent technique for the recovery of silver from wastes generated in silver-tungsten electrical contact fabrication is electrowinning. Such scrap is placed in a permeable plastic basket which constitutes the anode compartment and this basket is suspended in a larger cell in which the cathode is mounted. A silver nitrate solution is used as the electrolyte and, upon application of an electric field, the silver migrates to the cathode where it deposits out. At times, there is tungsten migration to the cathode compartment and consequent co-deposition with the silver. This W contamination, which may amount to several thousand ppm, necessitates additional purification of the deposited Ag and its removal would therefore be advantageous. The elimination of the W impurity would also extend the operating period of the cell with corresponding increase in the Ag output and savings in labor costs.

Jan 1, 1982

By Mehmet Ali Recai Önal, MAHMUT CAMALAN

Mineral liberation is one of the primary objectives in comminution circuits for the downstream separation of valuable minerals. Breaking minerals through their grain boundaries (grain-boundary breakage) enables mineral liberation in their natural grain size, removing the need for intensive grinding. This study aimed to evaluate if gaseous carbon dioxide, oxygen, or hydrogen can be used as grinding additives to promote the liberation of chromite grains by grain-boundary breakage. For this purpose, chromite ore particles in the −9.53 + 6.35 mm size fraction were pretreated by exposing them to carbon dioxide, oxygen, or hydrogen flow. Then, the untreated and pretreated samples were broken in a drop-weight tester under the same conditions. Finally, the graderecovery plots of chromite grains in the selected progeny size fractions and the overall progeny distributions were measured and compared. Pretreatment with carbon dioxide flow was found beneficial for grain-boundary breakage. It significantly enhanced the liberation of coarse chromite grains along with the overall progeny fineness. EPMAanalysis showed that the adsorption of carbon dioxide seems to reduce aluminum concentration at grain boundaries, which could be the reason for grain-boundary weakening. These results suggest that carbon dioxide can be used as a grinding additive, reducing the carbon footprint of the mining industry.

Oct 29, 2020

By TUIJA MONONEN, LUDGER BENIGHAUS, CHRISTINA BENIGHAUS, Virginia del Rio, SARI KAUPPI, JUHA M. KOTILAINEN, JAVIER GÓMEZ, JARI LYYTIMÄKI

The understanding of public debates over mineral exploration and mining largely originates from exceptional situations such as mining accidents of conflicts. Less is known about how mining is portrayed and understood under more conventional settings. What storylines dominate the local day-to-day public debate? This article presents results from a comparative case study focusing on newspaper coverage of mineral exploration and mining in three European countries representing different geological and socio-economic contexts. Newspaper articles from the Geyer-Erzgebirge region in Germany, the Andalusia region in Spain, and Northern Finland are studied. The sample looks into the period between September 2018 and February 2020 and shows that regional newspapers report about mining issues relatively intensively even in the absence of major accidents or other media events causing peaks of attention. The tone of the articles is generally neutral to positive towards mining activities, reflecting the specific local settings, historical experiences, and future expectations. Despite the different contexts of the three countries, there were considerable similarities to the topics highlighted, including common themes of mining revival, mining events and social interaction, history of mining, and damages related to mining. Past, present, and future employment opportunities related directly or indirectly to the mining sector are key storylines. Another recurrent underlying theme is the need to balance environment and safety risks and socio-economic prosperity, typically covered through ordinary disputes among the mining sector, public authorities, regional non-governmental organizations, and local initiatives.

Jul 6, 2021

By Jurgen H. Kleinau

This paper details Keeler/ Dorr-Oliver's experience with the application of fluid bed combustion technology to the burning of coal-mining waste. The designs of two stage fluid bed combustors/dryers are demonstrated as useful in the drying of coal, slag and coke, using coal and coal refuse (gob) as fuel. Anthracite mining refuse (culm) is more than abundant in Northeastern Pennsylvania. After demonstration at Shamokin, Pennsylvania, a full commercial-sized fluid bed boiler using culm is used for district heating in Wilkes-Barre, Pennsylvania. Limited research work has shown the utility of using fine coal as filter aid in sludge in¬cineration. With the rising avenues of the suitability of coal as auxiliary fuel in fluid bed sludge incineration, an expansion of these concepts combines the use of coal or coal refuse as filter aid and auxiliary fuel. Lime¬stone addition controls SO2 emission.

Jan 1, 1985

By K. S. Fraser, R. Frischmuth

High temperature pressure oxidation (>190°C) is a wellrecognized and versatile metallurgical oxidative pre-treatment process commonly used to liberate gold from refractory sulfide ores and concentrates. The pressure oxidation of refractory gold ores was first commercially applied in 1985, at Homestake Mining Company’s McLaughlin mine in the United States. Since that time numerous refractory gold and other high temperature pressure oxidation facilities have been built throughout the world. The design of each facility was met with unique challenges and opportunities which have led to an array of plant configurations, pressure oxidation autoclave sizes, and sulfide oxidation capacities. This paper presents a historical review of high temperature pressure oxidation operations and current projects in execution with a focus on the autoclave vessel design, circuit configuration, and unit sulfide oxidation capacity as a basis for characterization and comparison.

Mar 2, 2022