Search Documents

By E. M. Abraham

The establishment and survival of different grass species and cultivars on various phytotechnic treatments at a limestone quarry was studied. The treatments applied were: a) bare soil, b) bentonite, c) bentonite-straw and d) asphalt-straw. According to the results, significant differences were found among species and cultivars, growing on different treatments as far as plant growth and survival are concerned. The seed germination was higher on bentonite -straw and asphaltic-straw than on bentonite but the plants survival were higher on bentonite. Lolium perenne had higher seed germination rate and better establishment than the other tested species at all treatments. However, the survival rate of Agropyron desertorum and of the cultivars palestina and chrysopigi of Dactylis glomerata was higher than of the other species.

Jan 1, 2007

By C. P. Mangelsdorf

Introduction The use of frequency of vibration measurements to determine tension has long been accepted by industries that use electrical or stranded cables of wire ropes in their operations. In contemplating how to determine the tension in chords of a roof truss, it seems almost inevitable that a similar approach should be investigated even though there are some important dissimilarities in physical behavior between a chord of a rod-type Birmingham truss and a stretched wire rope. While the dominant feature of both types of behavior is the existence of tension, the bending resistance of the vibrating truss chord cannot be ignored. And it is common to have attached to the chord, pieces of hardware (turnbuckles, extension sleeves, wedge boxes) that represent concentrations of mass not usually found in a vibrating wire rope. Analytical solutions to the problem of vibrating wires or beams can be found in the literature on vibrations (Timoshensko, 1955; Den Hartog, 1956). But in every case, at least one of the ingredients of the vibrating truss chord is missing. The presence of axial tension, or bending resistance, of concentrated masses and of end conditions peculiar to truss chords is a combination that appears not to have been dealt with before, although the techniques for dealing with it are commonly known. The purpose of this note is to report the results of a project to measure and calibrate such frequencies. The work was conducted by the University of Pittsburgh under the sponsorship of the US Bureau of Mines. Field observations Tests were conducted on 24 different truss installations. The first 18 trusses were installed in shale roofs above Kentucky No. 9 seam and Illinois No. 6 seam. The remaining six were placed against the competent sandstone over the Pocahontas No. 3 seam in West Virginia. Chord tension was determined by two electrical resistance strain gages, in series, applied diametrically opposite to one another on the rod before tensioning. Due to the combined effects of inexact gage placement, rod bending and residual torsion in the chord due to tightening, errors in tension as high as 1780 N (400 lb) were reasonably possible. Due to faulty soldering or damage, three of the first 18 trusses and one of the final six were rendered completely unreliable. In addition to strain, the first natural frequency of vibration was observed to the nearest 0.1 Hz. Dimensions recorded included the span between contact points at the bearing blocks (Fig. 1) and the locations and amount of excess rod and rod gap at the wedge box and turnbuckle, respectively.

Jan 9, 1985

By Daniel Tao, Jike Qiao, Hao Ren, Feifei Ji, Gonglun Chen

The floatation of niobite was studied using a number of collectors at various dosages and solution pH’s. Octyl diphosphonic acid was found to be an effective collector for niobite flotation with good selectivity. A flotation recovery of 91.2% was obtained with 140 mg/l octyl diphosphonic acid at pH’s less than 5.0. Infrared absorption spectroscopy (IAS) and X-ray photoelectron spectroscopy (XPS) were used to characterize the interactions of niobite with octyl diphosphonic acid. Species distribution diagram of octyl diphosphonic acid and niobium species was used to elucidate the flotation behavior of the mineral with octyl diphosphonic acid. A chemical adsorption mechanism of niobite with octyl diphosphonic acid was proposed. Keywords: octyl diphosphonic acid, electrokinetic measurements, niobite flotation, XPS.

Jan 1, 2005

By Y. Breau, F. Robichaud

The Expert System implemented at the East-Malartic mill controls a copper flotation circuit while taking into account the profitability of the operation. Treating a copper gold ore, the flow sheet integrates a flotation step followed by cyanide leach circuit. The Expert System calculates the actual net smelter revenue of the flotation circuit, accounts for the operating cost of the cyanidation circuit and defines optimal metallurgical operating targets to optimize the overall economics. To be realistic, probability factors and circuit diagnostic analysis are integrated in the operating target selection. The Expert System has proved to be successful, robust and flexible. It resulted in a copper concentrate grade increase of 1% while maintaining recovery. The use of the expert system also gives plant personnel good training procedures and promotes interaction with mill operator.

Jan 1, 2002

By R. L. Virta

Twenty-three companies mined kaolin in nine States in 2004. Production was estimated to be 7.6 Mt (8.3 million st) valued at $912 million, based on preliminary data. This was a slight decrease from 7.68 Mt (8.46 million st) valued at $939 million in 2003.Georgia was the leading producer state with an estimated 6.5 Mt (7.1 million st) in production. It was followed, in decreasing order of tonnage, by South Carolina, Alabama, California, Texas, Arkansas, Nevada, Florida and North Carolina. Georgia accounted for nearly the entire domestic water-washed, delaminated, and pigment-grade calcined kaolin production. Consumption Sales to the paper industry accounted for 49 percent of domestic sales and 64 percent of total sales. Other major markets for domestic sales were refractory products (10 percent), paint (5 percent), fiberglass (4 percent), catalysts (3 percent) and rubber (2 percent).Paper coating and filler markets accounted for about 87percent of export sales of kaolin.

Jan 1, 2005

By E. Tulcanaza

M.S. Azun I do not at all agree with the basic points of the author's conclusion. The use of lognormal or normal model to respond to the attribute distribution function should be carefully questioned. If fitting a distribution function of regionalized variables is the main purpose, one may employ one of certain well-known families of distributions, such as Tukey's lambda functions. For instance, the distribution function of gold assay values studied by Krige (Krige, 1978) may fit the lognormal model well, but one should not exclude that the basic idea of using the distribution function of observed data is to have insight of the physical mechanism that gives rise to the regionalized variables. In Applied Geostatistics, there are many examples considering only lognormal or normal model for the distribution function of geostatistical data even if the observed distribution function has more than one mode. Of course, using lognormal or normal model always brings easy computation for the statistical properties of attribute under investigation. Still, I object to adopting any of those models without having any "statistical inference." As seen from the author's paper, lognormal and normal model produce the same average grade (0.746% copper) and almost the same sample variance. Therefore, which model explains the probabilistic behavior of ore deposit is always an important question that should be replied by the geostatistician using not the common sense but the statistical and probabilistic methods. For kriging procedures, such as linear kriging, one should describe either second order stationary properties or bivariate properties of regionalized variables. Second order properties, such as correlogram function or semivariogram function, are the inputs of the so-called kriging equations. Selecting one of any useable models for the observed second order properties, such as spherical model, is not easy since the models are not based on the correlations structure of the regionalized variables. How those models being used in Applied Geostatistics can be distinguished is another important problem. One may develop many fitting models to respond to the observed second order properties of regionalized variables. However, I suggest that the model should be based on the probabilistic behavior of geologic process. The author used spherical model for copper, wolfram, and silver grades from isotropic sector (Fig. 2, 4, 3b) and exponential model for silver grades obtained along raises in isotropic sector (Fig. 3a). It seems that those semivariograms given in Fig. 3b for isotropic sector and Fig. 4 may be described by the random model implying that regionalized variables do belong to renewal process (Azun, 1983). If I knew the total number of data points used in estimation, I may prove that my conclusion is correct. Recalling the test for the first order sample correlogram value, the test procedure is introduced such that the independence is rejected if [ ] where Za/2 is the a/2 percentile of standard normal random variable and N is the total number of samples used in estimation (Azun, 1983). For the other observed semivariogram functions I suggest the author might try to use the so-called "Markovian model" describing not only the correlation structure of regionalized variables, but also the physical mechanism that produces the regionalized variables. The Markovian model for correlogram function is, [ ] The Markovian model for the other second order properties of ReV are also derived. T ve B, in the above equation, show, for example, structural change and mineralizational variation in a considered deposit, respectively (Azun, 1983). In selecting any model, it is not easy to search for the "best" response to the observed second order properties of ReV's. The Markovian model, based on a theoretical understanding of underlying mechanism, gives more information about the occurrence of regionalized variables and respond to all properties. Random model and the so-called hole effect structure can be easily defined as a special form of the Markovian model (Azun, 1983). An estimation of any second order properties of regionalized variables may be computed through (N-1) lag. However, the dependency between the regionalized variables may be deemed to have "died out" after the so-called stationarity width (range). In practice, the estimation is carried out through 25% of the total number samples available. Therefore, the large fluctuations around the zero level and variance for correlogram or covariogram function and semi-variogram function, respectively, cannot be observed. Since the number of pairs involved in the estimation of higher second order properties is small, the estimation variance at those lags is large. There is no need to show higher order estimated second order properties. After using one of any kriging procedure for block estimation, the distribution function of average grades has the same mean as the drilling sample grades but

Jan 3, 1985

By Z. Zhang, R. G. Reddy

Viscosities of industrial lead slags with various compositions were measured as a function of temperature using a Brookfield viscometer. Based on the experimental data from this study and other investigations reported in the literature, an expression has been developed to correlate the viscosities of lead silicate slags as functions of composition and temperature. The effect of each individual slag component on the variation of the slag viscosity is identified. The composition dependency of viscosity of lead silicate slags is discussed. The calculated results using this viscosity expression are in good agreement with the measured data.

Jan 1, 2001

By L. A. Weakly, D. A. Weiss, R. B. Crookston

A presentation of experience gained from using mechanical and conventional equipment for excavating shafts, raises, tunnels and other openings in various Colorado oil shale mining properties.

Jan 1, 1983

By M. Wiber, P. Nicoll

Rio Algom has embarked on a major programme of expansion with the goal of becoming one of the world’s top-performing base-metal mining and metals distribution companies. To assist the company and its operations in achieving its business objectives, we are implementing an environment, health and safety (EHS) management system, built to be compatible with the 14001 model. We recognize that a sustainable development approach for Rio Algom includes outstanding performance in EHS and community responsibility and is essential to earn acceptance within the communities where we operate or wish to locate; raise capital; obtain permits, and operate efficiently. We are committed to triple bottom line accountability, i.e. full consideration of environmental, social and economic concerns in our business decision making.

Jan 1, 2000

By K. Burke, K. L. Myers, R. Espell

Barrick Goldstrike’s (Goldstrike) AA Heap Leach Pad is an HDPE lined facility used for gold recovery from low grade ores using conventional cyanide heap leach technology, operated from 1987 through 1999. Goldstrike prepared a unique reclamation plan for the AA Leach Pad Facility to provide for a cost-effective, environmentally sound facility closure and to fulfill the State of Nevada’s closure requirements. Traditional Nevada leach pad closure has involved rinsing to reduce cyanide concentration to an acceptable level, followed by reclamation. However, certain metals and compounds are not typically reduced by rinsing and some constituents may increase in concentration with rinsing. A closure scenario to effect limited infiltration through installation of a capillary cover for the leach pad was developed. The capillary cover was constructed by placing a fine-grained layer above the coarse-grained spent leach material to create a capillary break. In an arid climate such as Nevada, the fine-grained layer will rarely reach full saturation and the cover will be able to store water during precipitation and allow removal of water through evaporation and transpiration (ET) during the growing season. A 1.22 m (4 ft) cover thickness was selected as the optimum design cover thickness. The drainage network on the surface of the re-contoured AA Heap Leach Pad was specifically designed to enhance the revegetation, reclamation, and sediment yield control aspects of the AA Heap Leach Pad closure, while resulting in a natural looking surface, compatible with the surrounding topography. Adjacent natural topographic features were used to establish target design parameters for re-contouring and erosion control design.

Jan 1, 2001

By Rees D. Groves

Cement copper is ordinarily converted to marketable metal by processing in a conventional smelter and refinery. Because of rapidly increasing cement copper production and limited excess smelting capacity, other techniques were investigated for preparing marketable copper products. One route was to make copper powder for industrial use. The process scheme employed flotation for rejecting the bulk of the impurities, acid leaching to remove residual iron and aluminum, reduction sintering to eliminate oxygen, and grinding to obtain powder. Another route was to sinter the floated and leached copper into the form of anodes and electrolyze these to yield refined copper cathodes. At a current density of 30 amperes per square foot, power consumption for electrorefining was 185 kwhr per ton of copper. The feasibility of preparing commercial-size anodes by sintering is still to be assessed.

Jan 1, 1970

By J. A. Botín

NPV is a static measure of project value which does not discriminate between levels of internal and external risk in project valuation. Due to current investment project?s characteristics, a much more complex model is needed: one that includes the value of flexibility and the different risk levels associated with variables subject to uncertainty (price, costs, exchange rates, grade and tonnage of the deposits, cut off grade, among many others). Few of these variables present any correlation or can be treated uniformly. In this context, Real Option Valuation (ROV) arose more than a decade ago, as a mainly theoretical model with the potential for simultaneous calculation of the risk associated with such variables. This paper reviews the literature regarding the application of Real Options Valuation in mining, noting the prior focus on external risks, and presents a case study where ROV is applied to quantify risk associated to mine planning.

Jan 1, 2012

By J. L. Hoover

The goal of the drill bit consumption study was to develop an equation(s) based on various components that affect bit drill wear and use the equation(s) to estimate the consumption of bits during production drilling. Drill bit data from various geographic locations were compiled and used to develop linear regression equations using the Microsoft Excel Software. Multiple drill bit consumption equations were developed and statistical analysis was used to verify the accuracy of those equations. The equations will allow mining companies to more accurately forecast drill bit consumption when evaluating new mine properties. This capability becomes increasingly beneficial to forecasting as the cost of consumables increases.

Jan 1, 2012

By G. Bourque

Early in the design stage of their new concentrator for the Mount Wright Plant, Quebec Cartier Mining decided to use a process computer for total control of crushing, grinding and concentrating. A map of the area is given in figure 1 and a view of the plant in figure 2. Although the use of process computers is not a new idea in petrochemical and chemical industries, their use in the mining industry is very limited. We innovated in using the computer, not only for data logging, as we have seen in some other plants, but a sole operator located in the administration building, starts and stops mill lines, crushers, load-out system, tailings, thickeners, etc ... by means of a CRT console. Our process is fairly simple as can be seen on the schematic process flow diagram (figure 3). .The ore, carried by 136t diesel electric trucks, is dumped through ore pockets onto two primary pan feeders. The feeders supply two 1,52mx2,79m gyratory crushers which reduce the ore to minus 20,32 cm. Each crushing line have a capacity of 5600t per hour and feed a shuttle conveyor distributing the crude ore into six silos.

Jan 1, 1979

By G. J. Joy

Although rates of pneumoconiosis in coal miners have declined substantially in the United States since the passage of the Federal Coal Mine Health and Safety Act of 1969, new cases continue to occur, including cases of rapidly progressive disease. In contrast, Australia?s underground coal mining industry has reported few new cases of pneumoconiosis for over twenty years. Mortality from Coal Workers? Pneumoconiosis in official health statistics and the prevalence of pneumoconiosis among miners screened in x-ray surveillance programs are also lower in Australia. To understand this disparity, the National Institute for Occupational Safety and Health was requested by both industry and labor stakeholders to examine this issue, with the ultimate aim of reducing the rate of pneumoconiosis among United States coal miners. A number of factors, including coal dust exposure, silica exposure, and coal rank were examined as potential contributors to the above observed differences. Comparison of coal rank data from each country did not show any significant differences. Air sample data from the coal mining industries in both countries show that coal dust levels in Australian mines are somewhat higher than those reported in similar U.S. mines; however, quartz exposure for Australian miners is lower than for many U.S. miners. Assuming that quartz is contributing to the greater number of cases of advanced pneumoconiosis in the U.S., more effective dust control measures, as well an independent exposure standard for respirable quartz in coal mining, need to be implemented to prevent this potentially disabling condition.

Jan 1, 2011

By S. L. Lebo, J. D. Gargulak

Lignin, the second most abundant natural polymer and bi-product of the pulp and paper industry, has been commercially available in a number of forms since 1940. This growing industry is fueled by demand in traditional applications. Reagents that offer unique solutions in various mineral process applications are examples of advanced uses that also fuel growth. These applications include flotation reagents in fluorspar, bastnäsite and potash, as well as in the zinc pressure leach process. Due to the fact that no concerted effort has been made to find applications for modified lignosulfonates, it is quite possible that this natural material will find use in other benefication processes.

Jan 1, 2002

By G. C. Hall, B. E. Hobbs

Giant gold deposits are considered products of crustal-scale systems. Reduced fluids stored in mid to lower crustal reservoirs were discharged into mid to upper crustal sites of deposition. Elements of the architecture include crustal-scale structures, reduced packages of rock and regional seals. Gas-rich aqueous fluids were common but non-aqueous fluids may have been significant in the deeper parts of the systems. Fluid fluxes in over pressured domains were maintained by porosity waves. Abnormal heat input from the mantle may not be required once the systems were perturbed. Fluid-mixing and hypogene enrichment were probably the most significant precipitation processes.

Jan 1, 1999

By V. T. McLemore

The mining industry is at a crossroad. To sustain our technically based society, demands for commodities are increasing, and exploration for these commodities is a must. The debate is between sustainable development and the status quo and begins with exploration, where it is determined if a mineralized area contains enough potential ore to be mined economically. Mineral deposits are relatively rare and depend upon certain natural geologic conditions to form and may not always occur in locations that are most suitable to society. Exploration can be compatible with environmental protection and social responsibility, but difficult challenges face the industry to develop a property that is environmentally, economically, and socially responsible.

Jan 1, 2004

By Earl Rau

Introduction Will cogeneration be a major power source in the future? The location of electric power generating plants has changed. In 1900, more than 50% of electricity was generated by industrial plants. Since then, industrial plant generation of electricity greatly decreased to 17% in 1950 and to only 3% in 1980. Changing economics in electric power generating costs, though, may allow cogeneration to reverse this trend. Cogeneration has been defined as the simultaneous production of electric (mechanical) and thermal energy from a single energy source. Some applications are considered to be byproduct generation of electricity from industrial, thermal operations. Cogeneration is not new to the mining and minerals industry. Smelters and steel mills have used waste heat to generate electricity. Public Utilities Regulatory Policies Act of 1978 The potential for increased industrial cogeneration of electricity is related to the March 9, 1978 enactment of the Public Utility Regulatory Policies Act (PURPA). The US Supreme Court ruled that PURPA is constitutional. The court upheld requirements that utilities interconnect to cogenerators. It also ruled that 100% of avoided costs be used as the guideline for electricity sales by a qualifying facility (QF) to a utility. The state of New York established a floor price $0.06/kWh for electricity sales from a QF to a utility. It is obvious, then, that a cogenerator must first establish price and then become a qualifying facility in order to sell electricity to a utility. Proposed cogeneration plants The estimated industrial cogeneration potential for the years 1986 to 2000 is 9500 to 25,000 MW. Industries represented in this cogeneration estimate are pulp and paper, petroleum, chemicals, food, textiles, rubber, plastics, steel, lumber and wood, cement, glass, metal fabrication, and industrial parks. A cogeneration plant has been proposed for the Union Carbide chemical plant in Institute, WV. A steam turbine/generator would be installed to replace the pressure-reducing valve in the 2.7 MPa (400 psig) header. Scott Paper Co., Mobile, AL, proposed a cogeneration plant using a coal- and wood-fired boiler and a turbine/generator to produce process steam and electric power. A cogeneration system has been proposed for a large oil refining plant. A pulverized coal boiler would produce high-pressure steam to operate a turbine, generator. The exhaust steam from the turbine will go to the process and an existing turbine. Kansas City, MO's Armour meat-processing plant has proposed a cogeneration plant. This proposal is to use a natural gas or oil-fired, gas-driven turbine and a generator. The waste heat from the gas turbine would go to a heat recovery boiler for use as process heat. Dade County, FL is implementing a central energy system to supply electricity, air conditioning, and domestic hot water for five buildings in downtown Miami. The cogeneration system is to provide flexibility, to optimize fuel use efficiency while serving the variable thermal demands. Generation of electricity from municipal waste is not considered to be a cogeneration process but is covered by PURPA. Special considerations are provided for waste/electric power generation to encourage the development of these systems. ?

Jan 7, 1987

By Stanley C. Suboleski

1977 was the modern day low point for productivity in the coal industry. At that time, no one could have predicted that the industry was about to enter a productivity rise that would continue unabated through the 1980s. Thirteen years later, the cause of this phenomenon is still not well understood. While many government studies focused on the fall in productivity from 1969 to 1977, none have been undertaken to explain the rise. Some of the likely causes of the gain in productivity during this period will be discussed here. An attempt will also be made to quantify the value of some of the technical innovations that have taken place. The remainder of the gain is assumed to come from non-technical sources. The nature of these sources, although largely non-quantifiable, is also discussed. Since the number of mines that have adopted the technical innovations noted here is largely unknown, the actual contribu¬tion of technological changes to the overall productivity gain can only be estimated.

Jan 1, 1990