Search Documents

By Louis A. Panek, John A. Stock

A flat slot is created in rock to cause stress relief effects in a pair of hydraulic borehole pressure cells (previously installed in drill holes above and below the slot ) , which act as sensing devices . This relief is annulled by repressuring the slot by means of a flat hydraulic cell . The slot pressure at annulment is taken to be the existing ground stress at right angles to the plane of the slot . A number of trial installations in the rib of a mine drift showed that for a valid determination of ground stress the sensing devices that respond to relief and repressuring must be within a specified zone close to the pressure transmitter ; otherwise the indicated ground stress may be excessive . By using an additional pair of borehole pressure cells , installed a few feet away , the existing rock stress can be redetermined at intervals , irrespective of a change of stress intensity subsequent to the initial installation . Based on these findings , equipment and procedures have been developed that make possible the installation and operation of a permanent rock stress monitoring station for observing mining - induced stress changes . The station consists of a 12 - in - wide hydraulic pressure cell cemented in a flat slot and four 2- by 8 - in flat hydraulic pressure cells in nearby drill holes . All drilling for the installation can be done with an air leg drill and conventional bits . Once the installation is completed , all required information is obtained by Bourdon pressure gage readings . The apparatus is simple , relatively inexpensive , and reliable under operating conditions in a wet mine . Unlike most methods of rock stress determination , this scheme permits periodic remeasurement of absolute rock pressure over several years , without additional drilling or instrumentation . Similar to other flat slot procedures , stress measurements are obtained without making auxiliary tests to determine elastic

Jan 1, 1964

By W. G. Messner

Pipelines for transporting crude oil and refined products in the United States totaled 189,982 miles on January 1, 1959. This mileage was less than a 1-percent increase from the 1956 total of 188,540 miles. During the three-year period (January 1956 - January 199), 14,886 miles of new pipe and 10,649 miles of secondhand pipe was laid. Pipe taken up in the same period was 24,093 miles. The facts regarding pipeline mileage were obtained by the Bureau of Mines from pipeline companies and information provided by the Interstate Commerce Commission. Crude-oil gathering lines, as of January 1959, were 40 percent of the United States pipeline mileage and totaled 75,182 miles, an increase of 1,656 miles during the three-year period. Crude-oil trunklines totaled 70,317 miles or 37 percent of the United States pipeline mileage, a decline of 8,277 miles from the 1956 total. Some of this loss is attributed to the converting of crude lines to refined products. Refined product lines in January 1959, totaled 44,483 or 23 percent of the United States mileage, an increase of 8,063 miles during the three-year period.

Jan 1, 1959

By Wilton Johnson

Native asphalt was produced in 1981 by five companies in three States, Alabama, Texas, and Utah. Texas was the leading State in production of native asphalt. Total production increased in 1981 to 1.26 million tons, while value increased 10.5% to $27.7 million. Bituminous limestone, used primarily for street and road repair, was produced by Whites Uvalde Mines and Uvalde Rock Asphalt Co., both in Uvalde County, Tex., and Southern Stone Co., Colbert County, Ala. Gilsonite was produced by American Gilsonite Co., Uinta County, Utah, and Ziegler Chemical and Mineral Corp., Weber County, Utah. This material was used for purposes other than road repair.

Jan 1, 1982

By Gregory J. Chekan

The Bureau of Mines, in an effort to improve planning and development in coal mining, is investigating strata interactions associated with mining of multiple coalbeds. Two common interactions that occur between adjacent coalbeds are subsidence and pillar load transfer. The study described involves underground observations and measurements conducted at two Pennsylvania mines, each affected by one of these interactions. At the mine affected by subsidence, measurements show that undermining had little effect on upper mine pillar stability, but had a more severe effect on the development and maintenance of entries. Roof-to-floor measurements recorded over four times more convergence in entries developed over gob as compared with entries developed over support pillars in the lower mine. At the mine affected by pillar load transfer, Initial in situ measurements have shown the existence of a pressure arch in the lower workings. Prior research has shown that arch interaction between two adjacent openings can create stress concentrations in the in-nerburden. Underground measurements and results obtained from both mine sites correlate with theoretical and photoelastic multiple-seam models, and eventually these field data will serve to refine model accuracy. Further study of multiple-seam interaction mechanisms will lead to improved mine planning, increased resource conservation, and a safer working environment.

Jan 1, 1986

Confidence in the strength of the U.S. economic recovery was considerably enhanced by third quarter 1983 profits, which showed a 12.8-percent increase over those in the second quarter (table I). Although the increases were not as great as between the first and second quarter of 1983, profits have grown each quarter since fourth quarter 1982. Both total profits and profits per unit of output increased, which the Bureau of Economic Analysis (BEA) attributes to decreases in labor and nonlabor costs (per unit of output), as well as to moderate price increases. [ ] A number of durable goods sectors, however, continue to show profit declines, especially electrical and non-electrical machinery. Profits in the primary metal industry are still negative, but the economic picture of this industry is improving. Between the second and third quarters of 1983, capacity utilization increased somewhat in primary metal manufacturing and stone and earth mineral mining but did not change at all in metal mining. Capacity utilization in metal materials increased from 47.4 percent in the fourth quarter of 1982 to 64.2 percent in the third quarter of 1983 (table 2).

Jan 1, 1983

By H. P. Greenwald, H. C. Howarth

There was reported in Bureau of Mines Technical Paper 5754/ a series of tests to determine the compressibility and bearing strength of specimens prepared from blocks of potash salt obtained from a mine near Carlsbad , N. Mex . The events leading up to the investigation were sketched in a foreword by George S. Rice , then chief mining engineer of the Bureau ( retired September 30 , 1937 ) ; this foreword also gives a discussion of the possibility of increasing the ultimate total recovery of the potash salt by " second mining" of pillars or by use of a longwall system . In June 1936 , Rice and the senior author visited Carlsbad with H. I. Smith , chief of the mining division of the Geological Survey , to observe mining then in progress and to discuss with the management of one of the mines records of convergence of roof and floor which they were obtaining . It developed that serious thought was being given to the possibility of roof failure resulting from shear at the faces of pillars . There was envisioned the danger of such cracks extending upward to water - bearing strata . Obviously , the simple compression tests of the potash salt then being made would throw no light on this question , and tests of assemblies of potash and roof salts would have to be made . In this connection it is to be remembered that in the mine no sharp division exists between the potash salt being recovered and the nearly pure halite which forms the roof . The interlocked crystalline structure is continuous , and there is merely a very rapid decrease in the proportion of sylvite in a short distance vertically . Figure 2 of Technical Paper 575 shows that two samples near the top of the salt being mined contained , respectively , 51 and 65 percent potassium chloride . Contrasted with this is an analysis of the roof salt given on page 24 of that publication , which showed only 3.6 percent potassium chloride . As the data given in Technical Paper 575 show , the roof salt is much less plastic than the potash salt . The immediate roof may then be thought of as a more rigid stratum of indefinite extent resting on and continuous with yielding supports and loaded uniformly at the rate of 900 to 950 pounds per square inch . Just what thickness of the salt should be considered as immediate roof is uncertain .

Feb 1, 1938

By J. H. Wiggins

The evaporation of crude oil without doubt causes one of the largest single losses to which the oil is subjected after it is taken from the ground. The few days during which crude oil is stored on the lease before being taken by the pipe line, causes an aggregate loss per year from evaporation estimated at 122,100,000 gallons of gasoline in the Mid-Continent field alone. This has a value, at 22 cents per gallon, of $26,880,000 and represents about 3 per cent of the total gasoline produced in the United States from all fields and all sources. The following table shows this in more detail:

May 1, 1920

By Wilbur A. Haley

One of the purposes of the investigation was to determine and report on how coal augers are used to mine bituminous coal that is near outcrops and may not be mined otherwise by any other present-day method. Such increased overall recovery results in the conservation of coal resources. Other reasons for the investigation were to determine and report the production rates of such operations and the types of equipment used. Auger mining of coal as a means of coal recovery supplementary to strip mining has been introduced and developed since World War II. This type of coal mining has grown rapidly, and bituminous-coal production by auger mining has been estimated at 6,000,000 tons in 1955. Mines were selected for study to give reasonably representative information on auger mining in different types and thicknesses of coal beds in different geographic areas and on different types and sizes of equipment operated under various conditions. This report is based on field studies of 8 auger-miming operations in Pennsylvania, West Virginia, and Ohio and in 5 different coal beds. Operations were observed in active strip mines, in strip mines reopened for auger mining, and along benched coal-bed outcrops. At the time of this study, no augers were reported to be operating in underground mines. The diameters of holes drilled ranged from 26 to 52 inches, and the lengths of holes ranged up to 208 feet. At some operations auger holes often penetrated abandoned underground mine workings.

Jan 1, 1957

By Roy L. Grant

The Bureau of Mines investigated the up-and-down method with factorial designs to determine if shorter, and therefore less costly, trial sequences could be used. Although sequences of 50 trials are usually recommended, sequences of 20 trials were arbitrarily chosen for the experiments with permissible coal mine explosives described in this report. These explosives were fired from a cannon pointed into a flammable natural gas-air atmosphere at the Bureau of Mines Explosives Research Center gallery to ascertain their safety properties. The investigation demonstrated that the shorter sequences led to useful conclusions with a reduction in cost of the experimental program.

Jan 1, 1967

By B. D. Nash

The Bureau of Mines continued its research into the recovery of fluorine by the phosphoric acid acidulation defluorination of phosphate rock concentrates. A small process development unit with a capacity of about 10 kilo-grams of charge per hour was operated, and concentrates from both Idaho and Florida were processed. Over 80 percent of the fluorine was evolved and recovered as a dilute fluosilicic acid solution. Phosphate extraction from the concentrates always exceeded 98 percent. The fluorine was converted to a synthetic fluorspar product (3CaFa?SiOa) suitable for use as a slag conditioner in electric furnace steelmaking operations.

Jan 1, 1977

By Charles A. Seitz

This Bureau of Mines report describes a chromatographic method for analyzing impurities in helium that utilizes a helium carrier gas contain-ing 25 to 30 ppm Ne. An example of the effect of trace amounts of nitrogen, methane, and moisture on the detector's response is shown. The added neon in the carrier does away with irregularities of the analysis which were experienced when the carrier contained up to 3 ppm Ne. The addition of 25 to 30 ppm Ne causes a loss of sensitivity, but the re-maining sensitivity is adequate for routine analyses. The high-neon carrier allows positive and more linear responses for eight impurities: neon, hydrogen, argon, oxygen, nitrogen, methane, carbon dioxide, and ethane. Neon concentration levels of 0.02 to 125 ppm in helium carrier gases were studied. The high-neon carrier has been in successful rou-tine use in Bureau of Mines helium facilities since October 1981.

Jan 1, 1985

By Paul M. Tyler

According to Lindgren , the economic importance of pegmatites stems from the fact that they represent the principal natural storehouse of two classes of mineral products : (1 ) common minerals in exceptional size and purity and ( 2 ) several of the rarest minerals , which are not commercially available from other types of deposits . Most pegmatites can be described simply as coarse- to very coarsegrained granites . Pegmatite includes coarse -textured igneous rocks of any composition , such as syenitic , alkali syenitic , dioritic , or gabbroitic ; but basic pegmatites are far less common than those that are associated with acid rocks and correspond approximately to the mineral composition of ordinary granite . Moreover , only a very few basic pegmatites can be considered as economic sources of useful minerals . Whereas , in ordinary granitic rocks the individual minerals usually measure 1/8 to 1/4 inch across , in pegmatites they are characteristically over 1 inch and often more than 12 inches in diameter . Although some of the constituents of the pegmatite may be only a fraction of an inch in length , single crystals more than 10 feet long are by no means unusual , and some crystals are enormous . A whole quarry was operated in the Urals within a single crystal of feldspar . Huge quartz crystals are quite common although usually imperfect . Muscovite plates 10 feet in diameter have been mined in India , and the Purdy mica mine in Canada contained a mica crystal measuring 6.5 by 9.5 feet and weighing nearly 7 tons , which supplied more than $20,000 worth of trimmed mica sheet . A loglike crystal of spodumene in the Etta mine in the Black Hills of South Dakota was 42 feet long . Giant crystals of beryl weighing several tons apiece have been mined from several properties . Because so many rare minerals are found in substantial concentration only in pegmatites , it is a common fallacy to suppose that pegmatites are always enriched in rare elements . Traces of most of these elements , of course , are found in almost all igneous rocks , and they reappear in the sediments derived from igneous rocks . It does not follow , however , that all or even most pegmatites contain higher percentages of rare elements than other granitic rocks . Geological evidence points to the probability that notable concentrations of rarer minerals or elements in pegmatites are more or less fortuituous , such additions often being ascribed to events subsequent to the original emplacement of the main body of the pegmatite . Most pegmatites consist principally of potash , feldspar , and quartz . Even mica , although commonly present , is not an essential constituent . Probably

Feb 1, 1950

By Khamis Y. Haramy

This U.S. Bureau of Mines report describes the use of Bureau-developed flat and cylindrical hydraulic borehole pressure cells. A brief description of the fabrication, installation, and pressurizing equipment is given and pressurizing procedures are discussed. Theories available on evaluation of data from the flat and cylindrical pressure cells and examples of data analysis and stress evaluation are also presented.

Jan 1, 1991

This Bureau of Mines report summarizes the research, development, and evaluation demonstrations conducted by the Bureau of Mines under the Health and Safety Act of 1969 to improve the means of notifying miners underground, who are away from their own phone, that they are being called.

Jan 1, 1977

By J. L. Reuss

The Bureau of Mines derived information on the softening characteristics of both unfired and indurated iron ore pellets as measured by hot compression strength in a laboratory study. A surprisingly high hot strength (240 1b per ½ -inch spheroid) was developed by unfired magnetite pellets near 900° C; lesser maxima were developed by pellets made from hematite and specularite concentrates near 1,000° C. Those from goethite remained weak throughout the pre induration heating. Fully indurated commercial pellets retain a high resistance to softening when heated in air. On the contrary, in a hot reduing atmosphere their high cold crushing strength dissipates rapidly. At 1,000° C, for example, the average compression strength of seven different commercial pellets was 110 lb; at 1,100° C, the hot strength was only 60 lb. After a rather sharp initial drop, the loss of strength with increase of temperature was gradual. There was no sudden collapse, nor any significant difference, in behavior of commercial pellets whether made from magnetite or hematite concentrates.

Jan 1, 1968

By Van H. Manning

The term war minerals has been applied t.o those ores and minerals that were largely imported. before the war. Among the mon important of these are manganese, essential for making high-grade steel for munitions and industrial use; graphite, for u,.akin1 crucibles; tin, for plating utAmsils and for bearing-met.al; mereury, used as fulminate t.o explode shells; pot.uh, for making fertilizer and explosives; tungsten and molybdenum, for high-speed t.ool steel; antimony, for hardening bul!et lead; chromite, for tool steel, for tan- , ning leather, and as a refractory lining in furnaces; magnesite, for :refract:A>ry linings; mica, as insulating material; platinum, for the manufacture of sulphuric acid and for electrical apparatus. When the United States entered the war it was clear that every ship would be needed and that the number available for importing minerals would be small. Hence a quick and thorough survey of domestic resources was necessary. . Throughout the war the scope and volume of the war-minerals work increased until it covered practically every mineral that was known t.o be or was liable to be in short supply.

Jan 1, 1919

By Paul V. Mullins

Review and evaluation of all available data on the vapor pressure of car-bon dioxide at the ice point, including previously unpublished results obtained by the Bureau of Mines, are presented. Suggested corrections and adjustments to all the data yield an average value of 26,136.4 mm mercury. Indicated agreement is within plus 1 part in 8,000 to minus 1 part in 11,000. A novel pressure bomb in which a sample of pure carbon dioxide is placed and sealed by a diaphragm fluid separator and its use as a reference pressure standard for extended and repeated use in the calibration of deadweight gages is described.

Jan 1, 1966

By W. R. Crane

Recent papers on support of roof and top rock in mines representing present practice in so far as it hits been described by engineers in all of the principal mining countries, cover a relatively aide range of topics. The papers abstracted herein include such subjects as the testing of materials of support, failure and movement of rock above workings, effect of excessive pressures on rock masses, axed the application in mines of timber, metal, concrete, packing, and filling support. It is not within the scope of this paper to present a logical and orderly discussion of the elements of support and their application to conditions influenced by the material worked or the method of mining. Only the essential facts of a paper appear in the abstracts, the idea being to give a fairly clear picture of the behavior of various types of support under brows conditions and to put into concise form important information concerning present practice, modifications of practice, and the trend toward new practice. With such valuable facts from others experience made readily available, it Is hoped that the engineer with particular and often trying problems may obtain suggestions that will be immediately helpful.

Jan 1, 1932

By C. M. K. Boldt

The Bureau of Mines surveyed waste disposal sites at 18 metal and non-metal mines and conducted laboratory and full-scale field tests to de-termine the effects of tailings deposition techniques on physical properties of tailings pond beaches. Survey data included measurements of beach slopes, descriptions of deposition techniques, and measurements of beach physical properties taken at various distances from the point of discharge. Laboratory tests involved depositing two types of tailings, each with different grain-size distributions, into a settling trough and determining the resultant physical properties of settled materials along the length of the beach. Side confinement and the closeness of the water pool to the point of deposition caused the laboratory results to be inconclusive. Full-scale field deposition tests conducted at the tailings pond of a cooperating mine showed that there were similarities in relationships between exit velocities of tailings slurry and physical properties of the settled tailings on the beach.

Jan 1, 1988

By H. H. Heady

A naphtha obtained by destructive, recycle hydrogenation of crude shale oil, produced by gas-combustion retorting of Colorado oil shale, was found by the Bureau of Mines to contain 49.1 percent paraffins, 20.3 percent cycloparaffins, 7.8 percent olefins, and 22.8 percent aromatics. The naphtha contained only minor amounts of sulfur, nitrogen, and oxygen compounds. Compounds containing less than 5 carbon-atoms per molecule were removed by distillation before analysis. The paraffins where predominantly straight-chain compounds; n-Hexane was present in the largest quantity, and the other straight-chain paraffins decreased in amount as the molecular weight increased. The cycloparaffins, which contained both cyclopentanes and cyclohexanes, were evenly distributed throughout the boiling range. Although the naphtha had been produced by hydrogenation, it contained a small quantity of olefins. Straight-chain olefins with a terminal double bond comprised about two-thirds of these compounds. Among olefins with an internal double bond, those having trans configuration were present in three times the quantity of those in the cis form. In the aromatics all but one of the alkylbenzenes having nine or less carbon-atoms per molecule were identified; toluene was present in the greatest quantity. Only a few of the higher molecular-weight homologs were identified. The composition of the naphtha was computed from analyses of 105 narrow¬boiling distillation fractions. Volume, density, refractive indices, bromine number, and an ultraviolet spectrum were determined on each fraction. From these data the hydrocarbon-group composition of each fraction was estimated. A silica gel adsorption analysis was used to check the values of nearly one-third of the fraction calculated from physical-property data. Mass and infrared spectra were obtained on some fractions for identifying individual compounds or types of compounds, such as terminal olefins.

Jan 1, 1960