Search Documents

By Sean Gallagher

The vast majority of ergonomics research has addressed the demands of work in standing or sitting postures, and understandably so. However, many workers (for example, underground miners, aircraft baggage handlers, plumbers, agricultural workers, mechanics, and others) are often required to adopt postures such as kneeling, stooping, squatting, or lying down for significant periods of the work day.

Jan 1, 2005

By Fred N. Kissell

In This Chapter [Measuring the gas emission from the coal Methane at the top of the silo Methane at the load-out area and Actions taken after a silo explosion] Methane accumulations in coal silos have resulted in the occasional silo explosion. These can be quite violent and dangerous because coal dust adds to the strength of the blast. However, with the appropriate precautionary measures, methane accumulations in silos can be greatly reduced. Mine Safety and Health Administration (MSHA) regulations at 30 CFR2 77.201 require that the methane content in the air of any coal silo be maintained below 1.0 vol %.3 Also, MSHA requires that methane tests be conducted before any electrical equipment is energized, unless a continuous monitor capable of deenergizing the electrical equipment is used.4 Measuring the gas emission from the coal. The first necessary step in dealing with silo methane issues is to measure the gas emission from the coal going into the silo. Such measure-ments allow one to estimate the silo ventilation needs and permit a comparison with the methane controls used at other mines that have similar gas levels. The gassiness of the coal can be measured by taking conveyor belt grab samples.5 Matta et al. [1978] measured the gas emission from conveyor belt grab samples using a simple desorption test. To conduct the test, they collected several grab samples of coal, weighing a few pounds each, from the conveyor belt entering the silo.6 They then sealed the coal into an airtight sample container that was equipped with a valve and short hose along with a pressure gauge. Every few hours they opened the valve and bled the emitted gas into a water-filled graduated cylinder that had been inverted and placed in a pan of water (Figure 11–1). The results are shown in Figure 11–2.

Jan 6, 2006

By Launa G. Mallett, Jr. Brnich

Overview: The first step to emergency preparedness and maintaining a safe workplace is defining and analyzing hazards. Although all hazards should be addressed, resource limitations usually do not allow this to happen at one time. Risk assessment can be used to establish priorities so that the most dangerous situations are addressed first and those least likely to occur and least likely to cause major problems can be considered later. Purpose: This training package was developed to assist instructors as they (1) determine how to use risk assessment to improve safety preparedness and (2) present risk assessment concepts and tools to trainees. The concepts and tools presented here can be applied to any mine hazard.

Jul 1, 2003

By R. Blickensderfer

An impact wear testing machine was devised by the Bureau of Mines that simulates the repeated impact conditions encountered in large milling and grinding operations where breakage and spalling are problems. The apparatus provides data on materials that may help in the design of alloys with improved resistance to deformation, spalling, and breakage. The test blocks are 2 in thick by 6 in by 8 in. Impacts are produced by dropping 3-in-diam balls weighing 4 lb from a height of 10 ft. Tests were run until breakage occurred or to a total of 100,000 impacts. Four types of failures of the test block were observed: (1) cold flow of the bulk material by plastic deformation, (2) flaking of the surface in the impact region, (3) spalling of the block to form a crater in the region of impact, and (4) breakage of the test block into two or more major pieces. The effects of composition, heat treatment, microstructure, and hardness on types of failure are discussed.

Jan 1, 1983

The coal-bearing strata of Oklahoma occur in the eastern part of the state over an area of 14,500 square miles, 20.7 percent of the state's total area. Commercially valuable deposits of bituminous coal cover about 8,000 square miles in seams ranging from ten inches to five feet thick. Estimated reserves in Oklahoma are 1.6 billion tons, representing 0.3 percent of U.S. coal reserves. The vast majority of coal mined in Oklahoma used in a single power plant within the state. Oklahoma gained primacy when its regulatory program was conditionally approved January 19, 1981. Authority for the state to administer the Abandoned Mine Land program was granted January21,1982. On April 30,1984, the Office of Surface Mining substituted direct federal enforcement of the inspection and enforcement portions of the Oklahoma program. This substituted enforcement was based upon a finding by OSM that Oklahoma had not operated the inspection and enforcement portions of its program effectively. As of January 1, 1986, Oklahoma inspection and enforcement authority was reinstated. Full program authority was granted to Oklahoma on January 14, 1986.

Jan 1, 1992

By Don M. Coulter

"INTRODUCTION Bauxite, in Appalachian Alabama, occurs in the Rock Run and Goshen Valley districts in Cherokee County; in Nences Creek Valley near Jacksonville; near Anniston in Calhoun County; north of Fort Payne in DeKalb County; near Ashville in St. Clair County; and near Talladega in Talladega County.In February 1942, Preston E. Cloud, Jr., assistant geologist, Federal Geological Survey, began a study of these bauxite deposits and the geology relating thereto.The Bureau of Mines established field headquarters at Piedmont, Calhoun County, in July 1942. Mineral agreements covering a total of 11,097 acres were executed with 15 landowners in the Rock Run district; 38 in the Goshen Valley district, covering 7,575.5 acres; and 3 in the Nances Creek Valley district, covering 988.5 acres. Drilling was done on the properties of 9 land¬owners in the Rock Run district, and on the property of 1 landowner each in the Goshen Valley and the Nances Creek districts. Drilling began October 26, 1942, and ceased on May 17, 1943.Power drilling was supplemented by a labor crew that drilled hand-auger holes in shallow deposits and sampled .old shafts, mines, and mine dumps.In all, 222 holes for a total of 13,250 feet were drilled. Of these holes, 88 penetrated bauxite but too low in grade to constitute ore."

Mar 1, 1948

By Sean Gallagher

Background. There is currently little information regarding factors associated with specific modes of motion segment failure using a fatigue failure model. Methods. Thirty-six human lumbar motion segments were fatigue tested using spinal compressive and shear loads that simulated lifting a 9 kg weight in three torso flexion angles (0°, 22.5°, and 45°). Twenty-five segments failed via fatigue prior to the 10,000 cycle maximum. These specimens were visually inspected and dissected so that the mode(s) of failure could be determined. Failure modes included endplate fractures (classified into nine varieties), vertebral body fractures, and/or zygapophysial joint disruption. Logistic regression analyses were performed to determine whether certain morphometric variables, amount of motion segment flexion, disk degeneration scores, and/or loading characteristics were associated with the occurrence of specific failure modes. Findings. Results indicated that stellate endplate fractures were associated with increased posterior shear forces (P < 0.05) and less degenerated discs (P < 0.01). Fractures running laterally across the endplate were associated with motion segments having larger volumes (P < 0.01). Endplate depression was more common in smaller specimens (P < 0.01), as well as those experiencing increased posterior shear force (P < 0.05). Zygapophysial joint damage was more likely to occur in a neutral posture (P < 0.01). Interpretation. These results suggest that prediction of failure modes (e.g., specific endplate fracture patterns) may be possible (at least for older specimens) given knowledge of the spinal loads along with certain characteristics of the lumbar spine. Published by Elsevier Ltd. Keywords: Lumbar spine; Endplate fractures; Zygapophysial joints; Morphometry; Disk degeneration; Motion segments; Aging

Jan 1, 2006

By C. L. Karr

U.S. Bureau of Mines (USBM) research has shown that fuzzy logic and genetic algorithms (GA&apos;s) have great potential for industrial process control. A technique has been developed by the USBM in which GA&apos;s are used to substantially reduce the time needed to design fuzzy logic controllers (FLC&apos;s).This technique shows promise as an efficient, robust approach to developing control systems. The research described in this report is twofold. First, the basic approach to developing an FLC using GA&apos;s is presented. The GA-designed FLC is developed for a specific physical system, a pH titration system. Second, empirical results are presented in which variations in the FLC implementation are compared. Specifically, the effects of altering five aspects of the pH FLC are considered: (1) membership function form, (2) number of fuzzy classes, (3) the center-of-area method, (4) implication operator, and (5) fuzzy rule form. Results indicate that (1) the technique in which GA&apos;s are used to design FLC&apos;s is effective, and (2) when this technique is used, variations in FLC implementation have little effect on FLC performance in a chosen control problem.

Jan 1, 2010

By Nancy Estrada, Jane Nowell, Cathy Jennings, Debra Yniguez, Carol Lavery, Kristin Harrer

Pilots of the MH-60S helicopter are exposed to continuous whole body vibration (WBV). Pilot fatigue is a growing operational concern due to the increased frequency of extended durations of missions (6-8+hours) in support of Operations Iraqi Freedom and Enduring Freedom. Endurance aspects of the currently used rotary wing seating systems were not optimized for the longer missions and wide range of pilot anthropometric measurements, which is now typical of naval aviation. The current seating systems were designed primarily to meet crashworthiness requirements, not for the wide range of pilot anthropometry or to mitigate WBV. Albeit, an issue, pilot fatigue and reduced mission effectiveness are also critical concerns. Current Hazard Reports indicated that pain in pilots’ legs and backs begin two to four hours into the flight and increase with time. Mission readiness also decreases with an increase in flight duration due to the constant distraction of pilots shifting in their seats while trying to get comfortable. Froom, et al [2] reported a dose-response relationship between the length of military helicopter flights and back discomfort. He also concluded that this pain is typically dull, over the lower back, and its prevalence and intensity are dependent on the total flight hours of exposure. Methods This study evaluated WBV produced in the pilot seating systems onboard the MH-60S. The purpose of the study was to test and compare the effectiveness of two different seat cushions, the current seat cushion versus an anti-vibration seat cushion. Both seat cushions were measured for acceleration levels averaged over five-minute intervals using a triaxial seat pad accelerometer. The recordings were completed for a 3-hour straight and level flight. A frequency analysis from 0-80 hertz (Hz) was conducted on all acceleration measurements to determine the dominant axis and frequency of the pilots’ vibration exposure. The results were then compared to the applicable Threshold Limit Values (TLVs) established by the American Conference of Governmental Industrial Hygienists (ACGIH) [1] and the International Organization for Standardization (ISO) 2631.1 [3] to determine the MH-60S pilots’ permissible exposure time for both seat cushions. Results The results of the study showed that for both seat cushions the vibration levels of the z-axis at 16 Hz had the shortest allowable exposure duration, according to the ACGIH TLVs. In the z-axis at 16 Hz, the MH-60S’s current seat cushion’s acceleration levels indicated an exposure time limit of approximately 6 hours, while the anti-vibration seat cushion’s acceleration levels pierced the 8-hour exposure time limit curve. This is shown in the graph below.

Jan 6, 2006

By Claud Johnson, G. Roger Miller, Kristine M. Krajnak, Stacey Waugh, Oliver Wirth

Workers exposed to vibrating hand tools are at risk of developing symptoms such as cold-induced vasospasms, loss of tactile sensitivity, and loss of grip strength in the fingers and hands. These symptoms are known collectively as vibration white finger (VWF) or hand-arm vibration syndrome (HAVS). Symptoms of VWF or HAVS are in part due to repeated and prolonged peripheral vasoconstriction[1, 2]. The reduction in blood flow that occurs with vasoconstriction can result in oxygen deprivation (hypoxia) in soft tissues, such as nerves and muscle, and lead to functional and structural changes in these tissues. The present study examined muscle tissue to determine if vibration-induced changes in transcript levels and protein concentrations result in enhanced vasoconstriction and hypoxia. Manual dexterity was also assessed intermittently to determine if vibration-induced changes in cellular factors are accompanied by performance deficits. Methods An animal model was developed to study the biological and functional changes that occur in response to repeated segmental vibration exposures. In this model, the right paw of intact rats was exposed to a platform vibrated at a frequency 250 Hz and amplitude of 49 m/s2 to simulate the vibration characteristics of hand-held grinders. Three groups of 8 rats each were studied: a vibration-exposed group, an exposure-control group, and a cage-control group. Exposure sessions, with or without vibration, were conducted 4 hr/day, 5 days/week for 5 weeks. Manual dexterity was assessed intermittently during the 5-week exposure period with the Montoya stair-case test[3], which quantifies the rat’s ability to reach for, grasp, and retrieve small food pellets placed below the rat on different levels or steps. Following the 5-week exposure period, the flexor muscles of the right forelimb were collected for analysis of gene expression, protein concentrations, and immunohistochemistry. Results Vibration-exposure resulted in an approximate 2-fold increase in the expression of a2C and a1D receptor transcripts in flexor muscles (Figure 1). These receptors mediate norepinephrine-induced vasoconstriction in smaller arteries. Vibration-exposure also resulted in an approximate 2-fold increase in hypoxia-induced factor-1a (HIF-1a), a transcription factor that is expressed in response to tissue hypoxia. Western analyses demonstrated that restraint caused a decrease in a1-receptor protein concentrations in the flexor, but vibration-exposure prevented the restraint-induced reduction (Figure 2). Immunohistochemistry performed on flexor muscles (not shown) demonstrated that a1 receptors are primarily located in arteries; maintained levels of these receptors could contribute to prolonged vasoconstriction following repeated vibration exposure. The staircase test showed some performance improvement, or a training effect, in manual dexterity for the control groups but not the vibration-exposed group (Figure 3).

Jan 6, 2006

By Avery H. Reed

ALABAMA&apos;S mineral industry continued to expand. This was a record year for many commodities, with expansion in almost all industries. New records were established for the production of native asphalt, fixe clay, miscellaneous clay, kaolin, bentonite, lime, scrap mica, salt, sand and gravel, crushed limestone, crushed marble, and tale. Among the States, Alabama ranked second in the production of bauxite, third in the production of scrap mica and native asphalt, and fifth in iron ore. The mineral industry of Alabama was dominated by the mining and processing of coal and stone, the manufacture of cement, and the production of crude petroleum, which together comprised 87 percent of the total value of production, compared with 86 percent in 1963. The iron ore industry continued to decline. This was the first year in which consumption of imported iron ore exceeded the consumption of domestic iron ore. The coal industry recovered from the slump caused by the abandonment of red iron ore mining by United States Steel Corp., and production expanded 17 percent, for the best year in coal mining since 1948. During the year, the one-billionth ton of coal was mined within the State.

Jan 1, 1965

By L. A. Stewart

This is one of a series of reports prepared by the Federal Bureau of Mines on mining methods, performance, and costs at individual mines in the United States. The primary purpose of these papers is to promote development and conservation of our mineral resources by disseminating technological information on methods, practices, and results that may be applied to the engineering analysis and solution of mining problems. This report discusses the highly selective mining methods of the Jaquays Mining Corp. at the Regal asbestos mine, 45 road miles northeast of Globe, Ariz. The milling method at the Globe plant is discussed briefly, and the extraction ratios of the various grades of fiber are tabulated. The proposed flowsheet of a new mill under construction is shown.

Jan 1, 1961

By J. W. Thompson

Be if enacted by the Senate and House of Representatives of the United States of America in Congress assembled, That deposits of coal, phosphate, sodium, oil, oil shale, or gas, and lands containing such deposits owned by the United States, including those in national forests, but excluding lands acquired under the Act known as the Appalachian Forest Act, approved March 1, 1911 (Thirty-sixth Statutes, page 9G1), and those in national parks, and in lands Withdrawn or reserved for military or naval uses or purposes, except as heroinafter provided, shall be subject to disposition in the form and manner provided by this Act to citizens of the United States, or to any association of such persons, or to any corporation organized under the laws of the United States, or of ;iny State or Territory thereof, and in the case of coal, oil, oil shale, or gas, to municipalities: Provided, That the United States reserves the right to extract helium from all gas produced from lands permitted, leased, or other- wise granted under the provisions of this Act, under such rules and regulations as shall be prescribed by the Secretary of the Interior: Provided further, That in the extraction of helium from gas produced from such lands, it shall be so extracted as to cause no substantial delay in the delivery of gas produced from the well to the purchaser thereof: And provided further, That citizens of another country, the laws, customs, or regulations of which, deny similar or like privileges to citizens or corporations of this country, shall not by stock ownership, stock holding, or stock control, own any interest in any lease acquired under the provisions of this Act.

Jan 1, 1921

By Albert L. Toenges

This report is the second of a series describing methods and systems of mechanical mining; where operations are conducted on more than one shift. The first report, Information Circular 7014,4/ describes mining operations at 14 mines and the present paper describes operations at 11 additional mines. The purpose of this study is to analyze the advantages and disadvantages of the various types of equipment and mining systems now used where more than one shift is worked per day. Physical conditions vary in different and in the same mining districts and determine, together with economical considerations, the systems of mining and the types of mechanical loading equipment to be used. The information presented in this paper may be helpful to operators or others who may contemplate installing a mechanical mining system. The equipment used in the mines described comprises conveyors, scrapers, mobile loaders, mobile conveyors, and combination of these types. The description of the mining systems and practices at the mines investigated is detailed only as they relate to and affect mechanization. In computing the operating data in mines that are not totally mechanized, employees not working directly on production have been charged to output from mechanized sections in proportion to the percentage of mechanization. The operating data for comparing various systems are for an average working dry, as the number of men working on idle days varies greatly in different mines.

Jan 1, 1939

By Hisataka Sakakibara

Although the pathophysiology of vibration-induced white finger (VWF) is still under discussion, evidence has been accumulated to understand the underlying mechanism. VWF is pathophysiologically characterized by an enhanced vasospastic response to cold, which can result from an imbalance between vasoconstriction and vasodilation in the digital arteries in response to cold (i.e., vasoconstriction-dominant). The imbalance is supposed to be due to faults in vascular vessels and sympathetically mediated vascular tone. Enhanced vasospastic response to cold Narrowing of arterial lumen with medial smooth muscle hypertrophy. Possible functional factors for enhanced vasoconstriction • Increased sympathetic nervous activity to cold (e.g., norepinephrine) • Increased release of endothelin-1 (ET-1; an endothelial-dependent vasoconstrictor) from the endothelium • Increased reactivity of alpha2-adrenoreceptors to cold Possible functional factors for decreased vasodilation • Decreased release of nitric oxide (NO; an endothelial-dependent vasodilator) from the endothelium • Decreased release of calcitonin gene-related peptide (CGRP; a vasodilatory neuropeptide) from sensory afferents The question is how their interrelations or imbalances among them are Vibration and arterial damage The next question is, how does hand-arm vibration exposure induce such pathophysiological changes in VWF patients? Recent morphological evidence from animal experiments shows that vibration acceleration stress (including shear stress) and smooth muscle contraction contribute to arterial damage of smooth muscle and endothelial cells. The vibration-induced arterial damage is frequency-amplitude-dependent.

Jan 6, 2006

By Laurence G. Trudell

A geologic framework for interpreting stratigraphic and geographic variations of the Green River Formation in the Piceance Creek Basin is developed from lithologic data accumulated by the Bureau of Mines from oil-shale coreholes. From detailed Bureau of Mines descriptions of samples from nine coreholes and supplementary lithologic data from seven additional sampled sections, three cross sections were constructed along lines transecting the basin. Plotted as lithologic columns with corresponding oil yields and resistivity logs, the sampled sections are correlated on a time-stratigraphic basis. Distribution and correlation of nahcolite and halite zones are shown, and the approximate base of leaching of these saline minerals is indicated. General lithologic characteristics of members and zones are discussed and interpreted. Large-scale lithologic logs illustrate the nine Bureau of Mines core descriptions, and the complete description of Bureau of Mines-Atomic Energy Commission Colorado Corehole No. 1 is included in an appendix. The time-correlated cross sections provide a necessary framework for understanding the depositional history of the Green River Formation and will facilitate evaluation of oil shale and other mineral resources in the Piceance Creek Basin.

Jan 1, 1970

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East, providing more than 80 % of the region&apos;s foreign exchange. In 1992, the 15 countries that constituted the region accounted for 29.5 % of world crude petroleum output, 20 % of world natural gas plant liquid production, and 5 % of world dry natural gas production. Only Cyprus and Lebanon were not crude petroleum producers. A fairly wide range of non fuel minerals is also produced in the region. The most significant are boron minerals, bromine, chromite, gypsum, phosphate rock, potash, strontium, and sulfur. However, the variety of minerals produced, output levels, and the size of the overall non fuel mineral economy of the region is dominated by Iran and Turkey. Turkey, with a diverse mineral production and strategically situated between Europe and the Middle East, was first in world production of run-of-mine boron minerals, second in strontium behind Mexico, and fourth in pumice. It was also a significant world producer of chromite, magnesi&apos;lm compounds, mercury, and sodium sulfate. Turkey was also the Middle East&apos;s largest cement and steel producer. Iran continued to expand output of most mineral commodities following the war with Iraq from 1980 to 1988. It was a significant world producer of gypsum and strontium and on its way to becoming a major iron and steel producer in the region. Despite a very small domestic mineral industry, Israel was second in world production of bromine and a significant producer of phosphate rock and potash. In terms of processed minerals, Israel was a major world diamond cutting center and exporter of cut diamond. Jordan ranked sixth in world production of phosphate rock. Saudi Arabia was eighth in world production of sulfur.

Jan 1, 1994

By W. E. Lamont, R. E. Perry, I. L. Feld

The Bureau of Mines conducted research to determine the conditions required to sinter a pyrrhotite calcine into a product suitable for iron blast furnace feed . The calcine , a fine - grained iron oxide produced by roasting sulfide flotation concentrate , analyzed about 60 percent iron and 1 percent sulfur . Sintering of the calcine without prior pelletization was not successful whereas firing of preformed calcine charges yielded acceptable sinter products . Batch tests were made to study the effect of the following variables on the sinter quality : Size of green pellets in the charge , quantity and type of internal carbonaceous fuel used , depth of sinter bed , moisture content of the charge , flux additions , and binder additions . The batch and continuous sinter tests showed that minus 1 / 4 - inch pellets prepared from a mixture of the calcine , coke , dolomite , and water gave sinter cakes analyzing 57 to 61 percent iron and 0.05 to 0.02 percent sulfur .

Dec 1, 1963

By Chi-Mun Song, Seok-Hyun Choi, Seok-In Hong, Han-Kee Jang

Accurate measurement and evaluation of hand-transmitted vibration from a power tool is an important issue for tool manufacturers, because they are obliged to develop low-hazard power tools for workers. The International Standard ISO 5349(1) dictates a systematic procedure for the measurement and evaluation of hand-transmitted vibration. However, the uncertainty in this measurement is too large for manufacturers to apply such data to the design and modification of power tools. There can be several sources of this uncertainty in such measurements; e.g., operator-dependent, power tool-dependent, and operational conditions (see Table 1). For a manufacturer to characterize the exposure of a power tool’s use to a given level of vibration, the relationship between these uncertainty factors and the measured vibration must be elucidated. In this study, we investigated the effect of several factors on the uncertainty in measurements. [ ] Methods In this study, some of the factors in Table 1 were selected for examination, and their effect on the measured variation was quantitatively investigated. Three tools from the same manufacturer were sampled at random in our experiments, and each of five of the same type of insert (disks or tips) was installed into each tool. Although each of the tools and inserts were of the same design and were made by the same production process, they differed from one to another, which can be a source of the variation in the measured vibration. Three human subjects participated in our experiments, which were carried out as stated in ISO 5349. The subjects were asked to maintain their posture, and the applied force was kept as constant as possible. The applied force was monitored using an indirect method, where vibration energy was displayed in real time during the experiment using a three-axis accelerometer attached to the work piece at a specified point. The appropriate range of the applied force was predetermined to cover the range of real work operations. The engineering tolerance between the inner diameter of a grit disk and the outer diameter of the tool shaft leads to an eccentricity of the mass at the center of the disk. The degree of eccentricity varies with installation, and this is another source of uncertainty. In our study, the effect of this eccentricity was investigated by carrying out repeated assembly and disassembly of an insert.

Jan 6, 2006

By Mark L. Chatman

This report presents an economic mineral assessment and Inventory of mines and prospects In the approximately 176,000-acre Patagonia Mountains-Canelo Hills Unit of Coronado National Forest. Deposits or areas most likely to experience future development are characterized in terms of their economics, based on data acquired by the author from a variety of sources, and supplemented by USBM field data collected by other workers in 1990 and 1991. Numerous mine maps, rock-chip sample assays, and detailed descriptions of mine and prospect sites are in this report and appendixes. Heavy but sporadic mining, mainly between the 1850&apos;s and 1950&apos;s was nearly all confined to the Patagonia Mountains. High-grade sulfide veins, replacements, and skarn deposits accounted for most of the production, which included large quantities of zinc, lead, copper, and silver, and considerable quantities of gold. Small Quantities of molybdenum, manganese, tungsten, and placer gold have been mined. Most of the traditionally mined metalliferous sites will not see future activity due to the low tonnages present and removal of most high-grade rock. Possible future development areas include copper porphyries and breccia pipes; most are too deeply buried for current development. Localities where similar deposits may be concealed are identified.

Jan 1, 1994