Search Documents

By Des Bolton

With the introduction of Cast Blasting techniques, field controls of Drilling & Blasting operations became more important. New drills were purchased which were equipped with sophisticated instrumentation and more accurate drilling plans were required. Concurrently a decision had to be made on the replacement of borehole logging equipment owned by the mine. The use of a contractor to log blast boreholes was eventually decided upon, the information gained from this operation is used in the short-term drill and blast planning and may also be used to assist in the coaling operation if density I quality correlations prove acceptable.

Jan 1, 1994

By C. Pelley, S. Kelebek, S. Gregersen, P. Katsabanis

A series of small scale tests have been conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the physical properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Young’s modulus, Poisson’s ratio, P-wave, S-wave velocity, point load strength index and grinding work index were evaluated for samples without any blasting load and for samples which had received a variety of blast loads, such as a simple side impact from a detonating cord, or combined impacts without any delays and with very short delays. The investigation covered two types of rock, granodiorite and limestone. The effect of blasting load on the physical and rock mechanics parameters of the rock was clearly shown and damage was quantified and related to loading. However the work index did not show significant differences between blasted and not blasted samples, probably due to the relatively low level of impact. Numerical modelling using the AutodynTM code was used to demonstrate damage development in the various configurations tested.

Jan 1, 2003

By Tom Treleaven

Several nonelectric blast initiation systems have been developed since the mid 1970's. Until that time, most blasts were initiated either electrically with electric blasting caps or nonelectrically with detonating cord. What the development of these new systems was attempting to accomplish was to provide a system that was nondisruptive to the stemming or explosive column, but still possessed the safety and flexibility inherent in nonelectric systems.

Jan 1, 1991

By G. R. Adhikari

Step 4: Selection of explosives and initiation system Various types of explosives are manufactured in India and a wide choice is available among them that include nitroglycerin based explosives, slurries, emulsions, ANFO (ammonium nitrate mixed with fuel oil) and heavy ANFO. The choice is also available between cartridged and bulk loading systems. In Indian mines, much importance is unduly given to the cost of explosives alone which is not conducive to optimization of blast design parameters. The concept of energy per meter of blasthole and the way in which the total explosive energy is partitioned between shock and heave is not considered in the prevailing practices. Besides, very little efforts are made to objectively evaluate the performance of explosives for a given site condition. Tailoring explosives is limited to changing the density of the bulk explosives. Cartridged explosives are still being extensively used in large operations where bulk explosives should be the preferred choice.

Jan 1, 2002

By Qi Shifu, Guo Tao, Liu Haoquan, Yao Chaogui, Zheng Li

Abstract: To excavate oil-gas pipeline ditches in a rocky region or area the explosive method is needed. When a parallel ditch is to be dug by blasting near or in the vicinity of an existing pipeline, a safe criterion must be determined to ensure safety for the latter. In this investigation, with the construction of the second phase of the West-East Gas Pipeline Project, we carried out real blasting tests and numerical simulations to explore the safety criteria for the existing pipeline. Through this investigation, we obtained the safe strain elasticity threshold es2000µe, blast vibration velocity calculation formula, and the maximum vibration velocity Vmax=14cm/s(5.51in./s) for the pipe under blast shock loading, and worked out how to determine the charge size in the follow-up blasting excavation. These results can be used to determine the maximum explosive weight per delay and decide delays for the initiation circuit network in blasting a parallel pipeline ditch, and to make safety assessments for the existing pipeline in service. Having successfully been applied in the second and third phases of the West-East Gas Pipeline Project, China-Russia Oil Pipeline Project and China-Myanmar Gas Pipeline Project, these findings are very significant for other similar pipeline construction.

Jan 1, 2014

By ATF Publications

The following is a summary of the changes that were incorporated into the new Federal Explosives Regulations, 27 CFR Part 55, dated 9/2000. However, in light of the recent events of September 2001, additional changes in the Federal Explosives Laws and Regulations may be forthcoming. The nature and extent of any such potential changes are impossible to gauge at this time. However, this synopsis of the changes contained in the September 2000 Orange Book, ATF P 5400.7 was current at the time of this writing. Any questions regarding this paper should be directed to the Public Safety Branch in ATF Headquarters in Washington, D.C.

Jan 1, 2002

By Brian Gar Wingfield

Bulk explosive systems have developed from the infancy stages in the early sixties to a sophisticated process of the nineties. With ever changing bulk explosives technology, bulk delivery and loading systems needed to keep pace. Efficiency, as compared with packaged loading, was the keyword allowing faster loading of trucks and shots. Efficiency was also improved by the explosives coupling factor that bulk loading permitted.

Jan 1, 1991

By Wes Bender

Considering the current interest in Global Positioning System (GPS) usage, it might be timely to look at a more efficient means of utilizing these instruments. The GPS system currently utilizes 28 satellites (4 are spares) circling the earth in an inclined orbit. Normally at least six satellites are within your area of reception at any given time. The satellites broadcast an extremely accurate time signal and an almanac containing all the satellites’ orbital data. This information is updated regularly as the satellites circle the earth. Your GPS receiver, once it has picked up one satellite’s broadcast, can then determine which other satellites should be available for plotting.

Jan 1, 2002

By R. F. Favreau, P. Favreau

Rock excavation is the first process in the cycle of operation of a mine, and efficient blasting is paramount to the profitability of the mine. The traditional way to design blasts has been by trial and error, based on the experience of the designer. This is probably the only important engineering practice which continues to be done without a precise engineering technique. The efficiency of most other mine processes has been improved by the use of high-tech, while a majority of blast design has not yet profited from the advantages of the computer. However, with the advent of the high-tech blast simulator Blaspa, it has become possible to design the parameters of the blast according to normal engineering practices. Over the last 50 years, the chemical and physical mechanisms which occur during a blast have come to be identified; they are reviewed in section B. Although these mechanisms are complex, they have nevertheless been expressed in terms of mathematical equations which have been assembled together in the computer to create the blast model Blaspa.

Jan 1, 2002

By J Lyall Workman, Peter N. Calder

"Large hole rotary drilling is one of the most common methods of producing blastholes in open pitmining. Large hole drilling generally refers to diameters from 9 to 17 inch (229 to 432 mm), however aconsiderable amount of rotary drilling is done in diameters from. 6% to 9 inch (165 to 229 mm). Thesesmaller diameters are especially prevalent in gold mining and quarrying."

Jan 1, 1996

By Thierry Bernard, Phillipe Cappello, Jean Marc Laboz

"The main reasons of the emergence of electronic detonators are linked to:-Local urban development close to mining operation sites-Environment regulations"

Jan 1, 1995

By Paul Downing

When was the last time the documents and paperwork were cleaned out of the glove boxes, door pockets, under the seats and above the visors in your company vehicles? Insurance cards that expired three years ago and vehicle registrations from 1999 through 2003, for instance, don’t do any good and just take up space

Jan 1, 2008

By Claude Cunningham

Ths oonoept of precise. eooursts timing with Elsotronic Delay Detonators (EDD’s) was first ssriously sddresssd in ths mid 80’s end much wss made of the cheapness end profusion of digital wstohes in terms of the likelihood of EDD’s also being cheap and essyto produce. Ten years Iater. with every major explosives group end many elsotronios groups having instituted projects to capitalize on the promise of these devices, production devices are still to come into asneral use.

Jan 1, 1994

By Kai Nielsen

The paper presents the results of several industrial and laboratory blasting, crushing and grinding tests and experiments investigating how blasting can influence the subsequent crushing and grinding operations. The paper also describes how these results can be used in order to optimize the entire comminution process from solid ore to a semifinished or marketable product. Two cases are presented, one looking at the processing of fine grained taconite ore, and the other discussing the processing of raw milling product for cement burning.

Jan 1, 1998

By Eric Kelley

Having been retained as a legal expert for the fatality at the Canberra, Australia project, it made me aware of how good intended blasters profess to be implosion experts. Owners and contractors can be misled by these representations, seeing a video of Directionalized Structures constructed of reinforced concrete may be impressive to watch, but lack sound evidence of the true mechanics of an actual “implosion”; on steel structures more prevalently. If any well intended blaster comes to a determination that he can implode a structure, it should be not be construed he cannot. It should be well investigated that the specific blaster has verifiable experience. What happened in Australia reflects on all end users of explosives. I have heard a direct quote in our project in Alberta, “We don’t want to have what happened in Canberra”. Such a tragedy could have, and should have been avoided. Simple by using the “Right Tool for the Job”. We should sideline egos and economics. Would any competent blaster compromise his or her reputation, company or insurability? More importantly, have an honest conscience knowing that if the proper explosive is available, use it, don’t shortcut it. If possible expand the schedule. Better, yet, examine all avenues before the project, and last, cancel the project. A human life is our best asset and should not be compromised.

Jan 1, 1999

By Guillermo Silva, P. Katsabanis

The conventional approach to design wall control blasts relies on the borehole pressure as the most important explosive parameter. Borehole pressure is intimately linked to explosion pressure, which in turn is related to the detonation pressure of the explosive. For fully coupled charges, the borehole pressure is equated to the explosion pressure, while for decoupled and decked charges its value is typically calculated under the assumption that the explosion products behave like an ideal gas when they expand into the volume of the hole.

Jan 1, 2003

By Young-Dong Cho, Yonghun Jong, Dong-See Shim, Seokwon Jeon, Chung-In Lee

The most important operation in the tunnel blasting procedure is to create an opening in the face in order to develop more free surface in the rock mass. This operation is highly dependent on the cut holes. In general, the burn-cut or V-cut is commonly adopted to blast the cut section. But, these traditional methods often raise problems. There are instances (a) that the actual advance is considerably less than the designed advance depending on the rock mass, (b) that they cannot sometimes enlarge the free surface efficiently and (c) that the blast vibration resulted from the cut blast exceeds the allowable vibration level. In order to resolve the problems, many different kinds of the cut blast can be considered.

Jan 1, 2005

By James Rowland, Marcia Harris, Richard Mainiero, Michael Sapko

All explosive materials produce a cloud of reaction products, the most toxic of which is nitrogen dioxide (NO2). In the study reported here, 4.5-kg (10-lb) charges of blasting agent confined in either thin-wall 10-cm (4-in) diameter galvanized pipe or 10-cm (4-in) schedule 80 seamless steel pipe were detonated in a closed chamber. The detonation gases were analyzed for NO2, nitric oxide (NO), ammonia (NH3), hydrogen (H2), carbon monoxide (CO), carbon dioxide (CO2), nitrogen (N2), oxygen (O2), and methane (CH4). Data were evaluated to determine the kinetics of the oxidation of NO to NO2. Analysis revealed that the only mechanism for NO loss for the conditions existing in the chamber was the reaction 2NO + O2 6 2 NO2. The rate constant was 2.08 ?? 10-38 cm6 molecules-2 sec-1 for the rate equation -??d [NO]/dt = K ?? [NO]2 ?? [O2] for NO concentrations up to 100 ppm. The rate constant is in agreement with that recommended by Baulch, Drysdale, and Horne (1973).

Jan 1, 2006

By Terra Dinamica, Frank Lucca

This paper discusses blast design for vibration control in tight construction blasting. Topics include blast pattern geometry, blast design formulas, loading, explosives & initiation selection, and utilizing borehole deviation equipment and lasers, and rules of thumb. The paper will also explore vibration prediction, neighbor relations, and related topics, such as blast plan submittal. Various projects from metropolitan construction blasting operations will be used as examples. Examples include blasting in the inner city, next to pipelines, and in housing developments.

Jan 1, 2005

By V. Sastry

Signgareni Collieries Company Ltd. is operating the JK Opencast Project, at Yellandu, with a rated annual capacity of 1.6 Mt of coal with an average stripping ratio of 4.3. This opencast coal project has three working sections, OC-II block, C-Block and D-Block These workings are operating in close proximity to the JR-5 Longwall Shed, 26-Dip Incline, other structures of 26-Dip, and a Township. There were complaints about ground vibrations and fly rock problems caused due to blasting operations, especially in OC-II and D-Blocks. In view of this, studies were taken up to eliminate the problems of ground vibrations and fly rock.

Jan 1, 2001