Search Documents

By Shih Wen Wang, Ronald R. Rollins

A blast casting model is proposed to predict the burden velocity in bench blasting. This blast casting model is the first theoretical model that 1) explains the throwing procedures and mechanisms, 2) uses the explosion pressure as the primary source in throwing rock fragments, 3) applies them to field conditions successfully. Also the predicted burden velocities are based on the rock properties, the explosive properties, and the drilling and initiation patterns. This blast casting model is programmed into a computer software "ROCKFRAG". The comparisons between "ROCKFRAG" predicted values and two field test data are in good agreement.

Jan 1, 1992

By Dale S. Preece, J Paul Tidman, Stephen H. Chung

A discrete element computer program named DMC_BLAST (Distinct Motion Code) has been under development since 1987 for modeling rock blasting (Preece & Taylor, 1989). This program employs explicit time integration and uses spherical or cylindrical elements that are represented as circles in two dimensions (2-D). DMC_BLAST calculations compare favorably with data from actual bench blasts (Preece et al, 1993).

Jan 1, 1998

By R W. Givens

This paper discusses emulsion performance and characteristics. Also presented are pattern design equations by a weight strength method, a "Q" factor method, and a coupled energy powder factor (CEPF) method. Pattern expansion by replacing ANFO with emulsion is presented along with quality control checks for emulsion products. The predicted performance of the calculated burden and the equivalent powder factor as a function of the emulsion percentage, as determined by the three methods, is compared. Field results indicate that of the three methods the weight strength is the moot conservative, the "Q" is overly optimistic, and the CEPF more accurately predicts the effect of coupling and is more consistent with a variety of emulsion and heavy ANFO products.

Jan 1, 1989

By Calvin Konya, Janos Foldesi

A bridge over a main line railroad system was scheduled for demolition. The bridge was made of reinforced concrete and spanned three mainline railroad tracks which could not be shut down due to blasting or demolition. To further complicate matters, the mainline tracks had high tension power lines running above the tracks, but below the bridge. These high tension wires provided the electricity for electrically powered trains. The tracks could not be damaged or disrupted, nor could the power line be broken.

Jan 1, 1992

By Calvin J. Konya

Many controversies and differences of opinion exist in blasting technology. The primer location in small diameter dynamite columns is an example of one of these controversial areas. It is generally agreed that in rotation firing of small diameter blastholes, primer placement near the bottom of the borehole is beneficial since it reduces the likelihood of cutoffs. The controversy results in the actual location of the primer in the bottom of the blasthole. Some references indicate that the primer cartridge should be the first cartridge in the bottom of the hole, with the cap pointed toward the collar of the hole. Others indicate that performance is improved with no sacrifice in safety by placing a tamped cartridge first in the hole, and the second cartridge being the primer. The following investigation provides some factual data for consideration.

Jan 1, 1980

By Thomas A. Simpson, Yung-Kwaun Jow, Dennis L. Gamble

Construction of the $200 million Riverchase Galleria Mall in Hoover, Alabama was started in early 1984. The construction area consists of about 70 acres. The extensive building complex requires heavy concrete foundations which have to be poured during the early stages of construction and on a nearly daily situation so that contractual agreements can be met on a timely basis.

Jan 1, 1985

By Robert Lee, Jay Rodgers, Kirk Whitaker

The time domain during which an explosive detonates and causes rock to fragment and displace is on the order of tens of milliseconds. Because of this, the dynamic processes that occur during this time frame often become a source of confusion when trying to analyze the performance of explosive products in decked blast designs. As an illustration, the authors have experimentally examined explosives malfunction in decked blasts through state-of-the-art measurement techniques. The interaction of explosive products and blast geometry was examined in detail using the analysis of a series of decked blastholes. Explosive and initiator malfunction in decked blasts is often considered to be entirely the result of insufficient inert decking material, however, it is shown that rock properties and dynamic burden conditions may have a significant impact on decking performance. The successful application of deck-blasting technique for control of ground vibration amplitude relies on an understanding of the true dynamic performance of the blasthole.

Jan 1, 2000

By David Leidel

A major characteristic that distinguishes modern society from its predecessors is the understanding that events are not driven by the whims of the gods, pre-ordained fate or nature, but are controlled to a greater or lesser extent by the actions, (or inactions), of people. The study of risk assessment is the basis for determining risk or the likelihood of an event occurring combined with the consequences of that event if it does occur. This study is indubitably linked to the mathematics of probability and statistics which permits the quantification of risk. As the Industrial Revolution significantly increased the exposure of persons to new types of energy sources, materials, equipment, and means of more rapid transportation of goods and people, quantitative risk assessment became a vital tool in protecting workers and the general public exposed to these new technologies.

Jan 1, 2007

By Jiang Han, J. F. Shao

Based on the rock blasting engineering, The Self-Organizing Map (SOM) network has been implemented for the concept and method of rock blastability classification. The Self-Organizing Map (SOM) is a neural network algorithm which is especially suitable for the analysis and visualization of high-dimensional data. It maps nonlinear statistical relationships between high-dimensional input data into simple geometric relationships, usually on a two-dimensional grid. The mapping roughly preserves the most important topological and metric relationships of the original data elements and, thus, inherently clusters the data. SOM allows easy data fusion enabling visualization and analysis of large databases of rock blasting engineering. As a case study, the classification technique based on SOM has been used to classify the rock mass blastability rank. It can be founded from this paper that the SOM networks can be developed well based on a comprehensive data set of rock blasting engineering.

Jan 1, 2002

By Cam Thomas

"Reflectorless laser survey equipment has made it much easier to take accurate measurements toinaccessible locations in quarries, open pit mines and rock slopes. Prior to the introduction of thereflectorless laser as a working tool, it was not possible to directly measure to inaccessible locations on rock faces. If a person could not occupy the point, only indirect measurements could be made. For blasting work, measuring the burden in front of the first row of holes could only be done approximately, using such techniques as holding a plumb line in over the crest, triangulating in on a few points or “eyeballing” the burden. This led to direct and significant problems with blasting, including flyrock and airblast (caused by insufficient front row burden), excessive vibrations, problems with oversize and tight digging (all of which may be caused by excessive front row burdens)."

Jan 1, 1999

By Randall M. Wheeler

Many blasting companies are using simulated production ground vibration waveforms to aid them in the control of their vibration effects. The simulations are typically produced by using a seismograph to record a signature waveform from a single hole shot and subsequently applying the various delays to be used in a proposed production design. The ability of this simulation method to give good results usually depends on three primary factors. These are: 1) the homogeneity of the seismic travel path from hole to hole; 2) the consistency of the seismic energy release per unit of explosive from hole to hole; and 3) whether or not the delays fire as planned.

Jan 1, 1991

By Richard J. Mainiero, Michael S. Wieland, Harry C. Verakis

The Bureau of Mines, U.S. Department of the Interior, has been conducting research on delay blasting in underground coal mines in support of the efforts of Mine Safety and Health Administration (MSHA), U.S. Department of Labor, to revise coal mine blasting regulations. Part of the research centered on developing an understanding of the factors that lead to misfires of permissible explosives. Research was conducted to determine whether frequency of misfires was related to borehole spacing. For a wide variety of permissible explosives, misfires were observed for about 50 X of the holes at 45-cm (18-in) spacing. Misfires were also observed for 60-cm (24-in) spacing, but the frequency of misfires was much lower than observed for the 45-cm (18-in) spacing. The Bureau has recommended that hole spacings of less than 60 cm (24 in) be prohibited.

Jan 1, 1986

By W. J. Birch

The recording of information is critical to the blasting process, whether it be for planning purposes, statutory requirements or environmental compliance. The review and analysis of past data can play a key part in a blast.s design. Statutory records must be held to preserve operational licenses and well-maintained monitoring records are a vital defence for today.s litigious society. However a single blasting event can be responsible for generating vast amounts of data. This information maybe collected pre or post-blast and in their individual ways may have a requirement to be logged, processed, analysed, reviewed and reported before eventually being archived.

Jan 1, 2002

By Justus Deen, Paul V. Sterk

Through the 119 year history of the Homestake Mine various methods of raise mining have been used, these include conventional, bored, and drop raises. These raises provide passage for men and supplies, provide ventilation, transfer broken rock from level to level, and serve as emergency escapeways. As the 1980’s came to a close, many of the larger ore bodies in the mine had been mined out. This has resulted in many crown pillar situations that required a method to mine them. In addition, the Homestake ore body also contains numerous ore reserves that have short vertical height. The ore itself can be from vertical to 50 degrees in dip. Due to the high cost of drift and ramp development many of these ore bodies are subeconomic using conventional mechanized cut and fill mining.

Jan 1, 1996

By Don Rapp, Rufus Flinchum

Air blast and flyrock are two of the most critical concerns facing the blaster of today. This paper will provide the blaster with proven procedures for recognizing open face and bench surface problems, explain various surveying methods, and provide the mathematical formulas for calculating and designing proper hole placement and explosive load configuration. A concept called "Pattern Footage" is utilized in conjunction with a USBM study to develop blast designs aimed at minimizing air blast and flyrock. In addition to this main focus, this concept can be used in shot displacement and cast blasting design.

Jan 1, 1993

By Michael Swisdak, John Tatom, James Tancreto

In 2002, testing was proposed to generate needed data to assist in developing improved explosives safety standards within the US Department of Defense. This testing emphasizes two major areas: (1) full-scale donor/acceptor trials examining debris generation and acceptor response and (2) debris perforation testing of representative roof/wall materials. The full-scale donor/acceptor trials are referred to as the SciPan series. The first three tests in the SciPan series have been completed, as has the first phase of the SPIDER program. This paper describes the status and future of these testing programs, reasons for choosing specific tests, potential benefits, and planning for future phases.

Jan 1, 2006

By P D. Katsabanis

The phenomenon of sympathetic detonations in blastholes is investigated by comparing experimental observations and numerical modelling results. Numerical modelling using the TDL computer code and Forest Fire decomposition rates for commercial explosives has shown the importance of blasthole diameter, impedance of stemming material and host rock. Comparison with experimental observations has also shown that sympathetic detonations cannot always be treated as shock to detonation transitions (SDT). Examination of previous results which have been obtained from calibrated low amplitude shock experiments reveal that there is an ignition threshold prior to the detonation threshold. The difference between the two thresholds is more pronounced in the case of air bubble sensitized products. The ignition threshold can be very important under the confinement provided by the blasthole and the conditions of application. It also correlates well with the pressures expected at the gap distances of interest in the practical application. It is suggested that critical energies are used as the criterion for cross initiation in blastholes. Practical suggestions based on the numerical calculations and experiments based on these calculations are also given and discussed.

Jan 1, 1992

By Richard J. Mainiero, Marcia L. Harris, James H. Rowland

In the past several years, there have been a number of blasting-related carbon monoxide migration incidents. In each case, there have been some common factors that appear to be related to carbon monoxide migration. Geology, heavy confinement of the blast, close proximity to the affected structure, and open pathways into the affected structure are just a few. Prince William County, VA is an area undergoing a boom in suburban development. In the year 2001, more than 4,050 new homes were constructed within the county.1 In the new housing development located in Bristow, VA, trench blasting was utilized to excavate proposed sewage and utility lines. On November 8, 2002, a trench blast was conducted for the installation of utility lines. Later that evening a carbon monoxide detector alarmed in a nearby house. The gas company and fire department sampled for carbon monoxide and measured 100 ppm and more than 200 ppm on the first floor and in the basement respectively. Subsequent efforts to prevent migration of CO into the nearby homes met with mixed results. The only reliable technique for protecting neighbors from CO appears to be the placement of CO monitors in the homes. The events are presented and discussed.

Jan 1, 2004

By Richard J. Mainiero, T S. Bajpayee

The Bureau of Mines, U.S. Department of the Interior, has developed test procedures and criteria for evaluating explosive reactivity of explosive contaminated solid waste substances generated by U.S. Army Ammunition Plants. These substances are produced as explosive-contaminated sludge from waste water treatment plants, residues from the burning of munitions and explosives on open ground, and residues from deactivation furnaces. The characterization of explosive reactivity is a prerequisite for disposal of such waste materials, which may be contaminated with primary explosives, propellants, or pyrotechnic materials. The Bureau has proposed two tests for this purpose. These tests were developed to evaluate the explosive reactivity as defined in Title 40, Code of Federal Regulations, Part 261.23(a)(6) and (7). These are Bureau of Mines Gap and Bureau of Mines Internal Ignition tests, which determine the sensitivity to shock and thermal stimuli, respectively. This paper also includes gap and internal ignition reference data for typical blasting agents, high explosives, propellants, and marginally reactive substances. These reference data were used to establish test criteria. The Bureau has evaluated over 400 samples of contaminated soil, sludge, and burning residues using these two test methods.

Jan 1, 1988

It has been common practice for many years to predict and control underwater blasting effects on the basis of certain simplified theories related to the pressures generated by underwater detonations. Unfortunately, two of the most commonly applied concepts in many instances do not provide an accurate modeling of typical field conditions nor the potential for damage. One of these concepts is that the damage potential is related directly to the peak pressure generated by an underwater detonation, without regard to the time history of the pressure pulse. This belief has led to the widespread use of air bubble curtains to reduce peak pressures, without considering the effect that air curtains have on the time history of the pressure pulse. At times, this procedure can be unwise. The other concept is based on the premise that pressure pulses in solids (such as rock) will always be transmitted to nearby water bodies in agreement with the theories of the transmission of plane waves across normal (perpendicular) boundaries. In reality, such conditions are quite rare.

Jan 1, 1985