Search Documents

By P. J. Baguley

The model has been developed on the basis of the observation that the partitioning behaviour of a particle is related to its calculated terminal velocity. It utilises a theoretical calculation of the terminal velocity of each particle class. This is then correlated with the observed partition data for a plant separator using empirically-derived functions of operating conditions which take into account effects such as bath turbulence, holes in drum lifters and feed arrangements. The model successfully decouples the effects of medium density and viscosity and is appropriate for any bath-type separator. The correlation between calculated terminal velocity and actual partitioning behaviour was established and modelled using data obtained from two Wemco drums treating Fe and Mn ores. The model can be used to predict the prevailing size-by-size partition curves and the separation (product grades/recoveries) given the washability of the feed and operating conditions. Simulations are used to show that, for the treatment of Fe ore, there is a maximum medium density beyond which product grades fall and that this maximum decreases as the proportion of magnetite in the medium increases. This is attributed to the dominant effect of viscosity at higher medium solids concentrations

Jun 18, 1905

By D. Witchard, G. C. Penny

An important conclusion of the study is that altering the properties of the granulation water is a practical way of improving the sintering performance of blends that contain porous ores, and more work is under way to investigate other additives. Previous studies of iron ore blends containing pisolite ore showed that losses in sintering productivity were a result of deteriorating green-bed permeability. Pisolite ores are extremely porous and absorb a proportion of the water added during granulation. Although increased water addition could be used to counteract losses in productivity, the current study examined methods of inhibiting water absorption by pisolite ore as a means of improving productivity. Additives were used to alter the properties of the granulating water. With no increase in mix moisture contents pilot-scale sintering studies showed that sugar-based additives gave productivities that are higher than those obtained for a comparable ore blend containing haematite rather than the pisolitic ore. Several techniques of adding the sugar to the sinter mix were examined and found to increase productivity to varying degrees. Theoretical considerations, in some cases supported by experimental results, indicate that sugar-based additives not only inhibited water absorption by porous ore particles but also improved the permeability of the sintering bed. The study also suggested that, contrary to some commonly held views, the highly reactive nature of Yandi ore from Western Australia is beneficial for sintering. Porous ores enabled the formation of a strong sinter at fast flame-front speeds-both good strength and a short sintering time are requirements for high-productivity operation

Jun 18, 1905

By M. L. Leblanc, J. F. Burzynski, D. J. Mossman

A strong heterogeneity in the distribution of Sb+/-Au deposits exists within the North Atlantic Acadian-Hercynian domain. This is reflected in the regional disparity in Sb production among the various producing countries. This work focuses on the nature and distribution of Sb+/-Au occurrences in the Acadian-Hercynian domain. A summary listing of the general features of Sb-Au deposits found in this area is given

Dec 1, 1991

By R. Lahtinen, M. Tiainen, R. Salminen

The application of similarity analysis derived from regional geochemical mapping data to the location of Ni-bearing intrusions was tested in southwest Finland, where a well-known nickel belt is situated. Samples of till from the vicinity of the Vammala and Kylmakoski Ni-Cu deposits, which were collected independently of the Geological Survey of Finland's regional geochemical mapping programme, were used to provide geochemical modelling data. The data consist of the aqua regia-leachable concentrations of 20 elements from the less than 0.06-mm fraction of glacial till. The variables used in the similarity analysis were selected on the basis of a factor analysis in which the method of oblique rotation was used. A hierarchical clustering of the modelling samples produced two main groups. The first group was described as the "nickel deposit environment model" and the second as the "nickel deposit location model". The data for the standardised variables were compared sample by sample with the model data by similarity analysis using the Simana program with a cos theta measure of pattern similarity. The nickel deposit environment model delineated the known Ni belt and indicated an extension to the east. The nickel deposit location model identified target areas of reasonable size with the greatest potential for Ni ores within the nickel belt

Dec 1, 1991

By R. Poulin, C. F. Gleeson

The Birimian rocks of the region are gold-bearing and show many similarities to those of Burkina Faso. All three greenstone belts (Goroual, Tera and Sirba) host gold-bearing quartz veins. It appears that, contrary to previous misconceptions, lateritic terrain is not an unfavourable environment for exploration geochemistry. This is demonstrated by the results for the Koma Bangou area, where soil and termite-mound geochemistry have been successfully used in the search for gold. Soil provides an effective sampling medium where it is shallower than about 2 m; there is evidence that some soil anomalies are enhanced by the presence of secondary (botryoidal) gold. In areas of thicker, allochthonous soil cover, termite-mound sampling is more effective. At Koma Bangou an identified resource of some 11 100 000 tonnes with an average gold grade of 2.44 g/t has been reported. The gold mineralisation occurs in quartz veins and stockworks aand in the wallrocks of shear and fault zones that trend N, NW and NE. The host rocks are a granodiorite-syenite porphyry and intermediate metavolcanic rocks and tuffs

Apr 1, 1996

By G. J. Hearn

between particles in the classifying region is then

Apr 1, 1995

By R. A. Lord, H. M. Prichard

efficiency is discussed from both experimental and

Apr 1, 1994

By C. A. Jeffrey

The Dirtlow Rake vein deposit, which is up to 12 m thick, contains a range of paragenetically linked replacement mineralisation styles typical of many Mississippi Valley-type deposit environments. The main ore zone lies within the solution collapse breccia domes, the more southerly of which has recently been well exposed, allowing its relationship to the associated mineral-hosting structures to be studied. The domes were largely formed during early silicification, propagated by dissolution collapse and infilled by subsequent fluorite-barite mineralisation. The location of pipes and pervasive replacement was also controlled by early silicification. Structurally controlled bow tie shears were formed as a result of fluid access at fracture-bedding plane intersections. The nature and distribution of the mineralisation styles indicate that the degree of fluid access, residence time of solutions in contact with the wallrock and susceptibility of the limestone to silicification each played a major role in dictating mineralisation

Jun 19, 1905

By Seong-Taek Yun, Chil-Sup So, Seung-Jun Youm

The greisen-bordered quartz veins are spatially, temporally and genetically associated with a late Cretaceous granite intruding an early Palaeozoic, limestone-rich formation. Paragenetic data indicate three stages of hydrothermal mineralisation, the first typically in or within 500 m of the granite stock and showing vertical zoning between deeper Mo and higher W, the other two more abundant in the upper and outer parts of the mineralised area. Fluid inclusion and stable isotope data indicate that hydrothermal veins formed over a temperature range of 120-395 degrees C from low-salinity fluids. Early wolframite and molybdenite deposition in stage I occurred at temperatures of 300-395 degrees C from magma-derived, low-salinity, CO2-rich fluid, mainly as a result of fluid boiling and associated CO2 effervescence. Progressively larger volumes of local meteoric water entering the system led to the successive deposition of scheelite in stage I vugs, stage II base-metal sulphides and stage III fluorite-carbonates. Remobilisation of W and its later deposition of scheelite in the outer and shallower portions of the system occurred at 215-275 degrees C and stage II and III mineralisation from lower-temperature fluids that became progressively lighter in stable isotopes. It is concluded that the influx of meteoric water increased with distance from the cooling pluton

Jun 18, 1905

By D. Large, M. H. Davies, B. Driedrichs, U. Matzander

Synthesis report on a project carried out under the EC-funded BRITE-EURAM programme. A prototype high-resolution electromagnetic system, based on the theory of controlled-source magnetotellurics, was developed. The electrical source field is fed into the earth by dipoles at preselected frequencies and a multi-channel receiver measures five electric and three orthogonal magnetic fields. Suitable mapping algorithms and spatial filters are applied to the data and a new technique permits calibration during measurement. The system was field tested over a blind orebody, at 250-550 m depth, in the Aguas Tenidas area of the Iberian Pyrite Belt. Ten lines totalling 12 000 m of profile length were completed in seven days and the orebody was identified. Tests in the Irish Midlands suffered from strong electromagnetic interference of cultural origin

Jun 21, 1905

By D. C. Goldring

Many high-grade iron ores are considered to result from the supergene enrichment of banded iron formations. The secondary processes may be related to either present-day or ancient erosion cycles and may reach a considerable depth. Other high-grade ores hosted by banded iron formations are regarded as either sedimentary or metamorphic in origin although often also subjected to the secondary processes. The evidence for this multiplicity of origins is reviewed with descriptions of selected deposits: Kedia d'Idjil and M'Haoudat in Mauritania, Bomi Hills and the Nimba Range in Liberia, the Itabira district in Minas Gerais, Brazil, and El Pao in eastern Venezuela. Emphasis is placed on the recognition of textures that show that some ores are tectonites, the precursor materials having undergone pervasive deformation accompanied by metamorphism. The question whether such ores are pre- or syntectonic is difficult to resolve, the evidence being inconclusive, but a diagenetic/early deformation origin is preferred. The possible range of origins has to be taken into account in exploration, particularly as regards the depth of drilling, and in the characterisation of ores for metallurgical use

Jul 1, 1991

By A Cox

It has been demonstrated that all the cadmium from spent batteries, typically 4 g per battery, can be recovered by burning polyvinyl chloride waste to yield hydrogen chloride; this reacts to produce volatile calcium chloride, which can then be condensed and collected in a separate reactor. Alternatively, chlorine may be used to chlorinate the cadmium with equal efficiency. There is also a prospect of using very low concentrations of these gases, less than 1%, to effect the separation. The Cd was recovered more quickly when exposed to sustained, controlled flow rates of chlorinating gases, whereas when PVC was burnt most of the gas was produced in a very short time, not allowing complete reaction. This problem can be overcome by recirculation of the gas into the reactor. The technology is efficient and clean and the equipment used is simple, enhancing the prospects for a pilot-scale version of the process

Jun 21, 1905

By R. Ciccu, P. P. Manca, A. Bortolussi, G. Massacci

Tool performance and the unit cost of cutting depend on a number of operational variables (peripheral velocity, pull-back force, water injection rate, angles of the sections of wire outside the rock) as well as on the geometric features of the cut itself (area and shape). Cutting rate and wire productivity are also influenced by the type and number of diamond beads per unit length of wire and by the characteristics of the rock (granite or marble). A computer program aimed at handling a problem of this complexity has been developed and tested with the use of available field and laboratory data and has been found acceptably reliable. Discrepancies between current industrial data and some of the results suggest future lines of research, while the simulation should also be extended to include different types of rock and tool and a variety of bench face geometries

Aug 1, 1994

By L. J. Cabri, J. M. D. Wilson, R Lastra

An image analysis program can search for gold minerals in polished sections by scanning about 100 x 100 back-scattered electron images at a magnification of x400, allowing gold grains as small as 1 micrometre in diameter to be detected. Typically, a c.15 h overnight search of a product smaller than 45 micrometres will scan c.1 500 000 particles, providing data that are not easily obtained through manual operation of an optical microscope. The program locates grains of the correct brightness, acquires gold X-rays from them by wavelength-dispersive spectrometry, filters the data to remove artefacts and record the images and stage locations for subsequent retrieval. At the end of the run, the program allows the operator to verify and identify the grains found. Industrial studies at Canmet have included determining the nature of gold in cyanidation tailings, checking the mineralogy and size of gold grains in samples from an Indonesian Cu-Au concentrator and locating and measuring gold liberation and grain sizes in an ore

Jun 21, 1905

By Qing Wang

In this method the state of an open-pit mine is represented by the number of benches that are mined in each predesigned mining phase (or pushback). Consequently, a specific mining schedule can be represented by a sequence of states which starts with the topography of the mine site and ends with the ultimate pit. For a given set of mining phases all feasible states are first generated and sequences of states are then evaluated for technical and economical feasibility. The best sequence, which gives the maximum net present value (NPV), is found by applying a dynamic programming optimisation algorithm. The algorithm also optimises the cut-off grade which satisfies the mill feed requirement for each planning period. It was found that the algorithm can be used not only for scheduling but also as an effective tool for analysing the effects of mining and milling capacities and cut-off constraints on the mining schedule and the total NPV. The algorithm, which was programmed in C, was successfully applied to a large Au-Cu deposit

Jul 1, 1996

By G. Adachi, K. Machida, T. Ozaki, K. Murase

The chlorination rate with CCl4 was unexpectedly slower than carbochlorination using chlorine under the same reaction conditions. Chlorination with CCl4 was topochemical and the amount of monazite reacted after different periods suggested that the kinetic control step was the reaction between CCl4 and the monazite core at the interface. The kinetic order of the reaction was 0.5. The presence of a complex former, AlCl3, promoted the chemical vapour transport of rare-earth chlorides as complexes

Jun 18, 1905

By T. Lenarcic, R. Svrkota, J. M. McNeal, E. Prohic, S. Pirc

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Surface drainage samples, the usual media employed in mapping national territories, cannot be used for the geochemical mapping of carbonate terrains because there is no regular surface-drainage pattern on karst. Suitable sampling media have been studied in Yugoslavia, one-third of which consists of karst terrain. Sampling designs for the work were based on analysis of variance techniques. During initial investigations of various sampling materials in NW Yugoslavia sediment and aquatic moss from karst springs, along with soil, were established as the most appropriate media. Modified sampling procedures were then carefully applied along the entire Yugoslav karst belt, which includes terrains of contrasting topography, climate, pedology and vegetation. The studies indicate that climate and relief do not systematically influence the geochemical composition of soil. Regional and local variability was assessed for 21 chemical elements and the feasibility of producing stable regional geochemical maps was determined for a number of elements on the basis of sampling aquatic moss and sediment from karst springs and soil

Jul 1, 1991

By H. Forster, F. H. Koenemann, U. Knittel

The greenstone belt developed along the Sandawana line, an anastomosing, transcrustal shear zone. The lode gold is concentrated in veins and along brittle-ductile shear zones and other faults. Gold contents of 200 rock samples were found to be well below economically significant levels, excluding purely syngenetic deposit formation. Average gold content of unmineralised banded iron formation decreases from 7.3 ppb in the east (Manica) to 1.6 ppb in the west (Odzi), where depletion reflects hydrothermal leaching. The mineralising fluids may have been generated during deep crustal deformation, metamorphism and magmatism. Gold was hydrothermally deposited during carbonatisation and sericitisation of ultramafic and mafic rocks and during hydrothermal overprinting of banded iron formation and felsic rocks. It is present in native form and as microscopic to submicroscopic inclusions in pyrite, arsenopyrite and pyrrhotite. Argentiferous galena and other sulphides are commonly observed. Rezende, which produced over 38 t Au, is hosted by a granodiorite stock. By-product gold was produced from Cu-Ni sulphides at Mundonguara. The deposits are related to the older, but not the younger, of the granitoids intruding the belt's supracrustal sequences; the estimated age of mineralisation is 2700-2600 Ma. Odzi district, with 61 mines, has produced only 3.5 t Au as its higher-level host rocks have apparently been eroded. Mutare (formerly Umtali) district, with 133 mines and 9 placers, has produced 68 t Au (65 t from Rezende and adjacent deposits), and Manica district, with 23 mines and 8 placers, 12 t Au. Estimated reserves for the Rezende area are 20 t Au and for Manica district 4 t lode Au and 19 t placer Au

Apr 1, 1996

By A. Ersoy, M. D. Waller

The principal factors which require consideration in predicting drilling rates are the bit-type, the bit operating parameters and the characteristics of the penetrated rock. A single index is not a sufficient basis for predicting performance. A variety of rock types were drilled in the laboratory with polycrystalline diamond compact (PDC) and impregnated diamond core bits using a fully instrumented drilling rig at different rotational speeds and with a range of weights on the bit. Quantitative determinations of a wide range of textural, mechanical and intact rock properties were also made. Multi-variable linear regression analysis was then used to develop predictive models of rates of penetration from the operating and rock property data. The models have been verified by statistical tests. The analysis indicated that the models for the pin and hybrid PDC bits have potential for practical application. However, although the model for the impregnated diamond bit appears to be reasonable from a purely statistical point of view, it may not be satisfactory for drilling uses as it is based on two measures of rock hardness alone. The application of multiple regression analysis to PDC drilling performance is novel and the technique shows promise for the prediction of rock drillability with PDC bits. The ability of the technique to provide a mathematical characterisation of the performance of new drill bits in specific rocks may prove to be of value to drill manufacturers and users

Aug 1, 1995

By A. Sutton-Pratt

The African continent has been the most prolific producer of gold since mining began. Although most of this gold has come from South Africa, other countries have also been important contributors in the past. There is currently little production outside South Africa, Ghana and Zimbabwe, but the gradual globalisation of the industry over the past decade has resulted in growing interest in the region which bodes well for its future development. An outline is given of prospects and activity (or lack of it) in South Africa, Lesotho, Swaziland, Zimbabwe, Mozambique, Madagascar, Botswana, Namibia, Zaire, Tanzania, Kenya, Uganda, Rwanda, Burundi, Zambia, Malawi, Angola, Congo, Central African Republic, Gabon, Equatorial Guinea, Ethiopia, Eritrea, Djibouti, Somalia, Sudan, Chad, Libya, Tunisia, Egypt, Algeria, Morocco, Ghana, Ivory Coast, Liberia, Sierra Leone, Guinea, Senegal, Guinea-Bissau, Gambia, Mauritania, Mali, Burkina Faso, Togo, Benin, Niger, Nigeria and Cameroun

Apr 1, 1996