Search Documents

By Walter E. Vanderpool

Type 1B micropiles (Bruce and Juran, 1997) can be installed rapidly and efficiently. During an 85-day period, 536 micropiles were installed to depths of 61 meters within a site 41 meters by 43 meters. Their performance, as measured by load test, varied even where the materials, construction procedure, and installation technique were closely monitored and controlled. The variation in displacement, as measured by the standard deviation, exceeded 50 percent of the mean test-load displacement for all loads up to the maximum load applied (2670 kN). This study provides a statistical basis to predict variability with respect to the construction method, micropile materials, and installation technique. The variability of displacement at all test loads is a fundamental characteristic of this type of drilled deep foundation system.

Jan 1, 2002

By Qingwei Joshua Ong

Tension piles, also known as uplift or anchor piles, are necessary to resist uplift forces that might cause structural distress. In excavation projects, most uplift forces are developed because of hydrostatic pressures, and so tension piles are subjected to a great deal of tensile forces. Most current methods of design for tension piles completely neglect the tensile strength contribution of concrete, relying only on the steel members to carry the tensile stresses, resulting in an overly conservative design. The stressstrain behavior of the composite material of concrete and steel must be considered for a realistic simulation of tension piles. This paper will examine a case on a tension bored pile in typical soft clay to demonstrate the importance of considering the tension strength and tension softening of the concrete.

Nov 1, 2022

By Jeff Wilkinson, Brandon Walter

"A&N Electrical Cooperative provides electrical service to the counties of Accomack and Northampton along Virginia’s Eastern Shore and to Smith Island in Somerset County, Md.A&N recently worked to improve the efficiency of power distribution to a small island community and marina on Tangier Island in the Chesapeake Bay. This improvement consisted of upgrading the existing distribution substation with a new 25 kV 2-bay box distribution structure. Earth Contact Products (ECP) collaborated with PowerServices, Inc. (PSI) to design and install a helical foundation support system as part of the substation upgrade. Feasibility EvaluationThroughout the design process, A&Nworked with its partners PSI (design) andT&D Solutions (installation) to identifycost-effective alternatives. Foundationsystems considered included cast-in-placereinforced concrete caissons, precastconcrete foundations, driven steel piles and helical piles. In evaluating all of theoptions, the greatest concern was gettingthe material onto the island, followedclosely by the availability of the equipmentto install the foundations. Clearly, cost,more specifically the installed cost, was asignificant consideration and decisionfactor throughout the process.There were several limiting factors that had to be considered during the design process, the most significant of which was that all of the material had to be barged to the site. With traditional reinforced concrete deep foundations in mind, the cost for installing these piles was projected to be nearly $2,000/cu yd ($262/cu m) of installed concrete. Given that approximately 5 to 6 cu yd (3.8 to 4.6 cu m) of concrete would be required for this structure, the cost was significantly high for this project. What’s more, because the components of the concrete mix would have to be barged and then hand mixed on site, there was concern regarding both the time required to complete the piles and the quality of the installed concrete. For the driven pile alternative, the availability, or lack thereof, of equipment and material cost resulted in a total cost estimate that was more expensive than that of the concrete piling alternative. The high material cost for the piles, which was more than double than the cost of concrete, was due to the number and size of piles needed to resist the overturning moment. Ultimately, the team selected the helical pile alternative. The decision to a use helical pile foundation system was based on many factors, not the least of which was the remote location of the project site and the difficulties associated with getting material, equipment and construction personnel to the project site."

Jan 1, 2017

By Jeffrey M. Taylor, Arturo Ressi di Cervia

"Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 foot (2.44m) diameter drilled shafts with 7.5 foot (2.31m) rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at both the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts. INTRODUCTIONThe replacement Brightman Street Bridge spans the Taunton River between Fall River and Somerset in Massachusetts.The new crossing is located approximately 1500 feet (450m) upstream from the existing Brightman Street Bridge, which was built in 1908. The new mainline bridge includes nine spans totaling 1725 feet (525m). A bascule type moveable span will be located in the middle of the Taunton River and provide a 200 foot (61m) open channel centered about the 400 foot (122m) navigational channel. The bascule span, which has a span length of 409 feet (124.7m), will be a trunnion-type four leaf structure with a solid deck. A site plan is shown in Figure 1 Contract 3, which includes construction of the foundations for the East and West bascule piers, was bid on December 19, 2000 and was awarded to Modern Continental Construction Company (MCC) on January 24, 2001. MCC in turn awarded the subcontract for the installation of the drilled shafts to TREVIICOS Corporation, which started mobilizing in June of 2001.The scope of work for the drilled shafts of Contract 3 consisted in installing 18 drilled shafts in three rows on each side of the river to support the bascule piers located in the middle of the Taunton River.The foundation plan for the bascule span is shown in Figure 2."

Jan 1, 2004

By Paul Hewitt, Aaron Rastall

The New South Wales South Coast rail corridor is key infrastructure for both freight and passenger transport. Geomorphological and geological evidence suggests that land instability has been widespread throughout sections of the rail corridor, long before the first documented record of landslide activity in 1879. Major landslides occurred along a 25-km length of the South Coast Railway connecting Sydney and Wollongong because of significant rainfall events of the late 1980s. Since this time, several sites have been identified as subject to instability and treated progressively under a risk priority and safety management system. Two such sites comprise a station footbridge and overhead wiring structure (OHWS), both founded on high embankments overlying colluvial materials resulting in the structures’ potential movement and associated stability concerns. This paper presents these two sites as case studies, and discusses the project geology, geotechnical models developed, interpretation of monitoring data, and successful remediation of the rail structures using sleeved bored piles. The sleeved pile system was used to isolate bored piles, which separated the bridge foundations and OHWS from the moving soil mass to ensure the piles can carry the rail structure loads, unaffected by downslope soil movements.

Nov 1, 2022

By Ben M. Lewis, Yogesh Prashar

"The East Bay Municipal Utility District (EBMUD) is a major water utility service providing water to over 1.3 million people in the eastern San Francisco Bay Area. EBMUD manages 28 dams at 5 terminal and 23 open-cut reservoirs within a 331-square-mile customer service area. As part of a 2012 update on EBMUD’s Infrastructure Rehabilitation Plan for Distribution Reservoirs, EBMUD has decided to replace Central Reservoir, a 152.8 milliongallon open cut reservoir, with optimally sized tanks. This paper presents the results of an analytical comparison of various foundation reinforcement solutions for the proposed tanks including: Cement Deep Soil Mixed (CDSM) columns, vibro stone columns, rammed aggregate piers, and lightweight cellular concrete fill. The computational program GeoMat (www.ensoftinc.com) was used to perform simplified soil structure interaction analyses. Settlement estimates were developed for each alternative with the proposed loading and compared to an allowable differential settlement criterion established at 0.3-inches over a 50 foot length. The authors wish to present the importance of considering mat and soil interaction along with various settlement mitigation methods considered for this challenging project.INTRODUCTIONProject BackgroundCentral Reservoir is an operational open-cut reservoir located north of the intersection of 25th Avenue and East 29th Street in Oakland, California. The reservoir is bound by 23rd Avenue to the west, Sheffield Avenue to the east and Interstate Highway 580 to the north. Originally, the Central Reservoir site was a drainage swale incising into weathered bedrock formed from Pleistocene alluvial deposits. The reservoir was first constructed in 1910 by excavating a basin below grade and constructing an embankment dam on the south and cutting/filling the bedrock and alluvial deposits from the drainage swale. The main dam at the Central Reservoir site is also a DSOD (Department of Safety of Dams) jurisdictional dam and as such is regularly monitored by the EBMUD Materials Engineering Section and the California DSOD.In a 2012 update to EBMUD’s Infrastructure Rehabilitation Plan for Distribution Reservoirs, Central Reservoir was identified as a critical facility that has reached the end of its useful life and must be replaced due to: a failing panel craft lining which contains polychlorinated biphenyls in the interior coating, a roof that does not meet the current seismic code, and reduced operating levels due to potential leakage in the upper portions of the panel craft lining. Furthermore, Central Reservoir is about three times larger than required and is located at a lower elevation than other regional reservoirs in the pressure zone resulting in increased labor-intensive operational challenges and water quality operations.This project presents some challenging geotechnical demands – the site is founded on weakly consolidated Holocene Alluvium overlying weathered bedrock, the proposed structural loads are large, and the new Central Reservoir is to be placed on a pad at an elevation of 182 feet, required placement of up to 30 feet of fill over the current basin. Additionally, the project aims for a long-term foundation solution that will outlive the new replacement tanks and accommodate future site upgrades. In order to meet this goal, the differential settlement criterion for the tanks was ¼ inch over 50 feet length. Lastly, the project also aims to address EBMUD’s increasing trench spoil stockpiles by recycling discarded trench spoils as fill for the proposed tank pad."

Jan 1, 2016

By James S. Graham

Marine design and construction methods are presented on the caisson foundations for the tower piers at the Brooklyn, Ben Franklin, Delaware Memorial 1st, Tappan Zee, Walt Whitman, Throgs Neck, Verrazano Narrows, Delaware Memorial 2nd, and Newport Bridges. All of the bridges are founded on caissons, bearing on bedrock, soil, or piling. Caissons at the Tappan Zee Bridge are partially supported by piling and partially by buoyant forces. General subsurface conditions for each are provided. The purpose of this paper is inform engineers how bridge foundations using caissons were built over major waterways in the Northeastern USA in the past, anticipating a surge of new bridge construction in the near future.

Jan 1, 2013

By Cem Altuntas

This paper is the second in a series of two describing the design and construction of a foundation for a major high-rise real estate development on the west side of Manhattan, N.Y. The foundation members consist of large-diameter rock-socketed caissons, driven closed-end steel pipe piles bearing on rock, and a secant-pile retaining wall surrounding the entire site. This paper focuses on the Osterberg cell (O-Cell) load test completed for determining the allowable side-shear resistance between the concrete and the sides of the rock socket. Different qualities of mica schist bedrock, demonstrated by the penetration of rock with the soil auger or drill casing, were encountered. Accordingly, an additional subsurface investigation consisting of test borings at each caisson location was completed. Unconfined compressive strength tests were performed on representative rock samples. The ?soft? mica schist was observed to have vertical foliations and high mica content. For the first time in Manhattan, an O-Cell load test was performed to determine the allowable side shear resistance for both the soft and hard mica schist bedrock. The side shear resistance obtained from the O-Cell load test is compared with the side shear resistance allowed by the New York City Building Code and empirical correlations using unconfined compressive strength values for rock. The rock socket design for the caissons was refined based on the O-Cell load test results.

Jan 1, 2008

By Garland Likins

High strain PDA testing has become common for verification of capacity of both driven and bored piles. It is equally applicable to Augered-Cast-in-Place (ACIP) Piles. It also evaluates other aspects of the installation such as integrity. The benefit of high strain dynamic test results for the relatively low cost of the tests compared to conventional static testing has resulted in widespread use. The method is described and specific procedures for testing ACIP piles are outlined. Example results demonstrate the application.

Jan 1, 2000

By Lucian Bogdan

On many occasions during construction and service life of the structure, it is crucial to know the load in post tensioning tendons and anchors. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive and the accuracy differs depending on the method used Dyna Force sensor uses the Elasto-magnetic technology (EM) and non destructive testing (NDT) to direct measure stress level in prestressed strands or bars installed on ground anchors or post tensioning tendons. Dyna Force sensor can be used to rapidly read the change in load during proof and performance tests and compare with the pressure gauge and during the life on the anchor to monitor existing lock-off load. It can be used also to determine the load along the bonded length of the anchor allowing the contractor to increase or decrease this length. The paper presents Dyna Force operating principle and some applications. In conclusion, the Elasto magnetic technology applied through Dyna Force is a new and easy to use approach to monitor anchor load during proof test and service life of the structure.

Jan 1, 2009

By G. W. Plant

This paper describes the design philosophy and construction details of piles between 25m and 32m deep to support 160m high and 110m base diameter cooling rowers for a major power station. It is sited on deep expansive soil where a vast plantation of Eucalypts had been felled. The depressed water table is expected to rise, leading to swell of the soil and uplift forces on the piles. These forces, combined with the complex loading from the cooling towers, led to design tensile loads up to 20MN (2 000 tons) per pile. When competent stable material was present hand excavated underreams 3m in diameter were constructed for the piles sup-porting the shells. However, in some areas it was not possible to form an effective underream and an innovative solution was sought. This comprised unstressed dowels in the underlying sandstone which were formed by percussion drilling through void formers cast into the piles.

Jan 1, 2010

By Alan Alhadeff

Why is mediation being hailed as the wave of the future? The high cost of putting on a trial, over-crowded court calendars and long trial delays have resulted in what prominent attorneys and leading jurists are calling a litigation crisis. In no segment of the legal world are these pressures greater felt than in the trial of the serious construction case. Furthermore, the siege mentality of both the plaintiff and defense bar often leads to a reluctance by either side to make the first reasonable offer for fear of showing weakness. Attorneys operating in the serious construction case arena express concerns that there exist insufficient opportunities for the parties to meet, tell their stories, and negotiate settlement prior to the eve of trial. Mediation, by opening lines of effective communication and encouraging meaningful settlement negotiation, has proven to be a very effective antidote to the litigation crisis.

Jan 1, 1990

By Michael W. Oakland

Weidlinger Associates was retained to evaluate the foundations supporting ten oil storage tanks at a tank farm on the east coast. The tanks were constructed over the site of a landfill which was underlain by deep organic deposits. The tanks were typically 48 ft. in height and ranged in diameter from 60 to 150 ft. The tanks were supported on both wood and steel pipe piles. After more than 35 years of service, an inspection found that up to 25 percent of the piles had separated from the mat foundation. The operations at the facility were temporarily stopped pending further investigation. Weidlinger developed comprehensive finite element models of the foundations for each tank and used random generators to conduct Monte Carlo simulations the range of scenarios of detached support conditions since it was not possible to survey all the piles below the tanks. To confirm the modeled performance and verify stability, each tank was also load tested using water with electronic instrumentation installed by Geo-Instruments. The instrumentation provided real time, web based monitoring during testing in areas which would otherwise be inaccessible during loading. Through inspection, complex modeling and sophisticated load testing, Weidlinger and Geo-Instruments were able to show that all but one of the tanks could safely be put back into service. This paper details the analysis, Monte Carlo simulations and instrumentation and load testing performed for this unique project.

Jan 1, 2009

By Bruno Vingiani, Alessandro Bertero

"The use of Artificial Ground Freezing (AGF) for temporary soil strengthening and seepage control is an effective alternative to grouting when dealing with soils whose degree of finesses would imply the use of highly expensive chemical grouts. However, compared to grouting, the application of this improvement technique usually needs a more accurate preliminary soil investigation campaign and a design assisted by specific calculation software. Besides a general description of the main features of this technique, the paper will describe a recent application of AGF carried out in Rome to underpass an existing metro station.INTRODUCTIONNatural ground freezing occurs seasonally or permanently (permafrost) in some areas of the globe close to the poles and can negatively affect the engineering performance of underground structures. On the other hand, Artificial Ground Freezing (AGF) is man-made controllable freezing process that can be used in foundation engineering to temporarily strengthen the ground and create a barrier to the passage of groundwater. During the process, the heat is extracted from the soil in a cylindrical shape around a number of freezing pipes installed into the ground. This action produces columns of frozen soil, which expand gradually till they merge and create continuous frozen wall. The thickness of this barrier can be regulated according to the specific project requirements. Nowadays, AGF technique is applied to a wide range of foundation engineering problems where soil stability and groundwater flows are an issue (Pimentel et al. 2011, Haß and Schäfers, 2013). Typical applications include the temporary stabilization and waterproof of the ground around the excavation profile of mined tunnels until the construction of the final lining (Figure 1).The case history described in this paper deals with a recent application of AGF carried out during the construction of metro Line “C” in Rome. Specifically, this technique has been applied to allow the construction of two single-track mined tunnels running underneath an existing metro station belonging to Line “A”. In that case, the AGF has been evaluated by the Designers as the only possible solution for improving the mechanical and hydraulic characteristics"

Jan 1, 1900

By Jim Glider, Noah Miner

The Gordie Howe International Bridge is a project to build a cable-stayed bridge and border crossing across the Detroit River. With a span length of 2,800-ft (853.4 meters), the Gordie Howe International Bridge will have the longest main span of any cable-stayed bridge in North America. Each tower has two legs that are supported by six drilled shafts each for a total of 12. The tower shafts are 9.84 feet in diameter (3-m) and extend well into bedrock. 17 each, 6.6 feet (2-m) drilled shafts were built to support the aging river bulkhead and replace shipping bollards. In addition to shallow groundwater fed by the Detroit River, artesian conditions at depth result in a water head that is approximately 17.2-ft (5.2-m) above surface. At 95-ft (29-m) below grade Dundee Limestone, of the Detroit River Group, is moderately weathered and fracture density decreases with depth. The Dundee Limestone strength ranges from 8-ksi (55.1-MPa) to 12-ksi (82-MPa) and may carry hydrogen sulfide in fractures. Working through casing that sticks three stories out of the ground is less than ideal, but was necessary to maintain a positive fluid head and prevent artesian-related quality issues. The sheer scale of the bridge forces required a load test configuration that could impart an equivalent static load of over 38,000,000 pounds (170-MN). A suite of QA/QC tests was developed to ensure the shafts would meet the project plans and specifications to include critical base cleanliness criteria. Interesting CSL and TIP results obtained highlight the strengths and weaknesses of each test method. Cleaning drilling fluids with a centrifuge allowed recycling of product and reduced exposure to environmental contaminate exposure. Having large construction equipment working next to the river presented challenges in working pad design. A driven pile system was developed to support high oscillator forces and protect the aging seawall.

Sep 8, 2021

By Jack Hayes

The design and construction of deep foundations involve many uncertainties. For the designer there are uncertainties regarding soil and ground water variability, regarding sampling and lab testing, regarding analytical techniques and regarding construction technique. The latter being the uncertainty over which the engineer has least control and which may have the greatest impact on capacity. Foundations with a high design factor of uncertainty can be very costly. Foundations designed with a high factor of uncertainty may have a low factor of safety, which can be even more costly.

Jan 1, 2000

By Roderic A. Ellman

The new Woodrow Wilson Bridge (WWB) will replace the existing bridge over the Potomac River to connect Alexandria, Virginia to Prince Georges County, Maryland. The new WWB will extend approximately 1.1 miles across the river, with a 367-ft long bascule span in the main river channel where the water depth is about 36 ft. The bridge is primarily comprised of fixed spans in relatively shallow water and a bascule span over the navigation channel. The subsurface soil profile was quite variable along the bridge alignment. In Virginia, there was fill over soft Alluvial deposits underlain by dense Terrace deposits, as well as remnant foundations from a former ship yard. At the bascule span, there was up to 50 ft of a soft organic silty clay layer underlain by a deep deposit of stiff Cretaceous clay. Along the Maryland approach, there were Alluvial deposits over dense Terrace deposits over stiff Cretaceous clays and dense Cretaceous sands. The variation in subsurface conditions led to the selection of alternative deep foundations that suited the specific conditions and were based on the design phase testing program, from which ultimate design capacities were determined. During construction, there were instances of unexpected pile performance, notably different than that experienced during the design phase testing, requiring changes to the contract installation criteria and re-design. This paper will present the types of deep foundations used for the project, the performance criteria assumed during the design, the measured performance and difficulties encountered during construction, and the resulting remedial actions, i.e., changes to contract installation criteria and/or re-design due to the unanticipated field conditions.

Jan 1, 2009

By Gokhan Inci

Stability problems with dam spillways on existing landslides and appropriate mitigation measures to remedy them are ongoing concerns for geotechnical engineers. The first successful application of drilled piers as stabilizing structures under the spillway was at the Trinity Dam in Sicily, Italy. ?Underpinning? was considered as an alternative to spillway relocation during the Alpaslan 2 embankment dam design in eastern Turkey. Based on the available literature the first application of drilled piers to stabilize a spillway chute in the U.S. was at the Ralston Dam in Colorado. Ralston Dam, which is a 175-foot-high zoned fill dam located 15 miles northwest of downtown Denver, was built in the late 1930s. The concrete spillway for the dam was built on the Pierre Shale Formation in the left abutment. Since reservoir operations began, mass movements have occurred downstream of the chute area. These movements have required periodic spillway maintenance. After the occurrence of recent movements and because of high piezometeric levels, URS was contracted by Denver Water to develop a more permanent solution by the installation and monitoring of additional instrumentation, analysis of slope stabilizing measures, design, repair, and reconstruction of the distressed section of the spillway chute. With state of the art modifications that include: 1) a stabilizing berm with a toe trench that improves the global stability; 2) seepage prevention and control measures that prevent the infiltration of water; and 3) the structural support of the replaced chute section with drilled piers and reinforced concrete the probability of future displacements or other problems have been reduced for the Ralston Dam Spillway.

Jan 1, 2007

By C. O. Riggs

Geotechnical exploration in North America, in particular, exploration for deep foundations analyses, is currently and generally performed following the most basic sampling and insitu testing methods and techniques. Some would surely say that the state-of-practice severely lags the state-of-the-art. Probably more than 90% of all deep foundations, both driven piles and drilled piers, installed in North America are initially analyzed and designed, i. e. geotechnically, on the basis of either the soil penetration resistance obtained by performing the "Standard Penetration Test" (SPT), or from laboratory shear tests performed on samples obtained using 76-mm (3-in.) nominal diameter, thin wall, "Shelby tube" samplers. The use of design data obtained with other exploration methods and devices, such as bore hole pressure meters, flat plate dilatometers, even cone penetrometers, occur on the fringes of practice and often in conjunction with the use of the two simpler methods of analysis. This basic approach probably represents an attempt of the profession to use, as much as possible, common, easily understood and easily communicated procedures in all geologic environments. The characteristics of drill rigs with the required drilling and samplng tools vary somewhat from region to region in North America according to the physiography of the area of use, the types of exploration data required on a day-to-day basis, the philosophy of the engineers and geologists that use the exploration data and the financial resources of the drill rig owner. The physical capability of the exploration drill rig used on a project can have a significant effect on the quality of samples or insitu tests. The physical configuration and the quality of the drill and the drilling, sampling and testing tools not only provide the mechanical capability to obtain data but affect the attitude of the field exploration crew and the quality of work. This complete presentation is taken, for the most part, from a book in preparation for publication: "Geotechnical Exploration and Site Characterization" by C. Riggs, A. Hatheway and N. Schmidt. The book is scheduled for completion during 1987.

Jan 1, 2010

By G. Ranjan

The designers and the practicing engineers have started using latest and cost effective techniques of ground improvements which utilise the weak and poor sub-soil deposits efficiently for the civil engineering construction. In the present investigation, a new concept of 'skirted granular piles' has been advocated. An effective method of construction of granular piles as an economical alternative to vibroflot, and the skirt has been developed. The construction technique is based on indigeneous know how which effectively utilises the man-power technology avoiding import of costly equipment suiting to the developing countries. Full scale insitu tests have been carried out at four sites, having different soil conditions, on virgin weak sub-soil, and improved ground by casting plain and skirted granular piles. Effectiveness of different types of skirt has been demonstrated through insitu tests. A simple analytical approach has been proposed to predict the ultimate pile capacity. The predicted values of ultimate capacity have been found to demonstrate a good correspondance. Granular pile behaviour in terms of pile depth, diameter, spacing and stress deformation characteristics of the improved ground have been discussed. A significant improvement in ultimate capacity in improved ground has been noted. This is further augmented when granular pile group is skirted.

Jan 1, 2010