Search Documents

By C. Michael Morgano

Static tests are costly and time consuming, so they are not always the best answer [ ]

Jan 1, 2005

By Mike Muchard

STATNAMIC load testing augmented with embedded instrumentation has been successfully used to obtain structural and geotechnical design information on large diameter spun cast concrete cylinder piles on many large marine construction projects. The paper focuses on one particularly interesting large marine project involving a new bridge to St. George Island, Florida where instrumentation and STATNAMIC load testing was used in conjunction with static load testing on high capacity piles. The information presented includes embedded instrumentation measurements taken during pile fabrication (post-tensioning), during pile driving, during static load testing, and STATNAMIC load testing. As much of this data is the first of its kind on concrete cylinder piles, it is exciting to present the foundation industry with this additional insight as to the behavior of this pile type and the accuracy of the methods used to test them.

Jan 1, 2013

By Chris L. Powell, Russell J. Denny

"The remotely located Cockatoo Island iron ore mine off the Kimberley coast in the northwest of Western Australia has been in operation since 1951. The mine was recently expanded up to about 50 m (165 ft) below sea level using staged construction to create a rockfill seawall around the open cut mining operation. Late in 2013, to allow expansion of subsea iron ore mining operations, Wagstaff Piling was engaged to install a seepage barrier through the rockfill seawall and into the underlying seabed sediments.Earlier stages of seawall construction had used a variety of different construction techniques with varied success, and the history of subsea mining on the island had been plagued with failures, including failures in the slope of the seawall itself, hanging wall failure underneath and inside the seawall, and footwall failures as the ore was mined leaving the rock face inclined at 55 degrees, parallel to the bedding. The current expansion, known as the Stage 4 expansion, was more tightly constrained by the pit geometry and available materials than previous seawall expansions that adopted clay core and sheet pile seepage barrier solutions. In Stage 4, an innovative seepage barrier solution using a grout curtain was selected to provide the necessary cutoff to allow access to high-grade ore, while protecting the mine from inundation by the sea.Seawall ConceptThe open cut subsea mining operation consisted of a 3 km (1.9 mi) long narrow pit along the south side of Cockatoo Island that extended to depths of about 50 m (165 ft) below sea level, and were exposed to the open sea on the south side of the pit. Massive tidal variations of more than 10.5 m (34.5 ft) required a seawall founded on the seabed, extending upwards to RL+13, to safely protect the pit from the high tide level rising to above RL+10."

Jan 1, 2017

By Chris L. Powell, Russell J. Denny

"The remotely located Cockatoo Island iron ore mine off the Kimberley coast in the northwest of Western Australia has been in operation since 1951. The mine was recently expanded up to about 50 m (165 ft) below sea level using staged construction to create a rockfill seawall around the open cut mining operation. Late in 2013, to allow expansion of subsea iron ore mining operations, Wagstaff Piling was engaged to install a seepage barrier through the rockfill seawall and into the underlying seabed sediments.Earlier stages of seawall construction had used a variety of different construction techniques with varied success, and the history of subsea mining on the island had been plagued with failures, including failures in the slope of the seawall itself, hanging wall failure underneath and inside the seawall, and footwall failures as the ore was mined leaving the rock face inclined at 55 degrees, parallel to the bedding. The current expansion, known as the Stage 4 expansion, was more tightly constrained by the pit geometry and available materials than previous seawall expansions that adopted clay core and sheet pile seepage barrier solutions. In Stage 4, an innovative seepage barrier solution using a grout curtain was selected to provide the necessary cutoff to allow access to highgrade ore, while protecting the mine from inundation by the sea.Seawall ConceptThe open cut subsea mining operation consisted of a 3 km (1.9 mi) long narrow pit along the south side of Cockatoo Island that extended to depths of about 50 m (165 ft) below sea level, and were exposed to the open sea on the south side of the pit. Massive tidal variations of more than 10.5 m (34.5 ft) required a seawall founded on the seabed, extending upwards to RL+13, to safely protect the pit from the high tide level rising to above RL+10."

Jan 1, 2017

By Abolfazl Eslami, Masoud Zare, Ali Asadi, Ali Abrang

"Physical small scale models for study of deep foundations can be performed in simple chambers (1g), calibration chambers (CC), and centrifuge apparatus (ng) which involve some limitations and difficulties. In recent years, Frustum confining vessels (FCV) have been developed for physical modeling of deep foundations. This device is frustum of a cone shape that applies a steady pressure on its bottom and creates a linear stress distribution along its vertical central line. A new FCV which has been built in AUT is introduced. This device has a height of 1200 mm, top and bottom diameters of 300 and 1300 mm, respectively. Through the application of bottom pressure up to 300 kPa, the insitu overburden stress conditions equivalent up to 40 m soil deposits consistent to the embedment depth of commonly used piles. Observation indicated that there is approximately a linear trend of stress distribution, and this device can create realistic overburden stress in the desired control volume along the central line. Moreover, a couple of compressive and tensile load tests were performed on steel tubular open end model piles driven in sand with length of 750 mm and different diameters and L/D ratio between 8-15. Comparison of load capacity between tested and full scale piles demonstrate a suitable conformity for similar confinement conditions. Therefore, the FCV can be realized as an appropriate apparatus for investigation of piling geotechnical behavior and examination of construction effects.IntroductionDeep foundations are designed as foundation system for supporting heavy loads, high rise and important structures. Different theoretical, numerical and experimental approaches have been developed to study the geotechnical behavior of deep foundations. Experimental methods are employed to clarify directly pile-soil interaction and because of repeatability, analogy, rapid measurement and cost efficiency, physical modeling can be realized as an intermediate technique compared to element testing and full scale load tests."

Jan 1, 2015

By Damir Dedic, Wörle. Patrick

"Soil properties within a construction project area are analyzed during the planning phase. However, it is only possible to achieve selective soil exploration, even in the case of very extensive investigatory programs, which results in a certain soil risk and uncertainties for planning and execution.Therefore, the application of monitoring systems is becoming increasingly important in the field of geotechnics. The application of suitable monitoring systems for these particular purposes provides considerable knowledge relating to the load bearing behavior of the soil and the ground anchor. Applications that present major challenges to measuring anchor forces include back-anchorages of long-lasting and very deep construction pits, construction pits in urban areas, slope and embankment supports for track and vehicular routes, port and lock structures, and uplift control. Apart from overseeing individual construction stages, monitoring systems analyze the interaction between the soil and structure throughout the latter’s entire life cycle and safeguard the functional capability of the applied system components. Geotechnical construction projects can be adapted, optimized and carried out with enhanced safety from the information obtained.Conventional Monitoring SystemsThere are numerous approaches for determining anchor forces of bar or strand anchors. Lift-off tests and measurements with load cells are the most common methods.Lift-off Test: Lift-off tests provide a possibility to monitor the prevailing force in strand or bar anchors. The entire anchor head structure is lifted using the appropriate equipment. The steel tendon is prolonged, or in the case of strand anchors, a screw-on cap holds the wedge carrier so that a tensioning jack can be mounted above it. Then, the tendon is prestressed until the lower anchor nut (bar) or wedge carrier (strand) is lifted off from the anchor plate. The intersection of the two straight lines in the figure represents the force at which the anchor nut or the wedge carrier lifts off from the anchor plate. Thus, the intersection displays the actual load of the anchor. This form of anchor force control gives conclusive results, but at the same time requires extensive accessories and extra personnel to execute the test. For this test, a sufficient bar overhang must be available, the wedge plate must possess an external thread, or there must be a strand overhang of at least 24 in (60 cm). Furthermore, the anchor head must be freely accessible and in a position to be reached with the necessary equipment."

Jan 1, 2017

By Timothy Nelson, Simon Burnworth

"The Berkeley Art Museum and Pacific Film Archive (BAMPFA), which currently resides in a 1970s-era post-modern concrete structure just south of the University of California, Berkeley campus, was in need of a new home after an engineering evaluation revealed that the building possessed seismic deficiencies. Pressed for space, the University looked within its portfolio of properties and identified the site of the former University Printing Press facility as the place to build BAMPFA’s new home.The site was perfect; located one block east of bustling downtown Berkeley and its rapid transit station, and directly across the street from the western entrance to the UC Berkeley campus. Thousands of pedestrians pass by the site on a daily basis, thus granting BAMPFA the opportunity to reshape the corner of Center and Oxford Streets with a building that would not only welcome visitors to campus, but also serve as a creative hub for both the City of Berkeley and the UC Berkeley institution itself 1.The original museum plans, drawn up in the mid-2000s, called for complete demolition of the existing abandoned facility and replacement with a visually stunning structure designed by renowned Japanese architect Toyo Ito. Even at this point, the shoring and means and methods requirements of the project were identified as a challenging component, incorporating a shored excavation bounded on three sides by busy city streets and a fourth side by an operating bank and occupied apartment building. Furthermore, a sequenced demolition would be required for the printing press facility’s three-story Administration Building (also known as the Admin Block), one-story printing press warehouse (also known as the Press Building), and an adjacent parking structure. Degenkolb Engineers was retained at that time as the shoring engineer to design the shoring to facilitate this work."

Jan 1, 2016

By R. J. Yan

There was a plant equipped with a 32000t Hydraulic Press to be built, under which a box foundation of 22.5m x 15m x 14.25m (depth) with a base slab of, varying thickness was proposed. The subgrade reactions, bending moments and settlements needed to be determined by means of in-situ model test. A model of the same materials as the prototype scaled to l/10 was embedded in-situ with simulated depth in the bedrock. A lot of data obtained from 39 bench marks, 32 elongation measuring points, 30 couples of electric resistance strain gauges and 24 pressure cells attached to the model foundation enables all the quantities required to be found out. Since it was put into operation, the settlements measured has reasonably agreed with the test results and the foundation has been in good condition.

Jan 1, 2010

By Parameswaran V. S, Anshuman Singh

This is a case study on ground improvement using Stone columns at Kokrajhar in Assam which comes under seismic Zone V as per IS: 1893. The strata at site comprised of mostly fine sands with low SPTN values, fine content less than 10% and ground water table (GWT) at shallow depth. As ground water table subjected to seasonal variation, water table is considered at ground level for designing purpose. The geotechnical profile of the boreholes was analysed on the guidelines of IS 1893 (Part 1) -2016 and it was observed that the liquefaction potential of the soil layers is prominent and ground improvement is inevitable up to a depth of 9.5 m below existing ground level. In order to mitigate the liquefaction of soil layer, Stone columns were proposed. The in-situ soil is densified using wet top feed vibroreplacement method with an area replacement ratio of 16%, so that the relative density of the soil can be enhanced to prevent liquefaction risk. Correlation between relative density, fines content and increment of SPT N –value given by Tokimatsu and Yoshimi (1983) was used for designing purpose. Field tests such as SPTs were carried out at site to validate the extent of SPT (N) improvement. Detail comparison of pre and post density, SPT N values and CRR values were discussed in this paper.

Nov 1, 2022

By Ramin Motamed, Fahim M. Bhuiyan, Raj V. Siddharthan

Numerical lateral load analysis based on the beam on Winkler foundation (BNWF) model (i.e., the p-y method) is a simple, and widely used tool to predict lateral responses of drilled shafts from field load tests. The lack of a site-specific p-y model for cemented soil layers such as caliche is one of the major limitations of simulating lateral load tests conducted in Las Vegas Valley. In this study, some of the existing p-y models for rock materials, such as Florida Limestone and Vuggy Limestone have been evaluated to simulate the lateral resistance of caliche. This has been done in the context of four lateral load tests in caliche-dominant sites from the recently constructed Raiders Stadium project in Las Vegas (NV). The uncertainty in characterizing the material properties of caliche has been addressed. The p-y analyses were performed using NVShaft, a MATLAB-based, comprehensive load analysis program. The applicability of the considered p-y models for caliche material was evaluated by quantifying the normalized error margins between measured and predicted lateral responses from the simulations of the mentioned load tests. Correlations between such errors and the depth and thickness of caliche in soil layers affecting numerical predictions were established, for both up to and beyond design load levels.

Oct 1, 2022

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees is applied to a 0.61 m flagpole and a 0.61m fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil is represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2011

By Soorkty Elarabi

The aim of this paper is to discuss the impact of end bearing plate on the capacity of micropile. Preliminary studies have been made in Sudan in specific area of cohesive soil. Experimental works were carried on a number of micropiles with and without end bearing plate. Same diameters, lengths and techniques of placing cement grout are considered, there after the axial load test applied to find out the capacities of micropiles in both cases. Deduced results in each case show that the end bearing plate has no positive impact on micropile capacity.

Oct 1, 2022

By Noreen Tarac, Pablo Forgoso, Philipp Schober

A multiple use storage facility building is being developed in the Philippines on a peninsula that was reclaimed in the 1990s without any soil treatment. The subsoil now consists of loose to medium dense silty sand underlain by a soft to medium stiff clay. A liquefaction assessment by analytical methods have shown that the loose to medium dense silty sand yields a high potential for liquefaction and lateral spreading during pthe design level seismic event. To mitigate the risk of liquefaction and lateral spreading, as well as assure the slope stability of the shoreline, a solution utilizing a combination of ground improvement techniques by means of a Mixed-In-Place (MIPTM) Lattice Grid Wall and Stone Columns was developed and successfully executed. For the detailed seismic design, a Finite Element 3D analysis was undertaken to simulate static and dynamic actions on the buttress wall. The liquefaction assessment and settlement calculation were carried out based on analytical design approaches. For the execution of the Lattice Grid Wall, the Mixed-In-Place (MIPTM) method developed by BAUER Spezialtiefbau GmbH was applied. The stone columns were installed using the Wet Top Feed method.

Sep 8, 2021

By Chandrasegaran, Tamilmani

"This paper describes a case study of a retaining wall structure using a diaphragm wall to construct a stilling basin at Tanjung Bin T4 power plant in Johor Bahru, Malaysia. The stilling basin is part of the Phase IV (T4) 1x1000MW power plant’s offshore cooling water discharge culverts. The site is located close to the sea with 5m of fill on top of very soft sediments of marine origin up to 20m thick underlain by fluvial clay and metasedimentary rock. Stringent wall deflection criteria and construction program dictated adopting an efficient solution with 800mm thick diaphragm wall supported by permanent top support as the temporary prop and improved horizontal restraint provided by deep mix piles acting as a slab (ground improvement layer) below the final excavation level. The depth of excavation is about 10.12m from the existing ground level. The proposed solution kept the wall deflection below the limit of 0.7% of the depth of bulk excavation and avoided additional props leading to faster completion of the structure. With unsymmetrical loading behind the retaining walls, 2D finite element analysis was carried out to assess the wall deflection and stresses in the wall and the grout layer below. The diaphragm wall is instrumented to monitor the behavior and the findings are discussed in the paper.INTRODUCTIONConstruction in soft marine clay has always been a challenge to the engineer because of its very low shear strength and its sensitivity to disturbance. In the case of excavation projects the problem becomes even more complicated with development of excess pore pressure during excavation. Marine clay with its low shear strength and lesser passive resistance, generally leads to large wall movements and settlement behind the wall. Increased passive resistance coming from increased number of props is useful but has its limits and it is no longer the most effective way in containing or reducing the wall movements or forces in the wall. One of the solutions to these problems is to improve the soil shear strength by means of ground improvement infront of the wall at an elevation most appropriate to maximize wall performance. There are several methods adopted in improving a soil layer including mixing additives to the ground to improve the shear strength to partially replacing the weak soil while others are fully replacing the weak soil. This paper discusses the case study of approximately 10m of excavation in soft marine clay using 800mm thick diaphragm wall supported by Deep Mix Piles (DMP) being used to improve soft marine deposit to form a slab just below the formation level and thus improving passive resistance significantly. The ground improvement layer helped to reduce the wall forces and deflections making it possible to remove the need for additional temporary props leading to significant savings is time and productivity. The paper presents the various options explored before this method is adopted, the design approach, instrumentation data and the monitored results."

Jan 1, 2015

By K. Rainer Massarsch

"Part 1 of 2 By K. Rainer Massarsch, Geo Engineering AB, Stockholm, SwedenINTRODUCTIONConstruction activities, such as driving of piles and sheet piles, soil compaction or excavation generate noise and vibrations. In populated areas these can have a negative impact on the environment, disturb inhabitants and, under unfavorable conditions, cause damage to buildings and installations. This condition is aggravated by the growing public awareness of environmental issues and the increasing use of vibration-sensitive electronic equipment and machinery in industry. In many countries, environmental regulations are enforced more stringently and limit or even prohibit the use of impact or vibratory hammers. This development has restricted the use of cost-effective foundation methods, such as driven and vibrated piles and sheet piles.Vibration problems are gaining importance in many European countries and extensive research has been performed during the past decade, especially with respect to traffic vibrations (Massarsch, 2004). Significant progress has been made owing to the availability of high-quality field measurements and an improved theoretical understanding of how vibrations are generated and transmitted through soil layers. These findings can also be applied to vibration problems associated with construction activities. However, this information is not yet appreciated by the geotechnical profession and even less by the construction industry.This paper discusses the effects of ground vibrations on the surrounding soil and on buildings, with particular emphasis on the different mechanisms of damage that may occur. Guidance is given on the elements which should be taken into account in an assessment of risks associated with piling projects. A simplified method is proposed for assessing the risk of settlements or strength loss in soil deposits. Limiting vibration levels are presented, based on the Swedish standard, which can be used to assess the risk of damage to buildings. Aconcept to predict ground vibrations caused by pile driving and the mechanisms which control the propagation of ground vibrations, will be presented in the second part of this paper."

Jan 1, 2004

By Mario Mauro

Tuttle Creek Dam was constructed by the U.S. Army Corps of Engineers in the 1950?s on the Big Blue River in north-east Kansas. Since the dam is located in a seismic area, the safety of the dam was re-evaluated under the national U.S. Army Corps of Engineers Dam Safety and Assurance Program. After a series of studies and analyses performed by the Kansas City District of the U.S. Army Corps of Engineers, in 2003 the Department of the Army authorized the implementation of the plan ?Stabilize Foundation Soil without Drawdown Alternative?, during a 7-10 year construction period. As part of this plan, in 2006 Treviicos South carried out a large scale jet grouting and deep mixing test program downstream the dam. The test program included the installation of twenty-seven double and triple-fluid jet grout columns and twenty-seven jet-assisted deep mix columns. The jet grout columns were constructed at different levels of specific energy and cement content. The deep mix columns ranged in diameter between 3 ft and 6 ft. During column placement, the drilling and grouting parameters, pore pressures, and soil movements were instrumented in real-time. The downstream test area was enclosed by a cement-bentonite wall extended to bedrock, which allowed a 35-ft deep open excavation around the 45-ft deep columns. The exposed jet grout columns measured up to 15 ft in diameter, exceeding the anticipated target diameter. In addition to coring, some of the jet grout and soil mix test columns were saw-cut along the group axis, providing useful information on the internal column structure.

Jan 1, 2008

"1.0 INTRODUCTIONThese Guidelines reflect the state-of-the-practice of the Deep Mixing Method (DMM) in North America. DMM is an in situ mixing process that breaks down the soil structure; injects binders, fillers and reagents into the soil; and blends them with the soil. DMM is also commonly referred to as Soil Mixing. The final properties of the treated soil in situ are a function of the composition of the native soils and groundwater, the binders introduced, the mixing methods and energy, and the conditions and time of curing. Treated soils generally have increased strength and stiffness and/or reduced permeability relative to the native soils.This document addresses DMM performed by rotating single and multiple axis mixing tools, rotating cutter wheels at the end of a rigid kelly bar, or trench mixing using a rotating cutting/mixing chain around the perimeter of a rigid bar. Binder may be injected through low or high energy (velocity) jets.The treated soils created through wet DMM are heterogeneous mixtures of binder, water, soil, and groundwater. Treated soils produced by dry DMM techniques are a mixture of binder, soil, and the water already present in the native soil.DMM applications described in this document include•,Earth retention•,Liquefaction mitigation•,Groundwater seepage control and containment isolation•,Bearing capacity improvement•,Deep foundations•,Mass stabilization and contamination containment•,Embankment, levee and dam strengthening, and stabilization•,Casing replacementThis document was developed to address deep foundations applications. Use of deep mixing for seepage control is not specifically addressed. The reader is referred to documents prepared by the U.S. Army Corps of Engineers for additional information. Shallow soil mixing and the use of DMM for stabilization/solidification of contaminated soils performed at depths less than 10 feet (3 m) are mentioned briefly. Jet grouting is not covered by these guidelines."

Jan 1, 2016

By Kiyotaka Ohno, Nobushige Yasuoka, Yosuke Hioki

"The diameter of improved columns adopted by the original DJM Method had been 1000 mm, however, in order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter expanded to 1300 mm was developed between 1998 and 2001 and has been widely applied since then. From the first application of EX-DJM in January 2002 for a first construction project, the total volume of improved soil has reached 325,000 m3 in 17 projects up to September 2014. Because of the advantages of the EX-DJM such as reduction of construction costs and periods leading to reduction in the number of improved columns, adoption of this method is expected to increase in the future. This paper describes the advantages of the EX-DJM, its construction results and case examples including those applied to restoration projects after the Great East Japan Earthquake, 2011.1. BACKGROUND OF DEVELOPMENTThe Dry Jet Mixing (DJM) Method is a soil stabilization method in which a powdery or granular binder is pneumatically fed into and mixed with soft soil to induce chemical reactions that stabilize and strengthen the soil. It was developed by government - private collaboration in Japan between 1977 and 1979. Up to March 2014, the total volume of soil improved by DJM method reached 33,500,000 m3. The initial diameter of improved columns of the original DJM Method was 1000 mm. In order to comply with the social need for construction cost reduction, the Expanded Dry Jet Mixing (EX-DJM) Method with maximum column diameter 1300 mm was developed between 1998 and 2001.2. ADVANTAGES OF EX-DJMThe construction equipment for the EX-DJM consists of two major parts, which are DJM machine and binder plant are shown in Fig. 1.The construction machine is of double mixing-shaft type with its column diameter expanded to 1200mm or 1300mm. In association with the increase in the column diameter, the binder feeder has also increased its discharge rate by approximately 1.69 times. Same as the increase rate of the area of original diameter 1000mm to diameter 1300mm are shown in Fig. 4."

Jan 1, 2015

By Dileej M. Dewaikar, Poonam A. Patil

"In this paper, the ultimate lateral resistance of a long, flexible, unrestrained vertical pile in a cohesive soil is computed under static loading condition using py curves. A simple and improved method for the construction of hyperbolic p-y curves for a cohesive soil is proposed for static loading conditions. An iterative analysis is employed with secant modulus approach, using a matrix method known as moment area method developed by Sawant and Dewaikar. The loadground line displacement relationship is obtained for different load eccentricities using p-y curves developed by Matlock, Georgiadis et al. and the proposed hyperbolic p-y curves for different eccentricity ratios. These values are compared with the values computed from model test performed by Rao et al. and with the limit equilibrium solution given by Broms. The comparison shows that, the results obtained using hyperbolic p-y curves shows a better agreement with the model test data with the maximum difference within 15% using other methods; whereas Broms' limit equilibrium solution shows some agreement with the results based on Matlock's p-y curves.INTRODUCTIONPile foundations are used for jacket type offshore structures, which are subjected to large magnitudes of lateral loads due to lake or ocean waves, winds and ice forces. The failure of a pile-soil system is catastrophic and excessive deflection of the pile creates operational difficulties. In the view of this, bending moment in the pile is required to be predicted in a rationar manner. The p-y concept developed by Reese and Matlock (1956) is popularly being used to estimate the pile top deflection and bending moments.The ultimate lateral load which causes collapse of a pile-soil system is generally estimated using Broms' (1964) method, which is based on limit equilibrium considerations. The p-y curves are basically nonlinear in nature and include ultimate pressure at the depth where they are generated. Therefore, if the lateral deflection of pile top against different magnitudes of lateral load is obtained, it should be possible to obtain the ultimate lateral load from this load-deflection relationship."

Jan 1, 2005

By Frédéric Rocher-Lacoste

On July 2nd, 2007, LCPC and LOADTEST performed a static loading test with an Osterberg-cell on a bored pile of 1600 mm diameter. The 56.50 meters deep test pile constructed by Trevi Spa for Soares da Costa group, was near the Cacheu river in Guinea Bissau. This test was conducted to validate the design of the foundations of the Sao Vicente bridge; a project undertaken by the Ministry of Public Works of the Republic of Guinea Bissau and funded by the European Development Fund. Sub-surface conditions at the test pile location consist primarily of layers of weak sands and clays. The piles were loaded statically using the O-cell® bi-directional method 25 days after concreting. The maximum sustained bi-directional load applied to the pile was 11.7 MN. At the maximum load, the displacements above and below the O-cell assembly were 6.6 mm and 81.9 mm, respectively. The resulting pile head behavior has been calculated for a combined skin friction and end-bearing load of 29.3 MN. The piles were also instrumented using LCPC removable extensometers, which made it possible to measure the mobilization of shaft friction and toe resistance. The adjusted test data indicated that this pile would settle approximately 12.2 mm for the service load of 12MN applied at the head of the pile. This paper provides a very brief presentation of the bridge project and the test pile instrumentation: LCPC removable extensometers and O-cell® instrumentation. The results are detailed and analyzed herein and the combined use of these two instrumentation systems is a world première.

Jan 1, 2008