Search Documents

By Christian Divis

[ ]

Jan 1, 2002

By Anne Lemnitzer

Full-Scale cyclic field testing was performed on a 3x3 pile group consisting of nine cast-in-drilled-hole (CIDH) reinforced concrete shafts and a comparable single-shaft in order to investigate group interaction effects. Both specimens were constructed with pile diameters of d = 0.61m (2 ft), fixed head boundary conditions, and placed in stiff clayey soil at a test site near the LAX Airport in Southern California. Internal instrumentation was installed in the single pile as well as in three piles within the pile group to obtain pile curvatures. External instrumentation controlled the lateral displacement of the specimens. A combination of experimentally and analytically obtained p-y curves for the single pile was used to simulate results for piles located in the group when field data were not available. All test specimens were tested to structural failure and excavated after test completion to investigate pile damage and plastic hinge formations. Calculated group interaction factors ranged between 1.0 at very small displacement levels of <2.5 mm (0.1 in), 0.8 at the initiation of the pile-soil-pile interaction, i.e. between 4 mm - 15 mm (0.16-0.6 in), and increased towards 0.9 near structural failure (displacement >25 mm or 1 in). A literature set of p-multipliers was found to reproduce an accurate fit to the available load displacement test data from the group.

Jan 1, 2010

By K. Y. C. Chung

A case study on foundation engineering through organic soils is presented. Located along the west shore of the Hudson River, site soils consist of random brick fill over a thick layer of peat and organic silts or clays. The organic layer is underlain by medium dense to dense sand with varying amounts of silt. Strong artesian pressures were measured in the sand. A pile foundation system was selected to support all structures. To avoid periodic flooding, new fill must be placed on the existing fill. Large total and differential settlements will occur due to consolidation and secondary compression of the organic soils. This settlement will reduce the allowable pile capacity due to the large negative skin friction in the organic layer; and will necessitate long-term maintenance of the final grade elevation. Pile load tests were performed to determine the allowable compression and uplift capacities, long-term capacities and pile driving criteria.

Jan 1, 2010

By Aly M. Mohammad

State and federal agencies during rehabilitation of existing bridges may require the existing bridges to be evaluated under seismic conditions. If the bridge does not perform under the seismic event, the bridge may require seismic retrofitting. Bridges are classified as: Critical, Essential, and Others according to their importance. Geotechnical considerations play a major role in evaluating the bridge behavior under a seismic event. Subsurface conditions influence the magnitude of ground acceleration and hence the forces and moments on the superstructure. This paper will provide a detailed description of the geotechnical aspects associated with the seismic retrofit evaluation for the 12th Street and 14th Street Viaducts located in Jersey City, New Jersey. The paper will also present a description of the geotechnical investigation program including seismic cross-hole surveys to determine the dynamic soil parameters, including the results of site-specific response spectra for both the 475 and 2475-year events. Liquefaction assessment methodology utilizing an equivalent factor of safety will also be described and the design method used will be summarized. In general, the pile foundation is modeled as 6x6 foundation stiffness matrix with 36 stiffness coefficients at the center of the pile cap. The seismic loading on the foundation is evaluated in a pseudo-static analysis, where the dynamic earthquake-induced loads are presented by static forces and moments. The computer program FB Pier was used to evaluate the foundation stiffness. The moments, axial loads, and shear are input into the FB Pier model. The stiffness of the foundation is determined and the results are then input into the Structural model to determine new forces and displacements. Adjustments are made until the loads are compatible with the stiffness used. The understanding of the geotechnical conditions at the 12th Street and 14th Street Viaducts and the coordination between the Bridge and Geotechnical Engineers were able to provide significant cost saving to the Owner. The Design Engineers were able to retrofit the existing Viaduct foundations with reasonable number of additional piles. It is believed that the results and finding presented in this paper will benefit both the Bridge Engineers and Geotechnical Engineers by highlighting the importance of interaction between the two disciplines.

Jan 1, 2006

By John E. Lens

Minutes after the Friday afternoon October 16, 2009 announcement that the 80 year old Lake Champlain Bridge was closed to traffic out of concern for public safety, emergency detour planning started at VTrans and NYSDoT. The closure severed a cross-lake link between Addison, VT and Crown Point, NY, which created a 76 mile detour and significant hardship for commuters, farmers working on both sides of Lake Champlain, and businesses relying on both traffic and employees commuting between Vermont and New York. Rehabilitating the bridge was determined to be economically and technically unfeasible and the design of a replacement bridge was accelerated for a spring 2010 construction start. In the meantime, a temporary ferry alternative was to be rushed into service beside the original bridge by February 2, 2010. This paper presents the case history of the fast-tracked ferry dock design and construction on the Vermont side. Twin 300-foot-long pile supported approach spans, a loading slip system and ice deflectors were designed, fabricated and constructed in 90 days in the fall/winter of 2009-2010. This chronicles the project from initial concepts through the extraordinary cooperation between state and federal agencies, and near round-the-clock winter construction on Lake Champlain. This project and its companion project on the New York shore succeeded by virtue of exceptional cooperation between seasoned regulatory, design, and construction participants and warrant this case-history presentation of the Vermont project to share within the industry as an example of overcoming extraordinary challenges.

Jan 1, 2011

By Harald Ludwig

In 2002, excavation support work commenced on the Capitol Visitor Center project located adjacent to the nation?s Capitol building in Washington, D.C. The outlying work (Slurry Wall Work at Main Site is not discussed) consisted of providing excavation support for a new truck tunnel approximately 1900 feet long up to 50 feet deep as well as support for the new underground auditorium and Library of Congress tunnel. The excavation support consisted of a combination of conventional drilled in soldier beams, lagging, tiebacks and braces; intricate underpinning inside the existing Capitol building; support of an existing Russell Tunnel; soil nailing and tiebacks underneath the existing Russell Tunnel; two temporary bridges; and a deep soil mixed wall with lateral support provided by braces. As part of an on-going research program, some of these braces were instrumented with strain gauges. The deep soil mixed wall was approximately 300 feet long and 65 feet deep on either side of the truck tunnel. Approximately 34,000 sf of deep soil mixed wall, 90,000 sf of conventional excavation support, 200 braces, and 320 tiebacks were installed. This paper describes the large scope and breadth of the project that required a variety of excavation support techniques. A few of the challenges in designing and installing the support of excavation are discussed. This paper also presents the results of the instrumentation program conducted on the deep soil mixed wall, which stood open for more than a year.

Jan 1, 2006

By Thomas Lardner

Excavation for The Bow, EnCana, in downtown Calgary, occurred between May 2007 and September 2008. A monitoring programme was used to determine the behaviour of the shoring wall, soil and bedrock during the excavation for the 21 metre (69 ft) deep excavation with a footprint of approximately 17,000 m2 (183,000 sq ft). Results from the inclinometer readings indicated that significant horizontal movement due to a weak rock layer and shear band effect. These modes of movement account for up to 100 mm (4.0 in) and 45 mm (1.8 in) of lateral deflection, respectively. Based upon the results of the monitoring programme, rock samples were collected from the weak mudstone bedrock, with great difficulty, to determine the strength and deformation parameters. Results from the uniaxial compression tests indicate a UCS around 830 kPa (120 psi) and elastic modulus between 80 and 180 MPa (11 and 26 ksi). Mohr-Columb parameters were determined to be c&apos; = 340 kPa (49 psi) and f&apos; = 24°. Residual strengths were determined to be c&apos;r = 0 and f&apos;r = 15°. Using the results of the laboratory tests and field investigation records, an initial finite element analysis was conducted. Results of the analysis show good correlation when compared with the observed monitoring deformation, indicating accurate portrayal of rock parameters. Additional analysis and investigation is required to determine the principal horizontal stresses in magnitude and direction.

Jan 1, 2010

By Francis J. Arland

The installation of augered cast-in-place (ACIP) piles requires careful quality control to assure a successful pile installation. Unlike steel, pre-stressed concrete or other types of driven piles, which are shop fabricated, delivered to the site and typically driven to a minimum tip resistance, augered cast-in-place piles are installed to a pre-determined tip elevation or to a refusal criteria. The structural section of the ACIP pile is constructed during pile installation and cannot be inspected prior to installation. Therefore, a carefully administered quality control program is essential to a pile foundation that will meet or exceed design requirements. This requires an experienced team consisting of the Geotechnical Engineer, Contractor and Inspector. The focus of this paper is to discuss the responsibilities and duties of the ACIP piling Inspector. Qualifications of the Inspector The qualifications of the inspector are related to the complexity and difficulty of the proposed project. Ideally, the Inspector should be an individual with a degree in civil engineering with special emphasis in geotechnical engineering. A properly trained technician with geotechnical engineering experience working under the direct supervision of a geotechnical engineer may be able to provide competent inspection on some projects. It is important that the Inspector have a good understanding of subsurface and ground water conditions and how they will affect pile installation. The Inspector must understand ACIP pile installation procedures and be able to communicate with the Contractor, Structural and Geotechnical Engineers; and maintain a detailed pile record for each installed pile.

Jan 1, 1997

By Mark R. Svinkin

Construction vibrations may be harmful to adjacent and remote structures, sensitive instruments and people. Construction vibration sources have a wide range of energy, displacement, velocity and acceleration transmitted on the ground. Effects of different dynamic sources and soil conditions on construction vibrations is analyzed. Consequences of construction vibrations are developed in various ways. It is important to assess intolerable vibrations before the beginning of construction activities. Guidelines for preconstruction survey are presented. Pre-construction survey and prediction of anticipated vibrations by IRFP method, monitoring and control of measured vibrations are important steps in preventing intolerable vibration effect.

Jan 1, 2000

By B. Ladanyi

The design philosophies for piles in unfrozen and frozen soils are compared, and their similarities and differences are underlined. It is shown that in frozen soils, the long term behavior of a pile is difficult to predict, because of inadequate knowledge on the behavior of adfreeze bond with time, and on the value and variation of the lateral normal stress acting on the pile. Both of these problems are discussed in the paper on the basis of laboratory tests and theoretical analyses.

Jan 1, 2010

By Dominique Vié

Standards methods covers the procedures for testing deep foundation to determine the force and velocity response to an impact of a pile driving hammer or similar device. The results of analysis generally include an assessment of pile integrity and the value of maximum dynamic stresses. But evaluation of static bearing capacity remains a matter of individual engineering judgment. A new 1D finite elements model has been developed for dynamic stresses and velocity analysis. Following an international benchmark of bearing capacity prediction organised by the Belgium Building Research Institute (BBRI), 12 piles in a site of fissured stiff tertiary clay tested in 1999, and 12 piles in a site of dense sand tested in 2001, comparison are proposed between analysis of dynamic tests and static tests results. A procedure is proposed to take in account the results of dynamic test for evaluation of bearing capacity.

Jan 1, 2002

By Leonardo Massone

The p-y method is one of the most popular methods in pile design and has been calibrated for various boundary conditions using numerical and experimental studies during recent years. Most studies on reinforced concrete (RC) piles have included the impact of flexural nonlinearity, (e.g. nonlinear moment?curvature relations) but not considered associated pile shear deformations when deriving p-y curves from field data. Common p-y curves may be better applicable for piles with flexure dominated failures (e.g. piles with free- head boundary conditions). For piles with fixed head boundaries (i.e. rotation restrained piles) shear deformations could be of significant influence. To study this problem, a coupled shear flexure interaction model for axial-bending-shear behavior coded in OpenSees was applied to a 0.61 m (2 ft) diameter flagpole and a 0.61m (2 ft) diameter fixed head pile specimen to investigate the possible influence of shear deformations to the overall pile responses. The surrounding soil was represented by p-y curves derived from prior large scale testing on piles with similar boundary conditions. Analysis results show that for flagpole piles, shear forces and shear deformations were insignificant. Considerable contributions of pile shear displacements and forces were observed for the fixed head pile, with shear displacements contributing up to 40% of the total pile displacement. Results suggest that nonlinear shear deformations for reinforced concrete piles should be considered for fixed-head or similar conditions, and that currently used p-y curves may underestimate the actual lateral pile displacement and possibly lead to unsafe design for the particular boundary condition.

Jan 1, 2012

By Robert A. Field

Static-Load Piledriving utilizes a hydraulic push to facilitate the installation of a pile. The pile is not rotated, impacted or vibrated. A smooth pushing force advances the pile incrementally into the ground. Static-Load devices must have a reaction mass to push against. The most simple form of a Static-Load device is a jack; more advanced equipment, such as the Still Worker, also utilizes this approach. This paper focuses on the use of the Still Worker on three challenging projects. In each case, the existing site conditions made it risky, or unattractive, to utilize conventional impact, vibratory, or drilled-shaft equipment.

Jan 1, 1997

By Jim Steding

L.G. Barcus and Sons, Inc. recently completed a three-phase project for the expansion of Presbyterian Hospital in Albuquerque, New Mexico for McCarthy Construction Co., the Construction Manager for the project. It was a challenge that allowed Barcus to demonstrate many of it&apos;s strengths. Safety of people and property, restricted access, low headroom conditions, extensive planning to maintain hospital operations and a tight schedule were all key elements affecting the successful installation of the Augered Cast-In-Place Piles. Phase I began with installing and performing a 450-ton pile load test on an 18-inch diameter Augerpile 65 ft long. The load test was installed and performed directly in front of the Emergency Room entrance. Space was limited and the E.R. had to remain open with uninterrupted ambulance access. The results of the load test were outstanding. In fact the test pile performed so well that some of the job piles were shortened from 75 ft long to 65 ft long. [ ]

Jan 1, 2003

By Martin J. Kenwright

Within the famous Harrods department store, a new lift shaft has been constructed, servicing a depth of 22m below ground level as well as the existing 6 storeys of the store. The shaft will connect with a new goods tunnel which is to be excavated beneath the shop, as well as new floor space above ground level which has resulted from the infilling of a previously existing lightwell within the store. The construction of the deep shaft while maintaining uninterrupted use of the store by the Client led to a number of innovative solutions being undertaken. Empirical assessments were made of settlements anticipated from the construction process, which took place within a congested environment of existing foundations. Various elements were designed and installed to mitigate the effects of the inevitable ground movement on the surrounding overlying structure, which supported sensitive high quality finishes and mechanical and electrical installations. The reinforced concrete lining of the shaft was contained within a cofferdam of minipiles. The minipile placement accuracy (1 in 150) was vital as it could not interfere with the subsequent tunnelling works. As the scheme progressed this became even more critical since the minipiles were needed as support for parts of the permanent works. This paper describes:- the high quality placement and control of the minipiled cofferdam, the methods employed in assessing ground movements and the techniques used to mitigate against the effects of these movements.

Jan 1, 2000

By J. Nakayama

Down-the-hole hammer is commonly recognized as the most powerful drilling equipment for weathered to fresh rock formation including boulders. However, its drilling diameter is restricted by reasons of difficulty to actualize large diameter drillhead and to ensure discharging means of cuttings. Cuttings are usually removed by flushing i.e. uprising return air after compressed air actuates hammer, but in case of large diameter drilling, as the clearance between drill rod and surrounding wall of hole become fairly large, necessary up-hole air velocity to transport cuttings can not be maintained. In case of marine or underwater drilling or high groundwater table, orthodox down-the-hole hammer is obstructed its operation by water. This single head hammer drill combined large diameter drillhead with reverse circulation of drilling fluid enables large diameter drilling extending to 1.5 m, i.e. actualized large diameter mechanical drillhead incorporated with ensured cuttings removal means enabled this range of drilling. This paper introduces its features and actual applications to large diameter bored pile drilling for varied sorts of rocks in maritime construction projects.

Jan 1, 1996

By Don C. Warrington

This paper is a survey of the various methods and research efforts by which the drivability of piles is determined. First, a brief outline of the basic theory and the important parameters for driving by vibration are presented. Then, a wide variety of methods by which the drivability of piles is determined are presented and discussed, with special emphasis on methods developed in the USSR. Each of these methods are examined as to how they take into account the various parameters of vibratory pile driving, such as eccentric moment, frequency, dynamic force, motor torque and power, vibrating and static weight, and other variables. Some relation of these methods of field data is presented as well.

Jan 1, 1989

By Patrick Bermingham

The advancement of hydraulic impact hammers has followed the general advancement of hydraulics. The construction industry has been revolutionized by the application of hydraulics in excavators, cranes and, of course, in the hydraulic vibratory driver/extractor, which has become a standard tool. The innate ability to move a large mass with a very small displaced volume has given hydraulic power the advantage over previous power mediums. Recent development of more specialized and complex seal configurations and compounds has greatly improved the reliability and permitted the use of higher pressures in hydraulic systems.

Jan 1, 1987

Jan 1, 1988

By Lee Sieng Kai

This paper presents the result of the analysis of strain-dependent concrete modulus from full-scale static axial compression load tests conducted on more than 200 instrumented cast-in-place barrettes and bored piles over the past 12 years, covering commonly adopted grades of concrete for heavy foundation construction in Malaysia and Singapore. The concrete modulus values, Ec, analysed were directly back-calculated from the material of the instrumented test piles by means of placing a layer of vibrating wire strain gauges near the pile head region. The best fit curve for back-calculated concrete secant modulus versus measured axial strain follows non-linear behaviour for both categories of test pile samples analysed. The result of the analysis seems to suggest that using average constant modulus value would generally lead to a significant error in load distribution computation, particularly at high stresses region.

Jan 1, 2006