Search Documents

By Hyunsuk Yoon, Kiho Lee, Juhyng Lee, Younghoon Jung, Junboum Park

"The environmental double pile method is presented as a device to improve the engineering properties and to clean up contamination of low-permeability soil. This method is one of the novel technologies based on the concept of one step process. It can be applied to low permeable contaminated ground for site reuse. It uses piles to improve drainage, contaminant remediation, and bearing capacity of the ground. To evaluate the on-site applicability of this technology, drainage and strength properties of the environmental double pile were assessed by a series of experiments and numerical analysis. Environmental double pile was found to be a feasible alternative method to improve contaminated soft ground.Korea is a peninsula with many coastal industrial zones. These zones are located in regions mostly underlain by soft ground with low permeability and adjacent to industrial areas that can be contaminated. Therefore, a new region-specific remediation method is required to achieve environmentally sustainable development. This research introduces the Environmental Double Pile (hereinafter, refer to as EDP) for the lowpermeability contaminated ground and focused on both contaminant remediation and soft ground improvement. Basically, the EDP is quite similar to sand compaction pile (SCP). The SCP has been studied extensively to improve soft ground (Braja 1999; Hansbo 1994; Madhav and others 1978; Taylor 1948). But unlike SCP, EDP is filled with oyster shells instead of sand and an inner pile is inserted in the center of this oyster shell filled-zone. Therefore, it is a double pile consisting of the oyster shell pile and the inner pile, as depicted in Fig. 1."

Jan 1, 2005

By David R. Shields, Michael T. Bracher

"The $330 million (U.S.) Dana-Farber Cancer Institute’s Yawkey Center for Cancer Care (Yawkey Center) sits in the heart of Boston’s Longwood Medical Area. The Yawkey Center is a cutting-edge cancer care facility that houses Dana-Farber’s adult clinical care and clinical research programs. Standing 14 stories above grade, it includes 7 stories of underground parking extending 75 ft (23 m) below ground. The structure is on a 198 by 186 ft (60 by 57 m) site sandwiched between Dana-Farber’s 13-story Richard A. and Susan F. Smith Research Laboratories Building, the Medical Area Total Energy Plant (MATEP), Jimmy Fund Way, and Brookline Avenue, a busy four lane artery through the heart of the Longwood Medical Area. Together with Simon Design Engineering, the project structural engineer, GEI Consultants designed an innovative foundation and excavation support system to isolate the building from ground vibrations generated by the adjacent MATEP power plant. In effect, the Yawkey Center is a 21-story free-standing structure that starts 7 stories below grade.The MATEP facility provides power for 9 million sq ft (840,000 sq m) of occupied space in the medical area. There are six 32-cylinder diesel engine generators in the facility that produce low-frequency ground vibrations in the 10 Hz range, similar to the natural frequency of typical building elements. The resonant response of the Yawkey Center building structure to these ground vibrations would affect the performance of sensitive medical research equipment and cause an unacceptable environment for clinical care.The soil profile at the site consists of stiff clay, fine sand, glacial till, and bedrock consisting of hard metamorphosed conglomerate. In-situ measurements of ground vibrations performed in boreholes showed that there was little attenuation of the vibrations with depth in the soil layers overlying the bedrock, but the vibration amplitude in the bedrock was markedly lower than in the overlying soil. Based on this data, an innovative foundation system was designed to support the building on bedrock located up to 110 ft (34 m) below ground surface, while isolating it from the surrounding soil. This was done by physically separating the below-grade parking garage floors from the perimeter foundation walls to create a free-standing structure supported on the bedrock"

Jan 1, 2012

By Bill Shea, Gordon King

"For a drainage channel built in San Juan, Puerto Rico, a value engineering (VE) proposal incorporating a secant pile top-down approach saved time and facilitated construction work on the larger flood control project. The channel, at the Bechara Industrial Area, Puerto Nuevo Port Facility and the Puerto Rico Maritime Shipping Authority Dock, was needed to allow drainage of the Rio Puerto Nuevo into San Juan Bay. The port area, one of the busiest in the Caribbean, has over 6,000 ft (1,800 m) of berthing wharves for ocean-going container ships along with over 500,000 sq ft (46,000 m²) of container loading and unloading areas, and is critical to the local economy.Planners wanted to minimize the impact of construction to the port and dock users, and developed a construction methodology and work sequencing that would prevent a complete barrier to port traffic. This plan involved non-contiguous and limited work area that “leapfrogged” along the alignment so as to prevent long barriers to lateral traffic movement across the culvert alignment.After reviewing the project plans and schedule, Morris-Shea Bridge Company (MSB) proposed an alternate design and construction approach that provided significant cost and schedule benefits, and also provided better access for the port and dock users. The alternate VE proposal involved top-down construction methodology and redesigned drainage culvert geometry with two parallel 2,000 linear ft (lf) (600 m) secant walls installed on each side of the culvert. These walls facilitated excavation and formed part of the culvert permanent walls. The result was a significantly reduced required construction right of way that allowed construction work in contiguous areas largely without impact on ongoing port activity. MSB conceived the design concept, and engineered design and construction of the VE alternate secant pile culvert.The project initially consisted of an open channel in the industrial area picking up water from the existing Rio Puerto Nuevo, transitioning to an enclosed culvert through the port and dock areas, and outfall through the existing dock. The base bid construction included three main areas of work:"

Jan 1, 2012

By John Erikson, Alan J. Lutenegger, Nicholas Williams

"In order to evaluate the level of disturbance produced in clays during installation, a series of single-helix and multi-helix anchors were installed at a test site consisting of a stiff overconsolidated clay crust overlying softer near normally consolidated clay. Field vane tests were then conducted over the top of the helical plates at various depths to determine the undrained shear strength after installation and were compared with undrained shear strength measured in adjacent undisturbed ground. The tests represent the first time that the degree of installation disturbance has been evaluated directly and show that even with perfect installation practice the clay is disturbed as a result of rotation of the helices during installation. The results show that the soil is not completely remolded but that the strength is below the peak undrained strength of the adjacent undisturbed ground. Measurement of the installation torque and the rate of advance are used to define an “Installation Disturbance Factor” which may help to evaluate the quality of the installation by the Contractor and degree of soil disturbance. INTRODUCTIONAn important consideration in the design of Helical Anchors is the degree of disturbance to the soil during installation. This may be especially important for saturated fine-grained soils where the disturbance from installation may produce a reduction of the undrained shear strength. Even though this was recognized as early as 1950 by Skempton, soil disturbance is often ignored by engineers using current design procedures. Field investigations were performed to obtain both directs and indirect evaluation of the degree of disturbance produced by the installation of single-helix and multi-helix anchors in clay and the influence of disturbance on behavior. The investigations involved measurement of torque and advance during installation, load tests performed to determine load-displacement behavior and ultimate capacity and field vane tests performed over the helical anchors to evaluate changes in undrained shear strength as compared to adjacent undisturbed ground. The characteristics of the site and details of the installation are presented. Results of the field vane tests are shown for a number of helical anchor installations and results of load tests are presented. The results indicate that a reduction should be made to the undisturbed undrained shear strength for design and that the reduction may be related to the Sensitivity of the clay and quality of installation."

Jan 1, 2017

By Marcus Daubner, Karsten Beckhaus, Florian Bauer

The construction industry can and needs to contribute to a more sustainable world. Accordingly, geotechnical works potentially have a significant share. In this context, Bauer understands “sustainable products for geotechnical works” as those that may cause less emissions and increase the sustainability of construction activities. In order to structure the efforts and systematically pursue sustainable targets in the construction sector, and in the specialist foundation industry, the “17 sustainability goals” presented by the United Nations in their AGENDA 2030, can be used for general guidance and for continuous improvement. Benchmarks for relevant economic and social objectives, mainly with environmental aspects, are inevitable. The key parameter to sustainable products for geotechnical works in the focus of this paper is the optimisation of processes on site needed to fulfill the client’s building task, including the selection of technologies and construction methods with minimum environmental impact and minimum carbon footprint.

May 1, 2022

By Douglas G. Baker, Jason K. Braund-Read, Megan R. Sheffer

"Mica Dam, owned by British Columbia Hydro, is an 820 ft high earthfill embankment dam that was completed in 1973. The dam consists of a thin central impervious till core supported by upstream and downstream compacted sand, gravel and cobble shell zones, founded on bedrock and valley bottom alluvium deposits. In 2012, a project was started to install new piezometric instrumentation within the dam’s foundation and downstream shell zone.Deep drilling in large embankment dams is very difficult and requires careful planning to select a methodology capable of reaching the target locations, while ensuring that no damage is done to the surrounding dam fill zones. At Mica Dam, the drilling could only be carried out from the Dam Crest and drillholes had to be carefully oriented to avoid intersecting any existing dam instrumentation. The drilling work therefore required angled drillholes, at depths of up to 855 ft, through heavily compacted sands, gravels and cobbles, and to significant depths below the standing water table.During the planning stages for the Project, in early 2013, the preferred drilling method was selected and a drilling contractor was engaged for the drilling work. Critical dam safety concerns were identified and addressed during the design stage of the Project with the drilling contractor, so that risk mitigation measures and response plans could be effectively developed.This paper explains how background information and prior drilling experience influenced the final design and implementation of the drilling techniques used in 2013 to successfully drill the deep holes and carry out the piezometer installations in Mica Dam. Drilling procedures, instrumentation design and installation methods, as well as risk mitigation measures, are discussed."

Jan 1, 2017

By Mary Ellen Bruce

Let me first address the issue of the wet grab samples. The wet grab samples that were attempted to take on the Central Artery were hindered by the fact that the way the mixing was being done was only by injecting grout on the way out, during withdrawal of the mixing tools. They would auger down to the required depth (usually with some water being injected), which took anywhere from 45 minutes to an hour, and then when coming out, the grout would be injected with grout. That was leaving a column of grout in the center where the shaft had been (i.e. inside of the blades of the mixing tools), which would end up being something like a foot in diameter because the pipe that was used for the drill shaft was a foot in diameter. So we had 10 inches to a foot of almost pure grout in the middle of our column and then we had 2 feet on either side that was mixed soil cement. So when they went down with the wet grab sampler not knowing where that was in the column sometimes they/we were getting strengths of 1500 psi, and sometimes they/we were getting strength of 500 psi or 100 psi. So what was it that we were taking into the wet grab sampler? In those cases you don't really know, but it wasn't representative of the core samples we were taking. We were purposely not coring in the center because we knew that was going to be high cement content, almost pure grout. So the issue of wet grab sampling particularly on this project, the Central Artery Project, was that we didn't really know what we were sampling. What becomes an issue with wet grab sampling in other projects is that you have to have another device (machine) in most cases, a cherry picker crane or something similar that can raise and lower with a beam that is used to forces the sampler down into the freshly mixed soil-cement. And regarding economics, is it more economical to have that crane standing by with its operator or to have a drill rig to come along later and do the coring and take the material out that's fairly identical to what you're finding in situ? The complaint of micro-fracturing in the core samples as you're taking the cores was raised by Seiko as causing large strength reductions. But, if you're doing it carefully, then I don't think that's much of an issue anymore, on research basis perhaps but not on a practical level.

Feb 10, 2003

By George Filz, Peter R. Cali

"Unnecessarily restrictive specifications could be limiting the cost effectiveness of deep mixing (DM) applications and therefore limiting use of DM on projects where there are other options. Excessively restrictive standards demanded for strength and permeability certainly increase contractors’ bid prices, and costing the owners and, in the case of Government projects, the taxpayers more than necessary. Yet, lax or ineffective specifications often exist for some vital components of the quality assurance and quality control. In this paper, specifications for key elements of DM design and construction are examined. Recommendations are made to improve and streamline DM specifications to better serve the common objective of constructing a safe and cost effective ground improvement project.INTRODUCTIONSpecifications should, at their best, convey the project design requirements and provide clear direction to the contractor regarding requirements for submittals, materials, execution, measurement, schedule, and other aspects as necessary. The specifications should not be overly conservative, restrictive or ambiguous, and they absolutely should not be deficient in measurement of quality. Guide specifications or recycled sections from previous projects often form the template for new project specifications. But standards that appear in guide specifications or from former successful construction should be critically scrutinized by the designer for relevance before using the copy/paste functions of the specifications writer’s keyboard. Because work does not always go as smoothly as planned, specifications for remediation of non-compliant construction should be clearly stated and enforced. Often, non-compliancy is reviewed after-the-fact and deemed to have met the design intent, indicating that either the specifications were too restrictive or the enforcement too weak.The Federal Highway Administration Design Manual: Deep Mixing for Embankment and Foundation Support, October 2013, was written by a panel of DM expert design practitioners and contractors. Guide specifications are included as Appendix C of the FHWA manual. Those guide specifications have been updated in the deep mixing section of the www.GeoTechTools.org website, and the updated specifications represent the most complete and authoritative compilation published to date. Although the specifications for DM at www.GeoTechTools.org are current and complete, and they portray the state-ofthe- practice, they too must be modified to fit specific DM applications, project needs, and site conditions. The keys to a good set of specifications are to prescribe construction only to the level that is required to meet the design intent, to require appropriate quality control and quality assurance (QC/ QA) activities, and to clearly address remedial measures required for non-compliant work."

Jan 1, 2015

By I. D. Dayal, Anil Kumar Jain

"Cutoff walls are frequently used to slow down or prevent seepage of water through and/or around dams. Cutoff wall is a type of seepage barrier structure designed to reduce the flow of water underneath temporary or main dam. There are number of techniques for the construction of cutoff walls including concrete, Jet grouting and permeation grouting. NHPC LTD, a premier Govt. of India undertaking has been instrumental in the hydropower development within the country & in nearby countries like Nepal & Bhutan since last four decades. NHPC LTD has completed more than 20 hydro-electric projects with total installed capacity of 6587MW (including capacity addition by JV- NHDC). In all these projects, different types of dams and spillways were constructed in not so benign to extreme challenging geological set up. There has always been challenge associated with the temporary diversion works. The project sites sometimes incur huge river bed excavations in case of concrete gravity dam founded on rock foundation at large depth. The challenges for minimizing the seepage have been well taken care by constructing the dedicated seepage barriers. The construction of cut-off walls have progressed from “conventional continuous trench backfilled with conventional concrete or plastic concrete” to “grout curtain”, to “jet grouting” to the “concrete cut-off wall” , the last being the most sophisticated & credible seepage barrier.The efficiency of the cut-off walls are monitored by the seepage quantity observed (reduction of the seepage flow), uplift pressures or exit gradients after construction of cut-off walls. For construction of the main concrete dam, required space is created by the river bed excavation for placing the dam foundation on sound rock. Sometimes there is deep river bed excavation from 30 to 40 m depth or even more as per the available rock profile. Temporary coffer dams are constructed for diverting the river flow through diversion tunnels / channels etc. In deep river bed excavation; there are high chances of the significant seepage through the coffer dam foundation / river bed material due to high hydraulic gradients. Seepage and piping are the main causes of the failure / damage of the temporary coffer dams. If the seepage quantity is too high, then it becomes difficult to handle it by dewatering in the dam pit. Dam concrete is required to be placed unhindered to have a monolithic construction of dam blocks & to have faster construction in the working season. Cut-off walls increase the seepage path considerably thus reducing the exit gradient and further reduction of the seepage thus helping in maintaining the seepage free area for working."

Jan 1, 2016

By Vivian M. Troughton, Clifford J. Wren, Tony P. Suckling

"Secant pile walls are used for the construction of deep basement walls and earth retaining structures. Risk associated with secant pile walls is commonly perceived as being the safety of site personnel and the public during piling operations, or safety used in design. It is recognized that both of these are of paramount importance, but additional risks associated with the construction methods must also be considered to complete the risk management profile for any project. For the particular case of secant pile walls, if Clients take a ""back seat"" they may be unaware of the total risk package they are procuring. The authors argue that the piling contractor should be involved at the earliest stage giving input into the overall risk management process. Such early involvement within the professional team will maximise cost benefits to the Client and minimise the delays and cost increases sometimes associated with these works. A consistent methodology for identifying and then managing all the risks associated with secant pile walls is proposed. An example is used to demonstrate how this methodology should be employed. INTRODUCTIONThis paper discusses the value of a complete and integrated risk management process for structures with basements formed using a secant pile wall.The risk associated with any secant pile wall can be consicfered as comprising four components;1. Safety of people on site2. Safety of design or design methodology3. Construction risks4. Commercial risksAny risk management system needs to fully consider and integrate each of these four components to maximise the likelihood of a successful outcome for the basement.This paper concentrates on the construction risks for secant pile walls, as these are not often understood by the Client (in this paper the term ""Client"" also includes the main contractor, principal contractor, Engineer, Planning Supervisor, quantity surveyor and cost consultant)."

Jan 1, 2005

"Integrity tests refer to a variety of non-destructive tests (NDT) whose purpose is to measure or determine the quality and uniformity, and some- times dimensions, of cast-in-place concrete foundation elements. The tests are primarily aimed at detecting zones of poor quality concrete, voids, bulges, and/or necking.The non destructive integrity testing techniques in this section most generally used for drilled shaft testing are based on one of two physical principles - stress wave propagation or nuclear radiation. All of the stress wave methods involve monitoring a deliberately created vibration, usually of very low amplitude (strains on the order of ??). Some methods rely on direct transmission of the signal, while others rely on processing reflections of the imposed signal.The stress wave methods are inherently sensitive to vibrations from other sources, especially at frequencies that fall within the range of interest for the particular test being applied. Construction activity near the shaft being tested; such as: demolition jack-hammering, pile-driving, casing vibration, excavation and movement of track-vehicles are all known sources of interference that might render test data useless. The actual effect of such vibrations will vary with the type of activity, soil conditions and distance from the testing. The test operator must be able to recognize such interference, and the contractor should be prepared to cooperate with the testing personnel by stopping or moving the source of vibration. If this cannot be done immediately, testing should be postponed until the work in question is finished and the vibration source moved or shut down.NDT methods are not suitable substitutes for routine "topside" construction inspection as described in the Drilled Shaft Inspector’s Manual. However, these NDT methods do allow measurements of the quality of concrete placed in drilled shafts, which cannot be made from "topside" construction inspection. They should be considered supplemental to routine construction inspection as they do provide an additional level of quality control."

Jan 1, 2004

By S. Chilka, I. Maloney, J. Brady

"The purpose of this project was to design the Electrical Service Platform (ESP) for the Cape Wind Offshore Wind Farm. The ESP structure comprises two primary parts: the topside platform housing the electrical equipment and the two jacket substructures providing foundation support to the platform. The topside is supported only by the two inner legs of each jacket. The site water depth is relatively shallow and the seabed comprised of loose sediment subject to severe local scour up to 18 feet. The piles are designed for local scour, storm conditions, vessel impact, ice loads and pile installation fatigue. This paper focuses on the design and construction aspect of this project.PROJECT DESCRIPTIONBackgroundThe Cape Wind project will be located in Nantucket Sound between Cape Cod on the Massachusetts mainland (northeastern coast of the USA) and the Islands of Martha’s Vineyard and Nantucket (Fig. 1). The project is to be sited on Horseshoe Shoal, about equal distances from the mainland and the two islands. The project will produce 75% of the electricity used on Cape Cod and the Islands of Martha’s Vineyard and Nantucket with zero pollution emissions and resulting in the reduced operations, fuel consumption and pollution emissions from the fossil fuel power plants in the region. The wind farm, if constructed per plan, is expected to be America’s first offshore wind farm.The wind farm will consist of an array of 130 Siemens 3.6-megawatt offshore wind turbines with a combined production capacity of 468-megawatts. The offshore wind turbine towers will be bolted onto the transition pieces supported by monopile foundations driven into seabed. The power from the 130 wind turbine generators will be delivered to the Electrical Service Platform (ESP) by an array of up to 14 seabed conductors."

Jan 1, 2017

By Richard Hanke, Franz-Werner Gerressen

"The twin decked Alaskan Way Viaduct is a passage to Seattle’s downtown waterfront and of great economic importance to the city. In 2001, the Nisqually earthquake damaged the viaduct and led to the redevelopment of this corridor. The project includes two miles of 57.5 ft diameter bored tunnel beneath downtown Seattle and a stretch of new highway and overpass bridges at the southern tunnel entrance. State-of-the-Art special foundation equipment was mobilized for the project to perform a broad range of geotechnical construction. Applications included soil mixing and jet grouting for confinement cells around new bridge foundations, large diameter secant pile walls for the Tunnel Boring Machine launch portal along with an extensive jet grouting regime for ground improvements within the tunnel alignment. This paper will study the evolution and use of advanced special geotechnical construction equipment and describe its application at the Alaskan Way Viaduct Replacement Project.INTRODUCTIONThe evolution of geotechnical construction equipment continues through innovative applications and continued modification or enhancement of machinery. Similarly and in parallel, market expectations continually demand more in terms of construction speed and performance. Together, market demands and contractor innovation have led way to the development of specialty geotechnical construction equipment with capabilities previously not seen feasible or possible. Several examples of this scenario have recently developed during design and construction of the Alaskan Way Viaduct Replacement Project.The Alaskan Way Viaduct Replacement Project is a joint project between the Federal Highway Administration (FHWA), the Washington State Department of Transportation (WSDOT), and the City of Seattle. Three build alternatives were under consideration for replacing the Alaskan Way Viaduct: the Bored Tunnel Alternative, the Cut-and-Cover Tunnel Alternative, and the Elevated Structure Alternative. Ultimately, the bored tunnel option was selected as the best value approach. The project includes two miles of 57.5 ft diameter bored tunnel beneath downtown Seattle and a stretch of new highway and overpass bridges at the southern tunnel entrance. Several other associated improvements tie into this project that will ultimately lead to the complete demolition of the viaduct and redevelopment of Seattle’s waterfront."

Jan 1, 2015

By Franz-Werner Gerressen

"New developments are required day by day. On the one hand site to improve the actual situation, on the other hand site to create the future and to ensure that future demands can be fulfilled. This requires for instance the development of technical support systems, which enable a more constant and quality ensured installation of special foundation products like piles. As part of the quality control, real time installation control of the production process, data transfer and reporting systems become more and more important ensuring the five dimensions of a jobsite. That means not only the three well known dimensions (width, height, depth) are cover, but also the dimension of time and money. Beside small, but important, details, also the demand of extending the use of methodologies in terms of getting deeper or allow their use in various soil conditions require the development of new tools and equipment. Therefore, the paper will describe some of these new approaches and activities required for these new developments. It will describe also the main equipment which will be needed to execute these works under the various conditionsINTRODUCTIONNew developments are required day by day. Either to improve the actual situation, or to create the future and to ensure that future demands can be fulfilled. Therefore, there is an increasing demand for the development of e.g. “Little Helpers”. “Little helpers” are for example technical support systems, which enable a more constant and quality ensured installation of special foundation products like piles, for example an assistance system like the later explained “drilling” assistant. As part of the quality control, real time installation control of the production process, data transfer and reporting systems become more and more important ensuring the five dimensions of a jobsite. In a second part the focus will be given to new approaches for soil mixing application. Adjustments of tools or equipment to extend the range of possible usage as well in terms of soil conditions as in treatment depth.“LITTLE HELPER”GeneralThe B-Tronic System enables you to efficiently operate, maintain, and administer individual machines as well as entire fleets. It helps you to securely monitor and precisely evaluate your projects and work processes. The system is an integrated system for controlling all operations and visualizing actual operating parameters in real-time on a large interactive touch-screen monitor."

Jan 1, 1900

By Franz-Werner Gerressen, Manfred Schoepf

"Diaphragm walls are known as underground structural elements commonly used as retention systems for excavation pits and shafts and permanent foundation walls or elements. It can be anticipated that, with the increasing trend of utilizing more and more underground space to accommodate environmental considerations and urban/suburban development, there will be an increasing requirement for diaphragm walling in even more complex conditions. Complex and/or challenging conditions in terms of ground conditions have a major impact in regards of choosing the right tools for excavation purpose. Complex conditions in terms of space limitations, especially for inner city job sites, require specifically adapted solutions for slurry, spoil, reinforcement and concrete handling and the related logistic to ensure smooth production. Furthermore, one focus will be given to the QA/QC topics of the production process. Real time installation control, data transfer and reporting systems become more and more important ensuring the five dimensions of a jobsite. Therefore, the paper will describe the construction method and the sequence of activities required for the construction of diaphragm wall systems with the focus on the cutter technology. It will describe also the main equipment which will be needed to execute these works under the various conditions INTRODUCTION Diaphragm walls are known as underground structural elements commonly used as retention systems for excavation pits and shafts and permanent foundation walls or elements. It can be anticipated that, with the increasing trend of utilizing more and more underground space to accommodate environmental considerations and urban/suburban development, there will be an increasing requirement for diaphragm wall usage in even more difficult conditions. Of course diaphragm wall can also be used as deep groundwater barriers (Cut-Off-Walls). This market has shown that the demand for these types of walls is reaching more and more difficult soil conditions or required depths which are surpassing the current standard. The trench cutter is the most important tool for performing this work. The trench cutter itself is a reverse circulation excavation tool. It consists of a heavy steel frame with two drive gears attached to its bottom end, which rotates in opposite direction around horizontal axis. Cutter wheels are mounted onto the drive gears. As they rotate, the soil beneath the cutter is continuously being broken up, removed, mixed with the bentonite slurry in the trench and moved towards the opening of the pump suction box. The slurry loaded with soil and rock particles is pumped by a centrifugal pump which is located right above the cutter wheels, up through a hose system up to a desanding plant where the slurry is cleaned and returned into the trench."

Jan 1, 2015

By Maral Papazian Bedian

"Case 2. 100th Street Bus Depot: Elimination of Deep Caissons in Favor of Spread FootingsThe PROJECTThe 100th Street Bus Depot is a new five-story bus terminal for the New York City Metropolitan Transit Authority occupying one city block in Manhattan between 99th and 100th Streets, and between Lexington and Park Avenues. It replaces a former two-story garage, built in the 1890’s and initially used as a trolley-car barn. The new structure is a steelframed building with concrete floors and includes a partial basement near its middle. The easternmost column line with design loads of 10 MN (1,125 tons) is within 1.5 m of the underlying multi-tube Lexington Avenue subway system. To support the new columns along the subway line, the project bid plans had called for 1 m diameter and 17 m deep drilled shafts. The upper 14 m of each unit would have required 50 mm separation from the surrounding rock to prevent stress from being imposed on the roof and walls of the adjacent tunnel. The column loads were thus transferred to below the base of the tunnel and supported by 3 m long sockets in bedrock. The bid documents contained extensive test boring information, which revealed that the project site was underlain by massive Manhattan Mica Schist bedrock within just 3 m below street level. In fact, the Lexington Avenue two-level and multi-tube subway had been tunneled through this rock circa 1910, leaving an about 6 m thick solid roof over the upper-level subway. The NX rock core recovery values were near 100 %, with average RQD of 75 %.The CHANGEThe Bus Depot project was let as a design/build contract with a very aggressive fast-track schedule. Both the pre-bid preliminary design and the subsequent final design by the Contractor’s own hired design engineers relied heavily on very restrictive codes, including unnecessarily conservative approaches to seismic design. Any suggestion for value engineering change was undesirable and was strongly resisted. Yet, objecting against the blind reliance on codes in foundation design, the author questioned the real need for the deep drilled shafts to support the columns along the subway. The unsupported statement that no stresses from the new structure can be imposed on the roof and walls of the adjacent tunnel was not sufficient reason for the drilled-shaft design. Unconvinced that deep shafts were necessary, the author rushed to MTA’s warehouse where many rows of rock core boxes were neatly stacked. Careful inspection and some simple testing of the rock cores with the blows of a geologic hammer gave support to the reservations about the design. Later, as expected, the schist bedrock at this site was found to be hard to very hard with unconfined compressive strength values estimated to range from at least 70 MPa to over 100 MPa (10,000 psi to 15,000 psi). The tensile strength of the rock was assessed to be minimum 5 MPa (750 psi)."

Jan 1, 2003

By Sherif Elfass, Gary Norris

Bi-directional load testing of drilled shafts has been widely adopted as a means to evaluate their load carrying capacity. However, in order to reach failure, most of these tests are carried out on sacrificial shafts using expensive sacrificial elements such as hydraulic jacks. A proposed low-cost bi-directional testing technique is discussed. It mechanically loads the end bearing soil below a drilled shaft, against its side shear resistance. The technique was originally established as an alternative to post-grouting to reliably account for the forfeited end bearing resistance. However, since it loads the shaft in a manner similar to conventional bi-directional tests, it can be used to not only load test sacrificial shafts, but production shafts as well. Furthermore, unlike conventional bi-directional load tests, the load is applied through surface jacks. These jacks, along with other load test components, are movable and can be reused to load test all the shafts of the project thus presenting an economic benefit. The concept of this technique has received favorable feedback from a few consulted departments of transportation, and while promising, has not been field tested to date. A U.S. patent was issued for the tip loading module and the loading technique described.

Sep 8, 2021

By Lawrence F. Johnsen, Marc J. Gallagher

"Micropiles are small diameter, bored, grouted-in-place piles incorporating steel casing and/or reinforcements. The omission of micropiles from most United States building codes has resulted in the application of varying standards for design and installation. The ADSC/DFI Micropile Committee has developed a proposed section for the 2006 edition of the International Building Code (IBC 2006) covering micropiles. The proposed IBC 2006 micropile code section is presented, along with comparisons to existing micropile codes and guidelines. A discussion section is provided to clarify sections of the proposed code. IntroductionMicropiles, defined as small diameter (typically less than 12 inches outer diameter), bored, grouted-in-place piles incorporating steel casing and/or reinforcements, are becoming common foundation elements for new construction, retrofits, and emergency repairs. Developed in Europe in the 1950's and used in United States practice since the late 1970's, micropiles are typically not addressed in building codes, particularly in the United States. As a result, micropiles are often reviewed by building officials to a variety of standards, including drilled shafts, caissons, cast-in-place bored piles, and concrete filled pipe piles. None of these adequately address the unique design and construction aspects of micropiles. Therefore, it became apparent to the foundation design and construction community that a micropile-specific code section was required.To that end, the International Association of Foundation Drilling and the Deep Foundations Institute (ADSC/DFI) Micropile Committee appointed a subcommittee in October 2003 to develop and submit a proposed micropile code section for the 2006 IBC. The subcommittee members included the two co-authors, as well as Tom Richards (Nicholson Construction Company), Tom Armour (DBM Contractors, Inc.), John Wolosick (Hayward Baker, Inc.), Allen Cadden (Schnabel Engineering) and Matt Niermann (Schnabel Foundation Company). At the time of the writing of this paper, the proposed code section has been presented at the IBC public hearing during which it was modified slightly. Final adoption (or rejection) will be determined by the IBC at the final action hearing in September 2005. The attached code section is the revised version following the public review hearings."

Jan 1, 2005

By Robert B. Bittner

The new gated dam on the Monongahela River at Braddock, Pennsylvania, was built for the US Army Corps of Engineers using an innovative "In-the-Wef' technology. A key feature of this technology involves construction of the foundations through the water and later mating the completed structure or a shell of the structure to the pre-installed foundation. This paper presents a description of the structure, its foundation, construction sequence and design details required to successfully Implement this technology.

May 11, 2007

By Armin W. Stuedlein, Jim Zammataro, Bernie Hertlein, Daniel Belardo, Qiang Li, Antonio Marinucci

"An experimental program focusing on four drilled shafts was conducted to determine the effect of high strength steel reinforcement bars on lateral resistance, steel casing on axial and lateral resistance, and steel casing without internal reinforcement on lateral resistance. Thermal Integrity Profiling (TIP) Thermal Wires and crosshole sonic logging (CSL) access tubes were installed in each shaft, and thereafter the corresponding non-destructive testing (NDT) was performed on each shaft to assess the integrity of the shafts and to compare the results from the different NDT methods. The results of the CSL tests using scored PVC tubes are compared against those conducted in 73/56 fully-threaded steel hollow bars, whereby the results indicated that the threaded bars served as a good host for performing the CSL tests. The data from the TIP Thermal Wires is compared against the results from the CSL tests for each of the four shafts, and the similarities and discrepancies between the two methods are discussed. This paper will serve as a reference to those interpreting the measurements and data obtained by performing nondestructive integrity tests on drilled foundations.INTRODUCTIONNon-destructive tests (NDTs) embody a set of critical tools for the evaluation of the integrity of constructed deep foundations, particularly for cast-in-place foundation elements. Construction defects may require the rejection of the foundation element by the owner’s representative, resulting in costly repairs or replacements and delays to the project schedule. The use and appropriate interpretation of the results from the NDTs provide the information required when evaluating the integrity of these constructed elements. A cooperative research program was conducted to assess the effects of various construction variables on the axial and lateral performance of drilled shaft foundations, which provided an opportunity to compare the established Crosshole Sonic Logging (CSL) test method to the newer Thermal Integrity Profiling (TIP) Thermal Wire method. This paper presents an overview of the experimental program performed at the geotechnical test site at Oregon State University (OSU), details of the CSL and TIP installation and testing methods, and the results of the NDTs on the constructed drilled shafts. Because one of the shafts was constructed with fully-threaded longitudinal steel hollow bars, this experimental program also allowed the assessment of the use of the hollow bars as access tubes for the CSL tests. Both the CSL and TIP test methods indicated that the shafts were of good quality and free from defects or anomalies; the data obtained using the TIP method also provided an estimate of the as-constructed shaft diameter and the reinforcement cage alignment, which will prove helpful when back-calculating axial and lateral load transfer during future loading tests."

Jan 1, 2016