Search Documents

By Shigenori Horikawa, Nobutaka Tanaka, Toshiro Hara, Kengo Yamamoto

"The CDM-LODIC method(Low Displacement and Control method), a modified the CDM(Cement Deep Mixing) method, reduces the ground displacement through the removal of in-situ soil equivalent to the amount of slurry injection using the continuous auger flight attached on the shaft above the conventional the CDM mixing tool. The reduction of ground displacement minimizes the impact on adjacent buildings and other infrastructures. Since the development of the CDM-LODIC in 1985, this method has been used for more than 900 projects with total volume of improved soils exceeding 5.3 million yd3 (7 million m3). The ground displacement that could be caused by deep soil mixing is controlled by balancing the volume of discharged soil and the volume of slurry injected for soil mixing. This paper presents the ground improvement work for the Sanriku Coast Expressway Project using the CDM-LODIC method to 1) control the ground displacement during ground improvement to minimize the impact to existing buildings and facilities and 2) utilize low height CDM-LODIC equipment to avoid potential damage to critical facilities in the vicinity of ground improvement area and avoid interference on the normal operation of the Ishinomaki Red Cross Hospital.INTRODUCTIONSanriku Coast Expressway is a reconstructed highway, which is part of an early restoration program to recover from the Eastern Japan Earthquake of March 11, 2011. This highway extends 223 mile (359 km) and connects the Pacific Coast regions of three prefecture of North Eastern Japan as shown in Figure 1. Along a section between Yamoto - Ishinomaki road, the highway was expanded from two lanes to four lanes to mitigate traffic congestion for the adjacent city center and hospital and to serve as an efficient transportation route for emergency or disaster relief needs as shown in Figure 2. Deep mixing ground improvement with an area replacement ratio of 50% was designed to provide settlement control under the new fill embankment of the expanded highway as shown in Figure 3. The original CDM treatment layout using 5.2ft (1.6 m) diameter columns is shown in Figure 4."

Jan 1, 2015

By Tom George

"INTRODUCTIONNo. 1 Queens Rd was an existing 10-storey office building founded on large pad footings. This project involved the construction of a 6-level, 15m (50-ft.) deep basement excavated immediately adjacent to the existing building and also beneath the existing footprint of the Southern end of the building. The total perimeter of the new basement was to be approximately 200m (656 ft.) all with a retained height of 15m (50 ft.). It was also proposed to add a further 5 storeys to the building. Approximately 18 of the existing columns supporting the 10-storey building were to have the applied column load diverted from the existing foundations at ground level onto the new piles or basement raft 15m (50 ft.) below.The geotechnical profile consisted of fill for the top 1.5m predominately comprising of clayey sand with a high gravel content from 1.5m to 9m (5 to 30 ft.), a medium dense to dense clayey sand and then below was a sandy clay extending to 15m (50 ft.) ranging from stiff to very stiff. From 15m on completely to extremely weathered siltstone was encountered. The groundwater was measured at 9.5m (31 ft.) below the natural ground surface.DESIGN BRIEFThe existing building columns were founded on large pad foundations up to 4.4m (14.5 ft.) square, founded on the dense clayey sand. These pads would require temporary support to enable the excavation to proceed beneath them. Upon completion of the excavation under the pads new columns were to be constructed joining into the existing columns to transfer the load onto the new raft slab, 15m (50 ft.) below. The existing 10 floors were to be refurbished. It was planned to undertake all the temporary support and transferring of loads while the structure above was only able to provide a dead load. It was decided that any movement of the building would have minimum impact on a skeleton structure. During the temporary support of the columns, movements due to construction activities had to be monitored to understand any potential stresses in the structure above.The original design required beams to be installed under the pads and supported at either end by temporary piles that were to be founded below the level of the proposed excavation. (Refer to sketch 1). Wagstaff Piling considered that this methodology had difficulties in construction at all stages and did not provide facility for transfer of the load without significant movement of the structure above. Wagstaff Piling revised the design to attach beams to the columns above the pads using shear collars. (Refer to sketch 2). These beams supported on the temporary piles could then be jacked upwards to remove loads off the pads. This would enable removal of the pads with minimal movement of the 10-storey building above. (Refer to photo 1 and back cover photo)."

Jan 1, 2005

By Jinung Do, Sung-Ryul Kim, Juhyung Lee

"Model tests have been performed to investigate the vertical, horizontal and cone tip resistances of bucket pile embedded in sand by different installation methods; suction force by pump and jacking force by actuator. Micro-cone penetrometer is used to evaluate the variation of the effective stress inside and outside of the pile after installation. As a result of vertical pull-out test, the jacked pile shows 3 times larger resistance than the suction-installed pile. For horizontal pull-out test, the ultimate horizontal capacity and the slope of load-displacement curve on the suction-installed pile decreases by 22% and 40%, respectively, compared to the jacked pile. In cone penetration test, inside cone tip resistance of the suction-installed pile is about 40% smaller than the jacked pile, which indicates that the effective stress is reduced due to upward seepage of bucket pile in sand by suction force. Therefore, installation methods can affect the behavior of the bucket pile significantly.INTRODUCTIONA suction force occurred when bucket pile penetrates into sandy soils induces seepage flow into the bucket pile so downward seepage near the outside of bucket pile causes to increases the effective stress, while upward seepage inside the bucket pile decreases the effective stress (Mahn, 2005; Fig. 1). The effect of induced seepage causes to reduce the penetration resistance during installation. On the other hand, reduced effective stress can decrease the horizontal and vertical capacities of bucket pile by significant disturbance at the tip of the bucket pile due to the flow net. Due to the complexity and difficulty considering the effects of suction installation, many previous researchers generally have neglected the effect of suction installation in their experiments. Therefore in this study, the effects of suction installation on resistance of bucket pile is examined."

Jan 1, 2016

By H. Mori

This paper describes a new borehole loading test using a self-boring instrument appropriate for dense sandy soils and stiff clayey soils. The results of loading tests for the bearing strata of deep foundations according to this method are also presented. This method has been applied to the study on the settlement behavior of heavy foundations resting on dense sand, stiff clay or soft rock in Japan.

Jan 1, 2010

By J. P. Powers

Methods for dewatering and the control of ground water for construction and mining are discussed, including open pumping; predrainage with deep wells, wellpoints or other systems; cutoff or exclusion of water by steel sheet piling, slurry concrete walls and slurry trenching, grouting, ground freezing, compressed air, slurry shields and earth pressure balance shields. Criteria are given for the selection among the methods for a given project. Unwanted side effects of dewatering are listed, with procedures for evaluating and avoiding them, by cutoff or artificial recharge.

Jan 1, 2010

By C. N. Baker

The design and construction of drilled piers through water bearing and caving soil conditions are discussed. The need for close cooperation between the design engineer and contractor in both the design and construction stage is outlined. Four case histories illustrating the design and construction considerations for four different problem soil and ground water profiles are presented, including the field testing and observation procedures that were utilized to confirm that the design inten. was accomplished. Requirements advisable when placing concrete under water in a cased environment and when placing concrete under slurry in an uncased environment are described.

Jan 1, 2010

By V. T. Ganpule

The effect of Sulphate and Chloride is well understood by the engineers. Most of the codes stipulate permissible limits for sulphate and chloride content in groundwater. Relatively few reference are available about the effect of organic acids on pile concrete. While executing a pile foundation work around Bombay, the authors came across the peculiar phenomenon. The routine testing of water has indicated that water is non-aggressive; however, on exposing the piles, the piles were found to be highly detonated. The testing of water on the guidelines followed by engineers associated with flow through pipes revealed that water is corrosive as per the Ryznar index concept. The present papers discussess the significance of Ryznar index in under water concreting.

Jan 1, 1996

By W. G. K. Fleming

The codification of foundation design and construction is a subject of extensive discussion in Europe and all current code proposals are based on limit state partial factoring. For simplicity, it is claimed, simplified forms of Partial Factor use are presently being advocated but, if this is the direction which codes are to follow, then it is preferable in this age of computer technology that a true system should be adopted rather than a simplification. A philosophically satisfactory method can readily be found which can fulfilcurrent requirements and it is better that such a method should be adopted from the beginning rather than later to find it necessary to make important alterations and amendments.

Jan 1, 1996

By Jorj O. Osterberg

This paper is for presentation at the 14th Annual Members Conference of the Deep Foundations Institute held at the Hyatt Regency Hotel, Baltimore Maryland on October 10, 1989. This is an introductory presentation of a one hour symposium on the applications of a new testing device. This paper discusses how the device works and its uses. Papers following this describe: - How the cell is constructed and calibrated - Two projects on which the device was used on long driven piles to determine the frictional capacity - A bridge project on which the device was used on an instrumented test drilled shaft and a working drilled shaft

Jan 1, 1989

By D. E. Sherwood

Twelve toe grouted, and eleven ungrouted piles, founded in very dense sands have been analysed to establish how toe grouting enhances pile performance. It is shown that pile stiffness is greatly increased, and that pile bases work effectively. This is in contrast to ungrouted piles, where some milli­meters of base movement may be required before the base is mobilised. Grouting appears to recover most of the disturbance caused during construc­tion, but in general does not enhance the ultimate bearing capacity of undisturbed ground.

Jan 1, 1989

By S. L. Karunakaran

There are cases where it is found that a raft foundation would have adequate factor of safety against ultimate bearing capacity failure but the settlements would be excessive. Piles may be introduced in order to limit settlements to an acceptable level. The actual number of piles required to reduce the settlements to an acceptable level may be very small compared to the number of piles required to transmit the whole structure load. The paper focuses on the difficulties encountered in evaluating the load sharing between raft and piles. An elaborate analysis taking into account the interaction between raft, piles and soil is very complex and time consuming. Few approximate methods for arriving at a satisfactory solution to piled raft system are discussed in the present paper.

Jan 1, 1996

By Z. Q. Bian

The wireline sampling originates from core drilling in rocks. The authors combined the wireline sampling technique with conventional undisturbed soil samplers, including Osterberg sampler, Denison sampler and double tube barrel, and then developed the wireline samplers of WPS, WSS and WSR models. These samplers are able to sample various soils. They reserve all the advantages of the original samplers, and moreover, they are noted with quick hoisting and lowering by wire rope. Therefore, it becomes an efficient new technique of sampling undisturbed soil from deep foundation.

Jan 1, 2010

By Shamsher Prakash

Estimation of vertical load carrying capacity of a single vertical pile under earthquake loading is an important task of a design engineer. Lateral vibration of vertical pile is highly influenced by the magnitude of vertical load. Several load reversal, during earthquake loading introduce gap between pile soil interface which reduces its load carrying capacity and increases lateral motion. This paper presents a simple time domain numerical scheme to estimate the lateral pile response, considering the loss of contact of pile at pile soil interface, during impact and earthquake loading. The motion of the pile is limited in the vertical plane. Time domain has been discretised into small intervals. The non linearity of soil properties has been taken into account by discretised Winklers model with Wolfes frequency independent mass spring dash pot coefficient for geometric damping. Suitable software has been developed which keeps track of the load reversal point of each elements.

Jan 1, 1996

By K. J. Yang

Based on investigations and model tests combined with pile foundation on Code compilation of drydocks, we present this report to give informations against uplift pressure of piles beneath floor of drydock. In a same kind of soil, we have got comparative tests results with single pile and pile group, and the latter was performed at different spacings, different embedded depths and different number of piles in the group. Having analyzed through the results, there are some new understandings of regularity about failure mechanism and uplifting capacity of single pile and pile group, as well as optimum embedded depth of pile foundation. The results of research approach to measured values of full-scale and model tests at home and abroad, it has been placed into the Design Code of Drydock in China (1985), and can give a reference to design of pile foundation at sea and on land under uplift loading.

Jan 1, 2010

By A. A. Gupte

Auger piling system which was developed in the United States in the 1940's is gaining acceptance in many parts of the world. Although primarily used to support foundations, the system is very useful for many other applications such as soil anchors, temporary and permanent earth retention systems, restricted headroom piling and underpinning of existing foundations. In this paper, review of current construction design techniques for the Auger piling system for earth retention and underpinning of structures is presented.

Jan 1, 1989

By H. S. Radhakrishna

Foundations supporting power transmission and communications towers are subjected to both compression and uplift loads, often of a cyclic nature. Some novel foundations, combining the beneficial features of grouted and helix anchors with that of compression piles and grillages, were developed by Ontario Hydro during the construction of high voltage transmission lines in Ontario, Canada. In addition to meeting the load requirements, the foundations permit easy installation in swampy areas and also minimize impact on environmentally sensitive terrain. This paper describes the features of these composite foundations and outlines the performance criteria used for their design and installation on the basis of load test results.

Jan 1, 2010

By John R. Davie

This paper describes the design and construction of two 5.6 MN capacity drilled piers installed to support the main loading elements of a large cantilevered gantry crane. The critical crane columns were located within and at the edge of an existing sheet-pile cofferdam, which had been filled with loose coal slag when it was originally constructed Due to the presence of the slag and the age and questionable condition of the sheet-piles, the drilled piers were installed to provide vertical and lateral supports for these columns. The lateral capacity of the piers was supplemented by two smaller drilled piers and two large spread footings that were linked by a system of grade beams.

Jan 1, 2006

By Shawn Downey

A helical pile with in-situ grouted shaft was used to underpin the existing slab of a large retail store in the Edmonton, Alberta Canada area. The existing structural slab did not have the capacity to support the increased load requirements. The design to upgrade the capacity specified a drilled shaft as the deep foundation to underpin a portion of the slab. A helical pile was quoted as an alternate and ultimately won the bid based on the advantages of the system. After an ASTM D1143 Quick Load Test confirmed the axial compression capacity, 723 helical piles with grouted shafts were installed in 3 weeks underpinning 40% of the 93,000 ft2 (8,660 m2) building.

Jan 1, 2003

Pier, well cap and steining junction is a complicated 3-d re-ion. The prevalent design procedure for the pier, well cap and steining in isolated manner is not rational. In absence of an integrated approach for design of the junction structure, the well cap is designed uneconomical and at the same time pier and steining are left relatively unsafe. Strut-and-Tie Model based design is a simple solution to this problem. An example illustrating design of the junction structure using STM is presented. On comparison of the outcomes of the STM based design with the prevalent design, the following anomalies are found: i) For smooth flow of forces, length of pier at its base should preferably be made equal to the outer well diameter, ii) STM based design for the pier is more rational, economical and safe. iii) Due to presence of hoop stress, as indicated by the STM, the steining concrete in a depth of p times outer diameter of the well from the well cap level should be limited to M15 grade, iv) STM based design for the steining is more rational, economical and safe.

Jan 1, 1996

By Terrence R. Udland, Russell D. Call

"Honored with a DFI 2006 Special Recognition Award, the Four Bears Bridge was constructed across Lake Sakakawea and opened to traffi c in September 2005. The very large lake size and severe winter conditions required an effi cient foundation design capable of resisting extreme ice loading and able to be effi ciently constructed in waters up to 90' deep (27.4m).DESIGNING FOR EFFICIENCYLocated in a remote area of North Dakota, the Four Bears Bridge replacement was a major undertaking for the North Dakota Department of Transportation, with dual goals of providing a new structure that would endure a severe environment, while enhancing the natural beauty of the area. Competing bids would achieve the best price for the owner, challenging the design team to creatively solve the engineering challenges unique to the site. Foundations for North Dakota’s new Four Bears Bridge had to accommodate water level fl uctuations of up to 40 feet (12m), along with extreme ice loading and be effi cient in order to be the low cost solution at the time of bidding. All three major criteria were achieved through the use of an effi cient ‘fl oating’ lost precast concrete cofferdam founded on steel pipe piles, which allowed the contractor to achieve the project schedule. The result is an award-winning bridge that is contextually sensitive to the environment. The bridge aesthetics pay tribute to the Three Affi liated Tribes, the Mandan, Arikara and Hidatsa, who reside on the Fort Berthold Indian Reservation, adjacent to the bridge site.The original Four Bears Bridge was located over the Missouri River near Elbowoods, the native grounds of the Three Affi liated Tribes. Construction of the Garrison Dam in the early 1950’s created Lake Sakakawea, a fl ood control project on the Missouri River, and resulted in the area being fl ooded. The bridge, along with many tribal members, was relocated to a site near New Town. The bridge provides the primary crossing of Lake Sakakawea and is a critically important transportation element for the residents of the Fort Berthold Indian Reservation. The relocated bridge had become functionally obsolete and not replacing it would require a detour of 170 miles (274km). The North Dakota Department of Transportation determined that it should be replaced. In order to achieve the most effective solution, the North Dakota Department of Transportation selected a design team responsible for the creation of competing steel and concrete designs that were competitively bid. The design team was led by Kadrmas Lee & Jackson, with FIGG responsible for the concrete bridge design, while Lichtenstein Consulting and Kadrmas Lee & Jackson completed the alternate steel bridge design."

Jan 1, 2007