Search Documents

By G. A. Davidson, P. G. Williams

"New developments in centrifugal slurry pump technology are discussed in relation to their importance for improving pump operation and reliability.Experimental data obtained by measuring the velocity of liquid flows in a slurry pump casing using Laser Doppler Velocimetry are presented. This demonstrates the importance of selecting pumps with the proper hydraulic design to provide optimum efficiency, maximum part life and minimum operating cost.The paper also discusses the use of new wear resistant materials, such as ceramic/metal composites, which can significantly improve the life of parts exposed to abrasive media. The results of laboratory attrition tests are presented. IntroductionCentrifugal slurry pumps are of primary importance for the hydro transport of abrasive and corrosive media in the mineral processing industry. As for all process equipment, slurry pumps must be carefully selected and operated to provide optimal performance. To achieve this, it is necessary to select equipment which will provide efficient and reliable operation for the specific service conditions and incorporates the best materials available to obtain maximum parts life.Abrasive wear of liquid end components is the most important aspect that distinguishes the design and application of slurry pumps from other types of pumps. It is therefore necessary to have a fundamental understanding of the mechanical interaction between pump components and the media being handled, as this will impact significantly on hydraulic design, mechanical reliability and selection of wear resistant materials. Recent advances in computational approaches'» have greatly improved the prediction of wear rates in pump casings by facilitating the solution of complex equations which describe the wear mechanisms mathematically. In conjunction with this, new experimental techniques allow researchers to measure flow fields in pump casings using non-invasive devices such as Laser Doppler velocimeters."

Jan 1, 1992

By M. J. Medd, G. A. Speirs

"This paper describes the simultaneous sinking and equipping of a 4.9 m diameter concrete-lined shaft to a projected depth of 1660 m. The shaft blast design utilizes the full face method using a parallel hole burn cut. Hydraulic drilling and a totally redesigned Cryderman-type mucking unit were integrated into the four deck sinking stage to provide for drilling, mucking, concreting and shaft steel equipping operations. A safety program was tailored and implemented specifically for this shaft sinking project.IntroductionIn July 1988, Falconbridge Limited commenced development of its Thayer Lindsley exploration site located some four km north of Sudbury on Regional Road 80.The first phase of this project was awarded to J .S. Redpath Mining Consultants Limited and the scope of work included the engineering and project management to construct a surface plant capable of supporting a shaft sinking and exploration program for potential future mine development. This initial phase of the project was completed on schedule and under budget on December 23, 1988, and is the subject of an independent paper.In November 1988, J.S. Redpath Limited was awarded the shaft sinking and exploration phase of this project. The scope of work consisted of sinking and equipping a 4.9 m diameter shaft to a depth of 1660 m and carrying out the development and diamond drilling on two levels. This work was scheduled to be completed by November 1991.The T .L. Exploration Project is located toward the eastern end of the south range of the Sudbury basin, north of Sudbury. Figure 1 details the projected mining area and the shaft location on the geological complex. Figure 2 is a section showing the exploration shaft that is located in the Norite. Two levels will be developed from this shaft, on the 1310m and 1588 m levels, to provide access for further geological examination of the ore bodies."

Jan 1, 1991

By B. J. Fryer, R. P. Taylor

"As a monitor of the processes involved in the formation of granitoid mineral deposits the coherent group behaviour of the rare earth elements (REE) actively reflects changing fluid characteristics. For example, in the porphyry environment, magmatic-hydrothermal fluids produce potassic alteration with strong enrichment in the light rare earth element s (LREE), reflecting their high pH, low fluid/rock ratios, and the dominant role of CI- complexing in metal (i.e. Cu, Au) transport. With increasing fluid/rock ratios and decreasing pH accompanying the progressive involvement of meteoric fluids (and the production of propylitic, argillic, and phyllic alteration) anionic species such as F - and CO, 2- become important in metal (e.g. Mo, W,) transport through complexing, and their activity in the hydro thermal fluids is illustrated by mobilization of the heavy rare earth elements (HREE).The relative involvement of CI- versus F - versus CO32- in metal transport in other granite-related systems can also be monitored through REE behaviour. Hence granitoid tin-tungsten mineralization and associated greisenization typically exhibit heavy rare earth enrichment and evidence the importance of F' and CO32- in metal transport. Similarly, heavy rare earth element enrichment in hydrothermal uranium deposits can be related to the transport of uranium as carbonate complexes. REE are widely accepted as powerful tools in the study of rock petrogenesis, but their use has been neglected in the investigation of mineral deposits. The recognition of the systematic variation of REE distributions in granitoid mineral deposits suggests that the application of REE geo chemistry, particularly when integrated with fluid inclusion and isotope studies, can provide (1) an effective method for identifying the physicochemical controls of metal transport and (2) a useful criterion for elucidating metal distribution."

Jan 1, 1983

By R. D. Studer

"The Snow Lake massive sulphide deposits are hosted by Aphebian volcanic rocks of the Flin Flon - Snow Lake greenstone belt, which in this area were deformed and metamorphosed to the amphibolite facies during the Hudsonian orogeny. All the known deposits occur in felsic rocks a short distance below the contact with an overlying mafic rock unit.The Stall Lake copper deposit occurs close to the top of an explosive felsic volcanic sequence. Rocks stratigraphically underlying the deposit have been hydrothermally altered by the mineralizing fluids. The sulphides were probably deposited from submarine volcanic vent(s) on the flanks of a felsic dome. The ore has been tightly folded, flattened and elongated parallel to the northerly trending lineation of the surrounding rocks during the several periods of deformation. Strike lengths of the lenses range from 60 to 300 feet and plunge-to-strike ratios are as much as 15:1.Ore lenses 1 to 4 typically consist of massive coarse-grained pyrrhotite, chalcopyrite and pyrite. A stratigraphically higher lens differs in that it contains fine-grained pyrite and chalcopyrite, with an increase in sphalerite toward its hanging wall. The No.4 orebody has a distinct footwall alteration zone characterized by brecciation and abundant chlorite-staurolite-garnet schist, with minor kyanite, anthophyllite, cordieriteand anhydrite, as well as sulphide minerals. Chemically, the alteration zone is distinguished from the unaltered felsic rocks by Na20 depletion and Mg-Fe enrichment.IntroductionThe Stall Lake copper deposit is located aproximately 4 miles southeast of Snow Lake in northern Manitoba (Fig. 1). The Snow Lake district has been a producer of gold (Rex, Bingo, Laguana and Nor-Acme Mines) and, since the fifties, of copper and zinc from deposits of Hudson Bay Mining & Smelting Co., Ltd . The district is located near the eastern limit of the Flin Flon - Snow Lake greenstone belt, which contains Amisk metavolcanic rocks of Aphebian age."

Jan 1, 1982

By G. E. Norman, R. E. Michelutti

"One of the major objectives of Falconbridge has been and continues to be, to minimize the impact of its operations on the environment around its Sudbury operations.The approach to achieving this objective and the results, are discussed under the following topics .I . Sulphur Dioxide Emission Improvements.2. Effluent Treatment Improvements .3. Effect of the Envrionmental Improvements.Sulphur Dioxide Emission ImprovementsHistoryThe rejection of pyrrhotite in the concentrators is one method of reducing the amount of sulphur to the smelter and therefore the sulphur dioxide emissions. In the 1950s and 1960s, Falconbridge developed the capability to remove 54% of this pyrrhotite. Numerous attempts were made to increase this amount by treating the pyrrhotite for recovery of nickel and in some cases elemental sulphur. Processes tested and operated were: hydrometallurgical pilot plant, roast-leach commercial operation and nickel-iron refinery. None of these processes proved to be commerically successful for both technical and economic reasons. Falconbridge therefore redirected its efforts to reducing sulphur emissions by improving its smelting process under The Smelter Environmental Improvement Project. A major component of this project was the installation of a sulphuric acid plant to recover the S02 in the roaster off-gases."

Jan 1, 1984

By P. Cielo

"Nondestructive inspection is an important quality control tool in the material processing industry. Being nondestructive, such a control may be applied to the whole production, as long as the available techniques are fast and easily automated. Ideally, nondestructive testing (NDT) methods should operate in a noncontact configuration in order to be deployable on-line with minimum perturbation of the production process.After a short introduction to the most common NDT techniques, with particular emphasis on ultrasonic, radiographic and electromagnetic methods, a few new approaches which are under development at the Industrial Materials Research Institute, (Boucherville, Quebec), are reviewed. Noncontact techniques such as laser ultrasound, thermoelastic and thermographic methodologies will be described, and their applications to materials of industrial interest will be discussed."

Jan 1, 1989

By J. W. M. Porritt, K. C. Cheng

Knowledge of radon emanation rates from uranium-bearing rocks is essential to the design of mine ventilation systems for uranium mines. Measurements of equilibrium ratio between radon and its daughters in mine air are important for a better control of mine radiation conditions. The concentrations of radon and daughters were monitored at cut-and-fill stopes in the Beaverlodge Mine of Eldorado Nuclear Ltd. during all phases of the mining cycle. The radon emanation rates of ore and rock samples were measured at the laboratory and the results were compared with in-situ emanation tests in an isolated ore drift. Samples of backfill solution, backfill drainage and ground seepage water were measured [or radon and analyzed for radium and uranium. The results showed that discharges of backfill solution and daily shift-end blasts were the two major sources for a rapid release of radon gas in the ventilation air. Other mining operations, such as drilling, mucking, etc., contributed little effect on radon release to the mining environment. Radon emanation rates of the Beaverlodge are samples ranged from 13 x 10-18 to 600 X 10-18 Ci/cm2/ sec and that of waste rock samples from 0.54 x 10-18 to 13.4 X 10-18 Ci/cm2/sec. The in-situ emanation rate of mine walls with ore-to-rock ratios of 1 to 7 was 60 x 10-18 Ci/cm2/sec. The average equilibrium ratio of radon and its daughters in stapes was 32.6%. Under a normal ventilation condition, the average background levels of radon concentration in cut-and-fill stopes ranged from 13 to 80 pCi/L. The discharges of backfill solution during backfill operations at 100 tons solids per hour released approximately 1.8 x 106 pCi/min of radon and elevated radon concentration in stapes 2 to 5 times above the background levels.

Jan 1, 1981

By Stuart McTavish

"The Brunswick Mining concentrator processes 10,000 D.S. T. per day of a complex sulphide ore. Four separate concentrates- zinc, lead, copper and bulk-are produced by selective flotation. Several major changes have been made to the Brunswick flotation circuit to improve the process and control. This paper will describe the present flotation practices at the Brunswick Concentrator. Special emphasis is given to the conversion of two of the primary circuits to an SO2-aeration flowsheet, and to the addition of a new secondary zinc flotation circuit that produces a zinc concentrate from the plant tailings. IntroductionBrunswick Mining and Smelting Corporation operates a zinclead- copper and silver mine and concentrator near Bathurst, New Brunswick. Since the start-up of operations in 1964, the flotation flowsheet has undergone major modifications to process the increased tonnages and to produce a greater number of concentrates. The flowsheet for the concentrator as it was in 1971 has been described by Neumann and Schnarru) and by Ersklneco. Since then, in 1971, the No.6 concentrator was converted from bulk flotation to selective flotation to produce a copper, lead and zinc concentrate. A separate zinc upgrading circuit was installed in 1972 and a bulk flotation or dezincing circuit, which reduced the zinc in the lead concentrate, was started in 1973. In 1976, the secondary zinc circuit was initiated.In addition to these new circuits, changes have been made to the existing circuits to simplify their operation."

Jan 1, 1980

By Nichols. R. S.

"Surface coal mining production from Elk Valley and area in southeastern British Columbia began in 1913. Since 1970, five open-pit mines have been put into production: Westar Mining&apos;s Hanner and Greenhills Operations; Fording Coal&apos;s Fording River Operation; Byron Creek Collieries&apos; Coal Mountain Mine and Crows Nest Resources&apos; Line Creek Operation.ln 1983 these mines produced 14.9 million tonnes of raw coal at an average strip ratio of 4.9 bank cubic metres of waste to 1.0 tonne of raw coal. This is 70% of the estimated 21.1 M tonnes annual capacity .Multiple seams are recovered with truck/shovel and dragline equipment. There is a wide range of equipment types in use with a recent trend toward larger and more mobile equipment.Coal mining in Elk Valley involves advancing along strike in four steps: hangingwall waste removal; seam cleaning; coal recovery; and foot wall waste removal. Each mine is unique in its approach to these four steps but the truck/shovel methods can be categorized into three main groups: seam dips < 35 degrees as at Harmer, Fording and Greenhills; seam dips 35 to 50 degrees as at Line Creek; and seam dips >50 degrees as at Byron Creek. Dragline mining at Fording involves bath waste and coal removal by draglines."

Jan 1, 1984

By R. A. Walker, G. Scheltgen, T. Javorsky, G. Blackwell

"Recent engineering advances in open pit rock mechanics have resulted in improved pit wall slope design and improved operating procedures in the event of a major wall instability. At the other end of the spectrum, on the scale of single bench failures, considerable discretion is left to the mine operators as to how potential problems are handled. The usual alternatives are either to operate with caution beneath potential hazards, or try to bring the unstable rock down. In specific cases it may be advantageous to attempt to stabilize rock structures for reasons of access and operating safety.A t the Brenda Mines open pit a prominent structure on the north wall had caused recurring bench-scale wedge failures when exposed on each mining level. In spite of operating precautions a shovel was hit by a rockfall causing significant damage. The first section of this paper describes the investigative, design, and stabilization methods which permitted subsequent mining beneath the structure to proceed without incident. Emphasis is placed on the personnel and equipment resources available at the mine site which were used to minimize costs and which would be available at most operating mines.The second section describes an ongoing research project that utilizes radio telemetry to transmit slope monitoring data. As part of this project the wedge structure was instrumented so that it could be continuously monitored with the aid of a computer. The application demonstrated the potential of &apos;micro- chip&apos; technology to remote data collection and processing as related to rock structure monitoring, slope stability and safety."

Jan 1, 1989

By C. A. Rowland

"Plant owners and operators, plant designers and grinding mill manufacturers are giving much attention to the design and manufacture of autogenous and semi-autogenous grinding mills, particularly the mills that have large diameters and draw power up to 10,000 hp and greater. Reliable designs giving long operating lives are required in today &apos;s ore processing plants.This paper reviews bench-scale and pilot-plant testing to determine first if the ore is suitable .to be ground by these methods and then reviews the data obtained from pilot-plant testing that is used to select the mills and the grinding circuit. The paper then discusses the use of the pilot-plant results to design the mills. The most important pilot-plant data used for mill design are power and the amount of ball charge to be used. The mill size selected is a combination of these factors. Pilot-plant data not only establish power requirements, but can be used in the selection of the type of drive, variable speed or fixed speed, and the operating procedure to be followed. This leads into the mill control circuit to be used. The total charge in the mill, the type of drive and mill discharge arrangements are needed in the calculation of stresses and bearing loads. Conclusions reached from pilot-plant work are used to obtain data for process design, and autogenous and semiautogenous mill design should be part of any test program incorporating either or both of these grinding methods."

Jan 1, 1981

By William E. Stanley

The paper examines the problems that arise in undertaking socio-economic impact studies to meet the requirements of environmental-impact legislation governing new mine development or expansion. An approach to undertaking socioeconomic impact studies is outlined, responses to specific problems are discussed and ways in which the mining company can use these studies to meet its general objectives are explored. The paper concludes by examining how a socio-economic study, as required by legislation, can be used to assist the mining company in achieving some general objectives it will have in developing a mine.

Jan 1, 1979

By M. Ghiani, P. Carbini, R. Ciccu, C. Del Fà

"This paper is concerned with the problems inherent in the efficient and economical processing of the fine fractions of a coal from the Sulcis basin (Sardinia, Italy) whose characteristics are typical of low-rank coals occurring in the Mediterranean region. Three different techniques, based upon surface properties, are examined. Flotation can be very efficient from both a technical and economic point of view, provided care is taken in the modulation of the flotation pulp. Interesting results have been obtained with oil agglomeration and this method could be economically feasible. Finally, electrical separation has proven a viable technique, although it entails preliminary drying.Besides discussing the problems encountered in the experimental research, some significant results of general validity are also given. They demonstrate that cleaned products can be obtained with fairly interesting recoveries, thus opening the way to advanced research aimed at setting up the most suitable technique for industrial application. IntroductionAs a result of the oil crisis, which caused a major upset in world energy supplies, the last ten years have seen a revolution in the energy policies adopted.In particular, the status of coal, which seemed destined to decline in view of the availability of liquid fuel, has had to be re-examined. The need to meet energy demands under improved reliability conditions and controlled prices through a broader and more flexible diversification of sources of supply has evoked, especially in highly industrialized countries, a renewed interest in coal. The result has been a consistent increase in demand and production as well as investments in new mines and the reinforcement of the infrastructure.This turn of events has also lead to a re-evaluation of young low-rank coals, hitherto considered uneconomical and thus neglected, because of their low heat value. In fact these coals, which have a high ash content, may also be relatively highly contaminated with sulphur. The above drawbacks, which still today preclude the widespread use of these coals, are bound to create even greater problems in the future as increasingly restrictive environmental control imposes, without exception, recourse to cleaner fuels."

Jan 1, 1986

By John De La Vergne, Morri Medd

"This paper describes the sinking of a circular concrete ventilation shaft through 110feet of water-bearing overburden. The brine circulation freezing method was used to stabilize the walls during excavation. In order to take advantage of the cold winter weather, a custom-built heat exchanger (natural radiator) was installed in place of the standard mechanical refrigeration plant.IntroductionIn the late fall of 1979, Les Mines Selbaie awarded a contract to the firm of 1.S. Redpath Limited to sink a ventilation shaft on its property in northwestern Quebec. The shaft was to be sunk through 110 feet of water-bearing overburden and approximately 90 feet of rock to a final depth of 200 feet below surface. The water table was measured at 16 feet below the surface elevation.After examining the soils report and diamond drill core from the shaft area, Redpath came to the conclusion that freezing was the best way to stabilize the overburden for sinking. LocationThe mine site is 420 statute miles due north of Toronto, just east of the Ontario/Quebec border (Fig. 1). Access to the site is provided by a development road built by the Quebec government from the Matagami/lames Bay Highway. History of Ground Freezing In the Mining IndustryIn 1862, shortly after the development of mechanical refrigeration, a mine shaft was sunk through an artificially frozen water-bearing formation in the United Kingdom. The first application of ground freezing in North America was for a Michigan iron ore shaft in 1888. Since that time, the freezing method has been used to sink hundreds of shafts throughout the world. Its best known application was to sink sixteen shafts through the Blairmore Formation in Saskatchewan.The same method has been used in every case. It involves chilling a calcium chloride brine solution and circulating the brine in concentric pipes, spaced between 3 and 6 feet around the shaft perimeter and usually 4 to 5 feet from the limits of the proposed shaft excavation."

Jan 1, 1982

By J. E. Nesset

"As an alternative to conventional dewatering by vacuum filtration and oil-fired rotary dryers, Brunswick Mining conducted extensive pilot-scale testwork on its copper, lead, zinc and bulk concentrates using a Larox Oy (Finland) automatic pressure filter. The results showed that pressure filtration readily produced final cake moistures of 6-8.5 per cent on this very fine sulphide material.An in-depth analysis examines pressure filtration in terms of metallurgical performance and projects energy savings of 78 per cent for pressure filters over the current dewatering operation. Potential energy and operating cost reductions are also estimated.IntroductionVacuum filters followed by oil-fired rotary dryers are one of the most common means of dewatering mineral concentrates. They represent, however, a level of technology which is exceedingly wasteful in terms of manpower, space utilization equipment and fossil fuel dependence. In addition, the use of thermal dryers is leading to increased environmental concerns both in plant and out.These were the primary factors which prompted Brunswick Mining to consider alternative dewatering methods as the existing equipment came up for replacement and upgrading. In late 1979, company engineers were encouraged by automatic Larox pressure filters seen at several Scandinavian operations. Subsequent laboratory tests by the manufacturer (Larox Oy of Finland) on several concentrate samples were sufficiently promising for Brunswick and Noranda to lease a trailer mounted filter-lab unit and a technician from Larox for a five-week period. Extensive on-site testwork on all four Brunswick concentrates (zinc, lead, copper and &apos;bulk&apos; lead-zinc) confirmed the potential of pressure filtration."

Jan 1, 1982

By Jean-Yve Tremblay, Michel Prud'homme

"Industrial minerals include a group of more than fifty minerals which are marketed into almost all the sectors of industry; they are the backbone of many manufacturing industries. Table I shows major end-uses for industrial minerals in manufacturing sectors. At Energy, Mines and Resources, industrial minerals are divided in three major categories: (I) agro chemicals and chemicals, (2) construction mineral s, and (3) ceramics and specialty minerals. A listing of the major groups of minerals is shown in Table 2. Agro-chemicals and chemicals are sold on the basis of their chemical content and purity. Construction minerals or structural minerals are distinguished by their performance as low cost and bulky commodities. Ceramics and specialty minerals are performance-specific and are sold for their property on imparting functions on end-products. Industrial minerals have unique characteristics that are useful in many stages of processing; from crushed size to micronized fillers a single mineral ca n serve a broad range of industries because of its intrinsic properties."

Jan 1, 1988

By Frédéric Flament, Mary Goldman, Gille Barbery

"Pilot plant testwork on autogenous and semi-autogenous grinding was conducted at the Centre des Recherches Minérales du Québec (CRM) to investigate the effect of ball addition, solids concentration in the feed, specific energy consumption and feed size distribution.A mathematical model that incorporates breakage and surface mechanisms of loss of mass was developed to predict load size distribution of autogenous and semi-autogeneous mills. An empirical model was used to predict product size distribution of autogenous and semi-autogeneous mills.IntroductionAutogenous (AG) and semi-autogenous (SAG) grinding circuits offer potential capital and operating cost savings when compared with conventional grinding. Empirical relationships have been developed to calculate specific power consumption for SAG mills using pilot plant test results (Mular et al., 1989; Barrett and Allan, 1986). Empirical models can be obtained from plant practice data but are applicable only to the particular ore and set of operating conditions used in the model. Grinding mechanisms have to be taken into account in order to develop a model that can be applied to different ores and mills.In AG and SAG, the ore itself acts as grinding media, with the finer sizes being crushed by the coarser ones. Surface mechanisms of loss of mass, in which the inner core of the particle remains intact, also take place. In SAG milling, the effect of balls also has to be taken into account. The role of each one of these mechanisms changes with particle size and the model has to account for such changes."

Jan 1, 1991

By E. M. De Souza

"A scientific testing program, sponsored by the Mining Industry Research Organization of Canada (MIROC), was undertaken on the surface and underground facilities of Inca&apos;s Crean Hill Mine to investigate the effectiveness of using dry drilling with a dust control system.The surface test work consisted of the monitoring of advance rates and bit life white a series of 165 mm holes, wet and dry, were drilled at both mine air (0.69MPa) and high pressure air (1.72MPa). The results, based on statistical evaluations of field data, indicated that penetration rates can be increased by an average of 24% when drilling dry with high air pressure and by approximately 27.5% when drilling dry with mine air as compared with wet drilling under the same conditions. Dry drilling also has the effect of reducing button wear by approximately 69% using high pressure air. The underground test work employed a dust collection system developed for use with large diameter holes (165 mm) and high pressure drilling. The testing program has indicated that an average increase in penetration rate of 35% can be achieved when dry drilling in rock (waste) and of 49% when dry drilling in ore with high air pressure. Although preliminary dust monitoring did not indicate any appreciable increase in dust concentration during dry drilling, further dust monitoring is still required.A comparative cost analysis has indicated the potential for reduction in drilling costs when dry drilling is utilized. Further testwork is to be conducted to develop a reliable dust collection system for underground production."

Jan 1, 1992

By Jean-Yve Tremblay, Michel Prud'homme

"IntroductionIndustrial minerals include a group of more than fifty minerals which are marketed into almost all the sectors of industry; they are the backbone of many manufacturing industries. Table I shows major end-uses for industrial minerals in manufacturing sectors.At Energy, Mines and Resources, industrial minerals are divided in three major categories: (I) agro chemicals and chemicals, (2) construction mineral s, and (3) ceramics and specialty minerals. A listing of the major groups of minerals is shown in Table 2.Agro-chemicals and chemicals are sold on the basis of their chemical content and purity. Construction minerals or structural minerals are distinguished by their performance as low cost and bulky commodities. Ceramics and specialty minerals are performance-specific and are sold for their property on imparting functions on end-products. Industrial minerals have unique characteristics that are useful in many stages of processing; from crushed size to micronized fillers a single mineral ca n serve a broad range of industries because of its intrinsic properties.The Industrial Minerals Industry in CanadaCanada has a large industrial minerals base and is a world leader in the production of some of them. The total value of product ion of these minerals has grown by 115% over the last 10 years despite the misfortune of asbestos.Industrial minerals have shown remarkable growth in the past 20 years at an average annual rate of 9.2%, compared to 7.8% for metallic minerals. In 1986, the value of industrial minerals rose to $4.9 billion, or 14% share of the Canadian mineral production. Figure I shows the value of production of the mineral industry for the period 1966-1986.The leading segment in industrial minerals segment since 1976 is the chemicals and agro-chemicals sector which has an average annual growth rate of 5.75 % in terms of value of production. During the same period, the growth rate for the whole Canadian mining industry was 1.37% per annum. The chemicals and agro-chemical s sector increased its contribution to the total value of production of 2% to 6070 despite the growing share of fuel minerals with 59%."

Jan 1, 1988

By E. Henderson

"This paper outlines the upgrading of a double-drum 2000 hp cage hoist to provide fully-automatic operation from shaft station control panels. The application utilizes programmable controller technology to provide all necessary functions for movement of personnel and material to 22 locations in a 4000 ft shaft.Various functions involving special design considerations such as ""chairing"", ""jogging"", and three modes of ""multi-level calling service"", are outlined. The use of higher level PLC functions to optimize memory utilization and simulate ""elevator service"" required the addition of a comprehensive fault finding software section to aid in troubleshooting.This paper will deal primarily with the automation portion of the project with references made to other pertinent aspects which were prerequisite to automatic operation. It is not intended to deal with every design detail, but rather to provide an overview of what can be done in the area of automation for those considering such an application. INTRODUCTIONEarly hoisting control systems provided only the essential elements of control, leaving many responsibilities with the operator. With advancements in various areas of technology, electromechanical devices were incorporated to enforce slow-down in end zones, control acceleration rates, monitor safety devices, etc. Brake control systems were supplied to allow for ""single-stick"" operator control, regulated deceleration during emergency brake applications, etc.These additions enhanced the over-all performance but were generally confined to speed and current regulation. Some mechanical devices, such as travelling nut limits, etc.; were used to provide ""position"" control to multiple locations within the shaft. These devices, in conjunction with rather extensive relay control panels, did allow for the establislunent of some automatic cage hoists . The hoists were often limited to service from point ""A"" to point ""B""&apos;, involving a limited number of levels due to the complexities of the mechanical interfaces employed. Only limited systematic work sequences were possible . .Programmable Logic Controllers (PLCs) were introduced into industry in the mid-70s and have since gained acceptance in mining applications such as pumping, ventilation, ore handling, etc. This technology, being ""software"" based, allows complexities to reside in the program rather than increasing the number of physical control elements. This has opened the door into hoisting systems for automatic loading and hoisting of ore as well as a means to achieve a comprehensive package of automated cage hoisting functions."

Jan 1, 1989