Search Documents

By W. H. De Blois

Introduction In the contact process for ?the manufacture of sulphuric acid, sulphur dioxide gas - produced by the burning of sulphur or of sulphur-bearing ores, or as a by-product in the treatment of sulphide ores - is made to combine with the oxygen of the air to form sulphur trioxide, which then only requires the addition of water to form sulphuric acid. The substance, as for example platinum, causing this combination is usually referred to as a catalyst, a convenient term, in the definition and explanation of which many pages have been written. Catalysis is now a comparatively common means of effecting chemical combination, but if the question were raised here tonight as to what actually goes on when this apparently innocent third party unites the parties of the first and second . part, without itself being altered in any way, I am afraid even our most learned members would have to confess their inability to entirely explain the phenomenon; for although the subject is under investigation, there is still much to learn. The contact process, however, is one of the outstanding achievements in chemical engineering. ? From the standpoint of the difficulties involved and the time absorbed in their solution, it probably stands alone in the field of technical chemistry. In fact, the manufacture of sulphuric acid has, from the earliest days, been surrounded with problems which have interested the ablest chemists. The Chamber System Although this paper has particularly to deal with the contact process, it may not be amiss to refer briefly to the chamber system, which was, and still is, a most important factor in the sulphuric acid industry.

Jan 1, 1927

By P. H. Rodriguez

The aquatic hazard classification system of the OECD and EU requires that sparingly soluble metal substances (SSMS) be tested using the OECD Dissolution/Transformation protocol in order to quantify the release of the ecotoxicological relevant species (dissolved ions). The SSMS category contains massive forms of metals, which due to their low solubility and slow transformation characteristics are a special case. The main factors that produce the release of metal into solution are exposed surface loading, pH, and stirring rate. The classification system at present prefers the use of mass loading as opposed to surface loading, in which case the amount of metal released will primarily be a function of the pH, and mass loading. Within the framework of the European Copper Voluntary Risk Assessment, coordinated by the European Copper Institute, we have proposed and developed a methodological procedure in which we demonstrate that surface area is an intrinsic property of a SSMS and we link the exposed surface loading to the toxicity reference value in order to obtain an aquatic hazard classification for massive metals. As example, the aquatic hazard classification for copper massive will be discussed. This approach is recommended for metal massives and metal powders.

Jan 1, 2007

By R. Tremblay, M. Burrows

"In the summer of 1990, pilot scale testing of a Jameson cell was carried out at Falcon bridge Limited, Kidd Creek Division. The Jameson cell is self aspirating and has fewer mechanical parts, thus it has a lower operating cost compared to conventional cells. This lower operating cost combined with positive pilot scale results, justified the evaluation of two full scale cells in the plant. The plant test had two mandates:1. Gain a thorough understanding of the cells operation and design constraints.2. Develop a flow sheet to replace three divisions of copper cleaner flotation.This paper provides an overview on the installation, commissioning and evaluation of the two Jameson cells acquired. The current status of the test program is also discussed.IntroductionThe Falcon bridge Limited-Kidd Creek Division concentrator is located in Timmins, Ontario. The concentrator, commissioned in 1966 and expanded in 1978, consists of four parallel grinding and flotation divisions utilising small cell (60 ft3) technology. With increasing pressure to maintain low operating unit costs a series of studies were undertaken to assess the impact of new technologies in the flotation circuits. The goals of the project were to improve productivity through increased metallurgical performance and/or reduced operating costs.One of the technologies investigated was the Jameson cell designed by Dr. Graeme Jameson of the University of Newcastle and marketed by MIM Holdings Limited, Australia. This style of column technology was chosen based on its potential for reduced capital and operating cost versus large conventional cells.The success of pilot testwork in 1990 led to the installation of two production sized Jameson cells beginning in October 1991. The units were to be used to confirm pilot results and determine equipment requirements for flotation modernisation. This paper will discuss the results and experiences Kidd Creek has had with the Jameson cell from pilot scale through installation and commissioning of the plant units."

Jan 1, 1993

By Hongpu Kang

The fully mechanized top coal caving mining method has been the main mining approach for thick coal seams with high output and efficiency in Chinese coal mines. The gateroads for the top coal caving mining faces should be driven along the floor of the thick coal seam with a part of the seam as roof. The support of the gateroads is commonly difficult because of the low strength and broken structures of the coal seams, and the increasingly large section of gateroads meeting the need of greater and greater face coal output. Based on the analyses on the geomechanics properties and production conditions of the top coal caving mining, the influences of the top coal caving mining parameters on the stability of gateroads, including mining thickness and face length, are studied. The deformation and damage features of the rock mass surrounding the gateroads with the top coal seam as roof are investigated, the interaction of the support with the surrounding rock mass, the support theory are studied. The bolting design method and criteria, bolting forms and parameters for the gateroads with the top coal as roof are put forward. The rock bolting components, including bolt bars, face plates, cable tendons, meshes, and steel straps, are introduced. Finally, the gateroad bolting effects are evaluated through a typical case study on the basis of field monitoring data, such as the displacement of surrounding rock mass and the forces along bolts and cables.

Aug 1, 2013

By D. Gorc, T. M. Fraser, Z. T. Nikic, R. Pesalj

"Mount Polley is an alkalic porphyry copper-gold deposit of Lower Jurassic age within the Quesnel terrane in south-central British Columbia. The silica-saturated Mount Polley intmsive complex is assumed to be coeval with volcanic rocks of similar composition in the Nicola Group in which it was emplaced. Other intmsions and some of the volcanic rocks in the Mount Polley area are silicaundersaturated and contain feldspathoids.The Mount Polley deposit is characterized by multiple intrusions that vary from diorite to crowded plagioclase porphyry to monzonite. Intmsion breccias are associated with some of the intmsive phases. Abundant hydrothermal breccias occur on the margins and above plagioclase porphyry intmsions. These breccias provide the main host for mineralization and are associated with the highest concentrations of copper and gold. The breccias are subdivided into four distinct types based on the dominant hydrothermal mineral in the matrix. Actinolite breccia is developed in an elongate zone within the core of the Central zone and grades laterally and vertically into biotite breccia to the southeast. Magnetite breccia is irregularly distributed and is relatively sparse throughout the deposit and albite breccia is dominant in the West zone. Pervasive and vein-related alteration correlates with the breccia types. The core of the hydrothermal system at Mount Polley is subdivided into three zones: actinolite, biotite and K-feldspar-albite. The margins of the core zone are overprinted by a discontinuous zone of calc-silicate minerals. This intermediate zone passes outward into propylitic alteration. Mineralization is most prominent within hydrothermal breccias and is generally present as disseminations, blebs within the matrix and abundant veins. Mineralization is associated with a chalcopyrite-magnetite-bornite assemblage in the core of the deposit passing out into magnetite-pyrite-chalcopyrite. Relatively constant copper to gold ratios suggest that both metals were precipitated under similar conditions.Hydrothermal breccias are genetically related to the emplacement of the crowded plagioclase porphyry melt. Crystallization of the melt was probably accompanied by volatile/aqueous exsolution, forming a water saturated carapace. Decompression of the chamber in response to magma withdrawal, fracture propagation and possible fault movement allowed hydrothermal brecciation to occur at the apex and margins of the intmsion. Alteration and mineralization appears to have been controlled by fluids migrating away from the plagioclase porphyry."

Jan 1, 1995

By V. Barranco, K. Yliniemi, A. Hubin, B. P. Wilson, D. Janas, M. Lundström, P. Hannula

Typical copper electrorefining electrolyte contains tens of grams of copper, some nickel and a wide variety of impurities. Some of these impurities comprise trace amounts of dissolved precious metals like Ag, Pd and Pt that currently are not fully exploited. This study presents an electrochemical method to recover precious metals via a combined electrodeposition-redox replacement (EDRR) process, where energy is used only to deposit copper during the ED-step, while the RR-step relies on the spontaneous replacement of copper by the precious metals (i.e. cementation). In order to conduct the recovery successfully, process parameters such as deposition potential (EDE), deposition time (tDE), redox replacement time (tRR) and the number of cycles (n) was adjusted. Investigations performed in synthetic electrolyte (40 g/L Cu, Ag = 10 ppm) proved the possibility to recover a high purity silver. Short deposition times (tDE) were found to result in small Cu particles that provided a suitably high surface area for silver cementation. In addition, experiments performed in real industrial electrolytes containing 44 g/L Cu and 54 ppb Ag (Boliden Harjavalta, Pori), demonstrated that EDRR could attain Ag recoveries of between 46–67% in an energy efficient, additive-free manner. INTRODUCTION The raw materials used in the state-of-art primary and secondary copper smelters contain mainly base metals, but also notable amounts of Ag, Pt and other precious metals. These valuable metals distribute mostly into the copper matte during the pyrometallurgical treatment (Tirronen et al., 2017) and end up into the cast anodes. During the electrorefining stage, metals more noble than copper such as gold and platinum, are not dissolved but enrich into the anode slimes. In contrast, silver may dissolve slightly and thus, minor chloride addition is used to retain silver in the slime as sparingly soluble AgCl. Moreover, other metals less noble than copper may also dissolve, such as nickel. Therefore the electrolytes used in electrorefining typically contain substantial amounts of copper, nickel and even arsenic as well as minor metals such as antimony and bismuth. In the Boliden electrorefinery these were reported to be in the magnitude of 51.2– 60.4 g/L of Cu, 10.9–15.8 g/L Ni, 7.2–15.9 As, 0.2–0.4 Sb and 0.1–0.4 Bi with an associated sulfuric acid concentration of 139–155 g/L (Lehtiniemi et al., 2018). Copper is the most noble of the dominating base metals in the electrolyte and is thus deposited on the cathode as 99.99% purity LME-A grade. Anode slimes are collected and subjected to precious metals treatment e.g. via pressure leaching—selenium recovery— Doré smelting—Ag refining—Au/Pt/Pd leaching and reduction process (Ludvigsson & Larsson, 2003). The Pori refinery, operating in Finland since 1941, not only produces 133 000 t Cu cathode and 2300 t nickel sulphate annually but also 66 t silver, 4.6 t gold and palladium and platinum (in year 2017).

Jan 1, 2019

By John Blackshaw

NEW sources of supply of tungsten concentrates became necessary when the flow from the Far East was blocked in 1942. In Canada, one source has been noted in the workings of the Hollinger mine at Timmins, Ontario. For many years, a small amount of scheelite had been removed with the gold ore, and an appreciable tonnage of scheelite still remained in the mine. At the request of the Dominion Government, a plant was built to recover this scheelite in the form of a concentrate that could be used by the alloy-steel industry without further preparation. The plant began operating early in March, 1942, and a small tonnage of ore, carrying scheelite and gold values, has been treated daily since then. The possibility of recovering the scheelite had been considered on several previous occasions. Each time the proposal had been given up because the total profits from the enterprise were estimated to be insufficient to repay the capital cost of building the recovery plant. At the time the plant was built, additional information had been gathered about the tonnage and grade of the scheelite ore in the mine, and several thousand tons of ore grading higher than 0. 25 per cent WO3 (tungstic trioxide) were known to be available.

Jan 1, 1943

By Reinis Sipols

AGENDA ? Introduction ? Definitions and Key features ? PEA - Preliminary Economic Assessments ? PFS ? Preliminary Fesibility Studies ? FS ? Feasibility Studies ? Costs and Risks ? Cash Flow, Economic Analysis and Reporting ? Recommendations for Improved FS accuracy INTRODUCTION ? The reporting of material information on mineral deposits has been governed by NI 43-101 legislation for almost a decade. ? The investment sector depends on the independent, professional QP to provide objective observations, comments and recommendations through all levels of geological, engineering and financial evaluation until a mine construction decision has been made.

May 1, 2013

By Richard Stewart

There are highly competitive world markets in most of the minerals being mined today. The high standard of living we enjoy in North America results in ever increasing productivity through mechanization and automation. Conventional underground and open-pit mining practices throughout the world are constantly changing to reflect the engineering advances of our technology. New records in tunneling, shaft sinking and excavating are being established. Larger and faster equipment is in production. Mining operations are being studied in detail to improve materials, methods and machines. Standards and controls are being established to measure the performance of people and equipment. These steps all tend to improve our present performance. In addition to these short-range improvements, however, there are the basic research and applied research studies which are aimed at developing entirely new approaches to our mining problems. Basic research in rock mechanics is coupled with applied research in rock penetration, fragmentation and stabilization.

Jan 1, 1963

"Pilot plants for pressure hydrometallurgy represent special design and project execution challenges. Over the past twenty years, Zeton has designed and fabricated a variety of world-class pressure hydrometallurgical pilot-plant facilities, and this paper discusses design considerations and strategies related to such projects. Project execution methods are also discussed, and guidance is given for the selection of materials of construction and for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical pilot equipment. The paper concludes with a discussion of the need for process similarity with future commercial operations and the realities of pilot-scale equipment.INTRODUCTIONThe process technology developer or owner and the designer/fabricator of a new pilot-plant facility are faced with some difficult technical choices even after the decision to build a dedicated plant has been taken. A pilot-plant project is usually on the critical path of a large commercial project involving investments many multiples greater than the capital cost of the pilot plant. Schedule savings in the design, manufacture, and commissioning of the pilot plant or in a rapid completion of the experimental program can be disproportionately beneficial to the overall development project. However, inappropriate shortcuts resulting in major oversights can be disproportionately problematic.A number of considerations and suggestions for both the project execution approach and the process engineering design of pressure hydrometallurgical pilot-plant facilities are presented as a guide for potential owners and operators of new pilot-plant equipment and facilities."

Jan 1, 2012

By F. Ford, Z. Dai, A. W. Lee

ABSTRACT: As high-grade nickel sulphide ores are being depleted and processing laterite ores continues to pose challenges, the future of nickel extraction lies in low-grade ultramafic ores. Canada has large resources of low-grade ultramafic nickel sulphide ores in the Thompson Nickel Belt. Most of the deposits are high tonnage and open pittable, but have high MgO content. The main challenge in processing low-grade ultramafic ores is the presence of serpentine. Chrysotile, one of the three polymorphs of serpentine, is the most common form of asbestos. In addition, the high slurry viscosity associated with ultramafic ores makes grinding and flotation possible only at a very low solids percentage.

Jan 1, 2011

By R. Holmestad, M. Gazizov, S. Wenner, R. Kaibyshev, J. K. Sunde

"Mechanical properties and microstructure of an Al-4.7Cu-0.74Mg-0.51Si-0.48Mn-0.10Cr-0.09Ti-0.02Fe (wt. %) alloy subjected to various thermomechanical processing (TMP) have been investigated and compared to conventional ageing at 170°C (designated T6). Three TMP routes involving cold deformation of solution treated samples were tested. These were (i) 3%-stretching (T8-3%), (ii) equal-channel angular pressing (ECAP) to true strain (e) of ~1 (T8-1) and (iii) ECAP to e~2 (T8-2), all with subsequent ageing at 170°C for 0-96 h. At peak age conditions, both yield stress, ultimate tensile strength and elongation-to-fracture decreased for the T8-3% state as compared to the T6 condition. Intermediate ECAP (T8-1 and T8-2) lead to significant increase in maximum yield stress, ultimate tensile strength and elongation-to-fracture. The changes in mechanical properties were related to microstructure evolution, encompassing changes in grain sizes, dislocation densities, precipitate morphology and phase fractions, which were characterised using transmission electron microscopy. Relations between TMP, precipitation behavior and contributions to different strengthening mechanisms are evaluated.INTRODUCTION Al-Cu-Mg-Si alloys are widely used as structural materials in aerospace industry due to their attractive combination of high specific strength, good fracture toughness and enhanced creep resistance. These properties are largely due to the formation of a large number of nano-sized metastable precipitates during artificial ageing (Polmear, 2006; Eskin, 2003; Gazizov, Dubina, Zhemchuzhnikova, & Kaibyshev, 2015). The precipitation behaviour in these alloys is complicated and depends among other things on Cu concentration and the Mg:Si ratio (Wolverton, 2001; Chakrabarti, & Laughlin, 2004). In general, the precipitation sequence has been presented in a prior study (Eskin, 2003) as follows:"

Jan 1, 2018

By A. Hekmat-Ardakan

Conventional hypereutectic Al-Si alloys such as A390 are used principally for the casting of components used in wear applications requiring abrasive resistance such as in engine or compressor blocks. A comprehensive study was undertaken to investigate the potential of improving the mechanical properties of these alloys by the addition of magnesium. A thorough thermodynamic study of the effect of the addition of Mg to the conventional A390 alloy showed that Mg2Si starts to form as a primary phase at 4.2% Mg as well as in the products of the binary and ternary eutectic reactions forming the matrix. Experiments were carried out in producing castings with different cooling and solidification rates of alloys with up to 10% Mg. Mg additions were found to increase the hardness over the as cast alloy due to solid solution strengthening. Also, T6 heat treatment greatly improved the tensile properties of these alloy compositions due to the strengthening effect of the theta-Al2Cu phase. The elongation of these alloys generally decreases marginally with Mg content. The most significant property improvement of the alloys with higher Mg content is the substantial increase in wear resistance. This is attributed to the dispersion of smaller particles of Mg2Si and their coherence with the matrix as compared to the large Si particles in the conventional alloy. A new rheoforming process for A390 is presented that improves the processing of the semi-solid slurry. Structure modification elements were also added to refine the primary and eutectic silicon greatly improving the processing of the semi-solid slurry.

Jan 1, 2011

By Michael Cullen

The Quinsam Coal Mine is in the process of extracting a panel beneath the mine access road. To prevent damage to the road, and adjacent powerline, it was necessary to establish a ?protection zone? within which the extent of mining would be limited. The protection zone is analogous to the setback limit. For economic reasons it was desirable to make the protective zone as small as possible, and with the greatest extraction ratio possible. The size of the protective zone was established by determining the angle of critical deformation using the numerical model FLAC, coupled with field data on subsidence from the Mine. The angle of critical deformation (defined as the angle, measured from the vertical, at which intolerable damage is sustained by a structure) was determined to be between 0 and 5 degrees. The allowable extraction ratio in the protection zone was established using the ARMPS method of pillar design coupled with field data on pillar stability from the Mine. Excavations spans to prevent caving were determined by historical experience and field data on span stability from the Mine, coupled with numerical modeling. The minimum pillar size was determined to be 7.5m. The maximum pillar height was established at 2.5m. The maximum allowable excavation span was determined to be 8.5m. With these criteria, extraction ratios between 54 and 73% (measured in plan view) were determined to be appropriate for the protection zone.

May 1, 2001

By Rick J. Chalaturnyk

In Alberta, oil sands bitumen is utilized for synthetic crude oil production by surface mining, bitumen extraction followed by primary (coking) and secondary (catalytic hydrotreating) upgrading processes, or by catalytic hydrocracking and hydrotreating replacing the primary and secondary upgrading processes. Oil sands tailings, composed of water, sands, silt, clay and residual bitumen, is produced as a byproduct of the bitumen extraction process. Several processes have been proposed for the treatment of oil sands tailings, resulting in different recovered water characteristics, consolidation rates and consolidated solid characteristics, which may have effects on the performance of the overall plant operations. A process for the same purpose has been developed by treating the oil sands tailings with CaO lime and CO2 and thickening it using a suitable thickener. In this process a release water of acceptable properties is recovered in a short retention time, which makes it possible to recycle the recovered water, probably after a reconditioning treatment, as warm as possible to improve the thermal efficiency of the extraction process. The paper presents the theory and laboratory results for the CaO and CO2 thickening of low temperature flotation tailings. The water release rates, segregation potential of the thickened underflow and chemistry of the release water are shown and discussed. It is suggested that in using the proposed process, the thickened tailings underflow can be disposed for further consolidation, or combined with the coarse tailings to produce Blended Composite Tailings, corresponding to the Composite Tailings process in the existing hot water extraction plants.

May 1, 2002

By M. D. Johnson, R. K. Bezys

"The majority of Ontario's limestone and dolostone production comes from a few Paleozoic carbonate units. In eastern and central Ontario, Ordovician rock units, which are the main sources for production, include the Oxford, Gull River, Bobcaygeon, Verulam, and Lindsay Formations. They are predominantly utilized for aggregate and cement manufacturing, with the Bobcaygeon Formation being used as a source of building stone. Along the Niagara Escarpment, the Silurian Lockport, Amabel, and Guelph Formations are sources for the limestone industry. The largest tonnage of rock extracted by the industry comes from these Silurian units, especially the Lockport and Amabel Formations. These units are used primarily for aggregate, although they are also a source for lime. In southwestern Ontario, the Silurian Bertie Formation and Devonian strata, represented by the Bois Blanc Formation, Onondaga Formation, Detroit River Group, and Dundee Formation, contribute to Ontario's production of lime, cement production and crushed stone. The Detroit River Group (Lucas and Amherstburg Formations) is the main source of the lime and cement produced in the province.Northern areas, which may become significant sources for the industry, include Manitoulin Island, the Lake Timiskaming area, and the James Bay Lowland. IntroductionThe Engineering and Terrain Geology Section of the Ontario Geological Survey has undertaken a geological inventory of all active and abandoned limestone and dolostone quarries in Ontario. This geological study, combined with a commercial study of active quarries carried out by the consulting firm of Derry, Michener, Booth and Wahl, will provide an up-to-date report on the industry in the province and will be published by the Aggregate Resources Section of the Ministry of Natural Resources. This report will follow the format and style of D.F. Hewitt's Ontario Department of Mines Industrial Mineral Reports and Circulars (Hewitt, 1960, I964a, 1964b, 1964c; Hewitt and Vos, 1972). Examinations of the quarries were carried out by geologists in the Paleozoic I Mesozoic Geology Subsection of the Engineering and Terrain Geology Section, and include, in addition to the authors, R,R. Wolf, V.A . Mazur, and D.K. Armstrong in the summer of 1986."

Jan 1, 1988

By M. D. Johnson, R. K. Bezys

"The majority of Ontario's limestone and dolostone production comes from a few Paleozoic carbonate units. In eastern and central Ontario, Ordovician rock units, which are the main sources for production, include the Oxford, Gull River, Bobcaygeon, Verulam, and Lindsay Formations. They are predominantly utilized for aggregate and cement manufacturing, with the Bobcaygeon Formation being used as a source of building stone. Along the Niagara Escarpment, the Silurian Lockport, A mabel, and Guelph Formations are sources for the limestone industry. The largest tonnage of rock extracted by the industry comes f rom these Silurian units, especially the Lockport and Amabel Formations. These units are used primarily for aggregate, although they are also a source for lime. In southwestern Ontario, the Silurian Bertie Formation and Devonian strata, represented by the Bois Blanc Formation, Onondaga Formation, Detroit River Group, and Dundee Formation, contribute to Ontario's production of lime, cement production and crushed stone. The Detroit River Group (Lucas and Amherstburg Formations) is the main source of the lime and cement produced in the province.Northern areas, which may become significant sources for the industry, include Manitoulin Island, the Lake Timiskaming area, and the James Bay Lowland. IntroductionThe Engineering and Terrain Geology Section of the Ontario Geological Survey has undertaken a geological inventory of all active and abandoned limestone and dolostone quarries in Ontario. This geological study, combined with a commercial study of active quarries carried out by the consulting firm of Derry, Michener, Booth and Wahl, will provide an up-to-date report on the industry in the province and will be published by the Aggregate Resources Section of the Ministry of Natural Resources. This report will follow the format and style of D.F. Hewitt's Ontario Department of Mines Industrial Mineral Reports and Circulars (Hewitt, 1960, I964a, 1964b, 1964c; Hewitt and Vos, 1972). Examinations of the quarries were carried out by geologists in the Paleozoic I Mesozoic Geology Subsection of the Engineering and Terrain Geology Section, and include, in addition to the authors, R,R. Wolf, V.A . Mazur, and D.K. Armstrong in the summer of 1986."

Jan 1, 1988

By J. A. Allan

"The history of the development and application of controlled recirculation systems in U.K. collieries is traced and the theory behind such systems briefly examined. Specific applications for dealing with dust and dust/heat problems in headings, for which practical experience is currently available, are described. Consideration is given to the special features which these systems introduce in the underground situation and to the essential safeguards which are required for their safe use.IntroductionRecirculation of air is a commonly used technique in genera l ventilation and air conditioning practice, but has always been regarded with some suspicion for mining applications. This is perfectly understandable in view o f the hazardous conditions which can occur with dangerous forms of recirculation in mines. However, certain controlled recirculation techniques can offer advantages, particularly in the field s of dust and climate control in headings, provided that they are designed, Installed an d managed with full comprehension o f all aspects of the system and always bearing in mind that from the point of view of serious firedamp ignition risk, headings are potentially the most hazardous places in coal mines.BackgroundProbably the first recorded use of deliberate recirculation in British collieries was reported by Lawton in 1933. This researcher described trials, undertaken under the auspices of a national committee on ""The Control of Atmospheric Conditions in Hot and Deep Mines"", involving attempts to increase the velocity, and thereby the cooling power on hot faces, by means of simple recirculation systems using fans and ducts delivering recirculated air in the opposite direction to the normal face airflow. No significant cooling advantage was obtained and there is no subsequent record of this work being continued. During the discussion on this paper, there was considerable disbelief that fire damp percentages had not increased significantly when air was recirculated, but apparently no attempt was made to establish why this should be. It is of interest to note that J. Ivon Graham, one of the contributors, recommended that recirculation should be tried in stone headings for the control o f dust, as he believed that ""there may be scope for recirculation and filtration of the air under certain circumstances in such headings"". This idea was not developed for another forty years."

Jan 1, 1983

By M. Kuyumcu

With annual production of almost 3.5 million metric tonnes of K20, former East Germany (GDR) was the world?s third-largest producer of potash, ranking behind only the Soviet Union and Canada. More than 80 % of production was intended for export to earn urgently needed hard currency. For this reason, beginning in the 1970s, East Germany began to mine unprofitable hard-salt sources and carnallitite fields, which are geomechanically problematic. In the course of restructuring from a centrally planned to a market economy after German reunification, only two of the nine existing potash mines were classified as economically viable for privatization. All six potash mines in the South Harz Region were closed between 1991 and 1993. The orderly safekeeping of these potash and other decommissioned ore mines and the rededication of mining areas were assigned in 1992 to a German state-owned company GVV founded especially for this purpose. Elaboration in the present documentation covers the local necessity of the type and extent of filling and safeguarding measures. As a result of the remedial measures taken, it was possible to prevent the collapse of cavities and damage to surface facilities. This documentation describes the safeguarding successes to date, with appreciable reduction and stabilization of surface settlement and with significant lessening of seismic events. Also presented are concepts updated to the state of the art for safeguarding of numerous potash mining shafts for long-term effectiveness in separation of the workings and watercourse levels in the cap rock. In the course of 100 years of production, six mining dumps resulted with a total volume of approximately 170 million m3. They consist of up to 95 % of water-soluble salts. Every year, precipitation dissolves up to 500,000 tonnes of this salt, which enters as a highly concentrated solution into watercourses and ground water. Explanation follows of measures for minimization of environmental pollution by covering of dumps and controlled drainage of alkaline solutions from the dumps. Finally, presentation is made of the results of the successful work until now by GVV for reuse of decommissioned mining sites with settlement of new companies for creation of additional jobs and for revitalization of the monostructured South Harz Potash Mining Region.

Aug 1, 2013

By Youngjib Ham

Understanding energy performance of existing buildings is vital to increasing their efficiency and reducing the overall energy consumptions. This entails facility managers to systematically monitor building energy performance and reliably identify and analyze potential problems. Currently, infrared thermography is widely used as a primary diagnostic tool for the detection of building performance problems. Nonetheless, applications of thermal images for building inspection are mainly restricted to manual and labor-intensive identification and qualitative assessment of heating or cooling loss. Automated identification of potential problems and reliable cost analysis of the associated energy loss can help homeowners to minimize financial risk of retrofits and maximize energy savings. To that end, this paper presents a new automated method for calculating the cost of energy loss for building diagnostics. In the proposed method, first, using a hand-held thermal camera, the auditors collect digital and thermal imagery from the buildings under inspection. Then, using a recently proposed method for Energy Performance Augmented Reality (EPAR) modeling, an actual 3D spatio-thermal model is generated and superimposed with a computational fluid dynamics (CFD)-based expected energy performance model. The resulting EPAR model is placed into the method proposed in this paper for cost analysis of the energy loss. Through a new 3D thermal mesh modeling using k-d tree structure and nearest neighborhood searching, performance deviations between these models are automatically calculated. Using a temperature threshold, the areas associated with potential performance problems are detected in the EPAR model and are visualized using a metaphor based on traffic light colors. Then, the actual R-values of the detected areas are measured at the level of 3D points. Based on the measured R-values and the estimated air change rate for the detected air leaks, (1) the heat loss or gain caused either by poor insulation or air infiltration/exfiltration and (2) the associated energy costs are automatically calculated. The proposed method is validated on several locations of existing residential buildings. The preliminary results show the potential of the proposed method for minimizing the inspection time as well as the risk associated with the cost analysis of retrofitting potential building performance problems.

Aug 1, 2013