Search Documents

By J. D. R. Neilsen

The objective of the research conducted and presented herein was to determine the effect of pre-established free gas saturation on the sweep efficiency of an isolated inverted five-spot well pattern. The investigation concluded that the ultimate recovery of an isolated inverted five-spot may be slightly increased by establishing a free gas saturation prior to water flooding; however, of more significance is the extreme deviation of the pattern's performance after water break-through from that commonly obtained from developed well patterns. The rapid "water-out" characteristic common to both linear floods and floods conducted in developed well patterns was not evidenced in the isolated inverted five-spot. Instead, the wells continued to produce oil long after breakthrough until ultimate areal sweep efficiencies of four, five, and six hundred percent were obtained prior to the water-oil ratio becoming excessive.

Jan 1, 1962

By Harry Wilton-Clark

Introduction Coal cleaning may be taken as meaning the separation of coal-as-mined into two or more fractions. Coal cleaning includes coal washing, together with any other means used in the ultimate preparation of coal prior to shipment (as coal) . The method of coal cleaning devised for any given mine must be one which is based entirely on the economic results obtainable. The installation of a high-cost and complex washing plant, designed to produce a low-ash dean coal, at the highest possible recovery, may be unsound practice. A crude 'roughing' washer may be the best result of sound engineering and operating consideration, and in some cases coal cleaning should be confined entirely to preparation at the face. Consideration of complete costs, to the point where the coal is actually sold, may show that certain seams are workable or not workable. Of the seams found workable, extraction of the whole or parts of the seam may be decided on. The portion to be extracted may contain rock or bone partings, which must be removed. It may be good practice to mine the extra portion and remove the objectionable materials by surface washing; or it may be that such materials should be removed underground, even at an increased mining cost. For instance, in some of the steeply pitching seams of the Alberta Crow's Nest Pass district, the removal of bone and rock at the face may be almost impossible under the usual 'up the pitch' or 'angle' mining methods, but possible by mining across the pitch so that the material to be rejected can be removed and gobbed. Again, if a complete seam is being extracted, investigation may show marked differences between top coal and bench coal, and if sufficient mine cars are being loaded from a chute at one time, the fact that such a place is working top or bench coal at the time may be reflected by peaks in ash content or size proportions at the ripple. It may be very effective coal preparation to smooth out such peaks.

Jan 1, 1934

By L. S. Beck

"IntroductionThe Beaverlodge District is an important mineralogenic province of pitchblende and occupies about 1300 square kilometres centred on Beaverlodge Lake near the north shore of Lake Athabasca in northwest Saskatchewan (Fig. 1). Uranium City is the main settlement of the area and is serviced by scheduled aircraft from Edmonton, some 700 km to the southwest, and from Prince Albert which lies a similar distance to the south.During the summer, boats and barges supply the area from the railhead to Fort McMurray via the Athabasca River and Lake Athabasca, a distance of about 550 km. For the past few years a winter road has been maintained across Lake Athabasca to Cluff Lake to connect with Highway 155.The topography of the area is typical of the Precambrian Shield with generally low relief and a disorganized drainage of numerous lakes separated by hummocky rock ridges, muskeg and drift-covered areas. Local topography in the area is, however, extremely rugged, particularly south and east of Beaverlodge Lake, where resistant rocks form prominent hills and ridges extending as much as 180 m above lake level. Rock exposures are abundant and form over 50 per cent of the land area.History of Exploration and DevelopmentEconomic interest was first aroused by Tyrrell (1896) who described an occurrence of iron formation at Fish Hook Bay; however, subsequent evaluation of the deposit indicated it to be uneconomic."

Jan 1, 1986

By M. Reda

Because of the adverse environmental effect of Chromate, Molybdate ions had been investigated as replacement for Chromate and the results had shown not to be encouraging. Film deposited from peroxopolymolybdate (from reaction of Molybdenum meta, with excess Hydrogen Peroxide), are more robust than that deposited from molybdate solutions. This was shown to be due to higher fraction of Mo (IV) and Mo (V) that form from Mo (VI) in the peroxopolymolybdate deposited film than the film deposited from Molybdate solutions. The peroxopolymolybdate film contains 40% un-hydrated molybdic acid, tetraperoxodimolybdate and tetra peroxo tetra molybdate. The protective properties of peroxopolymolybdate were shown to be due to the effectiveness of the un-hydrated molybdic acid.

Jan 1, 2010

By P. Rosario

"Current industry practice for HPGR assessment and sizing relies on conducting a series of tests using pilot-scale machines with roll diameters of 700 mm to 1000 mm. Substantial amounts of sample are required for such pilot test programs, typically 1 to 10 tonnes of the sample is needed depending on the level of study and complexity of the resource. Collection of large quantities of representative samples during the early stage development is challenging and expensive, thus significantly hinders the HPGR technology from being incorporated into early-stage designs. A robust and reliable laboratory test is therefore needed to allow a fair consideration of HPGR for early stage projects. With support from the Canadian Mineral Industry Research Organization (CAMIRO), the NBK Institute of Mining Engineering at the University of British Columbia (UBC) developed a suite of Piston Press bench-scale tests that correlated to pilot and full scale HPGR operating information (Davaanyam, 2015; Davaanyam et al, 2015; McClintock, 2018). The Piston Press Tests (PPTs) are capable of assessing the HPGR technology at the scoping, pre-economic analysis (PEA), and pre-feasibility (PFS) stages of project development. This paper will briefly describe the theory on which the PPTs are based, and then presents a case study conducted for a copper deposit to show how the PPTs are being used for scoping and pre-feasibility level studies. Specifically, the PPTs are being used to provide information for preliminary sizing and selection of an HPGR and to assess the effect of ore variability on HPGR performance. The results are also applied to developing HPGR circuit designs and can be incorporated in simulation so that optimum design parameters can be selected.INTRODUCTION It is widely accepted that high pressure grinding rolls (HPGRs) offer a viable energy-efficient solution for the modern comminution flowsheet design. Table 1 summarizes selected examples of HPGR applications in the hard rock mining industry. The main benefits of HPGRs are energy savings which leads to lower operating costs, and its stable operating characteristics that can better cope with variations in ore hardness when compared to the conventional SAG mill-based comminution circuits."

Jan 1, 2019

By J. R. Fisher

"Uranium may be leached to some extent in situ from the Blind River conglomerate uranium ores by using the products of bacterial activity from the bacterium Thio-bacillus ferrooxidans his paper describes some of the laboratory techniques used to investigate the characteristics of the bacteria, and to utilize their properties in uranium leaching. The application of some of the laboratory results underground at the Milliken mine of Rio Algom Mines Limited are de-scribed, along with the method of uranium recovery from the mine waters."

Jan 1, 1966

By F. Mohamm

"Recent changes in regulations and scientific advances concerning selenium bioaccumulation have placed greater importance on non-biological treatment systems for selenium control. Mining wastewater contains hexavalent selenium (selenate) as the predominant aqueous species and possibly small amounts of tetravalent selenium (selenite). Non-biological removal of selenite is accomplished readily and cost effectively by ferric co-precipitation and adsorption using ferric oxyhydroxides sourced from ferric salts or iron anodes in electrocoagulation cells. Selenate on the other hand is difficult to remove. It is often incorrectly assumed that electrocoagulation is suitable for removing both selenite and selenate. Selenate removal efficiency by electrocoagulation is low and the amount of waste residue produced high. In contrast, BioteQ’s Selen-IX™ process removes selenate very efficiently and produces a much smaller amount of stable residue. The process combines selective ion exchange with electro-reduction of selenate in electrocells that physically resemble electrocoagulation cells but are designed and operated differently. This paper summarizes four years of pilot scale demonstration on a wide range of mine waters and discusses the key benefits and limitations of Selen-IX™. The pros and cons of combining ion exchange with electro-reduction in comparison to direct electro-reduction of selenate are also reviewed.INTRODUCTION Selenium in Mining and Mineral Processing Effluents Similar to sulphate and metals, selenium presence in mining and mineral processing wastewater originates from minerals contained in the mined deposits. Therefore, no organoselenium species are typically present in these kinds of waters and inorganic species including selenite (SeO32-), selenate (SeO42) and elemental selenium account for the majority, if not all, selenium present in these streams. Elemental selenium is not always present in mine water but is often contained in smelter wastewater. To comply with new environmental regulations, a successful water treatment plant must remove selenium from all these forms effectively and economically without generating by-products that are difficult to dispose of or manage. Elemental selenium can be dealt with using filtration or gravity separation in clarifiers often assisted by flocculants and/or coagulants. Mine impacted waters typically contain other forms of suspended solids which are removed from water in this way. Once the solids are removed, the selenium species that remain untreated are the dissolved forms. In mining waters this is mostly selenate with small fraction of selenite. In smelter wastewater, the majority could be selenite. It is well established that tetravalent selenium is readily removed from water by using ferric iron co-precipitation at pH > 4 (NAMC SWG, 2010). Ferric hydroxide/ferrihydrite solids act as the adsorbent for tetravalent selenium when it is in one of the ionic forms of biselenite or selenite. This treatment for tetravalent selenium is highly efficient. Therefore, tetravalent selenium removal is generally not an issue and is often easily incorporated into lime neutralization or unit operations such as electrocoagulation used for removing other metals present in mine impacted waters. Another option of dealing with tetravalent selenium is sulphide precipitation in acidic pH which produces SeS2 and can separate selenite from other metals and/or sludge produced at neutral to alkali pH."

Jan 1, 2017

By Edouard Asselin, Tasawar Javed

This study was conducted as a part of ongoing work to characterize sulphide concentrate leach residues generated under CESL (Cominco Engineering Services Limited) and Vale pilot and demonstration plant medium temperature (150 °C) process conditions. Three different samples were analyzed. Derivative samples were prepared by extracting gypsum, sulphur and amorphous/poorly crystalline iron oxyhydroxide phases from the leach residues. Thermal behavior of the samples was studied by thermal gravimetric analysis (TGA) and differential thermal analysis (DTA) in the temperature range 25 to 800 °C in both air and nitrogen atmospheres, with XRD analyses both before and after heating. Thermal transformation temperatures for different iron oxides/oxyhydroxides present in hydrometallurgical leach residues vary over a wide range which suggests the variable crystallinity of the phases. Raman spectroscopic analysis was carried out to help identify the type of iron phases in the residues. Furthermore, hydroxylamine hydrochloride (HaHC) and oxalate extractions were used to compare the fractionation of the amorphous/poorly crystalline iron phases in the residues. Given the compositions of the residues, any thermal events in the temperature range of 200 °C to 480 °C were attributed to amorphous/poorly crystalline iron phases.

Jan 1, 2014

By P. Mpofu

In this work, the modification of interfacial chemistry of colloidally stable kaolinite clay dispersion has been carried out to improve its flocculation performance and dewatering behaviour. Synergistic action between dispersion pH, hydrolyzable metal ion and high molecular weight polymeric flocculant structure type (anionic polyacrylamide-acrylate copolymer (PAM) and non-ionic polyethylene oxide (PEO)) was found to play a pivotal role in inter-particle bridging, the enhancement of the settling rate and extent of consolidation of the pulps. Flocculation with PEO led to higher settlings rates in acidic than alkaline pH, whilst for PAM, the maximum dewatering rate was achieved in the neutral pH range 6 - 7.5. Upon shear, the PEO flocculated pulps showed dramatic improvement in consolidation to 40 wt%, the extent of which was greater at lower than high pH values. For PAM-based pulps were however, not shear-responsive, lower sediment solid contents of 15 - 23 wt% was observed between pH 3 and 11. Hydrolysable metal ions, Mn(II) and Ca(II), used respectively at pH 7.5 and 10.5 in conjunction with PAM and PEO, significantly enhanced the settling rates and consolidation of the pulps. The findings exemplify the strong links existing between pH-mediated particle surface chemistry. polymer structure-conformation, inter-particle bridging and dewaterability of kaolinite dispersions.

Jan 1, 2004

By J. Gebhardt, D. McBride, C. R. Bennett, Croft. N., M. Cross

A comprehensive model of solution flow through heap leach systems requires a numerical solution with the ability to predict variably saturated-unsaturated flow through porous media domains that contain materials with spatially variable properties. The types of flow associated with stockpile leach processes lead to flow problems, such as infiltration into dry soil, drainage, perched water tables and flow through heterogeneous materials. Computational methods for modelling this class of flow behaviour are conventionally based on the classical Richards' equation. However, the governing equations are highly non-linear, difficult to solve, and require iterative numerical solution methods. The pressure-based form of the Richards' equation suffers from poor mass balance, while the mixed form can possess convergence difficulties. An adaptive transformed mixed algorithm is described, which reduces the non-linearity of the problem, optimizes the time step size, and provides a fast, numerically robust scheme that significantly reduces computation (or CPU) time. This method is shown to give fast, accurate solutions on a number of complex flow problems. The utility of this algorithm is illustrated through its implementation within the PHYSICA computational modelling software, which incidentally, provides a framework for a comprehensive heap leach model.

Jan 1, 2005

By R. O. Burt

The original flowsheet of the TANCO mill consisted of a simple two-stage gravity circuit for the recovery of the tantalum concentrates. With decreasing grade and grain size of the tantalum minerals, considerable modifications to the circuit have been required. This paper discusses the various recent improvements carried out 011 all stages of the flowsheet, which have resulted in a 10% increase in recovery. Future improvements, including on stream analysis, and the possibility of tantalum flotation , are also discussed.

Jan 1, 1979

By V. G. Papangelakis, G. A. Moldoveanu

"Rare earths adsorbed on clay minerals are easily recovered via ion exchange during leaching with inorganic monovalent salt solutions. The leaching efficiency of various salts at 0.5M and 25°C was investigated as a function of cation type and salt system (sulphates vs. chlorides). (NH4)2SO4 was identified as the lixiviant of choice and a procedure was established to investigate the influence of lixiviant concentration, temperature, pH and agitation on desorption kinetics and REE extraction levels. It was determined that the kinetics were fast and the optimum leaching conditions (for >80% total REE extraction) required pH below 5 and moderate temperatures (<50°C). INTRODUCTIONRare earth elements (REE) are at the core of numerous advanced applications due to their various uses in high strength permanent magnets, lasers, automotive catalytic converters, fiber optics/superconductors, and electronic devices (as phosphors in TVs and display screens for computers and cell phones). Because of the ongoing development of new technologies, there is an increased demand for REE in the international market, with emphasis on identifying new resources to insure an adequate supply for present and future use. World production of rare earths is dominated by China, the United States and Australia; however, in terms of resources, China dominates the world potential with reserves estimated to be over 90% of the total (Chen, 2011).The main commercially significant REE sources, as reviewed by O’Driscoll (1991) are bastnasite (carbonate) and monazite (phosphate) minerals, containing up to 70% wt. rare earth oxides (REO). In spite of being high grade, these ores are associated with elevated recovery costs due to difficulty in mining, separation and beneficiation. Moreover, aggressive conditions are required to solubilize the REE from the mineral, such as leaching with hot, concentrated acids or baking in 70% NaOH (Gupta & Krishnamurti, 2005)."

Jan 1, 2012

By H. J. McQueen

Pressure welding is a solid state joining technique that depends on bringing the parts into sufficiently close contact that inter-atomic bonds are achieved. Pressing is more effective at elevated temperatures where plastic flow causes the asperities to collapse; improved application conditions are derived from hot-work research to clarify temperature and strain rate dependence of hot strength and ductility. The substructure evolution systematically studied in hot working to determine dynamic recovery or recrystallization is applied to clarifying that developed in welding. The various processes are affected differently by work-piece geometry and final shape requirements. In addition to pre-cleaning of the surfaces, the plastic flow helps disperse the remaining oxide layers as was originally exemplified in blacksmith hot forging of layered sword blades and in bellldie welding of wrought iron tubes. The presentation critically compares the utility for various materials and configurations of simple pressure, ultrasonic application, diffusion, explosive, rotary and linear friction and friction-stir processes. Diffusion bonding (primarily Ti) with light cleaning, low pressure, little distortion in protective furnace atmosphere contrasts strongly with the heavy upsetting in friction welding, or complex alloy mingling and substructure variations in friction stir joints.

Jan 1, 2011

By P. Mišcevic, B. Kavur, I. Vrkljan, N. Štambuk Cvitanovic

It is known from earlier and recent research that mechanical properties of intact rock like uniaxial compressive strength (UCS), Young's modulus (E) and Poisson's ratio (?) are influenced by shape deviations of test specimens as deviations from the ideal cylinder. That impact can be significant at certain level of inaccuracy of specimen preparing, and it should be objectively evaluated and controlled in testing. The effects of intact specimens side straightness, ends flatness, ends parallelism and perpendicularity to the specimen axis, on UCS, E, and ?, measured in several actual ways during laboratory compression tests, were determined by previous research on 90 homogeneous specimens of limestone. In this paper, we subject these new experimental results to Response Surface Methodology (RSM) to model the mentioned dependence, to identify significant connections of variables and to evaluate the conclusions obtained directly from experimental phase. This study indicates how the responses of the model (outputs) – parameters UCS/E/??of limestone rock depend on factors (inputs) – parameters of specimen shape deviations like flatness R, parallelism P and perpendicularity O, assuming modern test machines with spherically seated upper platen. Starting from general RSM model with three factors (R, P, and O), we investigated the multiple linear regression models of specific mechanical property (UCS, E, and ?). Using the NCSS program ("NCSS 2004 and PASS 2005") in several steps, final models with very high coefficients of determination were developed for properties with the most evident effects of specimen shape deviations: nine models for strength UCS and UCS50 (equivalent UCS for specimen with 50 mm diameter), and three models for ?L (Poisson's ratio calculated from axial deformations measured on the entire specimen length). These statistical models with their response surfaces further strengthen and confirm the results and conclusions from the experimental phase. The critical values of R, P, and O are established using an additional statistical analysis to determine the lower and upper engineering limits. These findings set the basis for the new eligibility criteria for specimens of limestone (and similar rock with UCS about 100-150 MPa) in further testing of strength and deformability.

Jan 1, 2015

By M. Tardif, F. L. -Lavoie, M. Ruel

"In mineral processing, it is often very difficult to reliably measure several key operation variables. The harsh environment and high temperature encountered in pyrometallurgy processes lead to some difficulties when selecting the instruments, valves and actuators. If an important variable cannot be measured or manipulated adequately, controlling it can really become a big challenge. Sometimes, it is simply impossible to find the perfect equipment for the task. To help overcome these difficulties, a different approach is required. This approach will not correct the inherent problems related to the instruments and valves, but will cope with these problems. This article will demonstrate how modern process control techniques can be used to solve complex problems while remaining easy to implement. In this article we will described how soft sensors and multivariable fuzzy logic control were implemented at Koniambo Nickel to stabilize the furnace feed and allow for safe and reliable operation of an 80 MW DC arc furnace.INTRODUCTION Process Overview The process plant at Koniambo Nickel SAS is located in the North Province of New Caledonia, 310 km north of Noumea. The nickel-bearing ore is mined in the nearby Koniambo massif. After being screened and crushed, the ore is transported to the processing plant using a 12 km conveyor. After stacking in two blending piles, the ore, containing 2.3% nickel, is fed to the processing plant where it will go through the NST process (Nickel Smelting Technology) before being sent to refining and shotting. This article will focus on the improvement to control of the NST processes. The first steps of this process consist of milling the ore and removing all moisture through calcining (Figure 1)."

Jan 1, 2017

By B. Wasmund, M. Parravani, M. Jastrzebski, Z. Coull

"One of the main drivers of overall profitability of pyrometallurgical vessels is refractory lining campaign life. Increased economic pressure to improve vessel life requires innovative solutions to the problem of refractory cooling. Hatch has recently developed a high-intensity, waterless cooling system that bridges the performance gap between external shell cooling and internal water-cooled copper elements. External shell cooling has a limited effectiveness in protecting the refractory lining, because it is thermally insulated from the hotface of the lining by its thickness. This situation does not improve until the lining itself has become worn near the end of the campaign. The patented technology developed by Hatch overcomes this problem by positioning high-velocity air-cooling channels within the lining, closer to the hotface where the cooling benefits can be realized throughout the entire duration of the campaign. The current paper presents the development and application of Internal Air Cooling technology as well as results from the pilot campaign in an operating commercial vessel. Various adaptations for this novel, cost-effective and inherently safe system are also discussed."

Jan 1, 2015

By Victor Dolmage

Introduction Although gold production in British Columbia began in 1859, lode gold was not produced till 1893. Since 1900, the annual production of lode gold has fluctuated between $3,000,000 and $6,000,000. About twenty per cent of this production may be regarded as by-product gold from base metal mining. The remainder comes from a few isolated but important mines, such as the Rossland mines, Nickel Plate, Surf Inlet, Premier, Pioneer, Bralorne, Reno, and Cariboo Gold Quartz, and from several less important mines. All of the above, except Pioneer, Bralorne, Reno, and Cariboo, are approaching or have reached the point of exhaustion, but all are now receiving, under the stimulus of the. present gold-mining boom, drastic resuscitative treatment, with, in some cases, signs of resurrection. Notwithstanding this, however, the main interest at the present time is focussed on the Bridge River and Cariboo fields. Both these fields were discovered in the early &apos;sixties&apos; and, apart from the Cariboo placer production, both have from time to time contributed small amounts of lode gold; but it is only during the last two years that the real possibilities of these areas were discovered. and that they began to assume the appearance of goldfields of major importance. The two fields are sorme three hundred miles distant from one another and contain deposits of distinctly different types, so that the only reason for including them in one article is the fact that they came into prominence more or less simultaneously and at a time coinciding with, but not otherwise related to, the present gold-mining boom.

Jan 1, 1934

By J. Lu, D. G. Ivey, H. Henein

Microalloyed steels are widely used in the oil and gas industry. They are a class of high strength, low carbon steels containing small additions of niobium (Nb), titanium (Ti), molybdenum (Mo) and/or vanadium (V). These steels have good strength, toughness and excellent weldability, which are attributed in part to the presence of nano-sized carbides, nitrides and carbonitrides. In the pursuit of developing higher strength microalloyed steels, it is of great interest to quantify the size, distribution, volume fraction and chemical speciation of these precipitates. However, characterization techniques suitable for quantifying fine precipitates are limited. Possible characterization techniques include SEM, TEM and matrix dissolution. A comparison is presented of the various techniques.

Jan 1, 2005

By L. A. Ayres da Silva, J. P. G. Negri, A. L. M. Ayres da Silva

"Rock hardness is dependent on the type and quantity of the various mineral constituents of the rock and the bond strength that exists between the mineral grains. As the book “The Complete ISRM Suggested Methods For Rock Characterization, Testing and Monitoring:1974-2006” explains, hardness is a concept of material property. As such, the quantitative measure of hardness depends on the type of the test employed.Among the three types of tests that have been used to measure the hardness of rocks and minerals: 1) indentation tests; 2) dynamic and rebound tests; 3) scratch tests, the authors of this paper chose indentation tests, more specifically the Vickers test, and complementary verified the correlation between the results of the Schmidt sclerometer tests (rebound tests) and the Vickers microhardness tests in a set of the same 9 (nine) granite rocks.The objective of this research was to verif y the correlation of one created index, based on the Vickers test that can be able to represent the rock material hardness. We know that Vickers tests determine the microhardness of individual rock minerals. A pyramidal shaped diamond is applied to the surface with a specified force. The area of the permanent residual deformation divided by the applied force is a measure of the hardness. Using the relative participation of the mineral components of the rock, we established a hardness index denominated EVM (Equivalent Vickers Microhardness).The correlation of the EVM with others strength properties and application parameters like UCS (Uniaxial Compressive Strength) to study sawability of granite blocks have presented very good results. The association of equivalent microhardness with others strength parameters, allowed to find powerful algorithms for analyzes of the rock materials behavior under diversified circumstances, as the sawability of granite blocks, as we can see in Fig. 1.Other very interesting correlations were found as the EVM values and that were obtained by the use of the Schmidt impact hammer for the superficial hardness determination."

Jan 1, 2015

By E. Ghali

"Corrosion of support system components (e.g., bolts, mesh, plates) is a safety and economic concern in underground mines. This paper reports the results of a five-year study wherein corrosion coupons were installed at select locations in participating mines, recovered at regular intervals, analyzed for signs of corrosion, and tested to quantify loss in capacity. Complementary tests were conducted on recovered mesh and friction bolt specimens. The data provide insights into contributing factors for support systems corrosion, which aid in the selection of appropriate support strategies and reliable assessment of the useful life and need for rehabilitation of a support system.RÉSUMÉ La corrosion des composantes des systèmes de soutien (p. ex. boulons, grillages et plaques) est une préoccupation économique et de sécurité dans les mines souterraines. Cet article présente les résultats d’une étude de cinq ans pendant laquelle des coupons de corrosion ont été installés à des endroits spécifiques dans les mines participantes; ces coupons ont été retirés à des intervalles réguliers, analysés pour des signes de corrosion et mis à l’épreuve pour quantifier la perte de capacité. Des essais complémentaires ont été effectués sur les grillages récupérés et sur les échantillons de boulons d’ancrage. Les données aident à comprendre les facteurs qui contribuent à la corrosion des systèmes de soutien, ce qui est utile dans le choix de stratégies appropriées de soutien et pour une évaluation fiable de la durée de vie utile et du besoin de remise en état d’un système de soutien."

Jan 1, 2015