Search Documents

By A. G. Allten

EXAMINATION by metallographic and X-ray diffraction means of an austenitic steel containing 0.06 pct C, 1.26 pct Mn, 0.38 pct Si, 21.15 pct Ni, 18.72 pct Cr, 3.07 pet W, and 9.14 pet Mo indicated that a - phase, which had not been reported in the literature, existed in this steel. Both the s and car-bides of the M6 C type were present in the as-forged steel. The carbides dissolved completely in the aus-tenite at approximately 2200°F (1205°C). The s, however, was present at all temperatures up to the solidus temperature of the steel at approximately 2375°F (1300°C). Ferrite was not found in any condition of the steel. The faintness of some of the s lines in X-ray patterns obtained from samples of the steel made it desirable to isolate the s prior to verification of its entire pattern. It was found that the s phase could be separated from samples of the steel which had been water quenched from 2250°F (1230°C) by dis-

Jan 1, 1955

By O. J. Kensok

THE literature contains three previous studies of the chemical activities of Cd-Mg alloys: Trumbore, Wallace, and craigl obtained chemical activities of magnesium at 543" by performing electromotive-force measurements; Borg and irchenall calculated activities at 590°K based on vapor-pressure measurements of cadmium over Mg-Cd alloys by the Knud-sen effusion method; and Terpilouski and arcka measured the chemical activities of magnesium in the liquid state by means of electromotive-force measurements. In this study the vapor pressure of cadmium was determined over nine solid Cd-Mg alloys in the temperature range 571" to 697°K by the Knudsen effusion method. This study was prompted by the lack of precision in the data reported by Borg and Birchenall. Knudsen cells used during this study were fabricated from 0.020-in.-thick tantalum tubing. The tops and bottoms of the cells were cut from 0.010-in.-thick tantalum sheet, press-fitted, and welded in place. The orifice was drilled in the cell top and subsequently reamed to a knife-edge thickness. The diameter of the orifice was measured with a traveling microscope capable of reading 0.0001 cm. The sample was heated by means of a resistance

Jan 1, 1967

By J. Menashi, D. A. Douglas, A. S. Rappas

Aqueous solutions of Na2Cr04 are reduced with CO to produce hydrous Cr2O3 and NaHCO3/Na2CO3. CH3OH, HCOO- and HCHO in the presence of CO2 also reduce Cr(VI) and yield similar products. It is shown that the rate of Cr(VI) reduction can be represented by the expression -d [Cr(VI) ]/dt = k[Cr(VI)]0.5[R], where [R] is the aqueous phase concentration of CH3OH, HCOO- or CO. With these three reductants, the activation energies for the reduction processes are comparable and are of the order of 100 kJ/mol (43,000 Btu per lb mol). Rapid reduction rates are attained at temperatures in excess of 220°C (428°F). With these three reductants, a green acid-insoluble readily filterable hydrous Cr203, is formed. With HCHO, significant reduction of Cr(VI) occurs at about 80° to 100° C (176° to 212° F). The product is an acid-soluble violet modification of hydrous Cr203. Solutions of Na2CrO4 contaminated with Mo(VI) and W(VI) can be reduced to yield a Cr2O3 product with significantly reduced contaminant levels.

Jan 1, 1986

By Mark L. Requa

(San Francisco fleeting, October, 1911.) DURING the past two years California has developed a new and important oil-field : I refer to Midway. This field produced the famous Lake View gusher, which is credited with a total production in excess of 8,000,000 barrels. Fortunately for the oil industry of the State, this well is now a thing of the past, and nothing save a great crater-like opening marks its location. The pipe is entirely worn away and gone ; and it is a matter of serious doubt if there can be anything done that will cause the well to produce again. Fortunately, also, there have been no, other wells in that field or elsewhere throughout the State that in any way compared with the Lake View. Midway is noted for large wells, of from 500 to 2,000 barrels production; but the decline is rapid, and a few months serve to bring the output down to a few hundred barrels. In the oil-territory heretofore blocked out as proved and probable, there have been, during the year, many changes. Some areas which were expected to be fairly productive have apparently failed; others, more strictly "wild-cat," have come in; while in some of the older fields there are properties which are beginning to show evident signs of exhaustion. The total area of proved territory will therefore probably suffer but small increase, when balances are struck off. The increase of new area has come from extensions of the Midway field, the development of a field in Lost Hills and Belridge, and extensions of the Fullerton-Whittier field in southern California. In these later developments, down to date, the fresh area absolutely proved is not much in excess of 3,000 acres. Recent developments in Coalinga indicate the possible extension of that field to the south, but at great depth. Coalinga is still the most northerly field of any consequence in the State. The Kettleman Hills have hitherto brought in nothing, although a

Apr 1, 1912

The following list of US companies, mines, and mills engaged in uranium production was compiled by the Health and Safety Analysis Center, Mine Safety and Health Administration, in Denver, Colo. The list includes those companies reporting to the Center in 1978. Thanks to D. K. Walker, Chief of the Health and Safety Analysis Center, for providing the information to MINING ENGINEERING.

Jan 10, 1978

By Thomas T., Read

T HE preceding chapter has recorded the initiation of mineral industry education during the period 1890-1910 in numerous institutions that had not previously offered it. It should also be emphasized that in many institutions where instruction had begun before 1890, as recorded in earlier chapters, but had not yet become firmly established,, this period was one of marked growth and development. This was not universally true, however, for at the Universities of Pennsylvania, Michigan, Illinois, Wisconsin, Washington (St. Louis), Iowa, Vanderbilt and Tennessee, and at the Polytechnic College of Pennsylvania, mineral industry instruction was being dropped during this period, instead of gaining in strength. It is necessary to emphasize this, because writers on the subject have not infrequently , attempted to make a much too simple correlation between mineral -discovery or production and the intensity of student interest in mineral industry curricula. It would naturally be true that periods of large mineral production would, in general, coincide with cycles of business prosperity, and the latter are conducive to starting new ventures, educational as well as business. It should be equally evident that opportunities for business and professional success might, in such periods, appear to increase at a more rapid rate in industries other than mineral, or in the utilization of minerals rather than in their production. The author has not been able to perceive any simple and clear relation between interest in mineral industry education and mineral discovery, production, and utilization, or general business prosperity. On the contrary, the more the problem is studied the more complex the factors involved in it appear to be. In a later chapter an attempt will be made to analyze them in more detail.

Jan 1, 1941

By Y. C. Liu, R. H. Richman

The effects of gel,manium and tin on the deformation and 9-e-crystallization textures of copper have been explored in detail with in the copper-rich terminal solid solutions. Addition of solute to copper produces a change in deformation texture from the copper type to the 70 :30 brass type. This transition has been measured quantitatively The types mid proportions of recrystal-lization components have been determined as a function of com-position, and correlation of recrystallization components with specific deformation components is discussed. On the basis of information available in the literature, it has been suggested that the effect of solute elements on the recrystallization texture of copper

Jan 1, 1961

Bernard MacDonald, Guanajuato, Mexico (communication to the Secretary*):—Mr. Iceyes's paper is very interesting to me because of my personal experience with the development of the ore-deposits of Lake Valley.

Jan 1, 1909

By Robert M. Weidenhammer

For years before the war, Coal had the reputation of being a sick industry. Currently it is operating at peak production and succeeding pretty well in keeping out of the red. But, says Mr. Weidenhammer, it will have a relapse as soon as the war ends unless (1) working capital can be built up; (2) it gets the support of the people and Congress; and (3) a truly long-range national fuel policy is formulated.

Jan 1, 1943

By Edgar L. Weinberg, W. Horatio Brown

The Austinville-Ivanhoe lead-zinc deposit occurs in the Lower Cambrian Shady dolomite. This deposit is located in southwestern Virginia in the faulted and folded Appalachian Valley and Ridge province. The ore bodies resemble the chimmey and manto deposits of northern Mexico and are formed by replacement and filling. They are confined to certain favorable zones of the Austinville and Ribbon members of the Shady. Structural and stratigraphic factors combine to control the location and form of the ore bodies. In certain places secondary oxide enrichment of the zinc minerals has contributed to the economic development of the area. It is concluded that the ore is epigenetic and is deposited by hydrothermal solutions rising through the fault "plumbing." Classification is epithermal-telethermal.

Jan 1, 1968

By C. A. Gibbons

AFTER nine years of extremely de- pressed business, marked mostly A with red ink on the balance sheets of most coal companies and with an increasing internal competitive struggle for diminishing markets, somewhat of a change appeared during 1939. Shipments increased and prices generally firmed, giving the coal industry increasing optimism and encouragement for the future. Specifically, it now appears that bituminous coal production for 1939 will approximate 378,000,000 tons, and anthracite production will approximate 47,500,000 tons, bituminous production being around 14 per cent ahead of 1938 and anthracite production 12 per cent better. The curve on p. 31, showing both bituminous and anthracite production, furnished by the bituminous coal division of the Department of the Interior, shows graphically most of the 1939 monthly production and clearly illustrates the increased production.

Jan 1, 1940

By C. Chu

An investigation has been made of the radial heat-wave process using a mathematical model in two-dimensional cylindrical coordinates. This model considers combustion, convection and conduction inside the reservoir, but only conduction in the bounding formations. From a study of the general features of the process, an important phenomenon has been revealed, namely, the feedback of heat into the reservoir on the trailing edge of the heat wave. The effects of various process variables on the performance characteristics of the process have also been investigated. It was found that up to the time when the combustion front reaches a given point, the per cent heat loss, provided it is not higher than 40 per cent, is approximately directly proportional to the square root of thermal conductivity arid fuel content, but inversely proportional to the square root of gas-injection rate and oxygen concentration. The effecr of reservoir thickness is more pronounced, since halving the thickness doubles the per cent heat loss. The most decisive factor in determining the center-plane peak temperature is the fuel content of the reservoir. Within the temperature range investigated, doubling the fuel content doubles the peak temperature in the early stage, but the rate of decline of the peak temperature is high. Reservoir thickness is also a very influential factor. The peak temperature is lowered when the thickness is reduced; however, the effect of thickness becomes less pronounced when the thickness is high. Reduction of oxygen concentration increases the peak temperature in the early stage but lowers it afterwards because of the higher rate of decline of the peak temperature. Increase in gas injection rate or decredse in thermal conductivity geives a higher peak temperature which stays high for a longer period. The propagation range of the heat wave is chiefly governed by the fuel content of the reservoir. An increase of 0.2 1b/cu ft in the fuel content increases the propagation range by 100 per cent. The propagation range is more than doubled by doubling the gas injection rate, or reservoir thickness, or by reducing the thermal conductivity by 50 per cent. Comparatively, oxygen concentration has less effect on the propagation range. INTRODUCTION Several investigators have conducted theoretical studies of a radial heat wave. Vogel and Krueger1 studied a system with a moving cylindrical heat source of constant temper- ature, considering conduction in the radial direction only. Ramey2 included conduction in the vertical direction in his studies. Bailey and Larkin2 attacked a more general problem where initial well heating, vertical heat losses and arbitrary frontal velocities were included. In all these studies, however, conduction was considered to be the only means of heat transfer. Bailey and Larkin in a later paper included the effects of convection in a study involving both linear and radial geometries. Vertical heat losses were neglected in the radial case. Katz5 studied a similar problem in a one-dimensional radial model, using a heat-loss coefficient to account for vertical heat losses. Selig and Couch6 mployed a cylindrical model and investigated two limiting cases. In one case they considered no heat loss from the reservoir whereas in the other they assumed a constant temperature at the interface between the reservoir and its bounding formations. Thomas' studied a more general case but assumed a permeable bounding formation so that the convection effect is not confined to the reservoir. In the present work a more realistic and more generalized model is used. It involves a two-dimensional cylindrical system with combustion, convection and conduction inside the reservoir, but only conduction in the bounding formations. The purpose is to establish the temperature distribution both inside and outside the reservoir, to study the general features of the radial heat wave process, and to investigate the effects of various process variables on the performance characteristics of the process. THEORY We fist consider a circular porous reservoir of thickness H extending vertically from y = — H/2 to y = + H/2. The reservoir extends from a well bore radius r, to an external radius re. A stream of oxygen-containing gas is introduced into the reservoir through the wellbore. The oxygen-containing gas reacts with the fuel contained in the reservoir and forms a combustion front wherever the prevailing temperature can support the combustion. It is here assumed that this combustion front constitutes a cylindrical surface source of heat having an infinitesimal thickness in the radial direction and extending vertically throughout the whole thickness H. This is designated as Region I. We next consider a Region II corresponding to the upper and lower formations bounding the reservoir, extending from y = — - to y = — H/2 and from y = + H/2 to y = + m. Since r, is very small, we may assume that the two bounding formations have the same dimensions, symmetric with respect to the center plane of the reservoir. In this way, we may take the upper half of the system alone into consideration. In contrast with

By Krahmann, Rudolf

THE following is an account of a survey undertaken to test the possibility of outlining a kimberlite pipe by magnetouietric methods. Kimberlite is a basic igneous rock closely related to melilite-basalt or alnoite, which occurs either in the form of volcanic plugs or as dikes intruded into rocks of various types and geological ages up to and includ¬ing the Lower Cretaceous. The famous diamond mines of South Africa are all in kimberlite pipes and these pipes are probably the original source as well of the vast alluvial deposits found in various parts of the country. The pipe chosen for this experiment is one that ' occurs on the farm Goedgevonden No. 20, about sixteen miles north of the village of Klerksdorp and ninety miles southwest of Johannesburg. Some prospecting has been done on this pipe and diamonds were produced from it but not in paying quantities. The magnetometric survey was made in June, 1932, by R. Krahmann and H. Wallisch and the results are shown on the accompanying plan. On the plan are shown also the boundaries of the pipe as exposed at the surface and details in regard to the surrounding foundations. These are taken from a geological survey made at a later date by W. Beetz, of Johannesburg.

Jan 1, 1935

By Scott Tzcrner

WITHIN recent years people have begun to realize the importance and significance of the mining and allied industries. The leading part the engineer plays in civilization is becoming recognized. However accurate quantitative knowledge of the industrial importance of mining is still seldom possessed except by those close to this business. It is true that there are a few who go to the extreme and represent the whole progress of civilization as a reflection of man's gradual mastery of mineral utilization, but on the whole, the magnitude of the-industry is underestimated. In this paper I shall call attention briefly to the importance of mining in the United States, in Canada, and in the world. Ordinarily, the annual primary mineral production of the United States is about $5,500,000,000. The average for the last 5 years has been a little over that, but last year, sadly enough, it was less than 31/4 billion. Just now, we are on the decline, and have been for the last two years. In Canada, the 5-year average was about $268,000,000, and last year it was 227 million. Due in part to gold mines (in 1930, for the first time, Canada's gold production exceeded that of the United States), the Canadian average is holding up better than ours. Average world mineral production over the last -5 years has been estimated at about $12,000,000;000 whereas in 1931 it was less than than 8 billion.

Jan 1, 1932

By Robert F. Mehl

Jan 1, 1944

By Robert F. Mehl

Jan 1, 1944

By KENNETH CITTISGHAM

During the year 1945, the total number of wells drilled in Ohio, including the. non¬productive wells, was 1034. For the 10-year period ending with 1945, the average completions per year were 1125, the least number being 910 in 1938, and the maximum 1561 in 1941. The proportion of dry holes in 1945 was 37 per cent?about the same as for the year 1944 but exceeding the 10-year average, which was 34 per cent. The number of oil wells completed exceeded the number drilled in 1944 by about 30 per cent, the average initial per well being the same in both years. Gas-well completions were approximately 10 per Cent less than in 1944, with the average initial per well about 5 per cent greater. The difference in number of oil and gas wells in the two years was in Berea and Clinton completions, as the number of oil wells increased about 30 per cent, owing to greater activity in the two sands named, while the number of gas wells decreased because of fewer completions therein.

Jan 1, 1946

A comprehensive, systematically structured mineral evaluation system is a prime requirement for objectively assessing mineral supply impacts on the economy. The Minerals Availability System developed by the US Bureau of Mines is a step in the right direction-a well-organized unraveling of the mineral supply network, structured in format to allow quick retrieval for rapid listing, supply analysis, and other uses.

Jan 9, 1977

By S. Atak, M. C. Fuerstenau

Clean quartz cannot be floated with a high molecular weight sulfonate as collector at any pH. Good flotation is achieved from pH 6 to 12 when Pb is added at low additions of sulfonate. The active species of lead responsible for flotation is shown to be Pb(OH), which in the presence of sulfonate forms precipitated lead-hydroxy-sulfonate, the apparent collector in these systems. The ratio of collector to metal ion addition is critical for flotation to be effected at a given value of pH. At low Pb++ additions, the constant, k, k = (hydroxyl activity)/(sulfonate addition)', must be equalled or exceeded for flotation to result. Similarly, at high additions of Pb ++, k1 = (hydroxyl activity)/(sulfonate addition) " must be exceeded. Previous work has shown that clean quartz cannot be floated at any pH with a high molecular weight sulfonate as collector.'" Flotation can be effected, however, when a polyvalent metal ion is added to the system in a pH region in which the metal ion is hydrolyzing to its first hydroxide complex. Although the basic phenomenon responsible for activation is apparently metal ion hydrolysis, the amount of collector added in relation to the amount of metal ion is critical. In fact, Schuhmann and Prakash,3 and Gaudin and Rizo-Patron4 have demonstrated that this ratio of collector addition to metal ion addition determines whether any flotation is possible at a particular value of pH. The object of this paper is to explain and quantify the relationship between collector and activator additions as a function of pH. For this work, Pb++ was selected as activator, and a high molecular weight sulfonate was chosen as collector. EXPERIMENTAL MATERIALS AND METHODS Sodium alkyl aryl sulfonate (mol wt 450) was used as collector. Reagent grade n-amyl alcohol was added as frother, and pH adjustments were made with KOH. Lead was added to the systems as the chloride salt. Conductivity water, made by passing distilled water through an ion exchange column, was used in the investigation. Quartz was prepared by leaching the sized sample

Jan 1, 1965

By W. Rostoker

IN the course of the development of the phase equilibrium diagram for the system Zr-Cr,' the structure of an as-cast allov having the composition ZrCr2 was analyzed and established to be isomorphous with MgZn2 (C14, hexagonal lattice, 12 atoms per unit cell). In a recent paper on the same system, Hayes, Roberson, and Davies' report for the ZrCr2 phase an isomorphy with MgCu2 (C15, cubic lattice, 24 atoms per unit cell). It appeared that this conflict might be resolved by assuming a high and low temperature modification for ZrCr2. That this was the case with the phase TiCr2 has recently been demonstrated by Levinger." Specimens of ZrCr2 annealed at 1200°, 1100°, 994", 900°, 834", 800°, and 700°C, respectively, and subsequently quenched were examined by X-ray diffraction analysis. It was successfully demonstrated that a transition from the MgZn, structure at lower temperatures to the MgCu, structure did occur at some temperature between 900" and 994°C. Table I lists the observed structures at the various annealing temperatures. In Table II, a summary of line spacings and intensities is given for each of the allotropic modifications. The first six lines of the MgCu2 structures have been located in the table to illustrate the close similarity between the patterns. Lattice parameters of the two modifications were calculated by a least squares solution of equations for interplanar spacings for a series of high angle lines. The results are as follows: MgZn2 type - c = 8.262 kX, A = 5.079 kX. MgCu2 type — a = 7.195 kX. It is interesting to note that TiCr2 behaves in reverse fashion yn that the MgCu, structure is the low temperature modification and the MgZn2 structure is the high temperature modification. References lR. F. Domagala, D. J. McPherson, and M. Hansen: This issue p. 279. 'E. T. Hayes, A. H. Roberson, M. H. Davies: Trans. AIME (1952) 194, p. 304; Journal of Metals (March 1952). 3B. W. Levinger: Trans. AIME (1953) 197, pp. 195-196; Journal of Metals (February 1953).

Jan 1, 1954