Search Documents

By Michael R. Birkos

A new electrotelluric prospecting technique allows the mapping of ore body distribution, lithologic contacts, and voids with accurracy comparable to core drilling. Data is available almost immediately and presented in a format similar to a downhole log. This is done with a passive surface receiver that transduces electrotelluric radiation into an audible signal. Changes in the character of the audible signal lends insight into lithology, porosity, fluid type and medium. Three case histories are presented. The first delineated a paleochannel within a coal seam. The second traced old mine workings and backfill areas. The third identified a high-pressure karst void.

Jan 1, 1986

The whole of the iron ore required by the Broken Hill Proprietary Company Limited at the Newcastle Steel Works, and Australian Iron and Steel Limited, at Hoskins' Kembla Works, is drawn from the Iron Knob, Iron Monarch, Iron Prince and Iron Baron deposits situated in the northern part of Eyre's Peninsula, South Australia.The Iron Knob and Iron Monarch deposits are near the township of Iron Knob, approximately 42 miles W.S.W. of Port Augusta, whilst the Iron Prince and Iron Baron deposits are some 18 miles due south from Iron Knob, in another group of leases, the adjacent township being known as Iron Baron.The ore mined at Iron Knob, Iron Monarch, Iron Prince and Iron Baron is conveyed on the Company's 3ft. 6-in. gauge tramway to Whyalla, on the western side of Spencer's Gulf, approximately 45 miles south by west of Port Augusta whence it is shipped to Newcastle and Port Kembla.SHORT HISTORY.The establishment in South Australia of the lead smelting industry at Port Pirie, Dry Creek and Port Adelaide in the...

Jan 1, 1937

THE question of dealing with the small quantities of copper found in a great many of the purchased ores became a factor of importance when the Sulphide Corporation decided to refine its own lead bullion, as the presence of this impurity has a marked effect on the efficiency of the de-silverizing operations of the Parkes process. Removal of the copper from the base bullion.The copper is removed from the base bullion by drossing, which collects the copper, and at the same time has considerable gold, silver, and lead values. The drassing of the bullion is done in two stages-firstly, at the smelters; and secondly, in thecopper kettles at the refinery. In both cases a "wet" dross is produced, which is subsequently "sweated" in a suitable type of furnace. When "dry" the dross is raked out and stored until enough accumulates to warrant a nUl on dross in the small blastfurnace kept for that purpose. A typical assay of the "dry" dross is as follows...WORKING THE DROSS UP TO LOW-GRADE CU-PB MATTEThe accumulated dross is treated in a small blast furnace with the necessary fiuxes, producing a low-grade Cu-Pb matte and base lead bullion.

Jan 1, 1920

By E Villaescusa, C Drover

The stability of access tunnels is one of the main engineering challenges in deep underground mine construction. Many underground hard rock mining operations are now reaching depths where the induced stresses are such that sudden and violent failure of the excavations can occur very soon after construction. The loading conditions on the installed ground support schemes are often underestimated by conventional engineering design methods. Therefore, the actual loading conditions often exceed the installed ground support capacity. This can result in failure of the excavations and, in extreme cases, potentially closure of mining operations amounting to hundreds of millions of dollars in lost production. More frequently, violent excavation instability at great depth causes operational delays, costly and unplanned rehabilitation, as well as risks to worker safety. In order to address this challenge, this paper briefly summarises a modern, innovative approach to the design and construction of mine development at great depth. The process follows seven main steps. The first step is to characterise the rock mass strength, structure and stress. The second step is a stability assessment, which identifies the plausible modes of excavation failure, based on the rock mass characterisation. The third step is the definition of an excavation geometry which is harmonic to the high stress conditions. The fourth step is to prepare a site-specific face destressing drill and blast design which will reduce the potential for rock mass instability during the development construction cycle. The fifth step is to accurately quantify the expected loading conditions on the installed ground support. The method of doing so is uniquely analytical and probabilistic. It is based on the natural mechanical relationships between rock strength, structure, induced stress and the physical characteristics of the instability, including its mass and ejection velocity. The sixth step of the design process is to specify a ground support scheme arrangement with sufficient strength and displacement capacity to exceed the rock mass demand by a safe margin. The final stage is to install the complete ground support scheme using mechanised technologies which minimise the exposure of the equipment operators to unsupported ground at the tunnel face.

Nov 29, 2022

By D. A. Spencer, L. J. Gardner

In light of the apparent productivity benefits provided by mechanised stoping, Impala Platinum Limited commissioned a study to investigate its possible implementation for mining reserves located 1200 – 1700 m below surface. This paper records the methodology employed for designing a support system for such mechanised mining, as well as initial conclusions of the work done. Preliminary results show the concept to be technically feasible; work was however stopped due to financial non-viability. En considération des bénéfices de production apparents que donne l’exploitation par gradins mécanisée, Impala Platinum Limited a commissionné une étude visant à examiner sa mise en œuvre possible pour des réserves minières situées à 1200 – 1700 m sous la surface. L’étude présente rapporte la méthodologie employée pour créer un système de support pour ce genre d’exploitation mécanisée, ainsi que les conclusions initiales de ce projet. Les résultats préliminaires montrent que le concept est techniquement faisable ; cependant le travail fut arrêté à cause de difficultés de rentabilité. Im Licht des offensichtlichen Produktivitätsnutzens auf Grund mechanisierten Stossbaus, kommissionierte Impala Platinum Limited eine Studie, die dessen mögliche Implementierung für den Abbau von Reserven 1200 - 1700 m unterhalb der Oberfläche untersuchen soll. Dieses Elaborat dokumentiert sowohl die Methode die für das Design eines Unterstützungssystems für eine derartige mechanisierte Abbauweise angewendet wird als auch die anfänglichen Konklusionen der geleisteten Arbeit. Anfängliche Resultate zeigen daß das Konzept technisch durchführbar ist; die Arbeit wurde jedoch wegen der finanziellen Nichtrealisierarkeit gestoppt.

Jan 1, 2003

By H. Sevim

An innovative approach in designing the haulage systems for underground coal mines is discussed in this paper. The haulage systems are formed by serially connected components. Therefore an economic and efficient design of the entire system is necessary. The computer model that uses a heuristic algorithm solves this design problem globally in a single run. It is a probabilistic model because it considers the probabilistic aspects of face operations. It is versatile because it can accommodate any type of mining and belt conveyor network configuration. The hoisting section can be used to design drum or friction hoisting systems for single or multiple level operations. These systems can have two skips in balance or a skip and a counterweight in balance. The model also has the option to internally determine the capacity of bunker(s) and shaft-bottom bin. The objective is to minimize the expected cost per ton of coal hauled from the coal faces to the surface. At the end of the paper is an example that illustrated the capabilities of the model.

Jan 1, 1987

By Marc C. Bétournay

"Surface crown pillars, acting to safely protect underground workers and operations from surface elements, are recognized, herein, as distinct from conventional deeper underground pillars. Moreover, because of the variation in mining and geological conditions that exist from mine site to mine site, each case is viewed as unique. A review of numerous case studies and existing literature indicates that there is little general information or systematic problem-solving approach associated with them.A design process, not unlike that of other engineering disciplines, is presented to correct these deficiencies. As part of its purpose, it will inform operators of the key elements required for design and will address the problems of these appendages. The design, while taking into consideration possible surface crown pillar settings and inherent characteristics, is founded on a step-by-step procedure starting with site investigations through to monitoring or pillar recovery. The process is flexible, in that it incorporates decision making and changes in mining strategy. The purpose of each step is explained and each step is extensively described in terms of the required equipment and methods for field work, analysis and support measures. Analytical formulae and studies from several fields directly applicable to surface crown pillars are also given. Recommendations for future research studies are presented."

Jan 1, 1987

By Z. T. Bieniawski

The efficient and safe design of room-and-pillar coal mines still remains as one of the pressing problems facing the mining industry in the United States. Although much research has been directed to stability of mine roofs and coal pillars, no generally-accepted design method has been formulated. This paper presents a concise procedure for an improved design of room-and-pillar coal mines. Developed as a result of a three-year research effort, the methodology includes essentially three aspects: (i) determination of stable roof spans; (ii) determination of the strength of coal pillars; and (iii) determination of safety factors for room-and pillar coal mining in the United States. It is shown that the presented approach will lead to a greater recovery of coal by a more economical, yet safe, mining operation. Design charts and tables are presented and a step-by-step design procedure for practical mining engineers is explained. Several examples are included demonstrating the use of the proposed design procedure for room-and-pillar coal mines.

Jan 1, 1983

A well known rock mass classification system has been altered slightly to address the issues found under remnant mining conditions. By detail study of the expected fracture patterns and local geology, the rock mass is classified to indicate the condition of the hanging wall prior to mining. The risk level of each mining step is evaluated by calculating input parameters for computer simulations from the actual rock mass condition. Seismic activity is catered for by the understanding that large event rates and large magnitude events reduce the quality of the local rock mass and that the rock mass stiffness should be adapted accordingly. A case study is presented to test parts of the protocol. Un système connu de classification des masses rocheuses a été légèrement modifié pour faire face aux questions posées par les conditions d’extraction de débris. Une étude détaillée des diagrammes de fragmentation et de la géologie locale permet de classer la masse rocheuse pour indiquer la condition du toit avant l’extraction. Le niveau de risque de chaque étape minière est évalué en calculant les paramètres d’entrée pour simulation par ordinateur à partir de la condition réelle de la masse rocheuse. L’activité sismique est prise en compte avec la réalisation que les taux de larges évènements et les évènements de large magnitude réduisent la qualité de la masse rocheuse locale et que la raideur de la masse rocheuse doit donc être adaptée. Une étude de cas est présentée pour tester des sections du protocole. Ein sehr bekanntes Gesteinsmassenklassifikationssystem wurde abgeändert um die Probleme zu behandeln die unter Restabbaukonditionen angetroffen werden. Durch detaillierstes Studium der der zu erwartenden Bruchmuster und der lokalen geologischen Verhältnisse wird die Gesteinsmasse in Hinblick auf die Konditionen der Flözoberseite klassifiziert. Das Risikoniveau für jeden Abbauschritt wird durch die Eingabeparameter aktuellen Gesteinsmassenkondition für die Computersimulation evaluiert. Für die Seismische Aktivitäten wird Sorge getragen durch das Verständnis, daß große Ereignisraten und Ereignisse hoher Größenklassen die Qualität der lokalen Gesteinsmasse reduzieren und daß die Gesteinsmassensteifheit entsprechend adaptiert werden sollte. Eine Fallstudie um Teile des Protokolls zu testen wird präsentiert.

Jan 1, 2003

By Y. Luo

Highwall mining, which is a relatively new mining method, is a preferred and often the only feasible method for extracting coal reserve left by surface mining operations in areas with steep terrain and in closely spaced thin coal seams. Though its safety record is comparable to that of surface mining, failures of mine structures in highwall mines, especially the highwall, have occurred. Methods for the systematic designing of highwall mines to meet the safety and operational challenges are still evolving. This paper presents the results of research into improving the existing design methods and developing new ones for highwall mining operations. The design methodology is aimed at ensuring structural stability of the highwall, roof, web and barrier pillars and preventing subsidence. It takes into consideration the major ground control challenges of soft and layered mine roofs, and interactions from mining closely spaced coal seams. An optimization design process applying a pressure arch concept can be incorporated to improve the recovery rate of coal reserve. A computer program based on the design methodology was developed.

Jan 1, 2015

By S. N. Chadha

INTRODUCTION The work described here refers to the Genesee River Interceptor Southeast Project. This project is a part of the Combined Sewer Overflow Abatement Program, Phase I, for the Rochester Pure Water District, Rochester, New York. Our contract required the design of a 13,200-feet long main tunnel, 14 feet finished diameter, approximately 100-120 Feet below ground; drop shafts and diversion tunnels to deliver surface flow to the main tunnel; a gate chamber whereby the main tunnel is dropped 35 feet, and provision made for connection to the future tunnel in Phase II, as well as a host of other surface structures. Cross sectional dimensions for the structures involved varied from 16 feet circular to a 20'x50' horseshoe, in a competent rock formation consisting of Lockport Dolomite and Rochester Shale. In the construction of a rock tunnel, the problems of the tunnel designers are as follows: 1. To evaluate stresses in the rock as a result of excavation. 2. Design a temporary support system to prevent any rock failure during the period of construction. Design of this temporary support system is empirical. Design loads given by empirical relations are dependent upon the rock quality and size of opening. Temporary support system may either be steel frames closely spaced along the length of tunnel and tied together, in the case of poor rock, or, an even spacing of rock bolts in the case of competent rock. 3. Design a final lining for the service loads. Service loads, in our case of a water-carrying tunnel, are hydrostatic pressure due to ground water, deadweight of lining) pressure of contained water and time dependent rock loading. The constitutive properties of the rock are extremely complex because of discontinuities, pre-existing stresses due to overburden, material symmetries and changes of initial state associated with the process of excavation. The changes of initial state may be changes of stress fields along with the consequent yield of the material or the extension of existing discontinuities.

Jan 1, 1977

By S B. Stewart, C J. Restarick

Over a four-hour period of steady plant operation samples were taken at regular intervals frum points within the grinding and flotation circuits. Size fractions of each composite sample were analysed for lead and zinc values and a comparison made of the behaviour of the lead, zinc and gangue minerals, size by size throughout the whole circuit. Analysis of the breakage behaviour using dynamic mathematical models gave the rates of breakage of each size fraction of each main component. Simulated grinding experiments shaved that the main grinding circuit had some reserve capacity. In the lead flotation circuit all lead values between 150 mesh (Tyler) and 5 ¦m had excellent flotation characteristics, and a major proportion had a high rate of flotation which was practically the same for all sizes. Increase in overall lead recovery would require improvement of the flotation behaviour of ultra-fine lead minerals. These were slav floating and were responsible for approximately half the lead losses in the final zinc concentrate and one thiro of the lead losses in the final tails. All sizes of zinc values between 150 mesh and 7 ¦m floated well and the performance of the zinc flotation circuit was mainly limited by the relatively poor flotation of the very fine zinc values. Approximately 60 per cent of the zinc lost to the final tails lay within the -7 ¦m fraction. The overall flotation conditions were conducive to very good selective flotation of the major proportion of the values and limitations in metallurgical performance were mainly due to the properties of the ultra-fines.

Jan 1, 1971

By Restarick C. J & Stewart P S B, Kelsall D. P

Over a four-hour period of steady plant operation samples were taken at regular intervals from points within the grinding and flotation circuits. Size fractions of each composite sample were analysed for lead and zinc values and a comparison made of the behaviour of the lead, zinc and gangue minerals, size by size throughout the whole circuit. Analysis of the breakage behaviour using dynamic mathematical models gave the rates of breakage of each size fraction of each main component. Simulated grinding experiments showed that the main grinding circuit had sane reserve capacity. In the lead flotation circuit all lead values between 150 mesh (Tyler) and 5 microns had excellent flotation characteristics, and a major proportion had a high rate of flotation which was practically the same for all sizes. Increase in overall lead recovery would require improvement of the flotation behaviour of ultra-fine lead minerals. These were slow floating and were responsible for approximately half the lead losses in the final zinc concentrate and one third of the lead losses in the final tails.

Jan 1, 1980

By E. B. Kroeger, Y. P. Chugh

The goal of this project is to develop, demonstrate, and document the beneficial use applications of a ponded F-fly ash as a road subbase material for the 2.1-mile Meredosia Industry Access Truck Route in Meredosia, Illinois. Approximately 60,000 to 70,000 cubic yards of ponded fly ash are proposed for use on this project without negative environmental impacts to surface water or groundwater. The County Highway Truck Route will consist of a 24-foot wide road built on a 0 to 7-foot thick compacted F-fly ash subbase. Laboratory testing indicates this fly ash will serve adequately as a road subbase, conforming to IDOT standard specifications. The economic considerations of using the Meredosia F-fly ash will also be developed so that a detailed cost-benefit analysis can be prepared for this project and for future projects. This project represents a two-year cooperative development and demonstration effort among the Office of Coal Development and Marketing (OCDM) of the Illinois Department of Commerce and Community Affairs (IDCCA), Southern Illinois University (SIU), Morgan County Highway Department (MCHD), Illinois Department of Transportation (IDOT), AmerenCIPS, and the Morgan County Regional Planning Commission. It is anticipated that monitoring activities will continue for a period of three (3) years after the completion of this project. The MCHD and IDOT will oversee all construction activities and long-term performance evaluation studies. Successful demonstration of large-volume beneficial use applications of F-fly ash at this site will significantly reduce management costs for power plants burning Illinois Coal. Furthermore, it will encourage similar utilization strategies at other sites in the State of Illinois.

Jan 1, 2002

By Frank Alfred Fahrenwald

Discussion of the paper of FRANK ALFRED FAHRENWALD, presented at the New York meeting, February, 1916, and printed in Bulletin No. 109, January, 1916, pp. 103 to 149. F. A. FAHRENWALD, Cleveland, Ohio (communication to the Secretary*).-Since the publication of my paper in the January Bulletin, (which was largely a metallographic treatise), I have been questioned regarding two points referred to therein. One of these is that which deals with the application I have made, p. 119, of the equation for melting pressures which correspond with different working temperatures. The other refers to the statement, p. 137, that "Prolonged heating at relatively low temperatures gave fewer and larger crystals and crystals of different sizes, while a flashing at higher temperatures gave a very fine and uniform crystalline structure, which was much' to be preferred." Especial emphasis was not placed upon either of these two factors, for each seemed perfectly logical and obvious. As they do not seem to be self-explanatory, I will supplement with those portions of my notes which were purposely omitted from the manuscript submitted for publication. A few practical illustrations may serve as evidence in support of the first of these, but it must be understood that in this work the "amorphous theory" is considered as being sound, and that it is assumed that metals allow of distortion, without fracture, by virtue of the formation of slip surfaces, accompanied by the transformation of crystalline material to the, amorphous phase. Effect of Pressure.-In all forging, rolling, and drawing operations, it is known that specimens of small cross-section may be worked at a lower temperature than can be used for the same material in much greater mass and sectional area. In -the larger pieces the maximum pressure is brought to bear upon the material near the surface, so that the interior is not subjected to great pressure, but to, a stress more nearly tensile, or shearing, so only the surface is subjected to the critical melting pressure. In the case of wires which draw hollow, the center is subjected to practically a tensile stress which breaks it, while the surface skin draws perfectly, due to the enormous "flowing" pressure exerted upon it by the surface of the draw-plate.

Jan 5, 1916

By Frank Fahrenwald

I. INTRODUCTORY METALLURGICAL research has discovered many an alloy possessing properties not combined in any single metal, and progress still consists chiefly in the investigation and utilization of alloys. In the case of iron, the demands of automobiles, high-speed machines and high-duty engines have led to the production of special iron alloys which will meet any reasonable specifications in that field. In like manner, the bronzes, brasses and other alloys of copper have been brought to remarkable perfection, and for nearly every industrial purpose some alloy has been found more suitable than the pure metal. Less complete success has attended the attempt to find substitutes for gold, platinum, and the other precious metals. Indeed, it is not likely that a material can be produced which will possess all the properties of any one of them; yet it is reasonable to hope that, for any given use, the properties required may, be found in some less expensive material. Thus, in incandescent electric lamps, the wire passing through the thick glass neck of the bulb was, until recently, almost universally made of platinum, for the single reason that no other known material, suitable as a conductor, had the same coefficient of expansion as glass. But a comparatively recent investigation of the iron-nickel series' has shown that alloys of those metals may be produced, the coefficient of expansion of which can be accurately controlled between that of iron or nickel and zero. Thus, in that particular industry, a substitute for platinum has been found. According to statistical reports, not only considerable quantities of gold and iridium, but also more than one-third of the annual supply of platinum, are used (and, in the nature of the case, irrevocably lost) by dentists. Platinum is thus employed in several forms. As a thin foil, it serves various purposes for which its high melting point, pliability, chemical resistance, and other properties-including the ease with which

Jan 1, 1916

By Andrea Brickey, RICHARD AMOAKO, Akshay Chowdu

Production forecasts derived from the medium-term schedule represent the best path forward for underground mining operations to achieve corporate and operational goals. Unforeseen circumstances, such as equipment breakdown, can cause significant deviations from established production forecasts in the short term. Such situations require timely mitigation of the effects of the deviations in order to stay as close as possible to the medium-term plan. This paper presents a deterministic mathematical formulation for short-term scheduling that addresses this challenge. The formulation is able to make up for deficits resulting from operational disruptions by minimizing deviations from medium-term production goals and medium-term activity start dates. We demonstrate this in a case study by simulating disruptions involving reduction in ore extraction capacity and development advance rate. Aside from the rescheduling capability, this formulation can help mine planners conduct analysis on the impact of various disruptions on the schedule. The formulation can help identify those conditions or disruptions that are more detrimental to the achievement of forecast targets, or otherwise. The formulation also affords mine planners the flexibility to prioritize one production goal over the other, depending on operational conditions at the mine. In the future, we seek to incorporate in the formulation respirable dust, diesel particulate matter and ventilation constraints in order to create more realistic schedules, and enhance miners’ health and safety.

Jan 1, 2024

Provide a lighter, smaller apparatus for more gently supporting electrical cable as it is raised or lowered in a well as compared with the conventional method of using a winch and pulley. Approach The conventional method of running cable into a well is to use a winch to pull the cable over a pulley located at the end of a boom placed over the well. This has the disadvantages of being bulky and of placing a concentrated strain on the cable at the point where it moves over the pulley. These disadvantages are overcome by using a "Chinese finger" cable grip assembly to hold and release a multiple conductor cable.

Jan 1, 1986

By P. BOURY

THIS account of a contrivance which has been found serviceable in practice may be of interest to engineers, and' especially to those engaged in hydraulic mining. In that process, one feature which seems at first sight to possess little significance, is highly important in its effects, namely, the regular supply of water to the " giants." The chief condition of this regularity is an even flow in the pipe-line from the penstock to the nozzle. This, of course, requires that the penstock be kept full. Any considerable surplus of water, overflowing at the penstock, is a simple waste, unless it be otherwise utilized in the sluices. At all events, it does not affect the delivery of the nozzles. But a deficiency at the penstock may admit air into the pipe; and this may produce hydraulic recoil, injuring the line by incessant vibrations, giving rise to leaks, and even to blow-outs, and (when a partial vacuum exists at the time of the fracture the collapse of the pipe. An accident of this sort in our main pipe-line, occasioned partly by a settling of the ground and partly by the presence of air in the pipe, led to the employment of the device here described. The line referred to is made of 30-in. pipe, successively reduced to 18 and 15 in. in diameter, for the supply of two giants. By reason of the causes above mentioned, the 30-in. pipe burst more than 1,400 ft. from the penstock, and, despite the air-valve, the 30-in. pipe was collapsed to such a degree that one length of it, next to the penstock, was squeezed together and positively swallowed by the main pipe, through which it traveled for 750 ft., piercing through a short elbow on the way. This remarkable result was undoubtedly the effect of the vacuum suddenly produced when the pipe burst.

Sep 1, 1906

By Ye Chen, Jianhua Chen, Xianhao Long, Qingxia Liu, Zhenghe Xu

"It is crucial to understand the mechanism of the collector interacting with the mineral surface in the presence of water molecules, which could influence the relaxation and electronic properties of sulphide mineral surface due to the proximity effect for narrow band gap of semiconductors. The adsorptions of three typical collector molecules (xanthate, dithiocarbamate and dithiophosphate) on the sulphide mineral surfaces in the absence and presence of water molecule have been simulated by density-functional theory (DFT). The calculated results show that the adsorptions of collectors on clean mineral surface in vacuum are not in agreement with the observed flotation behaviours. The presence of water molecules has a great influence on the adsorption of collectors. The analysis of density of states of the mineral surface atom suggests that the adsorption of water molecules could influence the electronic properties of mineral surface and consequently influence the adsorption between the surface and the collector molecule.INTRODUCTIONIn the separation of multi-metal sulphide ores, the selectivity of a collector is a key factor for the efficient recovery of the aimed mineral. Xanthate, dithiocarbamate (DTC) and dithiophosphate (DTP) are the most common collectors used in the flotation of sulfide minerals. Generally, xanthate exhibits powerful collecting property but lack of selectivity. While dithiophosphate and dithiocarbamate show the good selectivity in the lead and copper sulphide mineral flotation. The mechanisms of these collectors interacting with the sulphide mineral had been attracted many attentions and several mechanism based on experimental results had been reported (Chander & Fuerstenau, 1974; Fuerstenau, 1990; Raju & Forsling, 1991; Crozier, 1991; Bradshaw, Cruywagen & O’Connor, 1995; Guler, Hicyilmaz, Gokagac & Emekci, 2006). However, the micro-mechanisms of the selectivity of these three thiol collectors on different sulphide mineral surfaces are not fully understood."

Jan 1, 2016