Search Documents

By M. A. T. Cocquerel, M. G. Burcher, J. G. Eacott

"This paper is based on work carried out to examine the feasibility of increasing the smelting rate of two oil-fired calcine-charged reverberatory furnaces . Various constraints prevented physical enlargement of the furnaces and so allention turned to the use of preheated combustion air or oxygen enrichment to bring about the required increase in production. As a basis for further calculation, a furnace heat balance is determined using the smelting metallurgy and combustion data for the current operation. Various other operational data are tabulated and compared with similar data from other operating copper smelters.New heat balances are derived for various levels of combustion air preheat at the current smelting rate, and the effects of air preheat on oil consumption, combustion air and waste gas volumes are tabulated. These data are used to demonstrate the level of increased throughput which would be obtained before constraints in existing gas handling equipment are encountered.A similar exercise for oxygen enrichment is set out, with oil consumption, combustion air and waste gas volumes at various enrichment levels tabulated for the current smelting rate. These data are in turn used to demon strate the smelting rate which would be achieved at a practical level of enrichment before waste heat boiler and gas handling constraints are encountered.The energy implications for both cases are summarized."

Jan 1, 1980

By Nevolina VG, Zakharova IB

The results of a study on the flotation of baddeleyite and associate minerals are presented, together with effective flotation reagents. Detailed microcrystallomorphological analysis of the benefication products were made to find out the features of distribution of different baddeleyite generations between froth and chamber products. To reveal the dynamics of interaction of technological properties of minerals with their morphology and constitution, a method of onthogenetic analysis was used. It is well known that the difference between technological properties of the particles of the same mineral depend greatly on its genesis, but also the relation is direct - by means of constitution (habit). Thus, flotation behaviour of minerals depends on morphology microinclusions, distribution of impurities, dislocations and physical properties of individual particles. The microrelief of baddeleyite grains and crystals from froth and chamber products was studied with an electron scanning microscope. Chemical composition was determined by means of laser, microprobe and chemical analyses. The difference between baddeleyite generations, their distribution in benefication products, and the effects of grain sizes, number of inclusions and chemical compositions were valuated. Conclusions on baddeleyite flotation properties were made. Mineralogical study on eudialite grains from rough ore and eudialite concentrate was carried out. The interrelation between eudialite and associate minerals and negative effect of aegirine on technological properties of eudialite were revealed as well.

Jan 1, 1993

By K. E. H. K. Ishak, S. R. M. Zan

Cement production requires significant energy, and entails high costs and CO2 emissions. This is because the clinker requires very fine grinding. Grinding aids can improve production and fineness and decrease energy consumption by reducing the agglomeration of particles and protecting the balls and liners in the mill. In this study we compare the effects of three different grinding aids on clinker grinding using a ball mill. A commercial grinding additive, triethanolamine (TEA), and two industrial grinding aids (GAA079 and GAA088) were compared by ball milling tests, with additions of 0.05, 0.25, 0.50 and 1.00 wt%. The industrial grinding aids were characterized using gas chromatography-mass spectrometry (GC-MS). Particle size and morphological analyses were performed using SEM and XRD. The best results were obtained with 0.25% GAA088, which has a higher active component of diethanolamine isopropanolamine (DEIPA) than TEA. The unique combination of TEA and DEIPA in GAA088 enhances grinding efficiency and significantly improves the particle size distribution compared to TEA alone.. The grinding aids produced smooth rounded particles, which have a smaller specific surface area, enhancing the quality of the cement. XRD showed no significant structural distortion with or without grinding aids, and it was also found that the grinding aids helped decrease ball coating during grinding. The use of grinding aids can significantly improve clinker production and fineness while decreasing energy consumption, which can help reduce the costs and CO2 emissions associated with cement production.

Sep 6, 2023

By E. J. Duggan

In the course of the grinding experiments conducted at Climax over the past twenty years one interesting phenomenon was discovered. This was that balls made of certain types of steel grind more ore than some others. The most significant variation was found in the results secured with a hard alloyed forged bail compared with the forged carbon ball supplied by most ball manufacturers These findings were confirmed in many repeated controlled tests. The value of these tests depends on the methods used, the facilities available and the care with which the investigations were conducted. These are described in the following. This testing has largely been done in eight 91 x 81 low discharge ball mills in closed circuit with 7811 duplex screw classifiers. The mills run at 20 RPM on a feed approximately minus 3/8 inch. The ore is ground through 28 - 35 mesh in one stage. Each mill and auxiliary classifier is in a separate, parallel grinding and flotation section The, ore to each: section is the same in every particular and is fed to each mill bin from a common conveyor tripper. The ore from the bin to the ball mill is weighed on a conveyor scale. The power input to each mill motor is determined with a watt hour meter which measures the power to the mill motor only. Both the scales and meters are checked periodically by standard methods and have been found to give consistent readings. Automatic samplers are employed on each section to obtain accurate measurement of the size reduction. A size analysis of the classifier overflow is made each shift and a composite size analysis is obtained from a weighted average of the various shift analyses. The mills are driven by 450 horsepower synchronous motors so that there is no speed variation and shell liner age is kept as nearly the same as possible in mills under test. The same set of operators is assigned to a mill under test as to the control mill. In all other particulars such as ball load, mill density, liner design, etc., the mills are operated in precisely the same manner. This is an ideal arrangement for plant testing. From observations of ball mill performance over the past twenty years, it is the opinion of the operating staff that variations of as little as one to two percent in mill capacities may be determined if sufficient operating hours are devoted, to a test. Relations between mill capacities, fineness of grinds and power consumptions have been established with a high degree of accuracy. In Table I are given the figures for one test. These show that while the grind with the hard ball was slightly coarser, the tons ground per hour was 5.4 percent greater with the soft ball, and 6.1 percent greater on the basis of minus 100 mesh produced. The power consumed per ton with the hard ball was 4.4 percent greater on a tons per hour basis. The soft ball was inferior in wearing qualities and steel consumption per ton of ore was 24 percent greater with it. In this test the mills were charged with the two different balls for a period of three months to allow the ball loads to come to equilibrium. In Table II are given the specifications of the two balls. The difference in grinding rates may be accounted for by the nature of the ball surfaces. The surfaces of the soft balls after being worn a while are rougher to the touch. Enlarged photographs of the worn-in surfaces of hard and soft balls are shown in Figure I. These show the presence of scratches or skid marks on the hard ball surface which indicates less nipping effect. The Climax ore pulp has a pH of 6.0 and is in a dispersed state. The viscosity is low compared with most ores especially those that are conditioned with lime. This would lower the tendency of the pulp to adhere to the balls with a lower grinding efficiency as a result. It was also thought that the relative rates of wear from surface to center might affect the make-up of an equilibrium ball charge. This probably has little effect on capacity as shown by the size analyses of the two ball charges in Table III. This hypothesis was subsequently investigated by the use of rationed charges. The rationed charge did not overcome the advantage in

Jan 1, 1958

By C. R. Ince

THE term "differential flotation" is used to denote a flotation operation in which separation is effected between two or more minerals of the same class; e. g., lead sulfide from zinc sulfide, pyrite from blende, chalcopyrite from pyrite, chalcopyrite from blende. At present, so far as published work shows, there seem to be two theories as to the mechanics of differential flotation. The earlier and more generally accepted theory is that the so-called depressing agents alter the surface of one or more of the sulfides in the ore, either by chemical action or adsorption, so that it is no longer amenable to flotation, but that these depressed sulfides can be revived, after the unaffected sulfide has been floated, by reagents which react chemically with the altered surface and make it amenable to flotation. More recently, Professor Taggart1 has advanced the theory that slime adsorption is an important factor in differential flotation. He believes that, with the proper use of a class of agents, which he calls .dispersion agents and which include practically all the depressing agents, one can cause the slime to adsorb differentially on sulfide surfaces. A gangue-slime coated sulfide surface will act as a gangue particle and will not float. If, subsequently, an agent that will remove the gangue-slime coating is added, the sulfide again assumes its original surface and can be floated as an ordinary sulfide. This-is the basis of the slime theory of differential flotation. Timber Butte mill at Butte, Mont., is a typical lead-zinc flotation concentrator. Neihart ore, chosen for investigation in this work, is one of the custom ores treated at that mill. Practice at Timber Butte mill in February, 1928, was as follows: A combined lead-zinc concentrate was first made using 0.2 lb. per ton on the ore of potassium xanthate and 0.03 lb. per ton of Cleveland Cliffs oil after 1.5 lb. per ton of lime and 1 lb. per ton of calcium chloride has been added just before the ball mill. The concentrate was then thickened to 70 per cent. solids. Potassium cyanide to the amount of 0.3 lb. per ton and zinc sulfate in the quantity of 0.5 lb. per ton were added to the thickened pulp and the whole

Jan 1, 1929

By Deren Zhu

Based on the results of in-situ observations and physical model analysis, a computer simulation method, FEAEBP, has been developed to predict the behaviors of main roof breakage in longwall mining by considering it as a Kirchhoff plate on Winkler elastic foundation. This method in used to investigate the initiation, and development of the breaking process of main roof and its displacement field before and after its breakage. In this paper the simulation method is introduced, characteristics of the displacement field of the main roof is discussed and monitoring variation of the displacement field of the main roof in a Chinese longwall face is demonstrated.

Jan 1, 1989

By M. P. Brungs, S. Haji Amini

Static dissolution of CaO into a CaO-SiO2-Al2O3slag and slags with additional fluxing agents (fluorspar, nepheline syenite and ilmenite) was studied. The slag was packed into dense CaO crucibles and heated to 1500ºC /1600ºC. After reaction, the crucible was air cooled and cross-sectioned. The development of the Ca2SiO4 phase and concentration profiles of various cations across the reaction zone were examined by Electron Probe Micro Analysis. At 1500ºC, a Ca2SiO4layer was found to form at the CaO/slag interface. No such layer was evident at 1600ºC. Ilmenite and nepheline syenite were found to be effective substitutes for fluorspar, increasing the rate of CaO dissolution.

Jan 1, 2004

By Gerald Greene

Tan various lead producers have given the subject of lead drosses much attention in recent years but the problem of their economical treatment is yet to be solved. Formerly the copper in the furnace feed was removed from the furnace in the form of matte. The speiss at that time consisted principally of the iron arsenide. The practice today is to roast off most of the sulfur and the copper in the feed forms a dross in the furnace, which is removed from the furnace with the lead. This material is poured into the drossing kettles and allowed to cool down to but slightly above the freezing point of lead. The copper dross, containing almost all of the arsenic and part of the antimony, is skimmed off and treated in a small reverberatory furnace at most plants. This is essentially a liquation process. The skimmed dross contains from 70 to 80 per cent lead, and much of this lead is liquated out. The products from this treatment are: (1) impure lead, (2) speiss and (3) matte. The speiss from the reverberatory furnace was studied in this research. The literature on the subject is of very little assistance, as almost no work has been done on the problem of establishing the exact identity of the various phases present. One author(1) states that speiss consists of a series of isomorphous compounds of the general formula FexAsy in which the Fe may be replaced by Ni, Co, Cu, Pb, Ag, Au, Pt, Zn, Cd and the As replaced by Sb, S and Bi. Hofman(2) states that the iron arsenide present is Fe5As.

Jan 1, 1935

By E. Ghali, A. D. Bas

There is a lack of electrochemical studies of oxidized gold ores since the majority of previous studies were conducted with sulphidic gold ores. In this study, the influence of agitation and iron oxide minerals, i.e. magnetite, hematite, and maghemite on gold leaching was investigated by means of galvanic and passivation phenomena. Cyclic voltammetry studies of Roasted Gold Ore (RGO) in de-aerated electrolyte have shown one oxidation and one reduction reaction while three oxidation and one reduction peaks were observed with gold electrode. Galvanic coupling results by Zero Resistance Ammeter (ZRA) mode indicated that magnetite showed a negative effect on gold dissolution while maghemite and hematite showed a positive effect, relatively, as a result of higher galvanic corrosion rates. Generally, gold dissolution was found to increase in the initial 15 minutes. Increasing agitation speed from 100 to 400 rpm resulted in higher galvanic corrosion rates for RGO, magnetite, and maghemite electrodes, while 250 rpm was found to be optimum for hematite electrode. Passive products such as silver and iron-oxide were identified by XPS and SEM-EDS analysis, respectively.

Jan 1, 2015

By Ofori-Ansah K

The zeta potential on the surface of activated orit carbon were estimated in lhe presence of selected cations and anions that are normally associated with gold bearing ores in Kalgoorlie area of Western Australia. Additions of such ions to solution of varying pH shifted the isoelectric point of carbon from pH 4.45 to pH 7-8.3, while the anions moved Lhc isoelectric point 10 less than pH 3.2. In the presence of gold cyanide SoluLion additions of spectator ions indicated the isoelecLric poilll to be aL pH less than 3.2; the only exception was for Fe" ion where the isoelecLric point was at pH 5.9. The decrease in zeta potential appeared to be related to the counter-ions present. The decrease may also be related to the adsorption of hydroxyl ion complexes that are likely to be formed when cations are present in the solutions.Gold adsorpLion by activated orit carbon from gold cyanide solution seem to be indicated by the magnitude of zeta potential on the carbon surface. An attempt is made to relate gold adsorption and zeta potential on carbon surface with the pH of the medium.

Jan 1, 1984

A Study of Extracting Vanadium from Stone Coal Using Cyclic Oxidation

Sep 13, 2010

By Thom Mambe, Angelo Fernando

The objective of this work was to identify key parameters related to the reduction of the sulphur content in ammonium diuranate (ADU), and the identification of solid products being formed under various operating conditions. A laboratory-scale, continuous ADU precipitation circuit was assembled using a glass reactor vessel immersed in a temperature-controlled water bath. A pre-prepared uranium feed solution was fed continuously using a peristaltic pump. Anhydrous ammonia mixed with compressed air was metered and pumped using a double-headed peristaltic pump. An over-head mixer was used to keep the solids in suspension. The precipitated ADU slurry was removed from the reactor at the same flow rate as the feed solution. The slurry was sampled to generate ADU solids for chemical and physical analysis after four hours of continuous operation to ensure steady-state conditions. The following variables were studied to determine their influence on the sulphur content in the resulting ADU. (a) sulphate:uranium molar ratio in the reactor (1:1, 1:5, 1:10 and 1:20) (b) precipitation pH ( pH 6, 6.5, 6.9, 7.5 and 9) and (c) precipitation temperature (40C and 60C) A total of 18 tests covering the above parameters were conducted, and the results indicated that the sulphur content in the resulting solids was highly dependent on the reaction pH. Out of the pH levels tested, tests completed at pH 6.9 and 7.5 generated solids containing the lowest sulphur contents, between 0.5 to 1.5% S uranium basis (UB). The sulphur content in solids was found to vary linearly with the sulphate:uranium ratio in the feed solution, showing a statistically valid correlation. The impact of temperature was minor between 40°C and 60°C, with a slight advantage at higher temperatures. Tests at a sulphate:uranium ratio of 1:1 produced solids with the lowest sulphur contents. The influence of pH or temperature on sulphur content in solids was almost non-existent at this sulphate:uranium ratio. Precipitation pH is the major factor influencing ADU sulphur content, followed by the uranium to sulphate ratio.

Jan 1, 2020

By C. H. Mahoney, P. E. LeGrand, A. L. Tarr

MAGNESIUM, it is now generally realized, differs in some important aspects from most other structural metals, not excepting even its close neighbors, the aluminum-base alloys. This is particularly true with respect to the effects of elevated temperatures on the two light metals when in the molten state. Aluminum, on the one hand, should not be raised above its melting point any higher than is absolutely necessary if one is to avoid danger of gas absorption and a tendency toward grain growth in the resultant casting.1 Magnesium alloys, in sharp contrast, actually benefit by being heated to temperatures considerably above their melting point. It is a commonly accepted practice to establish the desired fine grain in the industrial magnesium alloys of the aluminum-bearing group by raising the temperature of the melt after the refining treatment to some 25e C (482°F.) above the melting range. To recall briefly the typical practice for magnesium alloys, the molten metal is refined by fluxing at about 730° C. (1350 F.), and after the melt has been covered with a suitable flux, the temperature is raised to between 870°C. (1600°F.) and 930°C. (I700°F.). It is then cooled as quickly as possible to the casting temperature. This superheating, as it is called, results in a fine-grained cast metal structure which has superior mechanical properties, enhanced amenability to solution heat-treatment, and better machinability than cast metal that has not been superheated. The minimum temperature of superheating varies to some extent with the composition of the alloys to be treated and usually increases with the percentage of magnesium in alloys containing the same constituent metals.2 It should be noted that the grain-refining effect of superheating is markedly apparent only in connection with the alloys containing aluminum as an alloying constituent-the binary alloy containing r.5 per cent manganese, for example, is not refined in grain to any noticeable extent by a superheating effort. While the phenomenon of superheating is well known in the magnesium industry, the mechanism of the process has remained a mystery. During the superheating cycle something occurs that forces a fine grain upon the solidifying metal. The process has been controlled in an empirical manner, and occasionally, especially on large-scale melts, and for no apparent cause, no grain refinement is obtained from a superheating treatment. Only a few papers of importance have been published on the subject. Of these, one of the most helpful is the paper by Achenbach, Nipper and Piwowarski,3 which gives considerable data concerning the effect of superheating on various properties such as fluidity, shrinkage and hot crack formation, as well as grain size, and a discussion without any definite conclusions on the theoretical aspects of superheating. A short article by Murphy, Wells and

Jan 1, 1945

By Leon Lorenzen, Rodrick M. Lamya

"Leaching behaviour of nickel – copper matte in a CuSO4–H2SO4 solution during the repulping stage of a matte pressure leaching process has been studied. The base metal recovery process investigated in this study consists of a matte repulping stage prior to a series of pressure leach stages. The repulping stage is essentially an atmospheric leach stage in which the Ni-Cu matte, containing small amounts of cobalt and iron, is leached in copper spent electrolyte from the tankhouse, resulting in dissolution of the nickel with simultaneous precipitation of almost all the copper.Effects of various process parameters on the kinetics and extent of the leaching reactions, as well as on the cementation of copper from the solution have been quantified. The parameters investigated were temperature, particle size, pulp density, stirring speed, residence time, initial copper concentration and initial acid concentration.Leaching characteristics of the preleached matte during the subsequent pressure leach operation has also been studied. The effects of variations in the conditions in the repulping stage on the kinetics and degree of base metal dissolution during the pressure leach stage have been investigated. Any transformations that occur in the mineral phases of the matte during the leaching process have been studied, and a leaching mechanism proposed."

Jan 1, 2003

By R. M. Lamya

The kinetics of copper cementation during atmosphere leaching of a Ni-Cu matte in CuSO4-H2SO4 solution was studied as a function of initial copper ion concentration, initial acid concentration, temperature, stirring rate, particle size distribution and pulp density. It was found that all these process variables influenced the rate of cementation. A two-stage rate of reaction was observed inmost of the experiments, with the rate of cementation in the initial stage being slower than that of the subsequent second stage. The increased rate of cementation in the second stage was attributed to the enhancing effect of the surface deposit. The cementation process was found to take place by two different rate-controlling mechanisms. At a temperature range of 50?70°C, an activation energy of 74.6 kJ/mol was obtained, indicating a surface reaction controlled process. At higher temperatures (70?80°C) a lower value of activation energy was observed (18.2 kJ/mol), indicative of a process controlled by diffusion through surface layers. The structural characteristics of the cemented deposit could not be determined in the investigated system where the deposit was mixed with the leach solid residue.

Jan 1, 2005

By M. Loan

The Zinifex's Hobart Smelter uses the paragoethite process to remove dissolved Fe(III) from concentrated zinc leach liquors. This produces a residue consisting primarily of 6-line ferrihydrite (a hydrated Fe(III) oxyhydroxide), several insoluble components derived from the calcined zinc concentrate neutralization agent and other precipitated phases, such as jarosite and silica. The precipitation of 6-line ferrihydrite in the paragoethite process was studied using a laboratory-scale continuous crystallizer, and the conditions were selected to limit high levels of dissolved silica and jarosite. This approach allowed the reactor pH and the rate of precipitation to be correlated with residue solid-liquid separation, particle size, morphology, residual zinc and sulfate concentrations, and phase formation (e.g., goethite, jarosite, schwertmannite, and 2- and 6-line ferrihydrite). These studies delineated the mechanism of 6-line ferrihydrite precipitation in the kinetically controlled paragoethite process, and its inter-relationship with goethite and jarosite precipitation under conditions where 6-line ferrihydrite is favoured. Unexpectedly, the generation of a more crystalline goethite precipitate with larger "primary" particle size did not produce a residue of improved properties, as bulk aggregates dictate the physical properties of the residue and not the crystallinity. Furthermore, it is difficult to precipitate 2-line ferrihydrite or schwertmannite under existing paragoethite process conditions.

Jan 1, 2006

By Seneviratne SP

The excessive displacement of the seam floor in headings (i.e. roadways) called 'floor-heave' is often experienced in the underground mines of the Southern Coalfield of New South Wales. Apart from interfering with the mining operations, the phenomenon could be detrimental to the stability of the pillars left for support leading to an unpredictable increase in the subsidence of the overlying strata. The latter could pose a serious problem, particularly in the design of partial extraction layouts of mining for areas where subsidence is to be controlled. The susceptibility of the floor of different rock materials and thicknesses in a given `panel and pillar' partial extraction geometry was examined by two- dimensional Finite Element Modelling of the displacements, stresses and failure zones around the excavations. The modelling, assuming elastic behaviour of the materials, indicated that the maximum vertical displacements of the floor increased substantially as the Young's Modulus of the material decreased to less than 7GPa and the thickness of the layer increased. The results also discount the possibility of a properly designed panel and pillar geometry in the Southern Coalfield of New South Wales being unable to adequately control surface subsidence through the pillar, or its core independently of the yielded ribs, penetrating the floor.

Jan 1, 1992

By D. A. Salinas G., A. H. Castillejos E.

Pachuca tanks are commonly used in the hydrometallurgical industry to carry out leaching operations. The fluidynamic characteristics of the liquid phase, resulting from the injection of gas into the draft tube, are important to achieve the complete suspension of the mineral particles and has a decisive influence in the mass transfer processes occurring in this reactor. This study investigated the effect of different design and operating characteristics on the liquid velocity field. using a laboratory-scale Pachuca tank. The transparent model was filled with water, and air was injected through the bottom in the absence of mineral particles. The liquid velocities over the whole reactor were measured under several experimental conditions using particle image velocimetry (PIV). This technique allowed to obtain a very detailed picture of the liquid motion even in the draft tube, as long as bubbles were absent from the measured field of view. The experiments have shown that the liquid velocities increase with increasing the draft tube to tank diameters ratio, the distance from the conical bottom to the draft tube entrance, or the gas superficial velocity. On the other hand, an increase in the water level with respect to the draft tube outlet caused a decrease. A mathematical model, which used the no-slip model, to calculate the variation of axial effective density along the two-phase region, was found to predict liquid velocity fields which agree very satisfactory with the experimental results obtained under all the conditions studied.

Jan 1, 1999

By Ross W. Smith

Many studies have been made of the microflotation of quartz (1,2,3,4,5,6) and alumina (3,5,6, 7,8) using various anionic and cationic hetero- polar hydrocarbon surfactants as collectors. A few studies have been made on these minerals using amphoteric hydrocarbon collectors ( 9,10, 11,12) and only a few studies have been made on the use of fluorocarbon surfactants as flotation collectors (13,14). The present investigation compares microflotation response of the two minerals in hydocarbon and fluorocarbon collector systems of the anionic, cationic and amphoteric types. An attempt is made to relate flotation response of the minerals to their electrokinetic behavior and the pKa values of the collectors.

Jan 1, 1979

By Qingming Feng, Dongbo An, Jinhong Zhang

The application of the geopolymerization of mine tailings as construction materials is hindered by the fact that conventional geopolymerization of mine tailings usually involves a large consumption of alkali, i.e., sodium hydroxide (NaOH), and a long curing time, because of the relatively low reactivity and the high Si/Al ratio of mine tailings when compared to other active resources such as fly ash and clay minerals. The present study is focused on efficiently activating mine tailings, reducing alkali consumption, decreasing curing time and improving compressive strength. We firstly investigate the temperature effect on the alkali activation of mine tailings during geopolymerization. Secondly, the impact of additives, i.e., calcium hydroxide and aluminium oxide, on the compressive strength of samples is studied. Thirdly, different forming pressures have been applied to remove excessive alkali and its impact on samples' strength has been investigated. The results show that a 40 MPa unconfined compressive strength (UCS) can be achieved with the geopolymerization samples after mine tailings are activated by sodium hydroxide at 170°C for 1 hour with the addition of calcium hydroxide and alkali dissolved aluminium oxide, further compressed with a 10 MPa forming pressure and finally cured at 90°C for 3 days. The findings of the present work provide a novel method for the geopolymerization of mine tailings as construction materials.

Jan 1, 2014