Search Documents

By David Van Aken, Arpana S. Murthy, Simon Lekakh, Von L. Richards

"Three heats of 17-4PH stainless steel: with zero, three percent, and seven percent cobalt addition were melted in a 45kg (1 00lb) induction furnace under argon; and cast into no-bake molds and preheated investment shell molds. Specimens were sealed into quartz tubes under vacuum, and homogenized at 1200°C from 2h to 72h. Computational thermodynamics and optical microscopy were used to predict and characterize the microstructures. The lath martensite packet size and the amount of 8-ferrite were observed to be inversely related. A compromise between decrease in segregation and increase in lath martensite packet size was chosen for the optimum homogenization treatment. The specimens were austenitized, quenched, and characterized for retained austenite using x-ray diffraction. Age hardening kinetics were studied at 454°C (850°F), 468°C (875°F), and 482°C (900°F); and, the activation energies for precipitation of copper were calculated. Tensile properties and Charpy V-notch impact energies were measured in the peak aged condition. Fracture surfaces were observed using scanning electron microscopy and Energy Dispersive Spectroscopy. The addition of cobalt was found to be beneficial for the improvement of strength as well as notch toughness.IntroductionSegregation in the as-cast condition is one of the drawbacks of metal casting. This paper presents a study on the homogenization treatment of 17-4 PH cast stainless steel and the effect of cobalt addition on tensile properties and Charpy V-notch toughness. Lattice dilatation studies show that additions of up to 6% Co to iron has a negligible effect on the lattice parameter, whereas both the modulus of elasticity and shear modulus increase with increasing cobalt additions5• An ordering reaction has been reported in cobalt-containing, maraging steels and contributes to the hardening during ageing1-4• Although, cobalt addition in maraging steels has been extensively researched, and has been reported to be beneficial; it has not been explored much in other age-hardening stainless steel systems. In a previous study, the addition of 3% Co in cast 17-4 PH martensitic age-hardenable steel was found to improve the strength and elongation while maintaining the charpy V-notch toughness6."

Jan 1, 2011

By Lloyd R. Nelson

Experimental results of three-phase mixing in a physical model of a CCRL for metals refining are presented. The system was operated above a critical lower liquid height-to- width ratio (H,/W) of unity, with adequate bottom gas injection through a line of central, single tuyeres (Q,/A = 7.5 cm/min, or c = 17 W/m3) to sustain levels of interphase transport considered appropriate to an industrial pyrometallurgical refining operation. The application of a thermal tracer technique to elucidate both longitudinal mixing and interphase heat transfer is discussed. The results indicate that even under conditions of significant bottom gas injection, it should be possible to maintain acceptably low longitudinal mixing 1 (D, < 20 cm /s and D,/uL < 0.1) in the CCRL. Interphase mass transfer coefficients of the order of 0.004 cm/s are predicted from the measured interphase heat transfer coefficients (h = 1.3 to 2.0 kW/m2K), using the heat and mass transfer analogy. Adequate rates of rehning are predicted for an industrial CCRL operated under such conditions.

Jan 1, 1995

By J. W. Matousek

Cobalt behavior in pyrometallurgical processes is traditionally analyzed using slaglmatte distribution coefficients as functions of matte grades or matte iron contents. L(s/m) = (%Co) I [%Co] = f [%CuNi] or f [%Fe] The method is inconvenient to use in predictive mass balance work because of the interdependence of assays and mass quantities. An alternative procedure is proposed based on cobaltliron ratios for slags and mattes: Js = (%Co) / (%Fe), Jm = [%Co] / [%Fe], and J, = b + m [Jm]

Jan 1, 1993

By Lijun Lu, Honghui Fang

This article carried out the experimental study on using desulfurization ash in steel slag composite material. This was done by investigating the desulfurization ash content in formula one and formula two samples on the influence of setting time and strength of mortar. Through this study the following conclusions were reached for formula one: (1) a setting time of more than 10 hours is required, (2) a dosage of desulfurization ash of 1 ~ 2% is optimal, where flexural strength is reduced by 10% ~ 23% and compressive strength reduced by 5.7% ~ 16.4%. The conclusions of formula two were: (1) when the dosage of desulfurization ash is within 5%, the setting time is within 10 hours; (2) when the dosage of desulfurization ash is 1 ~ 2%, the flexural strength is increased by 5 ~ 7% and the compressive strength is reduced by 1 ~ 2%. The results show that the formula two is better.

Jan 1, 2015

By Sen-xiang Yang, Xin-teng Liang, Gui-jun Li, Jian-hua Zeng, Yong Chen

"This research is based on PANSTEEL 120t steelmaking converter technology to have the quantitative description of the time needed in uniform mixing of molten steel in the converter with the computer. In present work, the numerical simulation approach is used to analyze oxygen lance nozzle, the flow condition of oxygen and flow status of molten steel in the converter. The various oxygen jet flows that come out from different angles and the flow status of all kinds of jet flows in the converter have also been simulated. All of the simulation parameters are based on the specifically practical conditions according to the physical conditions of PANSTEEL 120 t steelmaking converter. Through numerical simulation, the angle parameter of the oxygen lance nozzle is 16 °. The optimized oxygen lance 536-16 has a good performance in industrial application. This kind of phenomenon shows that the ways and processes of numerical simulation in this research are right.IntroductionThe oxygen lance system is the significant process in semi-steel making converter. It's related to whether the converter or even the whole system can function well. While in actual production, many problems emerge in the process of using the former oxygen lance, such as re-drying, slopping, high lance position, dead burning and even blowing out. In continuous fast-paced process, the unstableness of oxygen lance will lead to speed droop or even stop pouring. Analysis shows that all these problems are not only related to the raw materials but also the design of oxygen lance. Bad oxygen lance's scorification kinetics condition and low content of FeOn in early slag are the direct factors that we cannot easily control in steelmaking at present [l]. Therefore, the good scorification kinetics condition which is related to nozzle has good influence on BOF steel making."

Jan 1, 2013

By J. A. Bakken

Thermal plasmas are interesting for a wide range of metallurgical and chemical processing applications. The 300 kW experimental reactor PRESS, which has been in use since 1987, is operated in the transferred arc mode with three or one plasma torches . Tests include remelting of silicon fines and production of ultrafine silica. Work on a novel three stage process for production of silicon metal is under way. A 1:1 model of the plasma reactor is used to measure the wall heat flux distribution calorimetrically. The cold walls of this model are divided into several water-cooled sections. The same plasma torches as in the real hot-wall reactor are used. In parallel to the experiments and calorimetric measurements theoretical work is done on numerical modelling of one and three transferred arcs. A modified version of the flow simulation program FLUENT from Creare Ltd. is used.

Jan 1, 1991

By V. I. Lakshmanan, R. Roy

Base metals and PGMs are currently recovered from sulfide concentrates using pyrometallurgical processes. These processes suffer from several limitations such as being capital intensive, scaling problems, S02 emissions and long delay in value recognition. Alternative hydrometallurgical technologies have so far not been successful and currently total pressure oxidation and partial pressure oxidation hydrometallurgical technologies are being evaluated. Process Research ORTECH has developed a unique hydrometallurgical process to recover base metals and precious metals using mixed chloride technology. In a first stage leach, base metals are recovered and elemental sulfur is liberated from hydrogen sulfide formed during this leaching stage. During second stage leach, precious metals are recovered using proven separation technologies. Some of the advantages of the process are the recovery of elemental sulfur from sulfide sulfur, recycle of the chloride lixiviant thereby eliminating effluent treatment steps and use of excess energy from the Claus reactor for the pyrohydrolysis step.

Jan 1, 2011

By Priscilla Aki Mori de Hanashiro, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Hugo Hashimoto

"The LCDs are used in televisions, calculators, mobile phones, computers (laptops and tablets), video games and other electronic devices. The advancements in technology make obsolete these devices, causing excessive disposal of LCDs and therefore decreasing life span of landfills. In this context, the LCDs from LED LCD TVs arise as an additional source of waste electrical and electronic equipment (WEEE). Thus, it is essential to develop LCDs recycling methods, beginning with the LCD characterization followed by displays processing, aiming the materials separation and using some Ore Treatment Techniques, and finally, the recovery of indium using acid leaching. The analysis methods that will be used in this work are: Fourier Transform Infrared (FT-IR) and Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES).IntroductionLiquid Crystal Display (LCD) technology is applied in modem televisions, calculators, mobile phones, computers and a wide range of electronic devices. It has replaced Cathode Ray Tube (CRT) technology as the most advantageous display product, due to lower electrical power consumption, size and weight reduction, and no radiation emission [ 1]. The constant improving of LCD screen technology reflects on its growing contribution to the amount of waste electrical and electronic equipment (WEEE): an estimated 50 million tons of WEEE are produced every year [2]. Once the most common method of its disposal are landfills, the LCD technology therefore became an environment issue [3].LCD structure is composed by components made by different materials. In order to develop a LCD recycling methodology that gives the right destination to these materials, a previous characterization stage is required. This characterization includes a disassembly process and material identification analysis. One of the LCD components is the screen, which is composed by polymeric and glass layers. The liquid crystal glass was the starting material of this study. It contains indium in the form of indium tin oxide (ITO) film. This ITO film is deposited in the glass by a sputtering process and acts as the electrode material [4,5]. It has in its composition 90% ofln203 and 10% ofSn02 [6]."

Jan 1, 2014

By Larry G. Twidwell, Jannette L. Chorney, Bryce D. Ruffier, Katelyn M. Lyons, Daniel W. Gaede, Ryan J. Foy, Jerome P. Downey

The Metallurgical and Materials Engineering Department at Montana Tech is investigating various methods of extracting and refining rare earth elements from mineral ores and concentrates. As part of this research, an elevated temperature “roasting” process has been evaluated as a means of converting the rare earth elements contained in various matrices to bromides as a pretreatment step in preparation for downstream rare earth element extraction and recovery operations. Laboratory and bench-scale experiments have been performed to assess the effects of varying temperature (150 to 400° C), time (1 to 4 h), and the ammonium bromide to rare earth oxide molar ratio (6 to 24) in the roaster charge. The results show that nearly complete bromination of the rare earth oxide is achievable when the roast is performed under optimum conditions.

Jan 1, 2015

By H. Kohno

The Onahama No.3 tankhouse started commercial operation in early 1973, with the capacity of 8,500 metric tons per month. When the No.3 tankhouse was constructed, the starter sheet stripping section was rebuilt at the No.2 tankhouse and electrolyte purification section was expanded. The previous AIME paper in 1976 described the design principles of the No.3 tankhouse and its layout, This paper describes the starter sheet stripping machine in the No.2 tankhouse and the electrodes handling system in the No.3 tankhouse and all these equipments were developed for the operation of the No.3 tankhouse. A Hazelette continuous casting machine was also introduced in order to cast thin anodes with accurate shape. Owing to the adoption of thin anodes, gold, silver and copper inventory is reduced by 40%. Jumbo tanks and newly developed mechanical equipments were adopted and no work on cells during pulling up operation was achieved. Using thin anodes with accurate shape, inspection work was completely abolished while maintaining high current efficiency and high cathode quality. Labor cost was reduced by 70% and only six operaters can produce? 8,500 metric tons of cathodes per month. The same new electrolysis process is appreciated and has been used as a newly built independent tankhouse by Kidd Creek Mines Ltd., in Canada in 1981 with excellent results

Jan 1, 1987

By Junmo Ahn

This study investigated leaching kinetics by alternative lixiviants for copper leaching from chalcopyrite (CuFeS2), the most abundant copper resource in the world. As a refractory sulfide mineral, chalcopyrite shows low copper extraction due to passivation on chalcopyrite surface. Also, decrease of copper grade with high portion chalcopyrite requires the alternative leaching procedure to increase copper recovery. Therefore, alternative lixiviants such as sulfurous acid and methanesulfonic acid (MSA) were tested for both concentrate and low grade ore to enhance copper extraction. Also, an oxidant, hydrogen peroxide, was compared to ferric to find out the improvement of leaching kinetic. In concentrate leaching tests, 30 g/L MSA showed the highest copper extraction (47%), compared to other lixiviants at 75 °C. Periodical H2O2 addition enhanced copper extraction, and above 90% of copper extraction was observed within 96 h by periodical addition of 0.6% H2O2 at 75 °C. The activation energy of chalcopyrite leaching by MSA and H2O2 achieved 40 kJ/mol, which is chemical reaction control. The results of low grade ore leaching tests indicates that no significant difference among lixiviants (H2SO4, H2SO3 and MSA) with ferric was observed, all of which achieved around 37% within 24 h at room temperature. However, significant increase of copper extraction (>80%) was observed at both 20 g/L MSA and 10 g/L H2SO4 conditions by the addition of 10% H2O2.

By D. A. Milligan

Ammonia leaching of copper sulfide concentrates, matte, scrap or other sources of copper yields copper amnine sulfate solutions which are converted to metal in a two-stage process involving precipitation of inter- mediate sulfites and their thermal decomposition to copper powder of high purity. Processing details and results are given. Considerable simplification in circuitry and cost savings are indicated. Energy requirements are reduced by substitution of copper powder precipitation and ammonium sulfate crystallization for solvent extraction, electrowinning and lime boil.

Jan 1, 1976

By Michael I. Morris

The U.S. Department of Energy&apos;s (DOE&apos;s) Transuranic and Mixed Waste Focus Area (TMFA), funded from fiscal year (FY) 1996 though FY 2002, was tasked with finding solutions for the mixed waste treatment problems of the DOE complex. During TMFA&apos;s initial technical baseline development process, three of the top four technology deficiencies identified were the need for amalgamation, stabilization, and separation/removal technologies for the treatment of mercury-contaminated mixed waste. The Mercury Working Group (HgWG), a selected group of representatives from DOE sites with significant mercury waste inventories, assisted TMFA in soliciting, identifying, initiating, and managing efforts to address these areas. Solicitations and contract awards were made to the private sector to demonstrate both the amalgamation and stabilization processes using actual mixed wastes. The goal was to develop separation and removal processes that will address DOE&apos;s needs. This paper discusses the technology selection process, development activities, and the accomplishments of TMF A through these various activities.

Jan 1, 2003

By J. P. Gu, C. Beckermann

"Melt convection and macrosegregation in casting of a large steel ingot is numerically simulated. The simulation is based on a previously developed model for multicomponent steel solidification with melt convection, and involves the solution of fully coupled conservation equations for the transport phenomena in the liquid, mush, and solid. Heat transfer in the mold and insulation materials, as well as the formation of a shrinkage cavity at the top are taken into account. The numerical results show the evolution of the temperature, melt velocity, and species concentration fields during solidification. The predicted variation of the macrosegregation of carbon and sulfur along the vertical centerline is compared with measurements from an industrial steel ingot that was sectioned and analyzed. Although generally good agreement is obtained, the neglect of sedimentation of free equiaxed grains prevents the prediction of the zone of negative macrosegregation observed in the lower part of the ingot. It is also shown that the inclusion of the shrinkage cavity at the top is important in obtaining good agreement between the predictions and measurements.IntroductionMacrosegregation in large steel ingots is one of the most well-known and now classical problems in the field of solidification and casting [1]. Commonly found macrosegregation patterns in steel ingots are a positively segregated zone at the top, negative segregation near the bottom in the equiaxed zone, inverse segregation near the ingot surface, V-segregates along the centerline, and A-segregates in the columnar zone [2, 3]. It is well established that the macroscopic transport of species leading to macrosegregation can occur by a variety of mechanisms, including thermally and solutally driven natural convection of the melt in the mushy zone, flow due to solidification contraction, and the sedimentation of free equiaxed crystals. Fredriksson and coworkers [ 4,5] provide recent overviews of the solidification transport phenomena and macrosegregation in ingot casting."

Jan 1, 1999

By Thais Cristina da Costa Caldas, Carlos Mauricio Fontes Vieira, Alline Sardinha Cordeiro Morais, Sergio Neves Monteiro

"This work has as its objective to evaluate the effect of the incorporation of a glass powder waste obtained from discarded and Hg-cleaned fluorescent lamp into clayey ceramics used to fabricate bricks and roofing tiles. Formulations were prepared with incorporation of the waste in amounts up to 10 wt.% into the clayey body. Rectangular specimens were prepared by uniaxial mold-press at 20 MPa to fire at 850 and 1050°C. The physical and mechanical properties evaluated were: linear shrinkage, water absorption and flexural rupture strength. The microstructure of the fired ceramics was evaluated by optical microscopy. The results showed that the waste incorporation significantly improved the evaluated properties mainly at 1050°C.IntroductionFluorescent lamps use mercury as a main component for its operation. This metal is potentially toxic and can contaminate soils, animals and water bodies. The problem is aggravated if considerations are made with respect to the amount of lamps that are commercialized and discharged in emergent countries like Brazil [ 1].By using appropriate recycling processes applied to discharging fluorescent lamps it is possible to reuse most constituents of these lamps into new productive processes. A study has shown that one million common fluorescent lamps can generate 900,000 tubes of clean glass [2]. Moreover, this Hg-cleaned gloss may be recycled in different products.In fact, to recovery and recycle all materials that constitute the lamp instead of discharging them. This action protects the soil avoiding the formation of environmental passives [3]. It is also relevant to mention that the glass from fluorescent lamps is 100% recyclable while its permanence in the environment would correspond to very long time pollution, since its decomposition time is undetermined [4]."

Jan 1, 2011

By James E. Simpson, Suresh V. Garimella, III de Groh

"An experimental and numerical study of the horizontal Bridgman growth of pure succinonitrile (SCN) and of a succinonitrile-1.0 mol. % acetone alloy (SCN-1.0 mol. % ACE) has been performed. Experiments at growth rates of 0, 2 and 40 µmis were investigated. The solid/liquid interface was stable (non-dendritic and non-cellular); however, it was not flat. Rather, it was significantly distorted by the influence of convection in the melt and, for the growth cases, by the moving temperature boundary conditions along the ampoule. For the alloy, the interface was determined to be unstable at growth rates greater than 2.8 µmis, but stable for the no-growth and 2 µmis growth cases. When compared to the pure SCN interface, the alloy interface forms closer to the cold zone,· indicating that the melting temperature has been suppressed by the addition of the alloying element. Two-dimensional computer simulations were performed for the no-growth case for both the pure and alloy materials. These simulations indicate that a primary longitudinal convective cell is formed in the melt. The maximum magnitude of velocity was calculated to be 1.515 mmls for pure SCN and 1. 724 mm/s for the alloy. The interface shape predicted by the computer simulation agrees well with the experimentally determined shape for the pure SCN case. In ongoing work, numerical simulations of the process during growth conditions are being performed.IntroductionIncreasingly, advanced materials used in the aerospace, automotive, optics and electronics fields require low levels of defects and high levels of solute uniformity. Directional solidification by the Bridgman process is widely used for synthesis of these high-quality materials. During Bridgman crystal growth, heat and mass transfer by both thermal and solutal gradient-driven convection and diffusion influence the shape of the solid/liquid interface and dopant segregation levels, and hence, directly determine the final crystal quality. Key process parameters include the applied furnace temperature distribution and rate of translation, ampoule properties and furnace orientation."

Jan 1, 1999

By P. Tim Johnson

Relentless increases in demand for nickel and vanadium for uses such as steelmaking, catalysts and battery materials, plus the growing financial and environmental costs of their primary extraction, have led to much interest in potential secondary sources of these metals. The presence of such metals in heavy fuel oils, bitumen and related materials offers both opportunities and challenges for potential extraction methods, especially with the growing production and importance of metal-rich fossil fuels around the world. For several decades, Tetronics’ DC plasma smelting technology has been used for the recovery of metals such as nickel and chromium from stainless steel melt dusts and other wastes in compact, environmentally-friendly and efficient plants. This paper explores the suitability of DC plasma smelting as part of a wider flowsheet with feed preparation and aluminothermic reduction techniques for smaller-scale extraction operations based on this important niche secondary source of these key metals.

By C. D. Mishra

The recycling potential for any gainful utilisation of the waste products is dictated by their quality, especially the chemical characterisation. The methods commonly used for the analysis of fly ash e.g. wet chemical, AAS, ICP-AES etc are time consuming. The paper describes a rapid XRF-based method for routine analysis of fly ash which involves preparation of local standards, optimisation of sample preparation technique and use of a simple PC-based software to account for interelement effects. The matrix corrected values are found to agree well with the wet chemical data.

Jan 1, 1992

By Jinliang Zhang, Jian Pan, Deqing Zhu

"Limestone and burnt magnesite were added to vary MgO content and basicity (CaO/SiO2 ratio) of pellets for investigating their influences on the properties of specularite pellets. At fixed MgO content, the addition of limestone does not affect on the properties of green balls significantly. The addition of burnt magnesite has obvious influence on the quality of green balls, especially on the thermal shock temperature. Without burnt magnesite, the thermal shock temperatures are about 400°C, and, the thermal shock temperature increases to 600~630°C by adding burnt magnesite. For preheated pellets, when the burnt magnesite is added, the compressive strength will be decreased. For roasted pellets without burnt magnesite, the calcium additives can form binding phase of calcium-ferrite, and suitable liquid phase will improve recrystallization of hematite, but excessive liquid will destroy the structure of pellets, so the compressive strength of pellet increases firstly and then decreases. When adding burnt magnesite, the compressive strength will increase as the basicity increases. When the basicity is more than 0.2, the compressive strength of the pellets various MgO content and basicity is above 2500N/pellet and then MgO-bearing fluxes can be added to prepare pellets with good high temperature properties.IntroductionWith the rapid development of the steel industry in China, oxidized pellets, possessing good mechanical and metallurgical properties, are becoming indispensable burdens for blast furnace ironmaking [1-3]. However, this has resulted in the shortage of domestic iron concentrates, so many Chinese steel plants begin to use imported hematite concentrate to prepare pellets. Compared with magnetite pellets, the hematite pellets require high roasting temperature and narrow roasting temperature range (1300–1350°C) and possess low compressive strength [4,5].1"

Jan 1, 2012

By S. A. Davis

In July of 1996, the Kroll process began production again at TIMET&apos;s Henderson, NV, manufacturing facility. This, after being shut down for several years due to low market demand for titanium. Faced with limited pond capacity and increasing costs for water and wastewater disposal and storage; process changes were made to recycle water used to wash Kroll titanium sponge back into the sponge leaching process. This idea was revisited from 1992-93, when three consecutive attempts to recycle water for this application were unsuccessful due to early pump failure. Since it was uncertain why previous attempts failed, a complete understanding of the existing system was first sought. This included reviewing piping and flow diagrams; taking field measurements for all the piping, valves, and fittings; analyzing the wastewater composition; and modeling the fluid dynamics and control of the system. The fluid dynamics of the system were modeled by breaking the piping network up into nodes and applying the Bernoulli equation to each segment. The fluid flowrate control valves were modeled for this purpose also and the models were used to help specify the required processing equipment and control ranges and tolerances. Once the project was completed, an operating procedure was prepared for operation, startup, and shutdown of the washer water recycle system.

Jan 1, 1999