Search Documents

By Valdeci Paula Alvarenga, Sergio Luiz Costa, Itavahn Alves da Silva, Filipe Bueno Carvalho, Varadarajan Seshadri, Carlos Antonio da Silva

Use of fluorspar in steel refining operations is one of the environmental concerns and as such reduced consumption of this material or substitution of the same is one of the objectives. Industrial runs were carried out at Aperam Steel making convertor unit (Timóteo, MG, Brazil) using recycled/briquetted slag for partial or complete substitution of fluorspar. Samples were collected from the metal bath and slag after oxygen blowing to assess dephosphorization with several combinations of recycled/briquetted slag and fluorspar. The results showed that partial substitution of fluorspar by BOF slag briquettes did not affect the efficiency of dephosphorization. In general average Phosphorus content was reduced to 0.010% in the case of partial substitution compared to 0.016% in the regular refining procedure with no substitution. This replacement also resulted in 40% reduction of the fluorspar consumption in the converter

Jan 1, 2015

By Takaaki Shibata

The Tamano Refinery has developed two new processes for removing the impurities, arsenic, antimony, and bismuth from an electrolyte. The first process involves bleeding the surface electrolyte in the electro-refining cells. The copper concentration level in the outermost layer is lower than that in any of the other layers, while the impurity levels are almost the same in all layers. Bleeding the surface electrolyte increases the amount of impurities removed in the liberator by approximately 20%. The second process involves adsorbing antimony and bismuth from the electrolyte by means of chelating resin. As the electrolyte passes through the packed column of chelating resin, antimony and bismuth are selectively adsorbed. They are then desorbed by means of hydrochloric acid, and then recovered in the form of a highly concentrated antimony chloride solution by means of evaporation. This process almost doubles the capacity for removing antimony from an electrolyte.

Jan 1, 1987

By M. J. Walker

The lead .smelter at Cominco's operations at Trail, B.C. has been undergoing. a modernization program since 1986. In that year a contract agreement was reached with German-based Lurgi GmbH which allows Cominco to construct and operate a lead smelter using Lurgi's QSL process. Cominco Engineering Services Ltd. (CESL), a subsidiary of Cominco Ltd., was contracted to provide project management, engineering, procurement and construction management? services for the project. The new smelter replaces the existing sinter-blast furnace plant ?and will have a capacity of up to 1601000 tonnes per year of refined lead. This new smelting proc.ess results in significant operating cost reductions and major environmental .improvements. Start-up of the new plant is scheduled for the fall of 1989. The metallurgy and the operating parameters, important to the design of the new smelter, are described together with projected deportments of lead, zinc, silver and minor metals. A plant description, will be given for the following major areas that make up the modernization project: the pressure filter operation for the preparation of ,zinc leach residues feed material, the QSL reactor and boiler itself, together with its feed system and process gas treatment, and the drossing plant with a new continuous drossing furnace and oxygen softening and thallium removal. Slag from the QSL reactor will be treated in existing slag furnaces until a subsequent second phase of the modernization is completed in the 1990s.

Jan 1, 1990

By A. R. G. Azevedo, G. C. Xavier

"The search for technological innovations in the Civil Construction takes as an objective the reduction of costs and increase of the productivity. However, these technologies demand analysis and studies of parameters of control that provide the quality of the products. With the intention of improve the knowledge on industrialized mortars used in mechanized projection machines, a characterization was done in the state anidro, fresh and hardening of three mortars, being each one of a State, Rio de Janeiro, Sao Paulo and Bahia. The tenors of water/ mortar was obtained through tests done in built environment, it varied from 0,17 to 0,26. From these results, the mortars were projected by his respective consistency, analyzing its compressive strength, and traction adherence resistance, in this way, the good performance of the revetments was provided.IntroductionThe market competitiveness of Construction has led companies to invest in construction processes and techniques in order to rationalize and optimize the buildings. Thus, changes emerged in coating system providing improvements in conventional materials and novel construction techniques, such as mortar industrialized and mechanized projection.Adopting projection equipment mortar is flagged as one of the solutions to reduce the interference of hand labor in construction, optimizing the performance of internal and external coatings, as well as streamline the production process and transportation, reducing lossesMaterials and deadline for execution of the casing(l)The process has been used due to its benefits, however, studies are necessary parameters for quality control of these mortars used in the projection to greater knowledge of mixing and market acceptance. It is therefore quite relevant information processing techniques available on the subject, as necessary to carry out research aiming at defining specific indicators of quality."

Jan 1, 2013

By Jun Lu, Min Chen, Wei-jian Su, Jian-zhong Luo, Yu-tao Lei

"In the case of treating phosphatizing wastewater containing zinc, zinc had an impact on the solution chemistry, especially on pH. Fe2(SO4)3 and CaCl2 were used as precipitators to remove phosphate from zincic phosphatizing wastewater and the optimum pH was investigated. Zinc ion had a significant effect on the optimum pH. The optimum pH ranges were 12.10(inlet concentration of 15.67mg/L, outlet concentration of 9.53mg/L), 3.04-5.50(inlet concentration of 11.97mg/L, outlet concentration of 0.44-0.26mg/L), and more than 10.72(inlet concentration of 12.24mg/L, outlet concentration of less than 0.47mg/L) under the conditions without precipitator, with Fe2(SO4)3 and with CaCl2 respectively.Introduction Phosphate coating is commonly used for protective coating of machine elements. Including oil removal by caustic washing, rust removal by acid washing, phosphatization and inactivation, the phosphatization process produces wastewater containing inorganic salt of high concentration, especially the phosphate, beyond the environmental standards and polluting environment seriously. What’s more, the wastewater from zincic phosphatizing technology also contains another pollutant, zinc. At present, Chemical Precipitation (CP) and Biological Nutrient Removal (BNR) are two of most common technologies of phosphate removal. BNR, such as A/O, A2/O and UCT technology, is suited for wastewater containing organ phosphorus of low concentration and CP for wastewater with phosphate of high concentration [1]. Researches on CP treating wastewater containing phosphate of high concentration, mainly focus on adding quantity of precipitators[2-5] and coagulants[2-4] and the choice of technologies[3-9]."

Jan 1, 2008

By Gaifeng Xue, Lijun Lu, Honghui Fang, Jiannyang Hwang

"Steel slag has been stockpiled in many steel mills due to its poor performance in various construction related applications. Free lime in steel slag has been considered as a major barrier for its utilizations. Composite of steel slag and powders of granulated blast furnace slag have been found an excellent cementitious material for concrete. Portland cement is not required in this kind of concrete. Concretes with various amounts of steel slag and powders of granulated blast furnace slag additions have been investigated. Physical and chemical properties of the products were examined. High performance concrete can be obtained. Field testing of the concrete products was conducted for various applications, including buildings and pavements, and the results demonstrated the soundness of the concrete. Drill cores of field tested concrete, with ages up to 26 years, were examined for the microstructures under SEM.IntroductionIn the steel industry, a major source of the solid waste is steel slag. Steel slag has poor stability in construction applications. This is a major reason that only a small amount of steel slag has been utilized. Some of the reported applications include the land filling/creation in the sea, road base materials, soil treatment for acid neutralization and micronutrients supply, and sintering aid in the sintering plant of the steel industry [1].To solve the stability problem for using steel slag as construction materials, the common approach is to find a method capable of depressing or eliminating the expansion of steel slag. Free lime in steel slag is the major component that causes the expansion. Aging and hydration pretreatment of free lime in steel slag are the well known methods for increasing the steel slag stability. However, there has been limited success on these approaches due to that a large portion of free lime is locked in the grains during the pretreatment process."

Jan 1, 2012

By Denise Nascimento, Alice Barreto Bevitori, Felipe Perissé Duarte Lopes, Renan Carreiro, Sergio Neves Monteiro, Isabela Leão Amaral da Silva

"Natural fibers obtained from plants have increasingly been used as reinforcement of polymeric composites in engineering applications. This is the case of the fiber extracted from the piassava palm tree, a native of the southeast region of South America, which for a long time has been used in simple items like brooms and brushes. Recently it was reported that the tensile strength of the piassava fiber varied inversely with the equivalent diameter. Following that previous work, the elastic modulus and the density dependence on the diameter of stiffer piassava fibers of the Attalea fiinifera species was investigated. Precise measurements with a profile projector and Weibull analysis of the experimental results indicated that both the elastic modulus and the density of piassava fibers also follow an inverse correlation with the diameter. Scanning electron microscopy observations of the microstructure and fracture surface showed that defects and participation of microfibrils are responsible for this correlation.IntroductionIn the past decades, both the increase in the price of the petroleum and climate changes due to greenhouse gas emissions are motivating the use of renewable and low cost natural materials as a substitute for energy intensive and CO2 contributor synthetic materials [1]. A typical case is that of natural cellulose-based fibers extracted from cultivated plants in comparison to glass fibers, which are extensively used for composite reinforcement. In fact, these natural lignocellulosic fibers are increasingly being investigated [2-6] as possible reinforcements of polymeric composites, and in some cases, successfully replacing glass fiber composites in engineering applications [7]. The automobile industry has remarkable examples of lignocellulosic fiber composite substitutions [8-10]. Not only do some of these fibers display specific mechanical properties comparable to glass fibers but their composites also contribute to lower equipment wear and better finishing of molded components [6]."

Jan 1, 2012

By Toshiki Kabutomori

In fuel cell powered automobiles, hydrogen is required to be stored in materials that have a hydrogen storage density of over 4 mass%; further, these materials should be capable of supplying hydrogen by using the waste heat from a fuel cell, which is at a temperature of 373 K, in order to match the mileage of gasoline-powered vehicles. A Ti-Cr-V alloy, which exhibits a BCC structure and forms a solid solution, is a promising candidate for onboard hydrogen storage materials. Although it has a large hydrogen storage capacity of over 3.9 mass%, the rechargeable hydrogen capacity is limited to approximately 2.6 mass%. In this study, the effects of fine pulverization of the alloy on PCT (hydrogen pressure-composition-isotherm) characteristics were investigated in order to improve the rechargeable hydrogen storage capacity of the alloy. From the PCT measurements of the finely pulverized samples of the alloy, a plateau in the absorption curve was observed to begin at a hydrogen concentration of 0.5 mass%; further, a rechargeable hydrogen storage capacity of 3.3 mass% was obtained. This was greater than that obtained from the sample that was not finely pulverized, i.e., 2.5 mass%. However, the plateau width in the desorption curve was 2.5 mass%, which was the same as that observed for the sample that was not finely pulverized. The increase in the rechargeable hydrogen capacity during absorption is attributed to the precipitation of the -hydride phase (MH~2) directly from the metal phase (phase). The precipitation of the phase (MH~0.5), which should be formed in low hydrogen concentrations, is suppressed as a result of a possible reduction in the internal defects such as dislocations, vacancies, and grain boundaries by fine pulverization and annealing of the alloy.

Jan 1, 2006

By Ana E. Bohé, Fabiola J. Alvarez

"The separation of nickel from the aluminum present in spent catalysts and different metallic industrial residues, is proposed in the following systems: alloy Al2Ni and the mixtures 50 wt% Ni + 50 wt% Al, 10 wt% Ni + 90 wt% Al2O3 and 12 wt% NiO + 88 wt% Al2O3. The experiments were carried out in a tubular reactor with a flow of 2 l/h of gaseous chlorine and from 200 ° to 800 °C. The final products of the reaction, extracted from the hottest zones of the reactor where characterized by XRD, SEM, EDS, AA and XRF, as NiCl2 y NiCl2.6H2O while in the coldest regions AlCl3 was deposited in the first two cases and in the other there was a residue of ?, a- Al2O3, sometimes mixed with some remainder of Ni and NiO. The procedure attained different separation factors which showed the optimun conditions for the recovery of both metals. Introduction Some studies of nickel corrosion were carried out in chlorine gas at temperatures above 950ºC, and suggested that nickel is not corroded below 538ºC. [1] However, in a previous work it was shown that the chlorination allows the separation of nickel from aluminum and the formation of NiCl2 was detected from 200ºC in binary mixtures Ni-Al 50 wt%, for isothermal conditions in chlorine flux. [2] Other researchers obtained selective chlorination above 650ºC of a fly ash containing 1.4 wt% of Ni and other metals (V, Mg, Al and Fe). The Ni was separated from the Mg and NiCl2 started to vaporize at 550ºC and was after condensed in a zone of the reactor above 380ºC with 90% of purity. [3]"

Jan 1, 2008

By Leiting Shen

The thermodynamics of tungsten ore decomposition in mineral acid and alkaline solutions were studied. The published thermodynamic data of tungsten minerals were collected and assessed. The Gibbs energies of CaWO4 (−1538.43 kJ/mol), FeWO4 (−1053.91 kJ/mol), MnWO4 (−1206.08 kJ/mol), H2WO4 (−1003.92 kJ/ mol), and Na2WO4 (−1455.58 kJ/mol, aq) at 25 °C were adopted in the calculation using HSC software. The results show that CaWO4 is decomposed more readily in Na2CO3 solution than in NaOH,while FeWO4 andMnWO4 aremore reactive inNaOH solutions. Froma thermodynamic point of view, tungsten ore decomposes easily in acid solutions despite most ΔGo T increasing slightly with temperature. Oxidizing Fe2+ to Fe3+ in acidic solutions facilitates decomposition of FeWO4, and the reaction of CaWO4 in H2SO4 solution occurs more easily than in other mineral acids, due to the formation of sparsely soluble CaSO4. The results fit well with the experimental data and industrial experience previously reported in the literature.

By N. Kanari

Chalcopyrite concentrates and their pure constituents were chlorinated by C12+N2 between 25 °C and 750 °C. The reaction products were analyzed by SEM, XRD and chemical analysis. The effect of gas flow rate and chlorine content of the gas mixture on the reaction rate were investigated. At room temperature, these solids start to react with chlorine giving metal and sulfur chlorides. Complete reaction is achieved at about 300 °C and the iron and sulfur chlorides were fully volatilized. The chlorination residue is composed of valuable metals' chlorides. A simplified flow - sheet for the treatment of chalcopyrite concentrates by chlorine was suggested.

Jan 1, 1998

By Seyed Mahdi Abbasi, Adel Sheikhhosseini

"This research was conducted to study the changes of microstructure, chemical composition and mechanical properties ofIN718 superalloy after adding aluminum to the ESR process slag. The experiments were performed in VIM and ESR furnaces. The results showed adding 1.5 percent aluminum to the slag increase lave phase in the IN718 samples from 0.34 percent in the base sample to 3.0 percent. It also indicated that the more increase of aluminum in slag cause decrease in the aluminum absorb yield in the superalloy.it is observed that increasing aluminum from 0.7 to 1.1 and then to 1.5 percent caused a decrease of absorb from 91.4 to 76.3 and 74.6 percent respectively due to increasing of aluminum oxidation. According to the results, tensile strength increased and ductility declined in the IN718 samples mainly because of rising the amount of y' volume fraction.IntroductionIN718 superalloy is an iron-nickel base superalloy with constant mechanical properties at medium at high temperatures. For the past seven years a considerable amount of time and effort has been expended by both suppliers and users in the study of Alloy 718 [ 1]. The interest in this material stems not only from the interesting metallurgy associated with the alloy, but with the large usage of the material in numerous applications In fact many people believe that the projected use of this alloy increase significantly over the next several years, The large use of Alloy 718 is the result of its performance in respect to high strength, good ductility, good repair weld ability and from its versatility of being supplied in various product forms. This superalloy is used in wide ranges of industries such as aerospace and gas turbines [2]. In the past more than 20 years many researchers did a lot of work to improve the structure stability of IN718 at high temperatures and intended to develop a new 718 type alloy to be used beyond 650 °C. One of the methods is to control and phase precipitation behavior by means of adjustment of Al, Ti and Nb contents. The other idea is to strengthen the matrix by altering the content of solid solution elements such as W and Co. The adjustment of these alloying elements can change phase precipitation behavior [3]. If detailed information dealing with phase precipitation behavior can be obtained before experimental work for alloy development, a lot of time can be saved and the development cost can also be reduced. In recent years, computer modeling based on experimental data plays an increasing role in alloy design and development. Adding Al to the Iron and Nickel increas the strength of superalloy by formation of y phase and subsequence formation of n phase. Ti in IN718 superalloy also helps the formation of MC carbides and gamma prime phase. Increasing Al/Ti and (Al + Ti)/Nb will lead to form finer particles of y'. More uniform distribution of the precipitates and enhancing stability of y' in IN718 superalloy [ 4]. Adding Al to slag of ESR process can reduce the oxide inclusions because of the strong tendency of Al to oxidation. In addition, tensile properties of IN718 superalloy improve. The most significant inclusions in IN718 superalloy are Alz03 and TiN that were found in agglomerate forms. Thermodynamic calculation results indicate that the effect of increasing Al shows a strong increase in solvus while phase solvus shows mildly decrease when Al level is less than 2%, after that it dramatically decreases [ 5]. Laves phase precipitation and the appearance of phase are occurred when Al content reaches 2%. In fact, when Al content is beyond 1.5%, phase has already precipitated in a considerable scale. Shows the fraction of increases greatly while the fraction of phase decreases remarkably with the increment of Al content. Based on thermodynamic theory, if these particles were not existed in the melt during cooling agglomeration would not accrue and the superalloy will be cleaned By adding Aluminum to the slag, the metal reacts with oxyge"

Jan 1, 2013

By H. Dong, J. J. Valencia, L. Nastac

"A comprehensive computer model was developed to understand and optimize the centrifugal casting process for manufacturing TiC/Al-bronze friction drums. Performance of these components requires proper distribution of TiC particles, which is shown by dimensional analysis to be dominated by centrifugal buoyancy effects and solidification kinetics.The model addresses the following: (1) a rheology-viscosity model of the interference between moving particles, (2) engulfment (entrapment) or pushing of particles in the mushy region by the advancing solid/liquid interface, (3) nucleation and growth of equiaxed and eutectic phases, (4) effects of particle size, particle concentration, and cooling rate on the final grain size, and (5) the impingement effect of particles on the nucleation and growth kinetics of solidifying microstructure.Parametric studies were conducted using the computer model to investigate the effects of various process and material parameters on the distribution of TiC particles. The effects of the volume fraction, size, and morphology of the particles (including clusters and agglomerates) on the particle distribution were evaluated in detail. The complex interaction between the solidifying structure and insoluble ceramic particles in centrifugally-cast metal-matrix-composites was also investigated.The model predictions of particle distribution and microstructure were validated with experimental data for centrifugally-cast A356/SiC and TiC/Al-bronze alloys.This work was conducted by the National Center for Excellence in Metalworking Technology, operated by Concurrent Technologies Corporation under contract No. N00140-92- C-BC49 to the U.S. Navy as part of the U.S. Navy Manufacturing Technology Program."

Jan 1, 2000

By Bingguo Liu, Daifu Huang, Jinhui Peng

"The conditions to prepare U3O8 by calcination from ammonium diuranate were optimized, and the response surface design method was applied to analyze the influence on the total uranium and U+4 of calcination temperature, calcination time and mass of sample. A quadratic equation model for the total uranium and U+4 of U3O8 was built and the effects of main factors and their corresponding relationships were obtained. The analysis of variance shows that calcination temperature and calcination time significantly affected the value of total uranium and U+4 of U3O8. The optimal calcination conditions were as follows: calcination temperature 931.83 K, calcination time 24.32 min and 43.89 g. Under these conditions the value of total uranium and U+4 of U3O8 was 84.78% and 28.02%, respectively. The validity of the model was confirmed experimentally and the results were satisfactory.IntroductionNuclear energy is clean, effective, and a sustainable from of energy. It plays an important role in overcoming the impending global energy crisis, and in reducing energy vulnerability. In addition, nuclear energy is a possible cheaper and cleaner source of energy compared to fossil fuels, with no not really, mining of uranium produces CO2 contribution to green house gases [1]. Uranium dioxide, one of the most important fuel pellets used as nuclear fuel in light water reactors, is manufactured by calcining ammonium diuranate to triuranium octaoxide, followed by its reduction to uranium dioxide using cracked ammonia at 700°C [2]. Earlier attempts to optimize the important calcination process through several common techniques have not yielded desirable results [3]. These techniques either rely on the classical one parameter at a time approach that ignores the combined interactions between physicochemical parameters, or are theoretical in nature. Furthermore, these techniques also require large number of experimental data to be generated [4]. In order to produce triuranium octaoxide in an optimized manner, which considers the interaction of different process parameters [5], there is a need to adopt a multivariate statistical technique."

Jan 1, 2011

By Alessandro Navarra, Joël P. T. Kapusta

"The converting cost modeling software introduced by Ng et al. in 2005 [1] has been extended to consider the reprocessing of reverts and copper scrap. The original model evaluated the operational costs of a Peirce-Smith converter; algebraic relationships had been implemented with arrays (to represent matrices, vectors and scalar ratios). The new software brings flexibility to the underlying thermochemical balances, by using linked-lists instead of arrays. It is now possible to consider the blending of several feeds, including reverts and scrap.The software computes the length of the converting cycle from the Fe and S content of the charge together with the blowing rate; the times required for other operations (charging, skimming and idle time) are also accounted for. The costs of consumables such as flux, fuel, oxygen or compressed air are all evaluated. Downtime, labor, and materials for converter lining repairs are also considered. The software is easily extended to examine the costs of alternative operating strategies or injection technologies such as sonic single pipe injection and sonic shrouded injection. The potential cost benefits of alternative operating procedures and technologies are discussed through example calculations."

Jan 1, 2009

By Russell E. Clemons

Coarse-crystalline granite, quartz syenite, syenite, meladiorite, and anorthosite in the Florida Mountains, southeast of Deming, New Mexico, were originally mapped as Precambrian. They were remapped in 1971 and some of them described as Mesozoic intrusives. Several subsequent papers presented Precambrian and Ordovician ages. Zinc, lead, copper, silver, gold, manganese, fluorite, and barite mineralization in the Florida Mountains invite more extensive exploration. Clarification of ages of rocks and periods of alteration and mineralization are necessary for efficient exploration. Field observations combined with petrographic studies strongly suggest that all the coarse plutonic rocks are Precambrian and most were altered extensively by late Tertiary hydrothermal activity.

Jan 1, 1982

By R. G. Reddy

The Margules .equation is used for interpreting excess Gibbs energy of several ternary systems. In the present study activity coefficient of 'a dilute solute, 2, in a binary solvent 1-3 was derived. The derived expression is used to interpret logarithmic activity coefficient of oxygen and sulfur in several metallic systems. Self interaction parameter of the solute is derived from the partial function of solute using constant compositional path. An expression for logarithmic activity coefficient and self - interaction parameter of solute is also derived using Maclaurin infinite series. The derived equation is based on Maclaurin infinite series used successfully to deduce thermodynamics of self interaction of oxygen as a interstitial atom in two metallic systems. The predicted thermodynamic parameters values using Maclaurin infinite series and Margules. equations, are in excellent agreement with the experimental data and also our predictions are far more accurate than the predictions made by other models.

Jan 1, 1996

By Guanghui Li

In the paper, the recovery technology of gallium from zinc-leaching residue by cold-bonded coal-based direct reduction process following magnetic separation was developed. The results show that the scattered metal Ga can be concentrated obviously after the reduction of zinc-leaching residue briquette and magnetic separation of reduced product. At the same time, the volatilization of Zn in the residue is enhanced during the reduction. When the residue, bear¬ing 18.60% Zu.21.18% Fe and 527 g/t Ga, was reduced with coal at 1100°C for 150 min, the results of Zn volatilization of 9842% and Ga recovery of 89. 10% were obtained in reduction. After magnetic separation of the reduced product, the concentration of Ga in sponge iron is 2164 g/t, and the separation recovery of Ga reaches 92.42%. The enriched mechanism of Ga during reduction -separation process was studied by using electron microscope, scanning elec¬tron microscope, energy spectrum and mineralogical analysis. The investigations show that there is no formation of independent phase of Ga during reduction process. The Ga occurs mainly in metallic iron phase (the concentration of Ga in metallic iron phase is 0.04%-0,4%), in addition, there exists a little Ga in poorly crystalline sulphide (o.08%-0./5Y& Ow). But Go does not exist in most of glass and silicate phase. The affinity of Ga for metallic iron is the enrichment basis of Go in reduction, and it is also in favor of recovering Go during magnetic separation. Key Words: Gallium Zinc-leaching Residue Cold- Bonded Direct Reduction

Jan 1, 2003

By Pengfu Tan

A thermodynamic model and computer program, CuModel, has been developed to model the distribution behaviors of Cu, Fe, S, O, Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag, copper loss in the slag, and heat balance in copper smelting process, matte converting process and copper con-tinuous smelting process. It can be predicted for any set of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxy-gen-enriched air. This model accounts for physical entrainment between matte and slag phases. It can be used in Isasmelt process, copper flash smelting process, Mitsubishi process, P-S con-verting process and Noranda process. The predictions by the present computer model are com-pared with the known commercial data from Guixi Smelter in China, PASAR Corporation in Philippines, Horne Smelter in Canada, MIM Limited in Australia and Naoshima Smelter in Ja-pan. The agreements between the computer predictions and the commercial data are excellent. In this paper, the applications of CuModel in the copper metallurgical industries have been pre-sented. CuModel has been used by Daye Smelter and Guixi Smelter in China, and by PASAR in Philippines as well.

Jan 1, 2004

By A. H. Rhoades

The modern polarizing microscope with such accessories as cameras, infrared devices, reflectance and/or transmission photometers, indention hardness, and heating stage is used to characterize coal, coke, and other carbon forms. It allows characterization of coke by-products, such as tars and pitches and their insoluble residues. A useful product of the microscopic approach is the coal petrographic analysis which permits the prediction of coke strength carbonization pressure and volume change. Carbonization tests are expensive, time-consuming and require large amounts of coal. Tests on the coke show it to be strong or weak but give no indication of why. Petrographic analysis requires grams of coal and yields data that indicates why the coal produces coke of a given quality. Small samples from drill cores are sufficient for petrographic analysis. These data are also used to optimize blends for coke production. When coke-plant problems occur, ~he microscope can be used to check the coal blend proportions, as well as for weathered coal. Microscopy is useful in spore correlation work which may be a prerequisite to sound coal reserve estimates. Dispersed vitrinoid reflectance studies are used to determine the degree of organic metamorphism which serves to establish oil and gas deadlines. Tars and pitches are examined microscopically for the amount of normal solids as well as the size of undesirable carry-over solids resulting from pollution abatement practices in coke works. The microscope is also used to study coals for gasification and liquefaction.

Jan 1, 1981