Search Documents

By D. M. Fermino, C. G. Bastos Andrade, V. F. Justo, F. R. Valenzuela-Diaz, M. G. S. Valenzuela, C. Volzone

The present paper presents the study of light green smectite clay, from Paraiba, Brazil, submitted to mild acid attack under moderated conditions. Usually, clays are subjected to treatment with strong inorganic acids at temperatures near the boiling point and at high acid concentrations and then, widely used as bleaching agents. The treatment occurred under bellow boiling temperature and at short times of reaction (90°C, reaction times of 1, 6, 12, 18 and 24 hours in close reactor, concentration of the aqueous solution of hydrochloric acid 1.5 M, clay/acid solution ratio of 1g/10mL). The purpose of these attacks is to reduce the concentration of impurities providing color, with minimal change in the clay minerals structure, aiming at use in products of high value such as cosmetics and polymer/clay nanocomposites. The raw clay and the attacked samples were characterized by X-ray diffraction (XRD), cation exchange capacity (CEC), stereomicroscopy, scanning electron microscopy (SEM) and energy dispersive X-ray detector (EDS).

Jan 1, 2015

By Peter Fischer

A demonstration plant for QSL technology with a continuous through-put of up to 10 t/h concentrate has been in operation at the Berzelius smelter, Duisburg, Germany since early 1981. In the QSL-process, both oxidation and reduction steps are performed in a single horizontal long cylindrical reactor. In the present demo-reacior, 2.5 M diameter by 22 M long, these steps are separated by a low partition wall with an underflow opening, to prevent backmixing of slag. -Tests on a variety of concentrates, including high-lead Missouri-type material and lower grades, have shown recoveries and consumables indicating very attractive economics. Investment cost estimates further enhance the economic attractiveness. Environmental protection afforded by the QSL system is a major advantage. The process has proven its reliability and versatility and is now ready for commercialization. Continued test work, including smelting secondary lead materials, is planned.

Jan 1, 1983

By Yun Li

In 1999 Yunnan Copper Corporation (YCC) decided to modernise their copper smelter and change the existing sinter plant I electric furnace process to a combination of ISASMEL T and electric slag cleaning furnace. The main aim of the project was to improve the environmental performance and decrease the energy consumption. Generally the project has been successful, partly attributable to the selection of a reliable and fully demonstrated technology. The design capacity for the ISASMEL T furnace is 600,000 tonnes of dry copper concentrate per year. The furnace has been running smoothly since heat up in May 2002. YCC expended considerable effort in the preparation for plant operation. An extensive training program for key YCC personnel at the Mount Isa Copper Smelter improved their understanding of the process significantly and ensured successful hand-over of the technology. This paper describes the project history and summarizes initial operating results.

Jan 1, 2003

By Andreas Orth

Outokumpu Lurgi Metallurgie has developed a process for the calcination and reduction of laterite nickel ore tines where the reduction of iron and nickel to the wustite/metallic states respectively, is performed in a fluidized bed reactor using reduction gas generated very cost effectively from natural gas in an autothermal catalytic reactor. As an option coal can be used as reductant as well as additional fuel. The process of reduction and calcination is very energy optimized. It uses the off gas from the fluidized bed reduction reactor, which still contains energy, to dry and calcine the nickel ore fines in a primary stage circulating fluidized bed (CFB) reactor. The product shows high metallisation of nickel and iron oxides reduced to the wustite stage. This results in considerable energy savings in smelting the prereduced product to ferro-nickel. Alternatively the product can be leached to produce nickel. Laboratory tests showed very high recovery of nickel and cobalt. Keywords: Fluidized Bed, Prereduction, Calcination, Ferro-Nickel

Jan 1, 2004

By Stanko Nikolic

One of the keys to success in process development is incremental scale-up, allowing for potential problems to be identified and rectified. The ISASMELT™top submerged lance (TSL) process was developed to maturity using this method by Mount Isa Mines, now owned by Glencore. Commercialization only occurred once the process had been proven on each scale and as a result the ISASMELT™ technology now operates successfully around the world. An important parameter in the evolution of the technology has been the furnace campaign life. The initial commercial scale furnaces had minimal water-cooling. Although this led to shorter campaign lives, an extended development program resulted in the achievement of four-year campaign lives, without any water cooling. In tandem to the refractory designs Glencore Technology, supplier of the TSL technology, has progressed cooled copper lining designs for application to both the ISASMELT™ and ISACONVERT™ furnaces allowing for ultimate flexibility in the lining choice. This allows each ISASMELT™ operating site to minimize their overall life-cycle costs by balancing their campaign life with lining costs, energy inputs, and other shutdown requirements.

By Marco Olper

The CX-EW technology, developed by B.U.S Engitec, is improved introducing besides the battery paste electrowinning, the direct electrorefining of metallic lead (grids and poles) obtained from CX breakers. This new concept of electrorefming the antimonial lead scrap is aimed to the production of 99.99 lead and of slimes with high antimony content, avoiding gaseous emissions in melting lead scrap, and expensive and pollutant thermic refining operations. In this way, practically all lead content in the battery is available as 99.99 lead, hence with a wider market for the lead recyclers. This paper will describe the tests performed on a pilot plant scale with special reference to the relatively low energy consumption of the process.

Jan 1, 1993

By Sergio N. Monteiro

The interface between the matrix and the reinforcing fiber plays an important role in the efficiency by which an applied load is transmitted through the composite structure. The shear stress at the fiber/matrix interface can be associated with this load transference and,consequently,affects the composite strength. In the present work, pullout tests were used to evaluate the interfacial shear stress of curaua fiber in epoxy matrix composites. A small critical length was found for the curaua fiber embedded in epoxy, which corresponds to a relatively weak fiber/matrix bond and lower interfacial strength.

Jan 1, 2009

By Guanyong Shi, Zhihe Dou, Cong Wang, Ting'an Zhang, Hongyan Zhang

We prepared the CuCr alloy by thermit reduction-electromagnetic casting. But there are the defects such as stomata and oxide inclusions in CuCr alloy. In this paper, the existing state and distribution of inclusions and stomata in CuCr alloy are systematically analyzed. The alloy was characterized via SEM, EDS and metallographic microscope, in which the existing state and micro-structural defects of inclusions are analyzed. The results show that: there are three distinct areas: copper-rich areas, chromium-rich areas and the inclusion areas. Inclusions are mainly in the form of stomata and Al2O3 phase, mainly locating in the copper-rich phase and the interface area of chromium-rich phase and the copper-rich phase. Then, the composition of phases of the smelting slags and alloy were characterized via XRD. The results show that: the slag consists of Al2O3 and a little of Cr, the alloy consists of Cr, Cu and a little of Al2O3.

Jan 1, 2015

By Yong Kuk Park

The horizontal cold chamber die casting process can produce a wide range of near-net shape, non-ferrous castings with small dimensional variation, excellent surface finish and very complex geometries. However, top quality die castings can be achieved only when optimal performance of the cold chamber and plunger is maintained during the molten metal injection phase of the process. Cold chambers (shot sleeves) are known to deteriorate fast and sometimes fail catastrophically because of poor design. Catastrophic fracture and wear due to deformation are leading causes to degrade quality, increase downtime and thereby decrease productivity and profitability. Therefore, a systematic approach to minimize irregular and adverse conditions which prevent an intended injection profile, is highly desirable. To eliminate them, design criteria for shot sleeves were developed using analytical tools and available experimental data. The correlation between design and mechanical failures of shot sleeves was shown by the data obtained from the die casting industry. Also, the relationship between die casting process parameters and deterioration/ failure mechanisms were carefully evaluated.

Jan 1, 1996

By Mingchun Lu, Yunjin Yan

"This paper describes a new type of bell-less top installed on two relined blast furnaces at Tianjin Iron Works and another new-built at Echeng Steel Works in China. A compact installation was presented for existing furnace top innovation with the least reformation of existing top structure. A water cooling and sealing gearbox used for driving the chute discards completely the traditional idea about necessity of continuous supply of cooling gas for the gearbox. A multiring spreader and its dozens of selectable charging patterns enables an operator to achieve optimal burden distribution easily under the condition of a minimum investment of control equipment. Some useful conclusions have been made through a small-size model and a full-scale model tests. The excellent characteristics and the superiority of the new top have been fully proved at both works.IntroductionIt is known that there are some advantages with the bell-less top of a blast furnace: suitable for furnace to operate at high top pressure, capable of realizing optimal burden distribution, less investment and maintenance costs, etc. But why do most of blast furnaces in the world still remain using conventional bell top. One of the concerns is that current bell-less tops still have some shortcomings:1) The height of a current bell-less top might be lower than three or four-bell top or two-bell plus valve seal top, but still much higher than an ordinary two-bell top.2) The gearbox for driving the rotating chute is positioned onto the lip of the furnace. It is subject to attack by crude hot bf gas. Continuously pumping cooling gas (pressurized nitrogen or clean bf gas) into the gearbox is indispensable to withstand such a harsh working environment. Therefore, a plant furnished with blower8 and its ancillaries has to be built, It involves a large sum of investment and much expense in its annual running costs.3) Although the current bell-less charging device as a means of controlling burden distribution possesses a wide range of freedom, it is difficult to realize optimal burden distribution. There are some large blast furnaces realized better burden distribution, but sophisticated control means is indispensable so that the investment of control means is much higher."

Jan 1, 2000

By W. G. Davenport

The offgas from flash furnaces inadvertently contains dust. The dust contains 25 to 30% Cu so it must be treated for Cu recovery. This is almost always done by recycling it back through the flash furnace*. This chapter shows how dust production/recycle is included in our matrix calculations. It then discusses the effects of dust production/recycle on flash furnace industrial oxygen and oil requirements. It concludes that re-smelting of dust requires considerable industrial oxygen and fuel, so that dust production should be minimized. Recycled dust also takes the place of new concentrate in the flash furnace feed system, decreasing Smelter productivity -another reason to minimize dust production. Compositions of industrial dusts are given in Appendix VII and Table 18.3. Industrial quantities are given in Tables 2.1, 3.1, 19.1,20.1' and Appendix VI.

Jan 1, 2001

By M Kolbe

Co-Cu exhibits a metastable miscibility gap in the region of the undercooled melt. Specimens have been undercooled and solidified containerlessly into the metastable miscibility gap in an electromagnetic levitation facility (EML) and in drop tube (DT) experiments. Due to the high undercooling the velocity of the solidification front is very high and the microstructure is frozen in instantaneously. The microstructure of samples processed in the EML is influenced by the electromagnetic stirring due to the induction of electrical currents into the melt. A variety of microstructures has been observed. After undercooling below the binodal the liquid melt separates into the Co-rich L1-phase and the Cu-rich L2-phase. Two basic morphologies of the L1-phase can be observed, they can be attributed to the transition in dendrite growth from diffusionally and thermally controlled to only thermally controlled growth. Transient microstructures are observed after solidification in the vicinity of the binodal. Drop tube experiments, which lead to a rapid solidification of a distribution of droplets under reduced gravity conditions, in contrary allow for the observation of the early stages of demixing: the microstructure shows a homogeneous distribution of spherical particles of the minority phase in the droplets. The cooling rate of the droplets and its dependence on the droplet radius has been calculated. The solidification velocity as a function of undercooling has been measured in the EML for the composition Co-lB.Bat%Cu. The data are analysed in the framework of the LKTlBCT model with a velocity-dependent distribution coefficient as well as within a model of Galenko and Danilov using a kinetic growth coefficient of u=0.22 m/Ks.

Jan 1, 2002

By M. Z. Sukiennik

A static method for vapor pressure measurement up to 1450 K and above 1 hPa is presented. The method is designed for equilibrium and kinetic studies of metallic systems, including those with a chemical reaction. Application examples are given for determination of activities in condensed phases, and heterogeneous reaction rates and equilibrium constants.

Jan 1, 1993

By Zhigan Deng

Ni–Mo ore is a black shale containing amorphous colloidal sulfides which have highly active. The oxygen pressure leaching behavior of nickel from black shale in aqueous media is presented. The effects of agitation speed, temperature, oxygen partial pressure and particle size on the rate of nickel leaching were determined. The results indicate that at low temperature hydrothermal and excess oxygen presence, the amorphous sulfides are easily oxidized to sulfuric acid and sulfate, and leaching nickel. The mathematical analyses of the experimental data for various experimental conditions indicated that the dissolution process was controlled by the chemical reaction during the early stage of dissolution, and was then controlled by liquid-film diffusion. In the initial stage of leaching, the reaction depends on oxygen partial pressure.

By Dirk Verhulst, V. I. Lakshmanan

Why Chloride Hydrometallurgy?The most available, cheapest and best known reagent for treating ores and other raw materials for the metallurgical industry is sulfuric acid. Hydrochloric acid is second in line. What often happens is that a process is developed on the basis of sulfuric acid, and that at some point the question arises: wouldn't hydrochloric acid do this better?Considering hydrochloric acid immediately opens a very interesting field of research. To summarize a few comments from another paper presented at this symposium [1]: chlorides are far more soluble than sulfates (with a few interesting exceptions); the hydrogen ion activity is greater in chloride than in comparable sulfate solutions; higher oxidative conditions are possible; regeneration is more straightforward; more diversity is possible and better conditions for the separation of species can be found for solvent extraction and ion exchange; sulfur in the ore can be separated as elemental S; higher metal concentrations in solution and more flexibility in the chosen oxidation state means significantly lower energy costs.Also, the volatility of many chlorides at higher temperature allows further separation without the need to go to a different system. Chlorides also form molten salts with a low melting point, providing another means of separation and purification in the same chloride medium.

Jan 1, 2011

By Edward Peters

Scandium (Sc) has unique properties and is one of the more valuable elements in the periodic table. Scandium can be used in solid oxide fuel cells and to produce high strength aluminium alloys of value, for example, in the aerospace industry. Scandium is often grouped together with the rare earth elements (REE). Amongst others, scandium can be found in bauxite residues, so called red mud. It is possible to extract and enrich scandium from red mud by leaching and solvent extraction. Scandium can then be recovered from the pregnant strip liquor by crystallization. The strip liquor will however still contain certain impurity elements. In the present work, a method for obtaining a pure scandium solid phase by direct crystallization from the strip liquor is evaluated. It was found that Fe and Ti co-precipitate with Sc under the conditions employed.

By Tianzu Yang, Weifeng Liu, Shu Bin, Lin Chen, Wanda Bin

"Vanyukov Process has been mainly applied for processing copper and nickel sulfide ore for more than 30 years. Based on the understanding of the Vanyukov Process, researchers from China introduced the technology into the areas of lead, antimony and bismuth extraction by changing the furnace structure and technical flow, which greatly extended the application area and raised the processing efficiency, thus developed the oxygen-rich side-blow bath smelting (OSBS) technology in 2000. This contribution reviews the history of OSBS technology from four respects: the quantity, the furnace structure, the process flow and the application area. Its potential research direction and industrial application are also summarized.IntroductionVanyukov bath smelting furnace and related bath smelting technology were developed by researchers from Soviet Union who devoted comprehensive research on fundamental theory as well as engineering technology [1,5]. Vanyukov process has been applied for large industrial production since the 1970s and it is still one of the major methods in modem pyrometallurgy process. The appearance ofVanyukov double district furnace and joint double furnace in the past ten years, which are applied for copper smelting, is the most valuable advances of the Vanyukov process [7,8,9]. However, the application ofVanyukov process was limited in copper and nickel sulfide ore smelting, and few countries adopted this process except Soviet Union."

Jan 1, 2013

By Robert G. Robins

Precipitation of ferric arsenate is an effective method for removing arsenic(v) from hydrometallurgical process solutions. The solubility and stability of this compound. FeAs04.2H20, has received some attention in recent years and the reported solubilities of amorphous and crystalline material have varied considerably. This paper reviews previous studies and reports some recent work with a consistent model to explain the variable results. Free energy data for ferric arsenate and its associated dissolved complexes are presented.

Jan 1, 1990

By G. H. Khoe

Neutralisation of acid uranium mill tailings with lime or other alkaline materials is usually practised to reduce the dissolved concentration of heavy metals and radio nuclides. Computer modelling of this process was carried out using the geochemical equilibrium code MINTEQA2. Computed dissolved metal and sulfate concentrations were compared with laboratory-based experimental data. It was found necessary to include the modelling of adsorption of trace metals (such as uranium and lead) by the precipitated ferric hydroxide in order to obtain acceptable concentrations in the neutralised liquors. There were limitations of the modelling exercise due to important aspects which were not addressed or properly accounted for such as chemical reaction kinetics and the effect of high ionic strength. These are discussed in the paper.

Jan 1, 1991

By A. M. Alfantazi, M. Boissoneault, D. B. Dreisinger, J. Synnott

Acid mist generation is a major concern in zinc, copper and nickel electrowinning industries and there is a strong environmental drive to control its emission into the work environment. Foaming reagents are typically added to the electrolyte to alleviate this problem. In zinc electrowinning, Licorice and Saponin are examples of foaming reagents used for this purpose. In order for the foaming reagent to be effective, its foaming behavior must be determined. In this work, a test procedure was developed to study the foaming characteristics of various surfactants for use as foaming agents to control acid mist in aqueous metal electrowinning. This new test was termed as "mini-flotation test" and it was used to study the foaming behavior of a large number of reagents in an industrial zinc sulfate electrolyte under simulated zinc electrowinning conditions (gas sparging). In addition, the influence of important process parameters such as current density, electrolyte temperature, reagent addition level and sulfuric acid concentration on the foaming characteristics of the electrolyte for each surfactant were investigated. The results of this study have identified the most important factors that influence foam formation, growth and stability. This method could be used as a process control for reagent addition in the cellhouse by generating a calibration curve for the optimum electrolyte conditions.

Jan 1, 1997