Search Documents

By P. A. Gray

Artificial ground support has developed into a relined science over the past 20 years. From reactive support systems such as timber props and steel supports, to active systems such as roof bolts and cable anchors, ground support technology has now developed efficient systems that work well in many instances. However this paper demonstrates that there is still a long way to go to develop optimum ground support systems. Some conventional rock bolts and cable anchors emphasise their tensile capacity only, without considering other factors such as their shear strength or shear modulus, or if the support member can transfer all of its support capacity to the surrounding rock. Examples are given of the use of ground anchors with high tensile and shear capacity in underground coal mining as well as examples of slope failures in open pits where the cable bolts have remained intact because they have been unable to transfer their full capacity to the surrounding weak rock mass. For underground coal mines, speed of installation is also of primary concern, but it must also have high tensile and shear capacity both in terms of strength and stiffness. Ground support systems of the future must therefore address these problems. An innovative new rock bait is discussed which goes some way towards solving these problems. This new rock bolt is screwed into the rock and thus has a direct mechanical interlock with the rock. Initial field results show that it has an extremely high anchor capacity and can be fully installed in approximately 30 seconds. It has considerable capacity to improve the productivity of the coal mining industry.

Jan 1, 1992

By Kevin J. Ma, John Stankus

"In order to access remote reserve areas, some U.S. coal mines have to maintain aged underground entries for a great distance. However, high humidity, warm temperature, and time dependent deterioration can cause progressive roof deterioration and unexpected roof falls can, pose a great challenge to ground control engineers. With an active belt structure in place and limited space, re-bolting becomes very costly, less effective, and, sometimes, impractical and unfeasible. To gain long-term entry stability and serviceability, operators typically rehabilitate the aged belt entries by installing standing steel set supports. In the last several years, Keystone Mining Services, LLC, (KMS) has assisted many coal mines with their belt entry rehabilitation projects, evaluated the ground condition of various aged belt entries, and designed different standing steel set support systems. This paper presents a case study of a large-scale roof fall that occurred at an aged belt entry in a mine located in an eastern coalfield, analyzes root causes of excessive deformation of square sets that were installed in an adjacent entry, evaluates the adequacy of an existing rehabilitation square set, and develops remedial recommendations for future rehabilitation practice. Based on the case study, the paper outlines design guidelines for rehabilitation steel sets that include field evaluation, engineering considerations, design assumptions, steel structural analysis, and field installation quality control. INTRODUCTION With gradual depletion of shallow coal reserves, some underground coal mines have to maintain long-term entries (belt, track, return airway, etc.) for a great distance in order to access remote coal reserve areas. However, due to high humidity, warm temperature, and aging in the belt entry, roof strata weathering and pillar degradation become more and more severe. Progressive roof deterioration poses a great challenge to ground control engineers. Pillar rib sloughs at certain locations, entry width increases in some areas, immediate roof sags, immediate roof rock falls out between bolts, existing bolts lose functionality due to corrosion, cutters develop deeper in corners, and strata separation develops deeper up into the main roof. As a result, unexpected roof falls occur in a random manner resulting in loss of production, damage of belt structure, and even injuries to underground personnel."

Jan 1, 2017

By Zbigniew Lubosik, Andrzej Walentek, Stanislaw Prusek, Sylwester Rajwa, Aleksander Wrana

"Underground coal gasification (UCG) provides a solution to supply electricity from high ash coal or deep deposited seams. The coal is consumed in situ, and, accordingly, the ash is left underground. UCG could play a major role in the future of coal, which is expected to fuel 44% of the world’s energy in 2030, in a more environmentally friendly and commercially viable manner. Nevertheless, it is known that the UCG can impact the environment. One of the most important factors in safe UCG process should be the evaluation of rock mass quality and the monitoring of its behaviour. The changes of rock mass parameters and quality have an influence on numerous aspects, such as subsidence and the stability of underground workings in georeactor vicinity, however, they also increase the possibility of pollutant migration through fractures and pores. These issues are especially important in cases of gasification conducted in an operating mine or on areas of high ecological vulnerability. This paper details observations made in two underground trials of UCG performed in Poland recently. The first of which is the Experimental Mine Barbara (under the project entitled HUGE-2 Hydrogen oriented underground coal gasification for Europe – Environmental and Safety aspects, (Wiatowski et al., 2015). The other trial has been conducted at an operating mine, Wieczorek, which is in the framework of a research project on the development of coal gasification technology for highly efficient fuel and electricity production (Czaplicka-Kolarz et al., 2013). During these trials, investigations were carried out aimed at assessing geomechanical parameters of rock mass and support behaviour in surroundings of UCG geaoreactors. Investigation comprises assessment of geomechanical parameters of coal, floor and roof strata, roof displacements, and concrete support strength parameters variation, as well as standing steel support load. Hydraulic penetrometer, endoscopic camera, Schmidt hammer, pull-out method, telltale, and ground penetration radar (GPR) were used in the investigation. Research conducted at both EM Barbara and Wieczorek Collieries revealed that the UCG process did not adversely affected the competency of rock mass (expressed by number of fissures and strength parameters of rocks), the stability of roadways and the support performance in the areas located in the vicinity of the georeactors."

Jan 1, 2017

By Gennaro G. Marino

As part of the development of a shopping center in West Virginia, a significant bench had to be cut into a mountainside that was over 700 ft. high. As a result, a steeply stepped, over 400-ft.- high wall was created. The high wall exposed old abandoned room-and-pillar coal workings at the toe of the cut. Because of exposure to the elements, the mine openings began to severely deteriorate with significant potential of undermining of the rock cut face and causing a large rock fall(s). Exacerbating this wall problem was a set of fairly planar sub-parallel and sub-vertical joints creating, in essence, thin rock slabs. Also present were stress relief fractures that were observed in the exposed pillars. Given the proximity of the project building to this high rock face, mitigation of the rock fall potential was deemed necessary. In order to prevent continued damage and deterioration of these exposed mine entries, the rubblized openings were filled with bulkhead grout and pressure injected with grout. The total amount of grout installed in these openings was about 3,945 CY. Also, a rock drape was attached to the entire face to mitigate small rock falls from natural causes. There also existed another level of mining below the ground surface and under an existing building at a depth of about 160 ft. Under a portion of the building, the pillars in these old works were second mined, and the building seemed to have been already affected by limited subsidence above this area. Also, calculated pillar safety factors in this high extraction section of the mine were too low. Consequently, these old works were stabilized by saturation grouting. An indication of overall roof distress was the significant fracturing encountered in the bedrock overburden during the drilling of the injection holes and the volume of grout placed in these holes. The total grout installed in the high extraction section of the lower mine was about 6,660 CY. This paper describes the investigation and the grouting techniques employed at the rock cut face and under the existing building to mitigate continued damage to avoid future subsidence problems at the face and the building premises.

Jan 1, 2013

By James D. Pile

Following a methane ignition in the active panel of a longwall coal mine, the affected panel was successfully isolated from the rest of the mine. This allowed for the remainder of the mine to return to regular operation, and the conventional practice of having to seal the portals for a defined period of time was avoided. After the affected panel had remained isolated for a regulatorily mandated period of time, it was reopened in preparation for longwall face recovery. As it was not possible to move the shields from their existing positions to facilitate the installation of recovery mesh prior to shield recovery, alternative methods had to be considered to stabilise the gob and minimise flushing, thereby improving operator safety. The objective of the paper is to show how stabilisation of the gob was achieved during shield recovery, thereby minimising flushing, and improving operator safety. Phenolic foam was chosen and injected from between the shields into the gob behind them. This is a technique that has been used to great effect in Germany, to a lesser extent in Australia, but not knowingly to date in the United States. To ensure nothing was left to chance and thereby guarantee the project?s success, the procedure used in Germany was employed, down to the application of equivalent hardware, which was sourced through the North American supplier.

Jan 1, 2013

By Kousick Biswas

The main objective of occupational health and safety research is to minimize or eliminate the events that may cause fatal or non¬fatal injuries to human workers. A commonly used technique is to devise an "incident prevention plan", which is more often the product of thorough investigations of past reported incident events. Incident documentation and methodical reporting and systematic and thorough data collection, often help identify the root cause of the incident - in other words, the etiology of the incident. These retrospective analyses of the incidents can efficiently identify the future steps to take to achieve the objective of minimizing occurrence of "events of interest". This paper introduces a novel technique - "Taxonomic Analysis", which identifies the root causes of an event (an incident in this case) and can provide future direction for corrective measures to reduce the probability of occurrence of the event. A taxonomic analysis involves systematic and organization of data based on observation, description, and classification. This paper utilizes the rock fall related incident narratives, available with the Mine Safety and Health Administration (MSHA) database (1984¬1999), for a taxonomic analysis. The study found that 67.6% of groundfall incidents occurred in supported areas with the remainder (32.4%) in unsupported areas. Some form of rock mass failure appears to cause about 50% of groundfall incidents, although in 39.7% of the overall groundfall incidents or two-thirds of those involving rock mass failure, the exact nature of the rock mass failure could not be determined from the narratives. Human activities factors such as scaling or barring down, drilling or bolting, and setting timbers or cribbing accounted for another 34.5% of the groundfall incidents. Finally, support system failures made up the remaining 15.5%. Results from this taxonomic analysis may suggest focus areas toward which preventive measures and future research activities could concentrate.

Jan 1, 2003

By Jimin Su, Enguang Zhu, Kangning Zhang, Yang Li

"The effect of interburden on overlying strata movement during the mining of a lower group coal seam is still a challenge in China. Based on the multiple coal seams in western China, numerical simulation and field tests are applied to study the interburden and overburden movement during the undermining process. This study focuses on the impact of the thickness and structure of the interburden, the proportion of hard rock, and the ratio of the overburden thickness to interburden thickness (OB/IB). In this paper, four typical underground coal mines are simulated for lower seam longwall mining with different interburden parameters. The results indicate that the ratio of the overburden thickness to the interburden thickness is not the dominant actor for multiple seam longwall mining, especially in the mines in western China,which feature shallow depth. The thick and hard interburden could strongly affect the lower coal seam mining process. INTRODUCTION The project background is based on four typical underground coal mines in western China.The information on the overburden and interburden is shown in Table 1. Different overburden to interburden thickness (OB/IB) (Ellenberger, 2009) values of the four coal mines are also studied: 6.2 in Bulianta coal mine, 7.2 in Kaida coal mine, 8.2 in Shigetai coal mine, and 9.4 in Halagou coal mine. The proportions of hard rock in the interburden of the four coal mines are also different: 0% in Kaida coal mine, 70% in Shigetai coal mine, 80% in Bulianta coal mine, and 100% in Halagou coal mine. To be specific: the thickness of interburden are listed as follows: 7m in Halagou coal mine, 6m in Kaida coal mine, 10m in Shigetai coal mine, 28m in Bulianta coal mine. The depth of the upper coal seam are: 66m in Halagou coal mine, 54m in Kaida coal mine, 79m in Shigetai coal mine, 182m in Bulianta coal mine. NUMERICAL SIMULATION UDEC 4.0 is applied in this paper to analyse the overlying strata movement and the interburden failure.(Liu, 2007) This is based on mining in the lower coal seam under the mined-out upper coal seam (Majdi, 2012, Morsy, 2006)."

Jan 1, 2017

By Christopher Mark

Current longwall pillar design methods are based on many assumptions about pillar and entry response to longwall abutment loads. Knowledge of the magnitude and time-of-arrival of abutment loads is essential for Improving design procedures. The abutment loads are in turn related to the development of yield zones and horizontal confining stresses in pillars. Entry stability, which is the goal of any longwall pillar design, is affected by in situ stresses as well as the interaction between the roof, pillars, and floor. The paper describes a study performed in a longwall panel at a West Virginia coal mine. The behavior of two headgate pillars and the adjacent entries was- monitored as the longwall face approached and moved past. The results provided a detailed picture of the response of long- wall pillars and entries to abutment loadings.

Jan 1, 1986

By Michael Gauna, Christopher Mark

"Coal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. Despite decades of research, the sources and mechanics of these events are not well understood, and therefore they are difficult to predict and control. Experience has shown, however, that certain geologic and mining factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present, and then identifying appropriate control measures to mitigate the hazard. This paper summarizes the U.S. and international experience with coal bursts, and describes the known risk factors in detail. It includes a framework that can be used to guide the risk assessment process.BACKGROUNDCoal bursts involve the sudden, violent ejection of coal or rock into the mine workings. They are almost always accompanied by a loud noise, like an explosion, and ground vibration. Bursts are a particular hazard for miners because they typically occur without warning. During the years 2012-2014, serious coal bursts occurred at three different U.S. room and pillar mines. These events resulted in three fatalities and two permanently disabling injuries (MSHA, 2014; MSHA, 2013). In all three instances, the events occurred during pillar recovery at depths exceeding 1,000 feet (300 m). None of these three mines had previously reported a burst to MSHA. Coal bursts also occurred at three longwall mines during this same time period.Despite decades of research, the sources and mechanics of bursts are not well understood, and therefore these events are difficult to predict and control. Experience has shown, however, that certain risk factors are associated with an increased likelihood of a coal burst. A coal burst risk assessment consists of evaluating the degree to which these risk factors are present. In addition, some control techniques are effective in reducing the likelihood of an event or protecting miners from their effects."

Jan 1, 2015

By Dongsheng Zhang, Xufeng Wang, Wei Zhang, Gangwei Fan

"Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately in Northwest China, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mining-induced fractures in overlying strata and its relationship to upper aquifers is critical. In this paper, the application of the geophysical-chemical properties of radon in mining engineering is explored as a potential solution to the shortcomings of existing surveying methods. A radioactive measurement method is proposed for the detection of the development of mining-induced fractures in overlying strata in the Baoshan Coal Mine (BCM). The on-site trial indicated that the first weighting step is approximately 60 m, the average periodic weighting step is approximately 20 m, and the influence coverage of the advanced abutment pressure is approximately 30 m. The presented method could be used as an indirect technical support to increase the safety of coal mining by acting as a simple, fast, and reliable method of detecting mining-induced fractures in overlying strata.INTRODUCTIONAccording to the latest coalfield prediction results provided by China’s National Administration of Coal Geology (CNACG) (Zhou et al., 2013), China’s coal resources are mainly distributed throughout the West, e.g., Inner Mongolia, Xinjiang, Shaanxi, Shanxi, Ningxia, and Guizhou. Two major coal mining areas have been established in the Northwest and the Southwest, and are typically represented by Inner Mongolia and Guizhou (Zhang et al., 2010). Northwest China is an arid to semi-arid area, where the coal seams are typically shallow and covered by a thin layer of bedrock. In its natural state, the surface’s ecological environment is fragile. Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. This can propel any potential ecological fragility into a state of actual destruction (Zhang et al., 2011). Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mininginduced fractures in overlying strata has become the theoretical basis of solving the above issues."

Jan 1, 2015

By L. Z. Wojno

Tunnels in South African gold mines are developed at depths down to 3 600 m below surface where the virgin rock stress approaches 100 MPa and, on occasions, through rock where the field stresses exceed 150 MPa. In addition, many tunnels are subjected to increases in field stress of over 50 MPa during their useful lifetime. As a consequence, the walls of most tunnels are fractured causing the rock to dilate into the tunnel. Quantitative data on the extent of this fractured zone are presented. The function of support in these circumstances is to reinforce and maintain the integrity of the fractured rock. In 80 per cent of the 800 km of tunnels developed annually, the support methods used are capable of maintaining the stability of the tunnels. However, the remaining 20 per cent of tunnels is subjected to severer conditions where dilation in excess of 250 mm occurs and/or where the probability of strong seismic ground motion is high. In these tunnels, additional support is required. The type and pattern of support for both normal and severe conditions is described. In spite of the improved support used, damage to tunnels may occur. To minimize this damage, the concept of a rock reinforcing tendon that will yield and do work, when subjected to quasi-static or rapid deformation, has been put forward. Specifications for such a tendon are presented and the development of certain yielding tendons are described.

Jan 1, 1987

By Zhengdong Liu, Kaizhong Zhang, Zhaonan Jiang, Yuanping Cheng, Biao Hu, Qingquan Liu, Ranpeng Wang

"Major coal mining areas in eastern China have entered into the deep mining state. Gas pre-drainage, which has been successful at shallower depths, is not suitable at greater depths because of complex conditions. Coal permeability, which is closely related to the damage behavior of coal, is the most important parameter in determining gas migration and gas drainage in a coal seam. To achieve an optimal gas drainage design in a deep mining state, the damage and permeability evolutions of coal should be further studied. The progressive failure process of coal has been analyzed by conducting a series of triaxial loading and unloading tests. The development of coal fractures has been successfully quantified, and the corresponding characteristic stress points have been obtained by using Martin’s fracture model and the stress-strain curve. Coal will produce plastic deformation, and its permeability will rapidly increase when the stress level reaches damage expansion stress. INTRODUCTION Coal mine methane (CMM) is a general term for all methane released during and after mining operations. CMM is both a potentially valuable energy and a serious hazard in active coal mines. Degassing coal seams is important for mitigating this hazard and results in the beneficial recovery of a cleanburning, low-carbon fuel resource (Karacan, Ruiz, Cotè, and Phipps, 2011). The permeability of coal is a key parameter in determining CMM production, coalbed methane (CBM) production, CO2-enhanced coalbed methane (CO2-ECBM) production, and CO2 storage in coal seam reservoirs (Connell, Lu, and Pan, 2010; Chen et al., 2011; Perera, Ranjith, and Choi, 2013). Significant research has been condcuted to the study of the evolution of coal permeability. These studies revealed that coal permeability evolution is controlled by the competing influences of effective stress and sorption-induced coal deformation. Chen et al. (2011) investigated the influence of an effective stress coefficient and sorption-induced strain on the evolution of coal permeability. Robertson and his team (Robertson, 2005; Robertson and Christiansen, 2005) measured sorption-induced matrix strain and permeability changes with regard to CO2, CH4, and N2. They found that the compressibility is not constant in a natural coal sample. Karacan (2007) conducted a series of experimental tests to study the swelling-induced volumetric strains internal to a stressed coal associated with CO2 sorption. Liu et al. (2016) investigated the effects of matrix swelling area propagation on the permeability evolution by using both natural and reconstituted samples. Many coal permeability models have been developed to describe the permeability evolution under uniaxial loading, biaxial strain, hydrostatic confining pressure, triaxial strain, and triaxial stress. Recently, some analytical permeability models have been developed to describe the anisotropic permeability behavior (Palmer, 2009; Pan and Connell, 2011; Robertson and Christiansen, 2005; Wang, Zang, Wang, and Zhou, 2014; Chen, Pan, Liu, and Connell, 2012)."

Jan 1, 2017

By Denise Y. Dixon

The objectives of this study were to (1) document the hydrologic impacts of longwall mining on ground water, (2) identify the factors which affect the extent of dewatering, and (3) develop empirical trends to predict the extent of dewatering and recovery in advance of mining. The study was confined to three mine sites in north-central West Virginia. At each site, available ground water supplies were identified and monitored for dewatering effects and recovery. Mine A, located in Upshur County, West Virginia, has relatively thin overburden (approximately 715-280 feet). At this site domestic water supplies and specially constructed monitoring wells were monitored, continuing with an earlier study done by Cifelli arid Rauch. Most such supplies were completely dewatered over the longwall panel. Some of these wells have shown significant recovery, especially near a stream. Extensive monitoring of two nested piezometer wells revealed that dewatering generally started in advance of undermining in the lowermost monitored overburden zones first and then progressed upwards. Most dewatered wells completed in bedrock have shown no recovery, except. for valley drilled wells located within 100 feet of a Stream. Affected dug wells completed in valley alluvium rend located within 200 feet. of the nearest stream have shown significant recovery. Some wells have partially collapsed following mine subsidence. Mine B, having relatively thick overburden (approximately 585 to 900 feet), is located in Monongalia County, West Virginia. Ground water supply surveys have been conducted there in an attempt to study past dewatering effects. Owners reported Chat several wells were dewatered by longwall mining arid vertical air shafts that preceded longwall mining. Dewatered wells over longwall panels hove shown some recovery within 3 ½ years of mining. Mine C also has relatively thick overburden (approximately 585-900 feet), and is located mostly in Greene County, Pennsylvania. In addition to a survey of domestic water supplies at this site, five specially constructed monitoring wells were tested. The shallow monitoring wells suffered drops in water level due to mining but totally recovered within one day to three weeks after dewatering occurred. However, they did occasionally exhibit partial collapse during mine subsidence. Subsidence fracturing was beneficial in increasing the lateral hydraulic conductivity by a factor of about S to 22 for rock strata located within 124 feet of the surface, indicating enhanced shallow aquifer potential. One deep well suffered both partial dewatering and structural damage, with the state of water recovery bring uncertain. Also, two shallow domestic supplies out of five located over the mine were reportedly dewatered, but this claim could not, be substantiated.

Jan 1, 1988

By William J. Schloemer

INTRODUCTION The history of coal mining the Ostrava Region of the Czech Republic goes back nearly 250 years. Both coking coal for steelmaking and thermal coal for the production of energy are mined here; however, it was the coking capabilities that subsequently turned the region into a major steel-producing area in the early 1800?s, something that continues to this day. Ostrava lies in the northeast corner of the Czech Republic, near the southern border of Poland, and falls within the Upper Silesian Coal Basin. The region contains over 400 seams of coal of which about 150 have been mined over its history and continue to be mined. Eighty percent of the Upper Silesian coalfieldlies in Poland and is presently mined by about 35 coal mines; the remaining 20% falls in the Czech Republic, which presently has four mines operated by OKD, a.s., a subsidiary of Amsterdam-based New World Resources. Traditionally, all the mines in this region have employed the longwall method of mining, of which subsidence is an unavoidable consequence. In fact, due to the long history of longwall mining here, there are areas where the overall subsidence has exceeded 37 meters (121 feet). The region is fairly densely populated with residences and industry, and a considerable amount of coal lies under some of these areas where subsidence is not allowed or has to be minimized. It is this reason that has driven OKD to consider alternate methods of mining that will not create subsidence. The decision was made to consider the room and pillar method of mining in order to leave stable pillars of coal to support the surface. After considering several locations, OKD chose the shaft safety pillar at the CSM mine as a test mining location. To say the least, this is a very challenging location in which to conduct a test. As with the entire region, there are many faults from tectonic activity, the seams are pitching at 12 to 20 degrees, the area is affected by high horizontal stress, and the depth of 750 to 900 meters is perhaps the deepest room and pillar coal mining ever attempted.

Jan 1, 2014

By Bingjie Huo

"China is a major coal producer and consumer. It is necessary to mine the steeply pitching coal seams due to development of the coal industry to meet the increasing needs for coal. Flexible shield supports mining is a safe and efficient mining method for steeply pitching coal seam that was first applied in HuaiNan mining area in the 1970s. The coal seams are steeply pitching in DaAnShan Colliery, so mining is mainly done by the flexible shield supports method. The roadway lay-out and extraction technology are researched in order to improve the safety, yield and work efficiency in the flexible shield supports working face. Optimization of the flexible shield supports mining method is discussed. The main optimization aspects are as follows: (1) the angle of working face and mining track roadways are increased from 23° to 28°, and (2) the technology and parameters of coal breaking are optimized. Applicable conditions, as well as advantages and disadvantages are also discussed. Finally, a comparison is made of the two different flexible shield supports mining methods, namely ""bench blasting . technology"" and ""piecewise blasting technology"".INTRODUCTIONChina is the largest producer and consumer of coal in the world and relies heavily on coal for energy production. At present, Chinese production is about 42% of the worldwide production, and coal has accounted for 76% of primary energy production. Coal plays a dominant role in the structure of energy production and consumption, which is fuel and an important industrial raw material but it is non-renewable. In recent years, the high inclined seams (35°< angle of coal seam < 45°) and steeply pitching coal seams (angle of coal seam >45°) have drawn increasing attention in the mining sector along with the growth of coal mining. There are two reasons. First, there are abundant reserves of high inclined and steeply pitching coal seams in China, which account for 15- 20% of total reserves (Xie, Dong-hai, 2007). Highly inclined and the steeply pitching coal seams are mined in more than 50% of the western mining provinces such as Sichuan, ChongQing, YunNan, GuiZhou, XinJiang, GanSu, NingXia, etc. As the mining of mineral resources continues west in the 21st century, the study of coal mining in high inclined seams and steeply pitching coal seams will be of great importance. Secondly, better quality coal has become scarcer in the eastern mining areas after years of exploitation, so steeply pitching seam mmmg is growing more prevalent. In short, carrying out research on steeply pitching seam mining technology plays an important role in sustaining the development of the Chinese coal industry."

Jan 1, 2010

By Jonathan Duncan, Tim Burgess, William Kendall, Jens Lange

"Steel wire mesh is the accepted standard for roof and rib skin control at most coal mines in the United States. Wire mesh is delivered to the mine in bundles that are heavy and awkward to handle. The large size, stiffness, and weight of the wire mesh can present a safety hazard in transporting underground and storing on the roof bolter. Installing wire mesh on the roof and ribs with the roof bolter can be a challenge as well.Synthetic mesh is lighter than wire mesh and can be folded and rolled into a safe, manageable size. A single synthetic mesh roll large enough to cover the roof and ribs in a deep cut can be safely handled by two men. The roof bolter is designed to carry and dispense the roll as it advances and installs primary roof support, resulting in a single pass roof and rib ground control solution. This paper focuses on the design and implementation of the roof bolter synthetic mesh handling system developed by J. H. Fletcher & Co., Huesker, Inc., and Oxbow Mining.INTRODUCTIONRoof and rib skin control in some coal mines has been an issue since mining first began. Roof and rib skin problems vary from mine to mine. The type of roof rock material exposed after mining; the mine atmosphere; and stresses from depth of cover, over mining, and/or undermining are some of the variables that can contribute to roof skin problems from mine to mine.Potential roof and rib skin problems can be time dependent as well. Some mines have roof skin rock, sometimes called draw rock, that falls when drilling the hole for the roof bolt as the initial roof support is installed. Some roof skins are more stable but can fail over time. The failure of roof skin can even be between properly installed roof bolts with roof plates (Figure 1).Mines have most commonly used a wire mesh that comes in individual panels anywhere from 5 ft x 5 ft (1.5 m x 1.5 m) all the way up to 5 ft x 16 ft (1.5 m x 4.9 m) in size. They are typically constructed of 8- or 9-gauge wire welded on a 4 in (102 mm) square pattern. A 5 ft x 16 ft (1.5 m x 4.9 m) panel weighs approximately 35 lbs (16 kg). These steel wire mesh panels can make it a difficult and sometimes dangerous task to deliver them from the surface to the roof bolter and then store on the machine. Manipulating the mesh panels from the storage area on the machine to the final installation position on the roof or rib can also be a daunting task (Figure 2)."

Jan 1, 2010

By Mark K. Larson

Panel-scale modeling of stress changes induced by longwall coal mining is a challenging problem, particularly in deep mines of the western United States. Two common approaches to this problem are the empirical and boundary element modeling methods. One boundary element method, LaModel, was recently calibrated to field measurements at a mine in Colorado (Larson and Whyatt, 2012). However, the calibrated overburden properties were extreme, resulting in very low estimates of gob loading. Next, the empirical method was calibrated to field measurements and applied to the problem, but this approach clearly extrapolated this method well beyond the characteristics of underlying cases. This paper examines a third option, the elastic continuum boundary element program Mulsim. The program was expanded to handle LaModel-size meshes in a version dubbed Mulsim/ Large. Properties for the elastic, homogeneous overburden model in Mulsim were estimated as a thickness-weighted average of typical published elastic properties for each major stratum. These properties, along with a commonly used pillar strength equation and coal properties, produced the measured load transfer distance and reasonable gob loading without further calibration. Given the number of input parameters required for all of these methods, it is not surprising that LaModel and the empirical approach could be adjusted further to incorporate similar gob loads. However, these extraordinary measures failed to bring gate road pillar loading in line with Mulsim results. Differences in pillar load estimates continued to be significant (as large as 65% in this study). These results demonstrate that, for this particular case, the choice of analysis method impacts results in ways that cannot be removed by calibration of input parameters. Finally, the natural fit between the Mulsim model and mine conditions suggests that approximating overburden at the particular site used for this research as an elastic continuum is superior to the alternatives examined.

Jan 1, 2013

By Peng Zhang

In a recent research effort, a laminated overburden loading model (as implemented in LaModel3.0 was compared with the results of ARMPS 2010, and the laminated overburden model was found to more accurately classify a ARMPS database of 52 deep cover case histories by a factor of 60% versus 54%. However, the LaModel analysis of each case study required several days to complete, as compared to a requirement of only several minutes for each ARMPS analysis. In the research presented in this paper, a computer code (ARMPS-LAM) has been developed to effectively implement the laminated overburden model into the ARMPS program. This program takes the basic ARMPS geometric input for defining the mining plan and loading condition and then automatically develops, runs, and analyzes a full LaModel analysis of the mining geometry to output the stability factor on the Active Mining Zone(AMZ), all without further user input. The present laboratory version of ARMPS-LAM can be run in batch mode; therefore, the ARMPS 2010 database of 645case histories can be analyzed very quickly. In an initial logistic regression analysis of this database, the ARMPS-LAM program was seen to be slightly more accurate than ARMPS 2010 by a factor of 71% versus 63%.

Jan 1, 2013

By David F. Gearhart, Mark Van Dyke, Heather Dougherty, Ted Klemetti, Gabriel S. Esterhuizen

"Coal mine longwall gateroads are subject to changing loading conditions induced by the advancing longwall face. The ground response and support requirements are closely related to the magnitude and orientation of the stress changes, as well as the local geology. This paper presents the monitoring results of gateroad response and support performance at two longwall mines at a 600-ft and 2,000-ft depth of cover. At the first mine, a three-entry gateroad layout was used. The second mine used a four-entry, yield-abutment-yield gateroad pillar system. Local ground deformation and support response were monitored at both sites. The monitoring period started during the development stage and continued during first panel retreat and up to second panel retreat. The two data sets were used to compare the response of the entries in two very different geotechnical settings and different gateroad layouts. The monitoring results were used to validate numerical models that simulate the loading conditions and entry response for these widely differing conditions. The validated models were used to compare the load path and ground response at the two mines. This paper demonstrates the potential for numerical models to assist mine engineers in optimizing longwall layouts and gateroad support systems.INTRODUCTIONThe need for roof stability in coal mine longwall gateroads places significant demands on the gateroad ground support system. The variable loading conditions associated with the approaching longwall face can cause excessive ground deformations that need to be accommodated by the support system. In coal mines in the United States several different types of supports are used to maintain the stability of gateroads. The supports may include grouted roof bolts, cable bolts, and roof trusses as intrinsic support. Standing supports include timber cribs, engineered timber props, and various types of cement-based cribs. The intensity of support is governed by the expected geologic conditions and the expected stress changes that will occur during longwall mining. At present, the design of ground support for gateroads is largely based on local experience. In-mine trials are usually conducted when new support technologies become available or ground conditions dictate a change in the support system. The research reported in this paper has the objective to assist mining engineers in evaluating alternative gateroad supports and to design suitable support systems for the local ground conditions."

Jan 1, 2018

By Yuanfei Chen, Jianfeng Zha

"China is the largest producer and consumer of coal in the world. The mining-induced surface subsidence has bad influences on the surface and structures above the surface. In order to minimize disasters, removal, reinforcement, or maintenance structures are often adopted. In the application of maintenance methods, it is necessary to carry out dynamic surface subsidence prediction to choose maintenance methods, optimize maintenance time, and evaluate the amounts of work. Time series methods and influence function methods are common for dynamic surface subsidence prediction, but the former is difficult to consider with underground mining conditions, and the latter has low prediction precision. Therefore, this paper develops a dynamic subsidence prediction model aided by field-measured data and realizes the model programming. The model could achieve high-precision prediction of dynamic surface deformation through optimizing the parameters in time by using field-measured data of surface subsidence. The research results of engineering cases show that, with the method of dynamic prediction, the standard error can be controlled in the range of 5%, greatly improving the accuracy of dynamic prediction of mining subsidence, which provides strong technical support for the maintenance and management of structures. INTRODUCTION With the rapid economic development and continued industrialization process, the demand for energy is growing in China. Today, China is one of the largest coal, oil, and gas consumers in the world. Coal consumption accounts for 47.7% of the total consumption in the world (Tian, 2016). In order to meet the demand for coal resources in the process of modernization, more and more coal mines carry out coal mining under villages, buildings, highways, and bodies of water. The mining-induced overlying strata and surface subsidence have bad effects on surface and on various structures (such as buildings, railways, highways, high-tension transmission lines) and could even cause various disasters (Williams et al., 1998; Bell et al., 2000; Doyle et al., 2002). Generally, methods, such as removal, reinforcement, or maintenance are taken to eliminate the adverse impacts (Kraatz, 1984; Bell and Genske, 2001; Wang, 1989). When reinforcement or maintenance is selected to remove bad effects, the proper maintenance methods must be chosen. In addition, maintenance time, as well as an evaluation of time it will take to do the work are necessary to predict the surface subsidence with high precision."

Jan 1, 2017