Search Documents

Council for 2003/2004 President T.R. Stacey President-elect F. M. G. Egerton Vice-presidents Senior W. H. van Niekerk Junior R.P.H. Willis Immediate Past-president S.J. Ramokgopa Honorary Treasurer J.A. Cruise

Jan 1, 2004

By S. M. Bradshaw

The principles of microwave heating are discussed with reference to dielectric properties, heating phenomena and microwave equipment. Microwave regeneration of granular activated carbon for the carbon-in-pulp process is examined on a laboratory scale, with special attention being given to highlight the problem areas and specific considerations related to microwave heating. Results indicate that microwave regeneration of carbon with 40% moisture on a wet basis by heating to 650°C with steam addition regenerates the carbon to virgin carbon activity levels but with a higher abrasion resistance. A preliminary economic assessment showed that the capital cost for 120 kg/h microwave unit would be R540 000 with an annual operating cost of R 320/t carbon. These figures yield a return on investment of 12%. The aim of this paper is to provide an introduction to microwave heating and to illustrate its application to the microwave regeneration of granular activated carbon for the carbon-in-pulp (CIP) process.

Jan 1, 1998

This paper addresses the methodology of introducing risk into the development of mine plans for open pit mines. Recommendations are put forward for achieving a risk balance between mineral resource estimates and slope design. A design process identifying criteria for different stages of planning is presented. Business risk is separated from geological/geotechnical risk and procedures to address these within the development of mine plans are suggested. It is concluded that a formal design process improves communication between key decision makers and adds value to shareholders, investment.

Jan 1, 1997

By FJ Fourie

This paper describes the concept and development of the use of a uni-delay shock tube system in the timing and initiation of the development rounds, specifically in flat development. It was extended from stoping and now constitutes the only initiation system is use at Kopanang mine. The two explosives initiation systems in general use in underground mines are the conventional fuse-igniter cord system, and the more modern Long Period Delay shock tube system, better known as the numbered LP system. Both are well accepted but have many drawbacks which can result in poor breaking and substantial wastage of the blasting material. Both of these deficiencies cause an increase in the cost of a blast. Hitherto, the limited number of delays available has complicated the use of shock tubes in development blasting. Over eighteen month period to the end of 2007, a project team comprising members from Kopanang Mine and AEL developed a method for the use of a uni-delay shock tubes to time any development round. These uni-delay shock tubes are better known as Reef Masters® or EZ-Stopers® depending on the supplier, and the system has particular application in flat development. During the project, two new shock tube system components were designed, tested and manufactured; namely Splitters and Starter Packs. The system has been successfully tested and implemented in both on-reef and off-reef development ends. At Kopanang, it has now been rolled out across the entire mine. Other AnglogoldAshanti mines are conducting trials and implementations into production sections. Initial results indicate improvements in the ground conditions and excavation profiles. The cost of blasting is showing a downward trend. The authors consider that the system is a tool for use in further blast optimization and will contribute to rationalization of the explosives commodities basket on mines.

Jan 1, 2008

By Jeremy Bosman, Johan de Korte

Traditionally the feed to coal preparation plants was de-slimed at 0,5 mm. The +0,5 mm size fraction was processed via dense-medium cyclones and the -0,5 mm size fraction was beneficiated with froth flotation, water-only cyclones or spirals. With the introduction of large diameter cyclones, the aperture sizes of de-sliming screens have progressively increased to about 3 mm in the belief that the larger cyclones are not able to effectively beneficiate coal which has a particle size below the ?breakaway? size. The efficiency of separation in the large dense-medium cyclones is improved by presenting a coarser feed to the units. At the same time, the capacity of the de-sliming screens is increased due to the larger screen apertures and in effect, the throughput capacity of the dense-medium section is increased. The 3 x 0,5 mm size fraction, which was previously processed in the dense-medium cyclones, is now added to the fine coal size fraction and processed by water-only methods such as Teetered Bed Separators (TBS) and spirals. Whether this practice is the most economical way to process the 3 x 0,5 mm size fraction requires further thought since the best processing route for the 3 x 0,5 mm size fraction will depend on a number of factors, amongst which are: o The washability of the coal and the amount of near-density material o Processing efficiency o Specification of the required product o The price paid by the customer for the product o The cost of processing the coal Breakaway size The ?breakaway? size is defined as the particle size below which the Epm of the smaller particles starts to decrease significantly. Bosman1 provides an approximate breakaway size versus cyclone diameter (Figure 1). It should be kept in mind though that the Epm of the small particles is a function not only of the cyclone diameter but also of feed pressure, medium density, medium viscosity, particle shape and density, top-size of particles in the feed, etc.

Jan 1, 2006

A physical modelling study has been carried out to simulate the slag-metal dispersion induced by a high-strength bottom gas injection. Water and kerosene were utilized to simulate metal and slag respectively. A water model of CLU (Creusot-Loire Uddeholm)vessel was used with three different nozzle orientations, namely, off-centre, triangular off-centre and centre. The gas flow rates changed from 0.00599 m3/s to 0.01081 m3/s. Height of heavy and light phases was kept fixed at 0.23 m and 0.02 m respectively. The dispersed phase hold-up was determined at various axial and radial distances, gas flow rates, and tuyere configurations. The observations revealed that at a fixed gas injection rate, as the vertical distance increased in the centerline, straight off-centre orientation resulted in greater dispersed phase hold-up values than those of the centre configuration and the triangular off-centre orientation. The dispersed phase hold-up was found to increase with gas injection rate and decreased with axial distance. The variation of the dispersed phase hold-up with the dimensionless axial distance and the gas injection rate was correlated by using the modified Froude number. The experimental values of the dispersed phase hold-up were found to be in reasonable agreement with the correlated values obtained from the modelling equations. The findings of the present study may be utilized in the ferroalloy refining vessels in terms of designing tuyere locations for optimum processing conditions.

Jan 1, 2004

By J. H. Potgieter

This paper describes an investigation to separate and selectively recover silver, gold and platinum from jewellery and laboratory wastes, and produce technical grade material suitable for training purposes. Nitric acid was employed to dissolve and separate silver and other impurities from gold and platinum, which were then dissolved in aqua regia and precipitated selectively. The current work quantified the effects of temperature, stirring rate, leaching agent concentration and solid: liquid ratio on the recovery of the various noble metals and in summary yielded the optimum treatment conditions in each case. It was found that increased leaching reagent concentration (in the case of Ag), temperatures and stirring rates enhanced the recovery kinetics and optimum yield of the three noble metals. An increased liquid to solid ratio also enhanced the recovery of the silver. Recovery yields 97.1%, 99.9%and 99.4% for silver, gold and platinum, respectively, were obtained. The recovered silver, gold and platinum had purities of, respectively, 98.3%, 99.1% and 99.0%. A cost saving of approximately R10 000 per kilogram of scrap refined could be achieved by the in-house treatment of the waste, not to mention the time-saving benefit.

Jan 1, 2004

By A. J. Lynch

Mineral processing models have been discussed for many years but it was not until digital computers became available about 1960 that serious attempts at circuit simulation could be carried out. Even then the work was primarily academic until PCs could be used by engineers in plants and design offices in the mid-1980s. Since then simulation has moved quickly and it is now at the point that most processes can be simulated reasonably accurately for purposes of design and optimization. There are still some significant deficiencies, notably in dry grinding and separation, and in the chemical interactions in flotation. Future work will involve: ?improvements of existing models ?dynamic simulation for automatic control and, in particular ,for training which is a weak link ?using advanced simulation models to predict liberation and separation from data acquired from SEM-based liberation analysers. Eventually mineral processes models will be part of total simulation systems which will incorporate mining and downstream processes including all environmental impacts.

Jan 1, 1999

By A. Feather

The Minataur? Process (Mintek Alternative Technology for Au Refining) is a novel route for the production of high-purity gold using solvent extraction. Following the successful demonstration of the process on a pilot-plant scale, a full-scale 24 t/a production plant has been commissioned at Harmony Gold Mine in Virginia, Free State. The commercial implementation of this process represents not only a significant advance in gold-refining technology, but may be instrumental in initiating important changes in the legislation regulating the marketing of gold in South Africa. Gold of either 99.99% or 99.999% purity can be produced from intermediate process products having a wide range of gold contents. The process comprises oxidative leaching of the solid feed, followed by selective solvent extraction of the gold from the leach liquor to reject impurities, and precipitation of high-purity gold powder. This paper outlines the process, presents selected results of two pilot-plant trials in which 5 kg/d of high-purity gold was produced from silver-refining anode slime and gold-electrowinning cathode sludge, and provides some details of the cost benefits.

Jan 1, 1997

By A. L. Edwards

A two-year study focused on current noise exposure levels in the South African mining industry, aimed at helping the Mine Health and Safety Council of South Africa meet its milestones for eliminating noise-induced hearing loss (NIHL). Methods A multi-task methodology was adapted from international baseline studies to determine the exposure to noise in both large-scale and small- to medium-scale mines. Results On average, 66.7 per cent of the employees sampled in year 1 and 78.4 per cent in year 2 were exposed to noise levels of above the 85 dB A legislated occupational exposure level. Conclusions Information obtained through the study could be developed into a national personal noise exposure database, including audiometric results, equipment noise emission levels and initiatives for noise engineering control by mines and equipment manufacturers to facilitate targets of eliminating NIHL. Keywords Noise exposure levels, mining industry, noise-induced hearing loss

Jan 1, 2011

By H. J. Ilgner

The paper reviews the results to date of an integrated research programme currently being conducted by CSIR Mining Technology, aimed at impacting significantly on concentrated mining with face advance rates of up to 20 times faster than presently achieved. Consideration is given to the interplay between innovative technologies for continuous non-explosive mining or rock comminution underground and lateral hydraulic transportation in cross cuts, haulages and eventually hydro hoisting. Novel technologies for underground comminution of reef and development waste and an innovative pumping system suitable for the hydraulic transportation of coarse comminuted rock are reviewed. Emphasis is placed on South African gold mine reef and waste samples comminuted by electric shock wave comminution technology. The innovative TORE® pump system appears to be well suited for the successful hydraulic transportation of rock, produced by electric shock wave comminution, at solids concentrations between 45 % and 67 % by mass.

Jan 1, 1997

By S. Jiansheng, H. Nakayama, D. Lu, A. Wang

ABSTRACT: New techniques and methods for 3D geo-mechanical model test are presented in this paper. The new model material NIOS with high density and low cost; the so-called DPSS (Discrete Principal Stress Surface) loading concept, the loading and monitoring system for the generation of the 3D initial stress field of the model test, also the special techniques and apparatuses for modelling the excavation of caverns located deep inside the model material, are developed and introduced. By adopting those new techniques, a very large 3D geo-mechanical model test with high comparability for a newly designed underground powerhouse has been successfully fulfilled. Key Words: 3D model test, underground group caverns, excavation process modeling. ZUSAMMENFASSUNG: Neue Techniken und Methoden für 3D geomechanischen Modellversuch wurden in diesem Artikel vorgestellt. Ein neues Modellmaterial mit hocher Dichte und niedrigem Preis, ein sogenanntes DPSS (Discrete principal stress surface) Ladenkonzept, ein Laden- und Überwachungssystem für die Erzeugung des 3D primären Spannungsfelds und überdies spezielle Techniken und Maschinen für das Ausbruch der tief in dem Versuchsmodell liegenden Kaverne wurden entwickelt. Bei Anwendungen dieser neuen entwickelten Techniken wurde ein sehr großer 3D Modellversuch mit großem Maßstab für ein geplantes unterirdisches Kraftwerk erfolgreich durchgeführt. Stichworte: 3D Modellversuch, unterirdischen Gruppekaverne, Ausbruchsmodellierung Résumé: le test de modèl de Nouvelles techniques et méthodes pour la géo-mécanique 3D est figuré dans ce papier. Le nouveau modèle de matériels NIOS avec la haute densité et le coût bas; la conception proposée de chargement DPSS (Discrete Principal Stress Surface), le système de chargement et de moniteur pour la génération de champs de stress initial du test de modèle, ainsi que les techniques et appareils spéciaux pour modeler les excavations de cavernes profondément localisées dans l’intérieur du matériel de modèle, sont développés et introduits. A travers l’adoptation de ces nouveaux techniques, le test de modèle de la géo-mécanique très large 3D avec la haute comparabilité pour actualiser une nouvelle étude de la centrale électrique sous-terraine a déjà accompli avec succès. Mots de clé: test de modèle 3D, groupes de cavernes sous-terraines, processus de modèle d’excavation

Jan 1, 2003

By S. Lin

A new hydrogen production process, named the HyPr-RING, has been proposed. Fundamental concept of the HyPr-RING is integration of water carbon reaction, water-gas shift reaction and CO2 absorbing reaction in a single reactor. Firstly, thermodynamic analysis was done to judge the possibility to realize the process. It was found that high pressure and temperature condition, such as 20 MPa and 1000 K, is required to promote this integrated reaction. Next, experimental verification of the new process was done under the high pressure and temperature reaction conditions. As the results, integration of above three reactions in a single reactor can be done successfully and produced a large amount of hydrogen as estimated by thermodynamic analysis. Experiments showed that organic materials including coal, heavy oil, biomass, plastics can be used in this process. In the gaseous phase, no pollutants such asH2S, SO2, COS are detected so that gas cleanup system is not required for power generation when this process is used. Finally, a process design was made to estimate process efficiency. Theoretically, 1 mole of carbon can generate 2 moles of hydrogen and cold gas efficiency of this process estimated as more than 80 per cent. The process potentially reduces hydrogen production cost compared with the conventional hydrogen production methods. Keywords: Hydrogen, Fossil fuel, Energy, Process, Supercritical water

Jan 1, 2001

By I. Grigoriev, A. Yolkin, E. Freiberg, A. Fedchun, A. Kolichko

Abstract: The paper describes the engineering-geological conditions and the structural decisions of the underground machine hall of Rogun HPP under construction in Tadjikistan on Vaksh river as well as the results of physical model studies and long-term in-situ investigations of the variation of the stress-strain state of the surrounding rock mass and the supports of openings, and the assessment of the stability of openings during and after the construction. The analysis of the results of long-term in-situ observations and previous model studies permitted to make the assessment of the present-day state of the machine hall and give recommendations of its further use. Zusammenfassung: Im Vortrag werden die ingenieurgeologischen Bedingungen und konstruktiven Lösungen für die unterirdischen Maschinenhalle des in der Republik Tadshikistan am Fluss Wachsch im Bau stehenden Rogunskaja-Wasserkraftwerkes, die Ergebnisse von experimentellen Forschungen (in physikalischen Modellen) und Naturbeobachtungen der Spannungs-Verformungszustandsänderungen des umliegenden Felsmassivs und Ausbaues von Untertagebauten, sowie Ergebnisse der Bewertung der Standfestigkeit von Untertagebauten während des Bauvorganges und nach der Bauperiode beschrieben. Auf Grund der Analyse von Ergebnissen der dauernden Naturbeobachtungen und früher durchgeführten geomechanischen Modellversuche wird der heutige Zustand der Maschinenhalle des Wasserkraftwerkes bestimmt und werden die Empfehlungen für ihren weiteren Benutzung angeführt. Annotation: L’exposé décrit les conditions d’ingénieur et celles géologiques, et les solutions constructives de la salle des machines de la Centrale hydroélectrique (CHE) Rogounskaya sur le fleuve Vakhch, les résultats d’études expérimentales (sur des modèles physiques) et d’observations extérieures sur place concernant des changements de l’état de tension-déformation d’un massif environnant et du cuvelage des excavations, ainsi que les résultats d’évaluation de la stabilité de l’excavation au cours de la construction et à la période post-construction. A la base de l’analyse des résultats des observations de longue durée et des études préalables géomécaniques sur des modèles, l’évaluation de l’état actuel de la salle des machines de la CHE est effectueé, et les recommandations sur son utilisation ultérieure sont présentées.

Jan 1, 2003

Mineral Resource Throughput Management is based on the extraction of the maximum potential value from an ore reserve with the emphasis to generate maximum ROI and ROR (return on reserve). A steel producing company in India implemented MRTM to significantly improve their ROI and ROR. The value chain of this company consists of their own iron ore and coal mines, ore washing plants, sinter plants, steel plants, and sales and marketing division. The target for the mines was to produce at a stable and predictable rate and at specific quality requirements. These requirements were set to improve productivity and ROI of the steel plant. The implementation constituted the alignment of the reserve potential, total production chain, human resources and management culture at the mines with the requirements of the steel plant. Many typical mining practices were challenged and changed. Production targets regarding lump vs. fines ratio, consistent product tons, quality targets such as Fe, Al content and moist, and standard deviation on the quality targets were not achieved. A reverse distribution model with release mechanisms to satisfy the demand were developed and implemented at the mines. A stable and predictable flow of mine product with quality standards well within the required standard deviation targets were achieved. The contribution from the mines to significantly improve the Net Profit, ROI and ROR of the company were reached.

Jan 1, 2007

By J. van Deventer

Testwork was done with two different adsorbents, Dowex-Minix gold-selective resin and activated carbon, to detemine their relative performances with regard to gold recovery from clarified low-grade solution employing a fixed-bed operation. The mill discharge from the milling-in-cyanide operation at a Witwatersrand gold mine was used as feed to the adsorption columns. A small amount of gold was leached during the milling process, so that this solution simulates, to a certain extent, a low-grade solution representative of a heap-leach operation. A speciation of the feed solution was done to establish which metal complexes were present in the milling-in-cyanide solution. This information was necessary to interpret metal loadings on the resin, as base metal cyanide species and their respective charges have an effect on the final gold loading capacity of the resin. Equilibrium isotherms were established for both adsorbents to estimate the rate of adsorbent flow anticipated for this specific feed solution. Breakthrough profiles were obtained at two different superficial linear velocities for each adsorbent. Mass transfer zone heights determined from the test work and the elution/regeneration time requirements were used to size a 150 m3/h full-scale plant for both adsorbents. A counter current configuration of adsorption columns, using three columns, should be suitable to recover gold effectively and to produce an effluent with a gold concentration below 0.01 mg/l. Based on the results obtained from the breakthrough tests, a preliminary techno-economic comparison was done between the resin-in-solution and carbon-in-solution options for the recovery of gold from low-grade solutions. This study indicated that the capital expenditure for a carbon-in-solution plant would be about 33 percent higher than that of a resin-in-solution plant. The operating expenditure for a resin-in-solution plant is expected to be only 60per cent of that for a carbon-in-solution plant. Keywords: resin-in-solution, carbon-in-solution, heap leach.

Jan 1, 2000

By J. B. Oosthuizen

Mechanical rock breakers are used in block caving operations to reduce the size of ore fragments which are too large to pass through grizzlys at the load-haul-dumper tipping points. Several layouts of grizzly, rock breaker and ore pass are possible. The authors evaluated three different layouts at the Premier Mine Division of De Beers Consolidated Mines. The first layout consisted of a 15m surge bin before the breaker, which was located 15 m below the production level. The second layout had a 43 m longs urge bin, with the breaker located 43 m below the production level. The third layout did not have a surge bin, the breaker was located on the production level and operated at the tip. The ore throughput, availability and utilisation, delays, costs and operational experience with each system are discussed. It was found that the rock breakers did not represent a bottleneck in the ore transfer system and a surge bin did not significantly improve the production capacity. The mine has decided to make use of rock breakers situated on the production level, breaking rocks at the tip.

Jan 1, 1997

By P. H. S. W. Kulatilake, B. Malama

To simulate brittle rocks, a mixture of glastone, sand and water was used as a model material. Thin galvanized sheets were used to create joints in blocks made out of the model material. To investigate the failure modes and strength, both the intact material blocks as well as jointed model material blocks of size 35.6 × 17.8 × 2.5 cm having different joint geometry configurations were subjected to uniaxial and biaxial compressive loadings. Results obtained from the intact model material blocks are used to validate a new intact rock failure criterion for biaxial loading. Results obtained from both the intact and jointed model material blocks are used to develop a strongly non-linear new rock mass failure criterion for biaxial loading. In this failure criterion, the fracture tensor component is used to incorporate the directional effect of fracture geometry system on jointed block strength. The failure criterion shows the important role the intermediate principal stress plays on rock mass strength. Zur Simulation spröder Gesteinsarten wurde ein Modellmaterial aus Dentalgips, Sand und Wasser hergestellt. Daraus wurden Blöcke gegossen, in denen mittels dünnen, galvanisierten Blechen Trennflächen erzeugt wurden. Die Blöcke mit Abmessungen von 35.6 × 17.8 × 2.5 cm wurden in einaxialen und biaxialen Druckversuchen belastet. Es wurde das Versagensverhalten und die Festigkeit von intakten Blöcken sowie durchtrennten Blöcken mit unterschiedlicher Trennflächengeometrie untersucht. Aus den Ergebnissen der Versuche an intaktem Material wurde ein neues Versagenskriterium für biaxiale Belastungen validiert. Die Ergebnisse der Versuche an intakten und durchtrennten Blöcken wurden verwendet, um ein neues stark nicht-lineares Versagenskriterium für geklüftetes Gebirge unter biaxialer Belastung abzuleiten. Darin wird der Bruchtensor verwendet, um den Einfluss der Trennflächengeometrie auf die Festigkeit zu erfassen. Das Versagenskriterium stellt heraus, welche Bedeutung die mittlere Hauptspannung für die Gebirgsfestigkeit hat. Un mélange de platre dentaire, de sable et d’eau a été utilisé pour développer un matériau analogue des roches fragiles. De fines feuilles galvanisées permettent de créer des discontinuités représentatives des discontinuités naturelles dans des bloques fabriqués avec ce matériau analogue. Les modes de rupture et la résistance, tant pour le matériau intact que pour le matériau avec ses discontinuités, ont été étudiés sur des blocs de 35.6 × 17.8 × 2.5 cm soumis à des efforts de compression uniaxiaux et biaxiaux. Différentes configurations de géométrie de discontinuités ont été considérées. Les résultats obtenus à partir des blocs intacts permettent de vérifier un nouveau critère de rupture pour les roches intactes soumises à des efforts biaxiaux. Les résultats obtenus, tant avec les blocs intacts qu’avec les blocs avec discontinuités, sont utilisés pour développer un nouveau critère de rupture, fortement non linéaire, pour les massifs rocheux soumis à des chargements biaxiaux. Dans ce critère de rupture, un tenseur de fractures est introduit pour caractériser les effets directionnels de la géométrie des systèmes de discontinuité sur la résistance des blocs avec discontinuités. Ce critère de rupture démontre le rôle important de la contrainte principale intermédiaire sur la résistance des massifs rocheux.

Jan 1, 2003

By I. Benning

Since the dismal performance of the Rand Mines management was called to account by its shareholders in 1994, the waves of change have continued to ripple across the South African mining industry .The number of listings on the gold board of the Johannesburg Stock Exchange, that once numbered 40 or 50-odd, have now dwindled to no more than a handful as unprecedented restructuring has taken place. The redefining of the industry has not been limited to the gold sector, but across the base metal, coal, diamond, platinum and industrial mineral sectors as well. At the same time the Mining Houses began to reconsider their funding strategies. Originally established in the early part of the century to ensure the long-term sustainability of their group mining operations by providing substantial financial muscle and technical support, the Mining Houses were faced with a rapidly changing political environment, which proved to be a critical catalyst in giving momentum to the change. Furthermore, the significant development costs and increasing risk profile for new projects, coupled with pressure from shareholders demanding respectable returns, opened the door to opportunities for banks to begin providing external debt by the way of project finance. However, the provision of long-term debt to the South African mining industry had generally not been common since mining companies had financed new projects with equity, or with the cash flows from existing operations. Those banks that had the appetite for exposure to the perceived high risks of the mining sector rapidly built up specialist resource banking divisions capable of addressing the increasing demands of the industry. The application of project finance, the principles of which were developed in the 1970s specifically for infrastructure projects and privatization, is now commonly applied in the financing of greenfield and brownfield mining projects. This paper outlines the approach that lending banks would typically adopt when arranging or providing mining project finance, their usual areas of concern and the way in which the finance is structured to mitigate the many inherent risks.

Jan 1, 2000

The EMEM Awards of the Department of Minerals and Energy (DME) were formally launched on 3 March 2000 by Ms Susan Shabangu, Deputy Minister at the Department?s Mineralia Centre in Pretoria. The launch was attended by invited guests from the mining and aggregate industries ,representatives of the Patron Organisations (see below),non- government and scientific organizations, the media, other government departments involved with mining environmental management and members of staff of the DME both nationally and regionally.

Jan 1, 2000