Search Documents

By J. P. Josien, Didier C.

ABSTRACT: France now faces the closure of most of its mining sites. Surface instability risk may sometimes remain, especially where large underground voids exist. This paper illustrates the importance of failure mechanisms identification in order to define properly how to manage the residual risk. RESUME: La France fait aujourd’hui face à la fermeture de ses exploitations minières. Des risques d’instabilités de surface peuvent persister, notamment lorsque des vides résiduels existent au sein des travaux souterrains. L’article illustre l’importance que présente la nature des mécanismes de rupture potentiels dans le choix des mesures compensatoires à adopter pour gérer le risque résiduel à long terme. ZUSAMMENFASSUNG: In Frankreich stellt sich derzeit das Problem der definitiven Schliessung des meisten Bergwerke. In manchen fällen ist die Stabilität der Oberfläche nicht garantiert, speziell wenn unter Tage nicht verfüllte Hohlräume verblieben sind. Dieser Bericht zeigt die Wichtigkeit, bei der Auswahl geeigneter Langzeit-Risikomanagementmethoden, der verschiedenen Mechanismen mit denen ein eventueller Bruch an die Tagesoberfläche geraten kann.

Jan 1, 2003

By D. H. Diering

The paper deals with the technologies required for opening up anew idealized ultra-deep level mine. First the overall philosophy of accessing ore at ultra depths is discussed. Then the individual technologies which will be required are explored. Finally a detailed overview on one of the key technologies, namely tunnel support, is given. Because this project is still in its infancy, few definitive answers are provided; instead each of the envisaged technologies are briefly discussed, with emphasis on those which require the element of speed for rapidly accessing the ore body.

Jan 1, 1997

By M. A. van Nierop

The Discrete Element Method (DEM) is a model that is used to simulate the motion of the media in a grinding mill. The sum of the energy that is lost in inter-media and media-wall collisions represents the power drawn by the mill. The fact that the DEM predicts the power drawn by grinding mills over a large range of diameters has been used to show the validity of the DEM. However, the power drawn by a mill is a function only of the sum of forces of the load on the shell liners. A more accurate and detailed validation of the DEM would be to measure these forces as a function of angular position as the liner moves under the load, and to compare these measurements with predictions generated using the DEM. An experimental mill has been developed to reproduce exactly what the 2-dimensional DEM simulates. The 0,55 m diameter mill has a length of 0,023 m, which is fractionally larger than the diameter of the media used in the mill. One of the lifters in the mill has been instrumented so that the forces on the lifter can be measured as the mill rotates. The DEM simulation will be used to predict these forces. This will give experimental evidence of the validity of the DEM for modelling load behaviour in rotating grinding mills.

Jan 1, 1999

Plant survey data has shown that gold recovery through a specific copper concentrator was significantly lower than copper recovery. Size-by-size analysis revealed that this was due to poor recovery of+75 µm and ?23 µm gold containing particles. In order to further investigate the nature of the gold losses, experiments were conducted at laboratory scale. Gold deportment studies on the laboratory flotation products revealed that coarse gold (+75 µm) reporting to the rougher tailing was predominantly associated with non-sulphide gangue. Further grinding of the plant rougher tailing improved recovery of gold and copper, while not affecting iron recovery, due to improved liberation of gold from non-sulphide gangue in coarse size fractions. EDTA extraction to remove surface contaminants showed a similar improvement for fine, liberated gold flotation.

Jan 1, 2003

By D. Fukahori, K. Sugawara, A. Sato

X-ray Computed Tomography (CT) is a nondestructive imaging technique, and its efficiency is widely recognized. In the present paper, X-ray CT is successfully applied for the visualization of water permeation process in rock. A new experimental technique using a tracer, which mainly consists of Potassium Iodide (KI), is proposed, together with the analysis method of the velocity field. The permeation process and the velocity field in rock are concretely visualized and analyzed by considering the conservation of mass of the tracers. La tomographie calculée aux rayons X est une technique de la prise d'images non-destructive et son efficacité est largement reconnue. Dans le présent exposé, la tomographie calculée aux rayons X Radio est appliquée avec succès à la visualisation du procédé de perméation de l'eau dans la roche. Une nouvelle technique expérimentale, se servant d'un identificateur principalement constitué d'iodure de potassium (KI), est proposée avec la méthode de l'analyse du champ des vitesse. Le procédé de perméation et le champ des vitesse dans la roche sont visualisés concrètement et analysés en considérant la conservation de masse des identificateurs. Röntgen-Computer-Tomografie (CT) ist eine nicht-destruktive Bildverarbeitungstechnik, deren Effizienz weit anerkannt ist. In der vorliegenden Arbeit wird Röntgen-CT erfolgreich für die visuelle Darstellung des Wasser-Durchdringungsvorgangs im Fels eingesetzt. Eine neue experimentelle Technit mit einem Tracer, der hauptsächlich aus Kaliumiodid (KI) besteht, wird vorgeschlagen, zusammen mit der Analysemethode des Geschwindigkeitsfelds. Der Durchdringungsprozess und das Geschwindigkeitsfeld im Fels werden konkret visualisiert und analysiert, wobei die Bewahrung der Masse des Tracers berücksichtigt wird.

Jan 1, 2003

The modern theory of sampling of particulate minerals essentially consists of a recent generalization of the procedures for applying and calibrating the formula usually known as ?Gy?s Formula? for sampling variance control, in which the central concept is a parameter called the liberation factor l. A model which can be experimentally adjusted was proposed by one of the authors several years ago, based on geostatistical considerations. This new model, which relates the liberation factor to the sizes of the fragments and mineral grains, solves the usual difficulties faced in the past, and permits predictions that are well verified in practice. Unfortunately, an older, arbitrary and less general formula is still widely used. The vast majority of today?s misapplications of Sampling Theory of Particulate Materials can be traced back to the use of this antiquated and generally incorrect model. Following a brief history of the models used for the liberation factor and a description of its main variable, the liberation size, and to illustrate the importance of proper modelling of l, this paper presents demonstrative calculations of the absurdity of the incorrect model using the particular case of gold mineralization as an example, followed by some more positive examples of application.

Jan 1, 2002

By B. M. Nyombolo

Mintek has been involved in the development of bioleach technology for many years, initially for refractory gold extraction, and more recently also for base metals extraction. Mintek, in collaboration with its Australian technology partner (BacTech), is the technology provider for the Beaconsfield refractory gold bioleach plant. At present Mintek, BacTech and Peñoles are constructing a demonstration bioleach plant for copper-zinc concentrate treatment. Bioleach liquors produced in all applications have to be neutralized. In the copper-zinc case, neutralization is required for bleeding iron from the circuit and for adjusting the pH value ahead of solvent extraction. In the refractory gold bioleach circuit, neutralization is required for producing a stable iron-arsenic residue. Some of the challenges encountered in each of these neutralization applications are discussed, and examples of results obtained are presented.

Jan 1, 2000

By Q. G. Reynolds

DC arc furnaces are widely used for steel scrap melting, and are increasingly being used for smelting applications as well. The electrical resistivity of slags varies widely, from highly conductive slags in ilmenite smelting, to highly resistive slags in applications such as cobalt recovery from non-ferrous slags, and nickel laterite smelting. Models have been developed to predict the electrical behaviour of the DC open plasma arc and the molten slag bath. These models allow the voltage and current ranges of furnace power supplies to be specified.

Jan 1, 2004

By G. S. Littlejohn

Following study of historical South African practice and a review of recent experience gained during the design, construction and testing of the high pressure plugs at the South Deep Water Barrier Project, this paper makes recommendations to improve practice. Initially, site investigation requirements are described with reference to geological, hydrogeological and seismic considerations, including site preparation and pre-grouting of the surrounding rock mass, if permeable. Structural and hydraulic aspects of plug design address topics such as residual permeability, aggressive mine water, plug materials, mortar strength and bleed. In situ thermocouples and piezometers are recommended to optimize the timing of plug tightening and monitor plug performance during service. Plug construction covers aggregate preparation, mortar quality control, plug tightening grouts, injection pressures, records and the overriding need for a method statement specification to control all aspects of plug construction. On completion of the plug, tests to establish surrounding rock stress regime, plug strength, and residual permeability are described to enable a comparison with original design assumptions. Monitoring and maintenance procedures are proposed to ensure satisfactory long-term performance of the plugs.

Jan 1, 2006

By R. L. Gibson

Manpower competencies in the mining, minerals processing and energy industries in South Africa into the next century will, to a large extent, derive from the nature and quality of the teaching which pupils receive at school. This paper provides an overview of the current developments towards a new National Curriculum in South African Schools and highlights areas in which the Minerals Industry might provide input into this process.

Jan 1, 1997

By R. J. Durheim

Detailed investigations have been conducted into 21 rockbursts which caused damage to excavations in deep South African gold mines, in many instances resulting in the death or serious injury of workers. The objective of this study is to determine the principal factors controlling the severity and distribution of damage, so that strategies to reduce the hazard of rockbursts may be developed. It was found that the source mechanism is often controlled by the mine layout, and regional structures such as faults and dykes; while local rock conditions and support systems strongly influence the location and severity of damage. In the short term the most important lever for reducing the rockburst hazard is the effective implementation of existing rock engineering knowledge and technology.

Jan 1, 1998

Viscosity measurements were carried out on slags in the CaO-Cu2O-CuO-MgO-SiO2systemcontaining ~ 63 wt% SiO2in air. The experimental work was carried out over a range of temperatures where the slags were completely liquid. Initial measurements were on a binary CaO-SiO2slag to which incremental additions of CuxO-MgO-SiO2slag with the same silica mole fraction were made. The viscosity-temperature relationship was measured for slags with‘Cu2O’contents of 0.02, 0.19, 0.38, 0.79, 1.69, 2.47, 3.01, 5.31 and 10.0 wt%. The proportions of Cu+and Cu2+in the slags were determined. The oxidation state of Cushifted from predominantly Cu+to Cu2+, with the Cu+/Cu2+ratio of approximately 0.3 for slag with a Cu content above 2 wt%. This is equivalent to Cu1.13O. The trends observed for changes of Cu2+/Cu+redox ratio with slag chemistry were consistent with the literature. Decreasing the CaO content by substituting copper oxide resulted in a decrease in the Cu+/Cu2+redox ratio. The change in ratio corresponded to a shift of the value of x in CuxO from an initial value of 1.8 to 1.1,when the slags contained 10% ‘Cu2O’. In this study, the SiO2content of the slags varied between 64 and 60 wt% as the Cu content increased. The viscosity of the slag containing 10 wt% CuxO was nearly 4.5 times lower than the binary CaO-SiO2slag. As the silica mole fraction (xSiO2) actually stayed constant (0.61±0.009),the results show that CuxO acted as a network breaker. Comparison with other ternary slags with similar silica mole fractions suggest that that addition of CuxO to silicate slags has a stronger effect on lowering the viscosity than FeO or MnO has on a molar basis. Keywords: viscosity, copper, silicate, slags

Jan 1, 2004

The 103rd Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 16th August, 2000. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past Presidents, our Members and other guests, among them the following: Reinie Meyer, President, The Geological Society of South Africa Dr Nielen van der Merwe, Chairman, The South African Institute of Rock Engineering Chris Fourie, President, Institute of Mine Surveyors of South Africa

Jan 1, 2000

The corrosion behaviour of a low carbon steel was investigated in natural seawater and various synthetic seawaters. It was found that the steel corroded nearly four times faster in a 3.5% NaCl solution than in natural seawater for an exposure time of 21 days. The corrosion rate after immersion in synthetic seawaters (ASTM D1141 and Marine Biological Laboratory seawater) is similar to the corrosion rate after immersion in natural seawater. Calcium carbonate (aragonite) deposits were found on the surface of the steel after immersion in natural seawater and the synthetic seawaters. Some magnesium-containing deposits were also found after immersion in the natural seawater. These deposits act as a barrier against oxygen diffusion and thereby lower the corrosion rate. The morphology of the calcium carbonate deposits that formed during immersion in the natural seawater is different from those formed during immersion in the synthetic seawaters. This may explain the slightly lower corrosion rates obtained in the natural seawater. X-ray diffraction also showed that the oxy-hydroxides formed in the 3.5% NaCl solution differed from those formed in the other solutions. Keywords: Corrosion, seawater, low carbon steel, 3.5% NaCl, aragonite

Jan 1, 2006

By Chris M. Haberfield, Neil D. Benson

The assessment of overall modulus (or stiffness) of a fractured weak to moderately strong rock mass is a key parameter in the design of civil engineering works in these materials. It also provides the highest level of uncertainty due to scale effects, anisotropy and the influence of joint frequency and joint stiffness. Using the example of the Melbourne Mudstone, this paper compares approaches using empirical rules based on intact rock strength, laboratory testing, in situ field testing, semi-quantitative assessment techniques based on rock mass classification and back analyses. L'évaluation du module (ou rigidité) global d’une masse rocheuse faible et fissurée a modérément forte est un paramètre principal dans la conception des travaux du génie civil dans ces types de matériaux. Elle fournit également le niveau le plus élevé d'incertitude due aux effets d’échelle, à l'anisotropie et à l'influence de la fréquence et de la rigidité des joints rocheux. En utilisant l'exemple du schiste de Melbourne, cet article compare des approches empiriques basées sur la force intacte de La roche, les essais expérimentaux au laboratoire, les essais sur site, les techniques semi-quantitatives d'évaluation basées sur la classification de la masse rocheuse et les analyses en retour. Die Schaetzung des allgemeinen Steifigkeit-Moduls des gebrochenen schwachen bis zu maessig starken Felsmassen ist eine Haupt- Annahme in dem Entwurf von Tiefbau-Projekten in diesen Materialien. Es verursacht den hoechsten Grad der Ungewissheit in Folge der Groessenordnung, Spaltorientierung und dem Einfluss der Haeufigkeit der Risse und Bruch-Steife. Unter Verwendung des Beispiels des Melbourner Tonsteine, vergleicht diese Darlegung die Anwendung der empirischen Regeln, die sich auf die Staerke des ungestoerten Fels Basieren mit Versuchen in der Material Pruefungsanstalt, Untersuchungen auf der Baustelle und halb-quantitative Schaetzungsverfahren, die sich auf die Felsmassen Klassifikation und fruehere Analysen stuetzen.

Jan 1, 2003

By F. Peer

This Technical Note was presented as a poster at the Western Cape Mineral Processing Symposium held in August 2001 The cleaning of fine coal (-1000 µm) in today?s coal preparation plants is an economically important factor. Coals with high ash contents are, in general, commercially undesirable. Current well-known techniques for treating fine coal include froth flotation and spirals. The primary critical factor with regards to spirals is the efficiency of the process whereas that of flotation, is the cost of there agents used. Research into enhanced gravity separation techniques has resulted in several commercially available enhanced gravity separators. This project was based on a preliminary investigation into the feasibility of one such separator, to effectively treat fine (-500 µm) coal. Experimental variables included particle size and speed of rotation of the said instrument. The performance of the separator was compared to the results obtained from liquid density separations done for the two coal fractions evaluated. From the results obtained in this preliminary study it appears that the piece of equipment investigated does not measure up to expectations. Recommendations for further investigation include the evaluation of the instrument on other South African coals to obtain conclusive results.

Jan 1, 2002

By R. J. Davidson

Arguments are presented in favour of a new interpretation of the chemistry pertaining to the dissolution of gold, when this takes place in typical gold plant leach circuits where calcium is present in solution. It is suggested that under these conditions the standard chemistry, as it applies in the absence of calcium, is no longer valid. Thus the concept of very soluble sodium and aurocyanide ionic species in solution is replaced by the presence of weakly soluble calcium aurocyanide, which is a covalent coordination complex that is non-ionic. Supporting evidence for this is provided and the implications that the presence of calcium in gold plant circuits may have for operational efficiency are discussed. In particular, because of the formation of this weakly soluble calcium complex, the addition of lime to the leach circuit is questioned. Arguments for the use of a sodium hydroxide/sodium carbonate/sodium bicarbonate buffer solution as a means of controlling pH and of increasing ionic strength in a so-called ?soft? leach are presented. Such a lime-free system, besides benefiting the leaching of gold, would have many downstream benefits in existing CIP circuits. Furthermore, the direct electrowinning of gold from the leach now becomes potentially feasible.

Jan 1, 2007

A large number of brittleness concepts have been used in very different studies in the literature. One of them is the B1brittleness concept. In this study, the objective is to criticize the B1 brittleness concept on rotary blast hole drills. The B1 brittleness concept, the ratio of uniaxial compressive strength (sc) to tensile strength (sT), are widely used as a rock brittleness concept in the literature (Inyangand Pitt, 1990; Verhoef, P.N.W. 1993; Neil, D.M. et al.1994;Becker, et al.1984; Evans and Pomeroy, 1966; Göktan, R.M.1992; Kahraman, S. 2001; Yamaguchi, U. 1970; Verhoef, P.N.W. et al.1996; Bilgin, 1982; Howarth and Rowlands,1987; Howarth, D.F. et al. 1986). So, it was used as a rock brittleness concept in this article. The value of the B1brittleness concept is equal to the tangent of ß angle in the following graph. It was seen that more meaningful relationships could be obtained with the B2 brittleness, the under ?Area?(= 1/2(scxsT) = B2) under the curve, instead of tangent ß, (=B1), of the curve.

Jan 1, 2003

By F. T. Cawood

Monitoring of the slopes of surface mines can prevent loss of life, loss of equipment, loss of production and possibly the loss of the mine. The effectiveness of such monitoring depends on the extent to which slopes give adequate advanced warning before failing, and on the ability of the monitoring system to detect such warning. In this paper an overview is given of slope monitoring requirements, from both the geotechnical and survey points of view, as well as the types of equipment and instrumentation that are available. Legal issues relevant to slope monitoring are also dealt with. It is concluded that conventional geotechnical and survey instrumentation will continue to have their place in slope monitoring. However, the slope monitoring scene has changed substantially in recent years. A real and volume-based monitoring equipment is now available and this has provided, and will continue to provide, the means to improve safety, and to enhance productivity in mining. Its benefit to slope management is substantial. In the near future it is expected that data obtained from such equipment will add a much needed new dimension to slope engineering, and be used to improve slope designs and to optimize slope angles.

Jan 1, 2006

By L. Nell

Bateman, like other engineering contractors, carries out or participates in many studies of potential projects in the Minerals Industry. This paper aims to explain the contracting approach to feasibility studies as practiced by Bateman, particularly where this differs from a traditional mining company approach. A brief description is provided of the usual phases of a project and the types of estimate needed to proceed from one phase to the next. Possible organizational structures involving different forms of association between owner, contractor and consultants are then outlined. The bulk of the paper then demonstrates that the cost estimates prepared stem directly from the mining plan, metallurgical process design and engineering design philosophy. The steps to be followed in order to prepare a credible estimate which accurately reflects the design constraints are described. The importance and the methodology of carrying out value engineering and of preparing contingency estimates based on a thorough risk analysis exercise are then discussed. Financial modelling techniques are described briefly. The paper concludes with short summary case studies of two recent investigations of potential projects in Africa.

Jan 1, 1999