Search Documents

By C. F. Vos, J. D. Miller, J. C. Davidtz

Small replacements of C12-trithiocarbonate (C12-TTC) for dithiocarbonate (DTC)/dithiophosphate(DTP) in a reagent suite for the flotation of platinum group metals (PGM) have significantly improved the rejection of gangue. Coupled to this is an improvement in kinetics, grade and recovery of PGMs. In a pilot-plant trial, after a 5 mole per cent replacement of the current DTC/DTP collector combination by C12-TTC, large opaque bubbles were replaced by small clear ones. In addition, a similar flotation response was realized with one-third of the current depressant dosage. During a preliminary plant trial on underground UG2 ore, the initial rougher concentrates were characterized by higher PGM concentrate grades and this was in part due to improved chromite rejection. The concentrate produced from the TTC trial also exhibited a much finer particle size distribution. The overall circuit performance, which included secondary regrind and flotation, showed an increase in concentrate grade of approximately 44% while the tailings grade remained unchanged

Jan 1, 2006

By M. Sanchez, C. Morales, J. Palacios

The slag produced in the Peirce Smith converters at the Ilo smelter of Southern Peru Copper Corporation has shown a wide range of magnetite content, which introduces an additional problem in the smelting units due to materials? recirculation. However, the operation data analysis and the application of thermodynamic concepts have made it possible to produce slag with magnetite content between 18 and 20%. The results have suggested that matte grade enhances magnetite formation while silica controls its precipitation, and they are also influenced by the increasing temperature of the slag. Thus, in order to obtain the required magnetite content in the slag, matte grade is gradually enriched in equilibrium with slag containing from 25 to 32% silica.

Jan 1, 2004

By B. Friedrich

In a German governmental funded three-year research project, a closed loop recycling process for Nickel-Metalhydride-Batteries (NiMH) is under development. Today the discarded batteries are used in the steel industry as a cheap nickel source. Cobalt and rare earth (RE) are slagged and lost for reuse. The entire value of the metals in discarded Ni-MH is estimated to be 4?-4.5 ?/kg. Spent NiMH-batteries containing 36?42 per cent Ni, 3?4 per cent Co and 8?10 per cent rare rarth (Ce,La, Pr, Nd). The dismantled and processed NiMH-batteries are melted in a DC electric arc furnace producing a nickel-cobalt alloy and a slag phase highly enriched with RE-oxides. The key to success in this process is to find a suitable slag system, which ensures best separation of NiCo-alloy from the rare earth oxides and high concentration of RE in the slag. Different oxidic and halogenic slag systems are investigated in the melting process. So far a slag system based on 65per cent CaF2 and 35 per cent CaO delivers the best separation of the two phases and metal yields. A slag with a composition of 20?25 per cent La, 13-16 per cent Ce, 1.5?2.5 Pr, 4.5?6.5 per cent Nd is obtained and further treated to misch metal hydro-/electrometallurgically. The first results of the influence of rare earth oxides on the density of CaO-CaF2slag system are shown at 1600°C. Keywords: battery recycling, CaF2, CaO, rare earth oxides, slag characterization, density measurement

Jan 1, 2004

By E. T. Boshoff

Paper written on project work carried out in partial fulfilment of B. Eng. (Metallurgical Engineering) The weathering of kimberlite can be accelerated with cations in solution if swelling of the kimberlite occurs in contact with the weathering medium. The type and amount of swelling clays present, along with the surface charge and cation valence, determine the degree of swelling that can occur. Crystalline swelling occurs by the incorporation of cations in the interlayer spacing of the silica sheets. Kimberlite exposed to cupric cations showed very strong weathering, indicating that this type of weathering may be considered a viable process option. Kimberlite fines generated after weathering with monovalent cations showed poor settling behaviour compared to kimberlite weathered with di-, and trivalent cations.

Jan 1, 2005

By Simon St J Tose

The objective of this paper and presentation is to review the different criteria and methodology used by AEL and other organisations to create a pre-split design which delivers a stable highwall for the life of that part of the mining operation. It will look at the need to adapt and change the way, size and direction of the production blasts as the mining phase approaches the highwall position for which a pre-split has been created. Key Words: Pre-split: Design; Highwall; Perimeter

Jan 1, 2006

The distribution of chrome spinels in a magnetically fractionated ilmenite concentrate sourced from the Murray Basin was characterized by XRF assaying, quantitative electron microprobeanalysis, grain mapping, automated mineral phase clustering, and modal analysis. At least 14 distinct chrome spinel types were present in the concentrate. There is considerable variation in the amount of each chrome spinel type present, although a high-Mg, high-Al phase makes up close to 45 per cent of the total spinel population. Magnetic fractionation results showed significant variation in the composition and relative abundance of spinels reporting to each fraction. Low magnetic field strength fractions (ie. high susceptibility grains) were dominated by chrome spinels that are mid-range in Al and Cr. These spinels have the highest magnetite, ulvospinel and Fe(Al,Cr)2O4components. In comparison, the high field strength fractions (i.e. low susceptibility grains) have the majority of the grains with high-Al contents indicating a higher proportion of Mg(Al,Cr)2O4component. Spinels high in a (Al,Cr)2.67O4non-stoichiometriccomponent are absent at low field strengths but tend to be concentrated in the high field strength, non-magnetic fractions. Intermediate field strength fractions tend to exhibit a broad spread in spinel compositional types. A mild roast treatment of the sample had no clear effect on the distribution of chrome spinels between different magnetic fractions, but it did cause a change in the magnetic properties of the accompanying ilmenite grains. The effect of more extreme roasting conditions on the magnetic properties of the chrome spinels is to be determined.

Jan 1, 2003

By H. Möhle

Premier Mine is a large underground diamond mine, situated at Cullinan in the Gauteng Province of South Africa. The mine hoists over 3 millions tons of diamond bearing kimberlite per year, from a modern, mechanized panel retreat block cave mining operation. Troughs sited at the base of the cave are developed into the overlying caved ore, allowing loading access to the ore through draw points. Trough opening is therefore a vital aspect of the mining operation. Most of the production is dependent on fast, reliable and safe trough opening. Successful trough openings are achieved under difficult mining conditions due to restricted void, long up-holes and the inherent properties of kimberlite?soft, elastic rock with a high swell factor. Early in 1998, Premier Mine undertook a joint development project (with an electronic initiation system supplier) to determine whether the use of a fully programmable electronic detonator system would enhance the mining cycle in the trough opening process. Blasting commenced in February 1998, initially with blasts of a similar size and duration to those that had been previously blasted with shock-tube systems, to confirm the operational capabilities of the blasting system. The accuracy, reliability and flexibility of the electronic delay detonators (EDDs) minimized associated risks for re-engineering of the trough opening process. Further, as blast timing was optimized, larger blasts were successfully initiated. To date over 20 troughs have been opened successfully with the use of EDDs. Not only did it take less time to open troughs, but also drilling and blasting operations have been optimized, as well as an overall improvement in safety. This paper details the benefits that EDDs have delivered to Premier Mine in this area. The logic followed is: ?Review of the original trough opening practices ?Re-engineering of the trough opening process ?Implementation of EDDs ?Evaluation of improvements and conclusions.

Jan 1, 2000

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The stability of a ferrosilicon dense medium suspension is one of the most important parameters to keep under control since it determines the density gradient of the medium in the separation zone and thus directly influences separation sharpness. The stability of ferrosilicon suspensions were characterized using settling tests employing a differential pressure method. Particles smaller than 45 µm and especially the ore fines played an important role in the settling behaviour of the solids. High medium stability is favoured by ore fines, fine medium particles, and high medium densities. Keywords: dense media, ferrosilicon, dense medium stability, ore fines

Jan 1, 2002

By J. Lehmann, H. Gaye

A brief review of Computational Thermodynamics software concerning the modeling and prediction of reactions involving metals, slags and fluxes is presented. Their application for various steelmaking treatments is discussed. Examples concern phosphorus removal in BOF and EAF, ladle steel desulfurization, and specific treatments for inclusions control in semi-killed or Al-killed carbon and stainless steels.

By P. J. D. Lloyd

The widely employed IPCC models for the release of methane from underground coalmining operations are reviewed, and put in the context of the South African National Communication on greenhouse gas emissions. Then attempts to calibrate the model via measurements on South African coalmines are described. These attempts failed because it rapidly became clear that the IPCC model, involving methane adsorbed by the coal and released (a) by the depressurization of the strata caused by mining, (b) from the broken coal and (c) from coal remaining in roof, floor, pillars or goaf after mining, was not valid. Instead, measurements showed that the methane release was very variable, sporadically falling to zero. Carbon dioxide concentrations were monitored at the same time as methane, and followed methane concentrations. An alternative model was developed, in which methane was largely displaced from the coal and held in fissures, cleats and pores, which, when intersected by mining, released methane into the ventilation stream. In a key test of this hypothesis, methane concentrations around a continuous miner were monitored both during operation and after shutdown. Even during operation, methane became undetectable. It is hypothesized that heating of the South African coal-seams during the emplacement of the igneous dykes that cut so many of the seams caused displacement of the methane from the coal into the pores. This fissure-held methane, or free methane, is released rapidly once a pathway through the coal into the mine atmosphere is established. In contrast, methane adsorbed in the coal, and measured as the seam gas, desorbs relatively slowly. Measurements suggest that on average about 50%of the adsorbed methane is lost one day after mining. By that time, the coal will have left the mine, so that the remaining seam gas will be released to the atmosphere outside the mine. Attempts to measure methane emissions from surface coal-mining operations showed very little detectable methane. Coal from surface operations, which was milled and exposed to atmosphere, adsorbed gas from the air. It is concluded that methane release from surface operations is probably less than 3Gg/a. It is estimated that the total methane release from the coalmining industry amounts to about 72 Gg/a, as opposed to the National Communication estimates of 323 Gg/a in 1990 and 317 Gg/a in 1994. However, there are large errors associated with these estimates, and it is recommended that the methodology outlined in this report be extended to as many mines as possible to reduce the errors that are inherent in the physical processes underlying the release of methane from South African coalmines.

Jan 1, 2005

By M. Rakoma

Following the blasting fatality on 17 December 2009, Landau Colliery was forced to change from the blasting practices that had been utilized since the start-up of the mine. Since then, attempts have been made to optimize blasting results. The challenge is rooted to the mining environment - during the early life of the mine, mining took place in virgin areas, whereas currently mining is taking place in areas overlying old underground bord and pillar workings. The underground bord and pillar workings aggravate phenomena such as spontaneous combustion, hot holes, and sinkholes. The 2009 fatality was attributed to hot holes causing premature detonation. Landau has been struggling with poor results from their overburden and coal blasts; leading to poor fragmentation of overburden and the PI parting that lies between the No.1 and No.2 coal seams. An extensive literature survey was completed in order to identify possible alternative solutions that could be evaluated for this unique mining environment, which demands a high degree of caution during mining to ensure factors such as dragline stability and personnel safety. The literature survey confirmed that the previous blasting technique, which was mainly characterized by air decking, was indeed the more efficient, although it was deemed unsafe because of the possibility of hot holes and the high sensitivity of detonators. Potential modifications to the blasting technique were modelled in a Microsoft Excel simulation that was available from the mine, and pit visits were conducted in order to determine whether implementation would be a problem. From the model it is evident that results can be improved by changing the current burden and spacing ratio. Visiting the pit revealed that the tie-in pattern and drilling inaccuracies are contributing to problem areas.

Jan 1, 2013

By M. Tangstad, D. Lu, G. Tranell, S. Gaal, J. Safarian

The kinetics of MnO reduction from high carbon ferromanganese slag was investigated using a sessile drop technique at 1600 ºC. The effects of reductant type, ambient atmosphere and slag composition on the MnO reduction were illuminated. Two different types of industrial reductants (ground to a particle size of 44 to 106micron and pressed to pellets) were used as substrates for small slag droplets of varying composition, which were reacted in a CO or Ar atmosphere with the reaction studied in-situ. The cross sections of the reacted slag-carbon samples were subsequently studied by EPMA to find the extent of MnO reduction as a function of reaction time. It was found that the rate of MnO reduction is affected by both the type of reductant, the ambient atmosphere and the presence of metallic components in the slag. Higher reduction rates were obtained for charcoal than for coke as reductant while a CO atmosphere unexpectedly yielded faster MnO reduction than an Ar atmosphere. It was also found that metal prills in the initial slag will increase the rate ofMnO reduction.

Jan 1, 2007

By W. Stumpf

Mill log analyses and complementary hot deformation studies were carried out on the as-cast structure and on a hot rolled structure of the same low carbon steel (SAE 1006) that had been processed according to the direct or hot charge route in a compact strip plant. The main softening mechanisms during hot rolling were found to be complete dynamic recrystallization during each pass above about 1000°C for the as-cast structure with an austenite grain size of 277µm and, secondly, incomplete static recrystallization after each pass with a finer austenite grain size of about 26 µm and tested below 1000°C. A two-stage hot working mechanism has also been found by others on a similar steel also processed by the hot charge route and this may appear to be a characteristic of this type of material. Constitutive constants determined from hot working studies were combined with other constants from the literature and incorporated into a grain size development model that correctly predicts the final ferrite grain size in the hot rolled strip steel. The predicted incomplete static recrystallization during the last three finishing passes in the plant appears to result in some retained strain in the hot rolled austenite as it transforms to ferrite on the run-out table. Analyses with the model predict relatively little sensitivity of the final ferrite grain size to process and product variables such as temperature and strain per pass for the last three passes and also the starting austenite grain size in the slab. Keywords: Low carbon steel, hot rolling of strip steel, rolling mill log analyses, austenite grain size, ferrite grain size, grain size modelling.

Jan 1, 2003

By David Norval

The increased tendency to use hydrometallurgy as an extraction step towards final refining following a pyrometallurgical smelting process requires melts which have to be cast and or comminuted which can then be taken up into solution or leached. To generate surface area for optimal leaching, a common process is to granulate and in many cases mill, which is a general practice with friable material with properties associated with higher sulphur, carbon and silicon levels. However, in the case of metallic melts milling can be unfeasible due to the ductility of the granulated particles. Water solidification is capable of producing either fine particles by means of granulation or atomisation. Atomisation however, can produce particles as fine as 40 microns without a milling circuit.

Jan 1, 2005

By R. Dass

Paper written on project work carried out in partial fulfilment of B. Sc Eng (Extractive Metallurgy) degree Screening is an industrial process that splits material at a specific cut size into one fraction of particles larger than the cut size and another fraction of particles smaller than the cut size. Particles are vibrated to increase the probability of them being accurately classified and to move the oversize particles off the screen surface. In conventional screening, the screen mesh vibrates with a single frequency and the particles on the screen are all exposed to this same frequency. The Ultimate Screener (see Figure 1) is a new screen technology that imparts multi-frequency vibrations to the screen mesh so that different parts of the screen surface vibrate at different frequencies. The Ultimate Screener incorporates an additional deck that holds the multi frequency adapters as shown by Figure 2. These special adapters can transform single frequency vibrations into multi frequency vibrations. When the screen motors are switched on they begin to vibrate. This vibration is transmitted to the adapters via the body of the machine. The adapters then modify the vibration to have multiple frequencies, which are transmitted to the screen surface via resonating rings.

Jan 1, 2004

By T. Tamura

It is known that the CaO-FetO-P2O5slag system has a wide liquid miscibility gap at steelmaking temperatures and this two-liquid slag phase has many advantages such as high activities of both FetO and CaO and high amount of P2O5. The phosphorus distribution ratio between the two-liquid slag and molten steel was confirmed to be higher than that between CaOsat.-FetO-P2O5slag and molten steel. The two-liquid slag may be useful for dephosphorization of molten steel and reduction of slag volume. Furthermore, the phase equilibrium of two-liquid CaO-FetO-P2O5slagsaturated with MgO was measured to determine the applicability of the two-liquid slag to dephosphorization in steelmaking process. Keywords: slag, refractories, solid solution, two-liquid phase, dephosphorization, steelmaking, phase equilibrium.

Jan 1, 2004

By J. M. Font, R. G. Reddy

Jan 1, 2004

One of the most important factors leading to the success of a cement plant is its location. A multicriteria decision-making method is used to rank alternative plant locations. The set of criteria is established and corresponding criteria should be established for each case study, although this multicriteria decision-making approach has broader applicability. In this paper, the analytic hierarchy process (AHP) with 5 criteria is used to develop a location evaluation hierarchy for an alumina?cement plant in East Azerbaijan province of Iran. Five alternatives for the plant location are evaluated. The main criteria are transportation, water supply, power supply, fuel supply and land. Other criteria have the same importance as these five alternatives. The alternatives are ranked by a multicriteria method and the best site is proposed. Keywords: plant location; multicriteria decision-making

Jan 1, 2005

By R. Zivojinovic, S. Vujic, T. Tanaskovic

The problem of determining the optimum exploitation life of machinery, namely the optimum time for machinery and equipment replacement, represents a complex and highly responsible engineering task. Taking into consideration the situation prevailing at coal pit mines in Yugoslavia, the tasks of this class are very complex and difficult. To make a decision on replacement of capital equipment and machinery, such as bucket wheel excavators within the mentioned systems, understands a management task of utmost responsibility. It requires high professional and analytical knowledge as well as the reliable arguments, based on multidisciplinary professional approach. In this paper, the authors present their views on the problem of establishing the optimum exploitation life of bucket wheel excavators, offering an algorithm, based on dynamic programming, as a solution. Keywords: Bucket wheel excavators, exploitation life of machinery, optimization, operations research, theory of replacement, dynamic programming

Jan 1, 2003

By Alan Bye, Megan Little

Geology, and the detailed understanding of its properties, are fundamental to the optimal design and successful operation of any mine. To that end extensive fieldwork has been conducted at Anglo Platinum?s PPRust operation to collect geotechnical information both from exploration boreholes and in-pit mining faces. Since 1998, geotechnical data has been collected from over 337 km of exploration core, 7 km of exposed mining faces and more than 15 600 field and laboratory tests, in order to define the complete set of geotechnical properties for each rock type in the mining area. The geotechnical information collected is stored in two databases, SABLE Warehouse and MineMapper3D before it is imported into the Datamine mining software package. The geotechnical parameters, mining rock mass rating system (MRMR), uniaxial compressive strength (UCS), fracture frequency per metre (FF) and rock quality designation (RQD), are modelled using geostatistics to generate a 3D geotechnical block model. Data is interpolated between exploration boreholes and exposed mining faces and modelling is constrained, using wireframes, by rock type and structural features. By having detailed geotechnical information available in a 3D model that can be readily accessed and interpreted, significant production optimisations, feasibility studies and planning initiatives can be implemented. From a slope design perspective the model is used to target data deficient zones and highlight potentially weak rock mass areas. As this can be viewed in 3D, the open pit slopes can then be designed to accommodate the poor quality area before it is excavated. It also follows that geotechnical zones can be readily identified and the slopes optimised accordingly. Rather than viewing the drill and blast department as an isolated cost centre and focussing on minimising drill and blast costs, the fragmentation requirements of the comminution and load and haul business areas are studied. It is well understood that chemical energy is the cheapest form of comminution and that major downstream benefits can be derived by increasing drill and blast expenditure. 238 blasts were assessed to determine the optimum fragmentation requirements for ore and waste. Based on the study a mean fragmentation target of 150 mm was set for delivery to the crushing circuit and a mean fragmentation of 230 mm was set for waste loading from the pit. Substantial benefits have been realised in the drill and blast department by developing empirical correlations that relate the MRMR values in the geotechnical model to a blastability index, fragmentation, required powder factor and costs. As the geotechnical model can predict changes in geotechnical conditions, the blasting

Jan 1, 2007