Search Documents

By D. van Heerden

In the mining industry abrasion caused by both sliding and impact have over the years resulted in costly damage to installations such as ore passes and silos. Good geotechnical practices combined with the use of a high quality abrasion resistant concrete can prolong the life of such an installation and minimize problems associated with abrasion. In order to maximize the life of an abrasion resistant concrete, the choice and combination of the correct raw materials (cement, aggregate and fibre) and overall mix design needed to make up such a concrete are important. This paper presents technical data and practical experience showing that concrete formulated with calcium aluminate cement resists severe abrasion conditions better than similar OPC-based concretes.

Jan 1, 2005

By J. Böhlke, B. Friedrich, E. Hecker

The legislation for the disposal of heavy metals contaminated substances is still going to be tightened up in the future. The main criteria for the utilization or deposition of these residues are the content and the water solubility of these metals. Through this, the use of slags from the lead-and zinc-industry in road building may become limited or even not possible at all. From an economic point of view this would lead to Pb/Zn losses and costs for safe dumping. This paper investigates the feeding of the reducing agent via hollow electrode DC smelting and the yield of metal reduction. After carrying out thermodynamic calculations, the process window conditions for electric-arc furnace tests were determined. Doing this, the zinc could be reduced, evaporated and recovered as an oxidic intermediate product flue dust, while the lead was present either in flue dust or in metallic form. The zinc content in the final slag could be reduced by up to 90%. The slag product has undergone an eluation test which allows it to be used as building materials. Keywords: zinc reduction, lead reduction, hollow electrode, slag treatment, electric arc furnace

At the exploration stage for new mining projects or for medium- and long-term areas of existing mines (typical of South African gold mines), drilling data is on a relatively large grid. This grid is normally larger than the selective mining units (SMUs). Direct estimates for the SMUs and also of much larger block units will then be smoothed due to the information effect and the high error variance. Any capital-intensive project decisions made on the basis of any of the smoothed estimates will tend to misrepresent the economic value of the project or operation, i.e. the average grade of blocks above cut-off will be underestimated and the tonnage overestimated for cut-off grades below the mean grade of the orebody. This paper presents a direct approach technique for deriving recoverable resources, referred to as localized direct conditioning (LDC), designed to correct smoothing effects and also to provide support corrections.

Jan 1, 2014

By L. K. Witika, J. H. Masinja

"Investigations of flotation characteristics of Lumwana and Kansanshi ores using formulated frothers were carried out. Of the six frothers tested, two came from the alcohol family, two from the glycol family and last two were formulated products. The initial work involved determining the optimum mesh of grind and frother dosage for Lumwana and Kansanshi ores. Further work involved carrying out surface tension, bubble size and froth stability measurements. Finally, water recovery tests were conducted at Lumwana and Kansanshi mine sites. For froth stability tests, six frothers were tested on a two-phase (water–air) system using the Bikerman column flotation cell, while water recovery tests were conducted using a total of seven frothers, including the standards for each plant. The results of the testwork showed that (i) although a stable froth is essential for optimum recovery of valuable minerals, a higher molecular weight frother, like Dowfroth 250, caused poor selectivity when used on fine ores and (ii) a lower molecular weight frother was suited for Lumwana ore, while a mid to higher molecular weight formulated product was suitable for Kansanshi sulphide ore. INTRODUCTION Investigations of flotation characteristics of Lumwana and Kansanshi ores using formulated frothers were carried out. The initial work of this project involved determining the optimum mesh of grind and frother dosage for Lumwana and Kansanshi ores. Further work involved carrying out surface tension, bubble size and froth stability measurements. Finally, water recovery tests were conducted at Lumwana and Kansanshi mine sites. In order to investigate the gangue entrainment levels in the Lumwana and Kansanshi sulphide ores, two well-known methods (froth stability and water recovery) were used. Firstly, froth stability tests were conducted using six frothers, two from the glycol family (Dowfroth 200 and Dowfroth 250), two from alcohol family (MIBC and pine oil) and other two from the formulated family (Betafroth 20 and Betafroth 245), at the University of Cape Town’s Centre for Mineral Research (CMR) laboratories. Froth formation and stability measurements were conducted using the Bikerman column flotation cell."

Jan 1, 2015

This is a sampling of the papers presented at the conference, the proceedings can be bought from the SAIMM The technique reported here involves measuring the air pressures generated within sealed boreholes located behind blasts. Results from twelve free face blasts in competent rock environments a represented. There were no instances of high pressure gas penetration, even at distances corresponding to less than one blast burden. Rapidly generated underpressures were measured in most holes, with the magnitudes of the peak pressures decreasing with distance behind the blasts. It has been proposed that the under pressures are the result of new volume created due to crack formation and overall rock mass dilation. The experimental evidence is consistent with this, including a correspondence of the onset times of the peak underpressures with the nominal firing times of the nearest blastholes. New post-blast cracks were observed when using borehole video cameras in the monitoring holes. A calculation of new volume produced within the monitoring holes is proposed as an indicator of damage. While the data exhibit considerable scatter, there is a power function dependence on scaled distance, which resembles that of typical vibration data. The data also lie within the normally quoted vibration regimes for rock damage and are consistent with measured extents of damage. It is concluded that this technique may provide an inexpensive and practical comparative measure of near-field rock damage due to blasting. It is further concluded that gas penetration is not a common phenomenon. Damage appears to be mainly attributable to the nearest blastholes and the control of charge mass in perimeter blastholes is emphasized for damage minimization.

Jan 1, 2000

By F. T. Wang, Y. Yuan, S. H. Tu, X. G. Zhang

Hydraulic support instability (HSI) is one of the most common causes of disasters in underground coal mining, posing a threat to the safety of mine workers and normal operation of the equipment. It is prone to occur in fully-mechanized mining faces with a large mining height (FMMLMH), especially when the dip angle of the coal seam is large. The key to controlling HSI is to deduce its mechanism and employ effective control techniques. This paper focuses on the analysis of HSI types, the key parameters and techniques to control HSI in FMMLMH, the establishment of a model of HSI in FMMLMH, and a multi-parameter sensitivity mechanical model of different HSI forms in the no. 7219 longwall face in Xutuan Coal Mine, Huaibei Mining Group, by using sensitivity analysis . The results show that HSI mainly presents in three forms: hydraulic support gliding (HSG), hydraulic support tilting (HST), and hydraulic support tail twisting (HSTT). The occurrence of the above three forms depends mainly on support anti-instability capability. In the no. 7219 longwall face, HSG and HST are the main two forms of HSI. The dip angle of the working face and the friction coefficient between floor and hydraulic support are the sensitive parameters for HSG, while HST is strongly dependent on the dip angle of the working face and the friction coefficient between roof and hydraulic support. By the applications of measures such as the oblique layout of the working face, cutting the floor into a step pattern, moving the support under pressure, and raising the setting load, the support stability was controlled effectively.

Jan 1, 2015

By C. Kruger

Anglo American Platinum has adopted a strategy of best practice principles (BPP) for sampling, mass measurement, analysis, and metal accounting for more than a decade now. When new plants are designed, the most suitable sampling equipment and sampling protocols are implemented and material flows and plant layouts are designed around sampling strategies. A few years ago, a crushing plant for a high-grade matte stream was commissioned. The design called for the high-grade material to be crushed to 95% passing 2 mm, and the design allowed for a single-cutter primary Vezin sampler taking increments from a gravity flowing stream at regular intervals while filling a tanker for pneumatic offload at the base metal refinery. This was a single point of sampling and analysis that would measure the wanted output from the smelting complex and the input to the refineries. In addition, the design incorporated the functionality to collect increments in an ?interleaved? fashion from the Vezin sampler for internal precision checks. The metal accounting strategy for Anglo Platinum involves the ongoing measurement of all inputs, outputs, and stock levels for all operations for platinum group metal (PGM) and base metal (BM) content. Included are yearly stocktakes, usually done on 1 February, across the smelters and refineries (at least the base metal refinery). In the accounting period immediately following the introduction of the new crushing and sampling facility, a trend was developing whereby the absolute difference between the physical stock and theoretical stock (PGMs predominantly) increased for the two respective sites on an ongoing basis. The smelter showed an increase in physical stock compared to the theoretical stock (sender) and the base metal refinery showed an increase in theoretical stock against physical stock. Because of this anomaly, an additional stocktake was held in September for the period in question, and it was confirmed through the physical stock measurement results that the PGM accounting problem was indeed pointing towards the evaluation of the high-grade matte stream. This paper showcases parts of the process that took place to explain the poor accountabilities for the two sites. Previous results from the sampler ratification process (of the interleaved sampling design) were reanalysed, a physical inspection was carried out on the sampling system again, and the sampler performance was monitored (quality control parameters) for the period. From these investigations, it was found that airflows inside the Vezin introduced the sampling bias. A change in sampling protocol was introduced, as well as certain physical changes to the sampling equipment, to eliminate the airflow and thus the bias conditions significantly. The accounting period that followed the phased upgrading process showed that the accounting between the smelter and base metal refinery had been restored to within statistical limits (difference between physical and theoretical stock below 5% relative to theoretical stock). Keywords sampling, metal accounting, Vezin sampler, sampler bias.

Jan 1, 2014

By M. Ksiazek

Keywords: Thermal conductivity, thermal diffusivity, flash method, specific heat capacity, manganese ore Manganese ferro-alloys manufacturing involves a combination of quality raw materials and an energy source to produce high-quality products with low energy consumption. The thermal properties of manganese raw materials such as ores, sinters, and briquettes, are among the many factors that determine the amount of energy needed for processing. Thermal expansion, thermal diffusivity, conductivity, and apparent specific heat capacity of solid samples and compacted powder samples of manganese ores were examined from room temperature to 1000 °C. The effect of porosity (of the materials used) on the thermal properties was also investigated. The laser flash method and a pushrod dilatometer were used.

Jan 1, 2011

By I. Mc Dougall

Finite element models were generated of two submerged arc furnaces of different geometries. A 48MW circular furnace and a 68MW 6-in-line rectangular furnace were studied. The electrodes, raw material, slag and molten metal were included in the model. ANSYS/Multiphysics was used to predict the current density distribution in the electrodes, raw material, slag and molten metal as a result of the three phase AC current. The effect of the electrode immersion on the current path was studied. The ?proximity effect? caused a pronounced asymmetry in the electrode currents in the circular furnace, whilst the electrode currents in the rectangular furnace exhibited radial symmetry. The current distribution in the melt in both furnaces indicated that the bulk of the current flows between phases. The current density is greatest between electrodes. Results were compared to qualitatively similar published work, operating experience and results of furnace dig-outs.

Jan 1, 2007

By J. T. Nel

Non-transfer-arc linear plasma systems are highly suited to manufacturing nanoparticles. In this paper, the manufacturing of such particles with specially designed plasma systems is discussed. In general, it entails the volatilization of a metal halide that is injected in the high-temperature region of a plasma flame, where it is reacted with a suitable reagent, for example O2, to produce nanooxide powders. Metal powders can also be introduced directly in the plasma. Due to the very short residence time of only milliseconds in the reaction zone, as well as the fact that the reaction takes place in the gas phase, combined with very rapid quenching in the order of 10 000°C.s-1, nanoparticles are produced. At Necsa the manufacturing of such particles has been demonstrated on various scales. A pilot plant for the production of nano-Al2O3, and two pilot plants, one using SiCl4 and the other one using SiF4 as feed material, were built to produce fumed, pyrogenic, nano-SiO2. The alumina plant had a production rate of 8?10 kg.h-1 and the silica plants had production rates of 2 and 10 kg.h-1 respectively. Perfectly spherical alumina particles with a particle size distribution of between 10 and 200 nm were produced on a continuous system. Particle size analysis for the silica by SEM measurements showed a d50 of 60 nm and a particle size distribution of 30?100 nm. The specific surface area was in the range of 170m2.g-1. Other samples of plasma produced nanoparticles such ZnO and B4C will also be presented.

Jan 1, 2010

By X. Goso

Laboratory-scale tests were conducted at Mintek for the production of titanium powder from particulate Kroll sponge by the hydrogenation-dehydrogenation (HDH) process. The aim of this work was to produce titanium powder for powder metallurgical consolidations. The work involved the production of titanium powder at optimized conditions, which included hydrogenation in a horizontal tube furnace at 600°C for 2 hours, milling using planetary and roller mills, and dehydrogenation in a vacuumed retort fitted in a muffle furnace running at 700°C for 36 hours. The titanium powder produced in this project matched the elemental specifications of commercially available titanium powder, except for high carbon content. Nevertheless, the powder has been tested further in mechanical alloying and has been found suitable for the production of powder metallurgical compacts. Keywords Powder metallurgy, titanium components, HDH process, ball milling.

Jan 1, 2011

By S. L. George

The semi-solid metal casting process results in a unique solidification path. The microstructural features that were identified during the characterization of the as-cast microstructure, were used as evidence of the process history in order to determine the solidification path followed during the evolution of the microstructure. The morphology of the grains was characterized using SEM and the extent and distribution of the elemental segregation within the grain structure was analysed using EDS. Keywords Semi-solid casting, solidification path, segregation.

Jan 1, 2011

By C. Maree

Paper written on project work carried out in partial fulfilment of B. Eng (Chem. Eng.) This paper describes the development and use of a process simulator to optimize gypsum recovery at Afmine, a small plant near Yzerfontein on the South African West Coast. The simulator consisted of models of the major plant equipment, viz. hydrocyclones, surge bins, settling tanks, a primary sieve and a dewatering screen. Experimental data suggested that the equipment could be modelled satisfactorily from data published in the open literature. Simulation studies have indicated that gypsum losses on the plant could be reduced substantially by means of some relatively minor modifications to the plant layout. Moreover, sensitivity analyses of the plant have indicated that optimization of the settling tanks should receive priority over the other process units.

Jan 1, 2005

By T. van Heerden

A range of supported gold catalysts was prepared by ion exchange, varying many of the preparation variables, including concentration in the precursor solution, washing procedure, as well as drying and calcination procedures. These catalysts have been characterized extensively. TEM images show essentially the same crystallite size distributions, between 2?5 nm, for almost all catalysts, the only exception being catalysts not washed in ammonia, which did not show any small crystallites. Additional characterization with SEM yielded an interesting discovery. Catalysts that appear identical on the TEM also contain some large crystallites in the range of 50?500 nm. Differences in dispersion due to the drying procedure not seen on the TEM can now be observed. Oxygen chemisorption is being investigated as an additional method to characterize gold based catalysts to complement the typically used electron microscope techniques.

Jan 1, 2012

By E. Robles

The Tati Activox® Project (TA®P) is the first step towards the implementation of the Norilsk Nickel Activox® process. The ultrafine grinding (UFG) and autoclave pressure leach process conditions are the heart of the Activox® patent. Low grade base metal sulphide concentrates are leached in the process to recover the base metals and to produce LME grade nickel and copper cathodes and cobalt carbonates. The downstream processing of the metal-containing liquor produced by this process includes solvent extraction circuits to extract and concentrate metal-rich solutions, before the various final products are obtained. This paper gives an overview of many of the relevant design aspects taken into consideration in the design of the Tati Activox® solvent extraction circuits. It addresses key design elements related to leach process conditions such as scaling, materials selection for corrosive solutions, pH control, crud formation and treatment, multiple SX trains designed to prevent organic cross-contamination, and design aspects related to the mitigation of fire risks.

Jan 1, 2009

By I. J. Barker

Keywords: Submerged-arc furnace, plasma furnace, d.c. furnace, scale up, Søderberg electrodes, smart grid, demand side management, load shedding This paper argues that the scale up of furnaces and the supply of electricity are going to be two major issues that will affect the ferro-alloy industry in the near future, and that economic factors will drive this development. The most common type of furnace for producing ferro-alloys at present is the submerged-arc furnace with three electrodes, fed from a three-phase a.c. electrical supply. The scale up of this technology has now reached a fundamental constraint, which is caused by the electrical reactance of the secondary circuit. If the economy of any further scale up is to be achieved in the future then a different technology will have to be used. The supply of electrical power in future is likely to become a more complex issue than it is at present. Existing submerged-arc furnaces tend to run at fairly steady loads, but the ability to swing the load under demand-side management may offer advantages, and may allow a furnace to get cheaper power from the organisations that supply this power. This will have to be counterbalanced against the nuisance factors incurred by having a varying load in the operation of the furnace. Various options are therefore discussed in this paper. The possibility of scale up of Søderberg electrodes is discussed, as well as the use of d.c. power and multiple electrodes. Some of the issues with load swinging are also examined. A particular scenario is also briefly presented to show that considerable further scale up of ferro-alloy furnaces is still possible.

Jan 1, 2011

By G. van Aswegen

The geometry and morphology of a set of low-angle fractures around a stope in a deep Witwatersrand gold mine are explained in terms of extension fractures forming under variable conditions of stress. Primary extension fractures (E1) form some distance ahead of an advancing stope along the s1, s2 plane. With stope advance, a couple of these fractures end up in a stress regime conducive to transpressional shear and a secondary set of extension fractures(E2) is formed at a high angle to the primary fractures. i.e. at a low angle to the stope. As the E2 fractures are undermined, they migrate into a stress regime of transtensional shear and a third set of extension fractures (E3) may develop between E2 fractures. These have sigmoidal shapes, being parallel to the E2 fractures at the E2 discontinuity where s3 is negative, and curved through the un-fractured rock between E2 fractures where s3 is positive at the instant of fracturing. The fractures all display fractographic features characteristic of dynamic extension failure with striae indicative of the direction of rupture propagation and the local, instantaneous orientation of s1.

Jan 1, 2012

By B. Erdem

This article introduces a computer model, which emphasizes panel design for draglines deployed in direct side-casting mode. The study covers flat and inclined coal-seam conditions with the dragline operating along the strike-line. Two casting methods are embedded in the model: material is placed in the open set adjacent to the one on which the dragline is located (the DNS method) and material is placed in the open set adjacent to the one the dragline excavates (the DND method). While in the first method the unproductive walking time is reduced as the set is enlarged, in the second method the cycle time is lessened as the dragline swings along an acute angle. The side-casting model is shaped so as to provide several panel configurations instead of a single one to conform to the characteristics for an opencast mine. This is achieved by assigning the pit width an interval of values ranging from a minimum to a maximum. The model includes solutions to other critical design parameters such as: set length, swing angles at key cut and main cut positions, and required dragline reach at key cut and main cut positions. The model outcomes reveal the following: the stripping operation is largely affected when the coal-seam is inclined. The downhill spoiling mode should be applied wherever possible. The DNS pattern allows wider pit width intervals as well as longer sets and longer reaches.

Jan 1, 2004

By S. P. Pearton

"Pumpable emulsion explosives have been available to surface and underground massive mining operations for decades, and their unique properties offer significant advantages in terms of improved safety, reliability, and performance. However, the benefits of pumpable emulsions have been unavailable to narrow-reef mining operations due to the lack of technology necessary for their successful implementation in this challenging environment. Despite efforts to promote and enhance the safety and performance of bulk emulsions for narrow-reef stoping, little research has been undertaken to advance the pump technologies required for their implementation. This has resulted in a gap in knowledge and technology, and as a consequence the successful implementation of a pumpable emulsion system has consistently eluded the narrow-reef environment.The purpose of the following investigation was to evaluate the viability of pumpable emulsion explosives for use in South African narrow-reef mining operations. By approaching the problem from multiple perspectives, this research aimed firstly to propose a theoretical framework and suite of equipment suitable for the implementation of pumpable emulsions within the narrow-reef environment. Through the development of this suite of pumpable emulsion technology, tests could be undertaken on the proposed narrow-reef emulsion formulation and pumpable emulsion technology to obtain the necessary understanding of the performance of the system under controlled operating conditions prior to its implementation in the broader mining industry."

Jan 1, 2015

By A. A. Debrah

Artisanal and small-scale mining (ASM) plays a fundamental role in the national and local economies of resource-rich countries in Africa. As such, more effort must be geared towards fostering this type of economic activity to sustain livelihoods in rural communities. Across Africa, efforts to operationalize ASM based on a sustainable development framework have been quite tedious and often ineffective. This is because most of these frameworks lacked context and an understanding of the continuum from the artisanal through small-scale and up to the junior miner, grouped under the general term ?ASM?. Driven by the need to contextualize some of the definitional issues in this niche sector, and gain a clearer understanding of their peculiar challenges, this paper aims to contribute to the debate on ASM by considering two of Africa?s resource-rich countries ? Ghana and South Africa. Since South Africa has made greater inroads in protecting the interests of small-scale miners, we thus draw comparisons from both countries? approach to ASM, outline the lessons learnt, and provide recommendations regarding the ways forward.

Jan 1, 2014