Search Documents

By Hans Perlid

In the handling of emulsion explosives pumping is a key operation. A number of serious accidents has shown that pumping can be a risky operation and should be care&lIy considered and investigated. This is the background behind a series of pump tests carried out by NTTRO NOBEL.

Jan 1, 1996

By Michael Swisdak, John Tatom, James Tancreto

In 2002, testing was proposed to generate needed data to assist in developing improved explosives safety standards within the US Department of Defense. This testing emphasizes two major areas: (1) full-scale donor/acceptor trials examining debris generation and acceptor response and (2) debris perforation testing of representative roof/wall materials. The full-scale donor/acceptor trials are referred to as the SciPan series. The first three tests in the SciPan series have been completed, as has the first phase of the SPIDER program. This paper describes the status and future of these testing programs, reasons for choosing specific tests, potential benefits, and planning for future phases.

Jan 1, 2006

By D. Mason, W. J. Birch

Blasting operations are arguably one of the most contentious areas of surface mining.Many operators carry out outine monitoring as required by Mineral Planning Authorities. However in so doing they only concentrate on the observed Maximum Peak Particle Velocity (PPV) being below the statutory limit and pay little or no attention to the measurable parameters that determine this value (e.g. scaled distance, burden, detonator type, blast type or rock type). Such practice is “monitoring to comply”. What is needed is for the operators to adopt a methodology that clearly demonstrates to the appropriate regulators that the operator is “planning to comply”. The aim of the exercise being to deliver a process that is seen to be transparent, accountable, and quantifiable, which seeks to minimise environmental impact whilst not compromising the efficiency of the blasting operations mine.

Jan 1, 2011

By T Weaver, R Dick, R Sivakumar, C T. Aimone

A series of small-scale crater tests were performed in concrete and sand in an effort to understand the cratering process in large-scale field blasts. The surface orientation of these tests varied from flat to a 30° slope. In comparison to previous crater experiments in competent oil shale, the crater tests in concrete produced craters similar to those in oil shale after scaling the measurements for differences in the mass of explosives among the experiments. Material strengths and the degree of brittleness had a significant effect on the size and shape of the crater. The small-scale sand tests resulted in some crater features that were similar to large explosive tests in alluvium and soil.

Jan 1, 1986

By Sandor Nagy

The Explosive and Blasting Department of the Hungarian Mining Research Institute is responsible for the research and development of industrial applications of explosives. Appropriate explosives technology is developed for each application, including the explosive demolition of structures, which belongs within our charge.

Jan 1, 1977

By Janice Reed

The first seismograph was developed around 132 AD. Much has happened since then. The “modern” seismograph (> 1920) has seen a lot of changes. From falling pin seismographs to magnetic tape units to today’s Z-curve analysis models, the blasting seismograph remains a necessary and useful tool to the blasting community. But why so many changes? What forces drive the advancement of the seismograph? There are many answers and aspects to this question. Research, regulation, and technological advances are the primary forces behind innovation in our industry. But these three forces also drive each other. Research drove our industry from displacement seismographs to particle velocity seismographs. Technology took us from 80 pound seismographs to units weighing less than 5 pounds. Regulation (and litigation) - the driving forces behind the Z-curve analysis units. How have these innovations helped today’s blaster? Have there been any negatives? It is important for today’s blaster to understand how we got here and why.

Jan 1, 2005

Bloomfield Collieries Rix’s Creek Mine is an open cut coal operation located in the Hunter Valley region of Australia. The mine produces approximately 1.1 mt of saleable product per year and routinely employs cast-blasting practices for its unique dragline-truck overburden excavation method.

Jan 1, 2006

By Sharon K. Reamer, Klaus G. Hinzen

A series of controlled seismic experiments was performed in a limestone quarry in southern Germany to study seismic effects of cylindrical charges fired in both a half space (HS) (burden 63 m) and quarter space (QS) (burdens of 3 and 3.5 m) geometry. Charge columns contained from 20-32 kg of explosives and initiated from the bottom. The explosives formed a cylinder 4 m (20 kg) and 5 m (32 kg) high and 90 mm in diameter at depths from 3-8 m below ground level. Prior to each of the larger explosions, small charges of 0.12 kg seismogelit were fired at 4 m and 8 m depths in the same boreholes. Seismograms were obtained from 23 three component surface stations and up to 10 three component borehole stations (6 m depth). For each experiment, stations were located on three linear profiles of length 72 m at different azimuths from the source and one semicircular profile at a constant range of 30 m.

Jan 1, 1991

By Calvin J. Konya

Many controversies and differences of opinion exist in blasting technology. The primer location in small diameter dynamite columns is an example of one of these controversial areas. It is generally agreed that in rotation firing of small diameter blastholes, primer placement near the bottom of the borehole is beneficial since it reduces the likelihood of cutoffs. The controversy results in the actual location of the primer in the bottom of the blasthole. Some references indicate that the primer cartridge should be the first cartridge in the bottom of the hole, with the cap pointed toward the collar of the hole. Others indicate that performance is improved with no sacrifice in safety by placing a tamped cartridge first in the hole, and the second cartridge being the primer. The following investigation provides some factual data for consideration.

Jan 1, 1980

By Frank Lucca

This study is based on a six month study performed for Lee County, Florida. The study was based on blasting for land development and how this type of blasting affects structures. The study is investigates peak particle velocities and the relationship to other environmental and manmade forces that affect structures. The study also explores the effect of geology on blast vibration. After completion in Lee County, the study was then continued in the quarry environment in Vermont and extremely tight blasting environment of New York City. Charge diameters were 127mm (5 inches) or less.

Jan 1, 2006

By Miguel Araos

The aim of this study was to understand clearly how VOD of emulsion-based gassed explosives is influenced by parameters such as nitrate salt composition in the oxidizing phase, product density, blend composition, gassing rate, type of sensitization, etc. Also some VOD testing was performed on watergel-based gassed explosives in order to compare the results with those obtained for emulsions. VOD measurements were conducted in the surface blasting facility at the Research and Development laboratory of ENAEX SA (Calama, Chile). Despite the fact that the influences of some parameters on VOD of emulsion-based gassed explosives are easily predicted, there was found to be an unexpected correlation. Although it is commonly believed that the VOD of gassed explosives depends on the density, this study found that the VOD depends on the both size and the amount of gas bubbles incorporated into the product as well as type of sensitisation, regardless of whether the explosive was straight emulsion or a blend. Density is just a consequence of the incorporation of voids into the explosive. Future work in this area may examine variation of other parameters, in order to obtain a greater knowledge of detonation properties and therefore to design more efficient explosives.

Jan 1, 2002

By L D. Lawrence, R S. Day, Gordon Coleman

Commercial emulsion explosives are typically characterized by their relatively high detonation velocities due to the intimacy of oxidizer and fuel and to their sensitization with glass microballoons. However, numerous blasting operations in softer, more porous rock formations are better fragmented with slower shooting explosives. Although mixtures of emulsions with large amounts of ANFO (60-80%) can considerably reduce the high velocities, little water resistance is achieved with low levels of emulsion blended with ANFO. "Water proof" blends containing typically 50 percent of emulsion become quite costly due to escalating powder factors in ANFO patterns. Blends of sensitized emulsions with 20-30 percent ANFO retain the high velocity characteristics of the emulsions as well as increased densities which can also adversely affect blasting results in softer rock formations. The introduction of a reliable and predictable on-site gassing process for sensitization and density control of repumpable emulsions, with or without added ANFO, offers the end user the option of supplying a final product more suited to his blasting needs. The capability to widely vary final product loading densities and consequently product detonation rates better tailors the final explosive to different rock characteristics. The beneficial advantages of this system in softer rock formations have been well documented. Overall comparison between these variable density products with typical repump emulsions containing solid density control will be reviewed. Besides the obvious cost advantages and safety advantages of these systems the end user is provided more definitive control of his blasting operation.

Jan 1, 1990

By Josephine Bones, Robb Larson, Daniel Miler

Avalanches are commonly mitigated through the use of explosives at ski resorts and above transportation corridors. Surprisingly, very little research has been conducted on snowpack response to explosive inputs, and efforts to model this response have been limited. The purpose of this ongoing research project is to ascertain an understanding of the dynamic snowpack response in relation to explosive size and height above the snowpack, coupled with snow conditions, to enhance avalanche control. A system of sensors and computer-controlled data acquisition components has been created to record the movement of snow resulting from the charge detonation. The system records acceleration vertically and radially within the snowpack at two distances from the point of detonation as well as blast air pressure at one location during explosive events. The data at two locations allows inferences to be made about the transmittance and attenuation of shock waves through the snowpack radially as well as vertically. The data shows that raising charges above the surface results in increased snowpack dynamic response when compared to surface detonations. Applying power function regression to accelerations for individual charge elevations, it was determined that both radial and vertical rates of attenuation were not dependant on charge elevation. Additionally, raising the charge also resulted in increased dynamic response at depth within the snowpack

Jan 1, 2012

By R E. Langston, S M. Gazioglu

A preconstruction inventory program was conducted to determine the existing conditions of residential, non-residential and all other structures within 2,000 feet of the blasting limits for a highway excavation site in Asheville, North Carolina. Prior to major production blasting, eleven test blasts were detonated to establish site specific propagation parameters in order to develop contours of maximum allowable explosive charge weights per delay. The method of scaling distance by the square root of charge weight per delay was utilized in developing the contours of allowable charge weights. The charge weight contours were revised during blasting operations as additional vibration data became available. The effects of blast induced vibrations on a nearby water storage reservoir, a nearby vehicular tunnel and other adjacent residential and non-residential structures were observed and monitored over a period of two years of blasting operations.

Jan 1, 1980

By R L. Keller

Hong Kong has some of the most restrictive practices regarding blasting than any place in the world. Regulations regarding vibration limitations are 1 in/sec for structures and 0.5 in/sec (or even less) for most utilities; with no recognition of frequency response or adjustment. The Hong Kong Geotechnical Engineering Office has one of the most conservative approaches and protective guidelines for pre-blast assessment of slopes subjected to blast vibration (SEE paper '96). The protective measures to control flyrock generally required by the Mines Division are additionally very stringent. It is not uncommon for the costs associated with protective measures or methods which must be employed to exceed the cost of the drilling and blasting itself - or to waiver blasting application unfeasible altogether. From these restrictions it can easily be imagined how blasting in this urban environment would be most challenging.

Jan 1, 1997

By Cameron McKenzie

Flyrock is a complex issue involving interaction between the charging crew, the blast design, and the local geology, and once conditions on the shot meet certain criteria, the probability of a flyrock incident becomes unacceptably high. It is essential that flyrock awareness be built into the blast design process, requiring an engineering approach to understanding and controlling the outcomes and managing the associated risks. Based on previous studies of flyrock and published literature relating to fragment motion at high velocity in air, the equations to predict maximum flyrock range, and the size of particle achieving the maximum range, for blasts of varying rock density, hole diameter, explosive density, and state of confinement have been developed. These equations, and other associated correlations, permit the flyrock footprints to be established for any charge configuration, in any size blasthole, in rock of any density, and with particles of any known shape factor. The equations developed, and the mechanisms they reflect, allow engineers to go a long way towards understanding the primary factors controlling flyrock generation, including the rock mass, the blast design, and the quality of blast design implementation, i.e. the human factor. The paper presents guidelines as regards use of the equations to establish personnel clearance distances as a function of charge design and implementation, and equations to estimate appropriate stemming lengths when blasting must be conducted close to occupied or sensitive structures. The equations are amenable to definition of, and quantification of Flyrock Risk.

Jan 1, 2009

By V R. Sastry, D P. Singh, N R. Thote

Rock parameters which are uncontrollable impose restrictions on the procurement of desirable fragmentation. Blast design parameters which are controllable prove to be important tool in blasting operations. An attempt was made by the authors to investigate parameters which causes big oversize boulders in overburden blasting. A case study of coal mine is discussed in this paper.

Jan 1, 1995

By D Wilson, E Nagy, R A. Augsten, R R. Vandebeek, R L. Guilbeault

The Canadian Explosives Research Laboratory (CERL), is evaluating the status of the Schedule IV explosives container as it presently pertains to the industry. The Schedule IV container serves the same purpose in Canada as the IME 22 container does in the United States. That is, to transport detonators on the same vehicle which is carrying explosives.

Jan 1, 1990

By Charles Zdazinsky

Back-break induced from blasting is a concern in open pit metal mining because it compromises the conditions of the pit’s final walls. Final walls that have excessive blast induced damage commonly require extra attention and can often lead to increased cycle times. Most importantly however, the safety conditions of a back-broken region can be significantly compromised and it must be addressed to prevent injury and/or damage to equipment. This occasionally results in the necessity to alter mine plans to prevent an incident from occurring in a back-broken region which can be costly to the mine.

Jan 1, 2014

By Sterling Ziegler, Kameron Ray

Mining operations at a Wyoming coal mine were progressing to within 300 feet (91 meters) of a high pressure natural gas pipeline. Vibration levels from cast blasting were at a point at which standard designs would exceed permitted limits and could potentially damage the pipeline. Without a confident vibration model, mining would be unable to continue in the pit rendering an entire cut of otherwise mineable coal sterile. To safely blast in the area, linear superposition seedwave analysis techniques were attempted to be used to create a model that could accurately predict the vibration at the pipeline. Four signature holes were fired individually. The four signature waveforms were monitored at eight discrete locations to create thirty-two vibration data points. Two of the monitors were equipped with triggers enabling the calculation of p-wave velocity.

Jan 1, 2018