Search Documents

By Fred W. Stiefel

This paper covers the operation and maintenance of Diesel locomotives underground on a portion of the Delaware River Aqueduct. † This part of the tunnel is 15 miles long, with shafts 14 ft. in diameter spaced about 5 miles apart. These shafts (2, 2a and 3) are 825 ft., 1551 and 840 ft. deep, respectively. The grade of the tunnel is almost level, except for the 12,100 ft. north of shaft 2, which has a grade of 2.31 per cent. The tunnel is circular, 17 to 19 ft. in diameter. It lies at a depth of 400 ft. below sea level, with a maximum overburden of 2400 feet. The tunnel driving was carried on in six headings, using 15 storage-battery locomotives, each of 13 gross tons and having a maximum speed of 8 miles per hour. The longest haul was 3 miles, which proved to be the maximum distance for which storage-battery locomotives could be employed economically for the amount of material to be moved. One locomotive was used for switching cars at each heading, one for switching cars at the bottom of each shaft and one on the main-line haul from the heading to the shaft. The maximum amount of material hoisted in one shaft from two headings when 104 ft. of tunnel was driven in 24 hr. was 1000 cu. yd., or about 2000 tons of rock in place. The total quantity excavated was 750,000 cu. yd. (1,500,000 tons of rock). The tunnel-lining operations using concrete presented a problem of hading a maximum distance of 5 miles in the tunnel. The concrete-placing equipment had a capacity of about 2000 CU. yd., or 4000 tons in 24 hours. Experience had shown that storage-battery equipment could not handle this quantity of material within the time required at the distance of 5 miles. Trolley-locomotive haulage was considered dangerous and expensive, and would cause interference because transmission equipment would be required. Therefore the performance of Diesel locomotives of 160 hp., with a speed of 18 miles per hour, in comparison with that of other types of locomotives, was studied. Choice of Locomotives In deciding upon the type of locomotive to be used for the 5-mile haul, four alternatives were considered, as follows: I. To purchase additional storage-battery locomotives with the necessary batteries over the 6 locomotives and 12 batteries available. 2. To convert the existing battery locomotives to the trolley type. 3. To purchase new trolley locomotives. 4. To purchase Diesel locomotives. Proposition No. i The 90-hp. storage-battery locomotives the (each weighing about 12 tons), when hauling a load of 64 tons, with a drawbar pull of about 1900 lb. on a level track, developed a speed of 8 miles per hour and could make five round trips in 8 hr. with a

Jan 1, 1943

By C. M. Marquardt

Tramp iron and steel moving on a conveyor belt cause small currents to be generated in a coil situated in a strong magnetic field, which are converted to an alternating current and are amplified. The output voltage from the amplifier fires a thyratron with a relay in its anode circuit, which actuates a howler and simultaneously drops a spot of marker material on the belt. THE problem of tramp iron removal from moving ore belts is a long standing one. When heavy ore streams are carried on a belt, magnetic pulleys and strong surface magnets fail to remove tramp buried in the ore stream. Tramp iron buried in the ore stream cannot be pulled from the bed by surface magnets and is carried past the magnetic pulley by the falling ore stream. With the increased use of detachable bits the problem of the detection and removal of tramp has become more necessary and difficult. Several types of tramp detectors have been developed. It would serve no practical purpose here to review exhaustively the literature on the subject. Methods of tramp detection used are: (1) The magnetic method, wherein the small current generated by the magnetized tramp passing a Coil is used. (2) The unbalanced oscillator method wherein the tank circuit of a stable radio- or audio-frequency oscillator is unbalanced causing a change of frequency or a change in plate current due to changes in eddy currents, hysteresis, or dielectric because of the presence of tramp. (3) The bridge methods wherein the impedance of one leg of an alternating current inductive bridge is changed due to the presence of conducting tramp. Each of these methods of tramp detection has its field of usefulness. The second and third methods are excellent for oxide iron ores, coal, sand and gravel, grain, etc. However, these latter methods are not suitable for use on ores that contain rich conducting sulphides, since a large piece of pyrite or galena will cause the same detector response as a piece of tramp iron. At the Caselton, Nevada, plant of the Combined Metals Reduction Co., sulphide ores are treated; therefore, it was necessary that a tramp detector operating on only the magnetic properties of the tramp iron be used. Tramp iron detectors of this type operate on the principle that if a piece of tramp iron moves near a coil in a high intensity, steady magnetic field, the presence of the moving tramp iron causes the magnetic flux lines through the coil to change. This induces a mall current in the Coil. In series with the Coil is generally placed a relay sensitive to currents of 1 to 3 microamp. When the tramp iron passes near the coil the flux linkages change, causing this very sensitive relay to actuate. Since the contacts of such a relay are very small it must actuate a second relay capable of breaking a larger current

Jan 1, 1951

By William T. Schneider, Taylor Cole

Drilling in West Texas during 1941 was more active than in any year since 1937, a total of 2325 wells having been drilled. Pre-Permian exploration was the greatest in the history of the area; 106 wells tested pre-Permian formations during the year. Wildcatting reached the peak since 1937, with 135 wildcats, of which 20 per cent were producers. The wells were drilled to a greater average depth than in any previous year. Slim-hole drilling was the common practice, using drilling equipment that is largely portable. Because of deeper drilling, more attention was paid to mud fluids, especially the use of materials to reduce water filtration. There has been slight improvement in the protection of the pay horizons while drilling by the use of reverse circulation, and drilling-in with oil as well as low water-filtration muds. The practice of setting and cementing the oil strings through the producing formation and perforating opposite the pay zones has increased in the fields producing from sands. It is doubtful whether this practice is of unusual value in dolomitic limestone fields. There have been few if any technological improvements in obtaining necessary information on the pay sections penetrated, by coring, core analyses, better sampling, and more detailed drilling time. However, more operators are beginning to realize the necessity of good samples. For a proper study of the reservoirs in West Texas, it is essential that better samples be obtained, that more core analyses be run, and that better methods of obtaining drilling time be initiated. It should be noted that increased drilling speeds and slim-hole drilling have tended to reduce coring and core recovery and have not aided in obtaining good subsurface samples. In fact, fast drilling speeds and slim-hole drilling have reduced the cost of drilling operations, but with the sacrifice of much needed subsurface information. Larger quantities of slower-reacting acid are being used per well. There has been improvement in shooting, in that a greater number of quarts per foot have been used and an attempt has been made to concentrate the shots opposite the pay zone. The use of mud logging to determine the characteristics of the pay section increased considerably over the year 1940. There has been a slight increase in obtaining reservoir information in the new fields, such as bottom-hole sampling, bottom-hole pressures, and records of gas, oil, and water withdrawals. However, there is great need for more data on these subjects, particularly accurate information regarding gas and water volumes. There are three repressuring projects and a fourth is nearly ready for operation in the Kermit field. There is one repressur-ing project in the Payton field and one in the North Ward field. So far, the gas-injection projects have not shown very impressive results. As yet, there are no water-flooding projects or water-disposal projects in West Texas. Not including gathering lines within the fields, 222 miles of feeder pipe lines were

Jan 1, 1942

By H. R. Nelson, Martin S. Maier

The diffusion of metals plays an important role in many metallurgical processes,lJ as, for example, the formation of alloys by the annealing of mixed powders, the homogenization of segregated alloys, and the carburization of steel. Other equally important phenomena, such as recrystalli-zation and creep, are based on the movement of like atoms. Although much is known concerning the effects of diffusion in metals, very little is known concerning the details of the physical processes involved. 1,3-5 The data that should give most information concerning the processes involved in diffusion are those on the diffusion of like atoms—self-diffusion. Very little is known concerning the rates of self-diffusion of metals because before the discovery of artificial radioactivity in 1934 there was no means of detecting the movement of the diffusing atoms through the solvent metal except in the elements possessing natural radioactive isotopes—lead, thallium and bismuth. Using the induced radioactivity of the element as an indicator, atoms can now be "tagged" so that the rate of diffusion of the radioactive isotopes of an element (tagged atoms) into the stable isotopes of the same element can be measured. As the radioactive and stable isotopes of an element differ only in nuclear structure, it is quite certain that all isotopes of an element diffuse at the same rate. Two techniques have been used to measure self-diffusion. In one, a thin layer of radioactive metal is deposited on the face of the solvent metal, and the decrease in the surface activity as the radioactive atoms diffuse into the solvent metal is measured. This method has been used to determine the coefficients of self-diffusion of lead6-l0 and bismuth10 using natural radioactive isotopes, and of gold1' and copper12 using artificial radioactive isotopes. In the other technique a thin layer of the radioactive metal is deposited oil one face of the solvent metal, and after diffusion has occurred the specimen is cut in thin sections to obtain the concentration-penetration curve. This method has been used to determine the coefficients of self-diffusion of gold,13 zinc,14-l6 silver," and copper.17 The second method was used for the work described in this paper. Materials The coefficients of self-diffusion were determined in two grades of polycrystalline copper and in single crystals of copper. Commercial OFHC copper was used in the form of disks I in. in diameter by % in. thick. Samples of high-purity copper described by Phillips and Skinnerl9 were supplied through the courtesy of the American Smelting and Refining Co. The high-purity copper rod was used without remelting by cross-rolling to a thickness of 0.075 in., from which disks 7/8 in. in diameter were cut. A good grade of bus-bar copper was used to make the single crystals.

Jan 1, 1942

By E. D. Hummer, J. A. Younkins. J. P. Proctor

Comparatively little has been published relating practical experience with the control of the solid content of washery water systems that must be "closed." A "closed" system is one that for some reason may not be cleaned by the emission Of any effluent Of high ''lid 'content to be rep1aced by 'lean water in Order to hold the solid content of the waste water within reasonable bounds for efficient washing. It is the Purpose of this Paper to describe practical experience with such a water system and to present data that it is hoped may be of some use to those who are faced with a similar problem. The washery clarification system described comprises three thickeners and three filters, and although it is admitted that each of the fields of water settling and thickening and filtration offers a wide scope for investigation, the authors are not attempting to present the answers to these problems but to set down the results of some experience along these lines, making no claims as to the ultimate solution of the problems in hand. The subject of water clarification has vast ramifications; for example, the science of flocculation as applied to water settlillg and filtering opens up fields of wide possibilities of which as yet little is known. A comparatively recent entry into the field of water treatment, which may offer possibilities of practical application, is the use of "wetting" agents such as "Aerosol." General Arrangement of Water System So that the reader may obtain a comprehensive picture of the factors concerned in the control of a closed water system, it is necessary to give a brief description of the washing plant that is serviced by the water system to be described in the following pages. As we are not primarily concerned with the washing plant in detail, only a brief description of the flow of coal as it relates to the water system will be given here. For a more detailed account of this type of washer, the reader is referred to earlier papers,1,2 The washer, which handles o to 4-in, raw coal (750 tons per hour) is an American Rheolaveur plant of two complements; the coarse coal or sealed discharge plant and the fine coal or free discharge plant. The sealed discharge plant (Fig. I) consists of twin 48.in. primary launders, each having two washing boxes, supplemented by one 32-in. rewash launder, which also has two washing boxes. "Push" water for washing and conveying coal in these launders is supplied from a constant-head tank under pressure head of 10½ ft. at the point of introduction at the feed end of the launder. This tank also supplies water for upward or vertical currents used in the Rheolaveur or washing boxes. Each box discharges into a sealed boot elevator (Fig. I).

Jan 1, 1942

By C. Williams, D. V. Carter

During 1943 five oil fields and two gas-condensate fields were discovered in the East and East Central Texas district. The New Hope field, discovered by Tide Water-Seaboard in Franklin County, is the most important oil discovery since the Hawkins field in 1940. At the close of the year two oil sands were producing and two additional oil sands were being tested. The gas-condensate fields of Appleby in Nacog-doches County and the Stewards Mill field in Freestone County had only one producing well each. The Carthage field was extended 3 miles north and 4 miles west. Another well that was testing at the year end indicated a probable eastward extension of several miles. The Quitman field, in Wood County, was the most active from the standpoint of drilling operations. Approximately 48 wells were complcted during the year. The second and third most active fields were Hawkins field, Wood County, and Kildare field, Cass County, respectively. Wartime restrictions of material, together with manpower shortage and Federal spacing regulations, reduced the number of oil and gas-well completions from 265 in I942 to 171 in 1943. This represents a drop of 35 percent, or approximately 1/3, enough to replace the 531 producing wells abandoned in the district during the year. No changes were made in the price of crude oil in the district in 1943. The district produced 177,652,940 bbl. of condensate and oil during 1943. This represents an increase of approximately 11 per cent compared with the previous year. The East Texas field, which is the largest and most important field in the district, had an annual production of 128,568,647 bbl. of oil, which is approximately 6.5 per cent more than the previous year, and represents 72 per cent of the district's production of condensate and oil for the year. The district had an estimated basic daily allowable of approximately 509,000 bbl. of oil on Dec. 31, 1943. The entire district produced approximately 30 pcr cent of the state's production for the year 1943. The Hawkins field, Wood County, was operated 271 days during the year and with an average daily production of approximately 52,488 bbl. for the year. This field, which is the second largest in the district, produced 14,224,164 bbl, of oil during the year. Changes in annual production in certain fields in the district can be attributed to their ability to produce at higher rates, the demand, and transportation facilities in the war effort. The East Texas field showed an over-all decrease in reservoir pressure of 8.30 lb. during the year. Indications were that through the first quarter of 1944 the return of salt water to the reservoir was having a beneficial effect. It is hoped that, as more and more water is returned to the reser-

Jan 1, 1944

By R. B. Gilmore

The North Texas district, as herein defined, includes the counties of Archer, Baylor, Clay, Cooke, Foard, Hardeman, Jack, Kiiox, Montague, Wichita, Wil-barger, and Young. Jack and Young Counties are included for the first time so that this district will correspond with District No. 9 of the Texas Railroad Commission. This area covers generally the crest and south flank of a system of buried mountains known as the Red River uplift. The oil and gas accumulations along this feature are in traps, which, although localized by structures incident to the regional uplift, usually are modified by stratigraphic changes in the sediments. The structural deformation caused by the Red River uplift is modified by the Rend arch, which is a broad anticline plunging northward from the Llano uplift in central Texas through Young and into Archer Counties. The fields in southern Archer, southeastern Baylor, southwestern Clay, and western Jack Counties arc on the extreme north end and along the flanks of the Bend arch and have generally the same type of oil and gas accumulation as the other fields in this district. Recent exploration has been along the flanks of the Fort Worth syncline, which is east of the Bend arch and south of the Red River uplift and extends into southeastern Clay and southwestern Montague Counties and along the eastern part of Jack County. The larger part of past oil and gas produc- tion has come from Pennsylvanian strata, with less important amounts lrom the Permian, and minor quantities from the Mississippian and Ordovician. Developments during 1943 About 1100 wells were drilled in the district during 1943 and more than 500 oil wells were completed, an increase from 1942. of approximately 12 per cent in the number of successful drilling operations of the total wells drilled. The addition of Jack and Young Counties to this district accounts for part of this increase, almost 150 wells being completed in the two counties. Production increased slightly over the previous year as a result of an increase in the number of producing wells and a greater demand for this high-gravity, sweet crude oil. The average depth of discovery wells was about 400 ft. deeper than in 1942. Although more discoveries produced from horizons below the base of the Strawn series than from those above the Straw, the deeper horizons, including the Bend series of the Pennsylvanian, the Mississippian limestone and Ellenburger of the Ordo-vician, largely were dissappointing from the viewpoint of major additions to oil reserves. The largest single addition to the reserves was in the basal Strawn sand in the Walnut Bend field, Cooke County. During the year, 31 wells were completed, both in the field and as cxtensions. The most active arca Was Jack County, in which five fields or potential fields were discovered, although only 44 oil wells were completed.

Jan 1, 1944

By Theron Wasson

The oil and gas fields of Michigan that have been under development since 1925 are in an area that extends across the middle of the lower peninsula from northeast to southwest, a distance of about 200 miles, and with a width of about 80 miles. In 19 years 70 fields have been discovered. Most of these are relatively small when compared with other oil-producing areas. This is borne out by the fact that since the first wells were drilled these fields have produced a total of only 204,000,000 bbl. However, Michigan is still maintaining its production, for during the past five years the annual production has remained fairly constant at approximately 20,000,000 bbl. Production for 1943, as reported by the Bureau of Mines, was 20,682,000 barrels. Roughly, one third oi Michigan's production in 1943 came from the Reed City field, which was discovered in 1941. During the year, 237 oil wells were completed in Michigan in 1943. The decrease of 56 from the 1942 total is probably due to the continuance of Government regulations requiring a 40-acre spacing pattern over most of the state. Fig. I shows the principal oil and gas fields of Michigan, and the columnar section, Fig. 2, shows the principal producing horizons in relation to the section drilled. The data of Table I and Table 2 have been carefully checked with previous reports to eliminate errors. Six new producing areas were discovered during 1943 and five areas discovered in 1942 were developed during the year. Both the new discoveries and the 1942 discoveries that were developed appear to be small and relatively unimportant. Goodwell Field.—The best discovery of the year is the Goodwell field, T. 14 N., R. 11 W., Goodwell township, Newaygo County. This small structure was located by core testing done by The Pure Oil Co. in 1942 and early 1943. The first producing well, C. R. Harris No. I, was completed on July 5, 1943, ill the Traverse limestone at a total depth of 2742 ft., with ail estimated potential of 1100 bbl. per day. By the end of the year, 18 wells had been completed in this field and approximately 281,000 bbl. of oil produced. The field operated under proration of 262 bbl. per day per well from Oct. I to Dec. I; 150 bbl. per day per well after that date. Woodville Field.—The small Woodville pool, T. 15 N., R. 11 W., 3 miles north of the Goodwell field, was discovered by core testing by the Ohio Oil Co. The discovery well was completed on May 5, 1943, flowing 650 bbl. of fluid, including 18 per cent salt water the first 18 hr., from the Traverse limestone at a depth of 2810 to 2815 ft. Seven wells had been completed by the end of the year and 67,000 bbl. of oil had been produced. Development is now practically at a standstill because further drilling does not aDDear economically iustified.

Jan 1, 1944

By C. R. Dale

The need for instruments to measure the movement of fluids and gas in wells has been recognized by engineers for many years. Information regarding flow in the producing interval has a direct bearing on completion practices in new wells and also provides information on the production characteristics of the well. Many hours of engineering time are spent in planning and completing wells but knowledge as to whether or not the original planning has produced the desired results has not always been complete. Many questions such as the following often arise: Why is it that two wells are completed under supposedly identical conditions, yet one well is a good one and the other is a poor one? Are the sands that look the best on the electric log contributing to the production? These and many other conditions in the producing well need to be under- stood in order to develop more efficient production practices and to improve on methods of completing new wells. It is the purpose of this paper to briefly describe one type of instrument, outline the methods of running the equipment and show the results of surveys made under various conditions. With an understanding of the use of this type of survey its importance can be evaluated in relation to the problems encountered by the operator. DESCRIPTION OF INSTRUMENT The instrument is a velocity recorder employing a clock-controlled 16mm film for recording the rpm of an extremely sensitive rotor which is rotated by the flow of fluids or gas in a well. The helical-vaned rotor and shaft, weighing one-half of one ounce are an integral unit exposed to the well fluids and are the only moving parts not enclosed in the fluid-tight housing. No packing or fluid seal of these parts is necessary and the shaft is mounted top and bottom on special jeweled bearings. Fig. A is the lower part of the instrument showing rotor and shaft with the protecting housing sleeve removed. The rpm of the rotor is recorded on the moving film by a combination electrical and optical system. The record is a series of dashes on the film, each dash and space representing twenty (20) revolutions of the rotor. (Film record of survey made in California well showing station recordings at various depths.) As the movement of the film is controlled by the clock the number of dashes and spaces in one minute of film travel represents the rpm of the rotor. The range of the instrument is from 0 to 2,500 rprn. The barrel or housing is 1-11/16 in. OD and seven feet long. Various types of expanding fluid traps are attached to the lower end of the instrument to direct the flow through the 1 in. orifice containing the rotor. The fluid trap for upward flow is shown in Figs. B and C. This assembly consists of eight arms with light spring

Jan 1, 1949

By R. G. Patterson

The usual procedure in determining the magnetic susceptibilities of rocks and formations has been to take samples in the field and measure their volume susceptibilities in the laboratory, using one of numerous methods available. In none of these methods is the measuring instrument suited for field use. Usually the sample is pulverized; sometimes it is machined to a desired sue and shape, and in one method1 a cast of the sample is made and the susceptibility of the rock compared with that of a material of known susceptibility of the same size and shape, made from the cast of the original sample. Some writers assert that the difference in susceptibility of a rock sample in powdered and solid forms is negligible, and while doubtless this is true in many cases there are others in which the difference becomes appreciable. Further, the susceptibility of a small specimen may differ from that of the rock from which it is taken, owing to the stresses produced by the hammering or other forces used to obtain the sample and shape it for testing. Wilson2 found that an individual specimen of granite had about the same susceptibility in the solid as in the powdered form, but that pieces from different parts of the rock varied as much as 750 per cent because of unequal distribution of magnetite. The most accurate value of susceptibility would, obviously, be obtained from averag- ing a number of tests on the undisturbed rock instead of from one or two samples. No such procedures have been published, to the writer's knowledge. It is the purpose of this paper to describe a method by which susceptibilities of rocks may be determined in place by means of a portable instrument. Method The principle involved in this new method is that there is a change in inductance of a coil due to the presence in its magnetic field of a paramagnetic or dia-magnetic medium. In this case, however, the windings of the coil do not enclose any part of the rock under test. Instead, the coil is circular, being small in cross section as compared to its radius, and consists of several hundred turns of fine wire. It is placed flat on the rock of which the susceptibility is to be measured. Thus only part of the magnetic field from the coil penetrates the rock under test. The relation between the change in field strength or inductance of the coil and the susceptibility of the medium will be developed later. To measure the change in the inductance of the coil due to the presence of a magnetic material an alternating-current inductance bridge was chosen. Description of Apparatus Of many alternating-current bridge methods applicable,3 the one shown in Fig. 1 (Owen's bridge') was adopted for its simplicity and sensitivity. In Fig. I, the test coil is indicated by PlL1. It is connected to the bridge by about

Jan 1, 1946

By J. C. McDonald

A DDITIONAL experimental data are presented in this note on a phenomenon which has been touched on but lightly in the literature. The common magnesium base rolling alloy (AZ31B) contains about 3 pet A1 and 1 pet Zn. When cold rolled, it hardens until it starts to break up in the rolls at 30 to 50 pet reduction. When it is heated after rolling to full hardness, it softens. However, other magnesium alloys have shown themselves capable of being cold rolled indefinitely, provided the ratio of roll diameter to starting gage is sufficiently high. As measured by the tensile test, these alloys actually soften when the reduction becomes large (60 to 90 pct). A subsequent heating at 300' to 500°F can produce hardening of this metal. Heating at higher temperatures (600' to 800°F) causes recrystalliza-tion and softening. Menzen' has shown that a magnesium base alloy can be cold rolled without intermediate anneals as much as 90 pet. The alloy studied, Mg-1.5 pet Mn, softened considerably between 20 and 90 pet reduction, as measured by tensile properties; a decrease in yield strength of 30 pet, and an increase in elongation from 3.2 to 16.7 pet (longitudinal direction of the sheet). However, Menzen gives no data on the reaction of this metal. to heating. Ansel and Betterton2 and Hurst and Hatch3 report a similar effect in Mg-1.5 pet Mn-0.1 pet Ca. Their data show an initial hardening, followed by softening. The former authors also show that the alloy softened by cold rolling will harden when heated at low temperatures, and that these effects are absent in Mg-3 pet Al-1 pet Zn. In the course of work4, 5 some years ago, the author observed similar effects with alloys containing cerium, thorium, or zirconium; but not with elements like aluminum, silver, or zinc. Table IA contains the results of an experiment which shows these effects rather well. A binary alloy with 0.3 pet total rare earths (Mischmetal* added) was rolled hot to 1/16 in. and then annealed to full softness by heating 30 min at 800°F. Rolling was continued at 1.5 pet per pass to 80 pet total reduction on 8 in. diam rolls. The metal was harder after 20 pet work than initially but, at 80 pet reduction, properties were back to their original values. Heating for 1 hr at 450°F produced about the same hardness whether the reduction was 20 or 80 pet. At intermediate reductions, the metal hardened, but not to as high values. Extensive cold rolling may also be carried out on metal hot rolled at temperatures sufficiently low to produce a semihard temper. Mg-0.6 pet Zr was rolled to 0.1 in. at 700° to 800°F, 30 pet per pass. As shown in Table IB, a further cold reduction of 85 pet, at 1.5 pet per pass, definitely softened the metal.

Jan 1, 1959

By W. A. Boyer

If the safety factor of a mine hoisting rope is checked for the lowest depth, is the rope then safe for all levels? The answer here is no. A new set of volues is proposed. HOISTS for metal mines are seldom designed for one particular depth. They are intended for an ultimate load and depth with a given speed but are first used to hoist from a shallower depth, gradually working to the ultimate as development progresses. Sometimes the mine is not worked on the upper levels because of the kind and grade of ore, the mining of which depends on market conditions. In this case the hoist may be used in the same working shift to lift ore, for example, from the 1200 and the 4400-ft level. This means that the safety factor of the rope should be considered not only when it hoists from the greatest depth, but also when it hoists from the upper levels. According to present safety factor standards, a hoisting rope can have ample safety margin when hoisting from the lower or lowest level and still be shy of sufficient safety margin when hoisting from the upper levels. This will be shown by curves presented in this paper. The safety factor of a hoisting rope as defined by the U. S. Bureau of Mines' is the ratio of the static load to the tensile strength of the rope. It is calculated by dividing the breaking strength of the rope* In Fig. 1 curves A and B are plotted against the vertical suspended distance, which is the abscissa, and the factor of safety, the ordinates. Curve C is a smooth curve drawn through the midpoints of the steps of curve A and would more closely represent the minimum factor of safety for new rope for any particular depth. Curve D is a smooth curve drawn through the midpoints of the steps of Curve B and would more closely represent the minimum factor of safety when ropes should be discarded for any particular depth. If a new rope were applied with a minimum factor of safety, then the vertical distance or ordinate under curve D for any particular depth, divided by the vertical distance or ordinate under curve C, would represent the minimum percent of remaining area intact that could be allowed before the rope would be discarded. Also, that section of the ordinate between curve C and curve D is proportional to the section of the area of the new rope that could be allowed for wear and broken wires. Considering that point at 2500 ft on the chart, the ratio do to co would be the minimum percent of rope area remaining at the point of discard. The ratio of that portion of the ordinate cd to co would represent maximum percent of area of a new rope available for wear and broken wires.

Jan 1, 1955

By A. D. Dorenfeld

Factorial design is a mathematical method of drawing valid conclusions from a series of tests made in a predetermined pattern. It is applied to flotation ore testing using, in this case, five variables, each varied twice, requiring a total of 32 tests. Representative conclusions are checked by repeat testing. THE factorial design method of testing is particu-J- larly applicable to mill-scale plant tests because 1—the conclusions take into consideration all variabilities of the plant, 2—there are no subjective guesses as to the conclusions, 3—the number of tests necessary to check large numbers of variables are at a minimum, and 4—interactions between variables can be discerned. It is equally applicable to laboratory testing because once the variables to be investigated have been decided upon, as well as the number of levels for each variable, a well-trained assistant can run the tests, since the test work follows a predetermined mathematical pattern, leaving the conclusions to be found by the person in charge. The conclusion takes into consideration all errors of the tests. To illustrate the use of factorial design, a sample of copper porphyry ore was tested, the copper content of the batches not being uniform. Five variables were investigated, each at two levels, requiring only 32 tests. After suitable arithmetical analysis, conclusions for copper recovery and concentrate grade are arrived at. Four cases of these conclusions are checked by repeat testing. Testing Methods Reproducibility of flotation tests varies widely, depending on the experimenter, the process, the equipment, and probably a host of unknown and perhaps interacting variables. If the reproducibility of tests is good, let us say to 0.2 pct recovery of a certain metal, and the minimum difference between tests upon the variation of the interested variables is, say 1 pct, then simple averaging and inspection is ample in interpreting results. However, often such a happy situation is not the case. This is particularly true in mill-scale operations where the ores are variable, and a host of minor operating fluctuations common to most milling, and familiar to all mill operators, is the normal state of affairs. Yet, mill scale tests are run, the results averaged, and conclusions drawn therefrom. The trustworthiness of such results should be measured by comparison to the experimental error—the measure of the degree of reproducibility of the results. This comparison is a test of significance. Thus, if daily results of recoveries average 80.0 pct, and a spread of 78.0 pct to 82.0 pct, is recorded, then, clearly, on changing mill operations, an 81 pct recovery cannot be construed as significant by using averages, since it is well within the previous test limits. By using rigorous statistical tests of significance, conclusions arrived at by inspection or simple averaging may be shown to be based on inadequate evidence or even wrong. In any event, a plant super-

Jan 1, 1952

By G. T. Higgins

PREVIOUS workers1,2 have found evidence of exaggerated grain growth or secondary recrystallization on annealing sponge zirconium at temperatures high in the a, phase field, but no details of the orientation relationship between the secondary grains and "as-recrystallized" matrix were reported. In other hexagonal metals, namely dilute Mg-A13 and Cd-zn4 alloys, secondary recrystallization has been observed in which the secondary grains are related to the primary recrystallized structure by rotations about the c axis. These rotations are thus comparable with the rotations about the (111) axis observed in the secondary recrystallization of fcc metals. In the current work secondary recrystallization has been observed on annealing iodide zirconium at 800°C and the associated changes in crystallographic texture have been examined. The material employed was arc-melted iodide zirconium of the following composition: Impurity O H Fe Hf Pb I Ni C1 A1 ppm by wt 130 5 230 98 23 28 200 39 30 This was received as 0.25-in. plate, and, prior to the annealing studies, was cold-rolled to 0.040 in. Specimens 1 in. sq were chemically polished and annealed for various times at 800°C in a vacuum better than 5x 10-6 Torr. For metallographic examination specimens were first chemically polished and then anodized8 to enhance contrast between the grains when examined under polarized light. Changes in crystallographic orientation associated with the development of secondary grains were followed by (1011) and (0002) pole-figure determinations using a conventional Schulz goniometer in reflection. Filtered Cr Ka radiation was employed and great care was taken to avoid spurious re- sults due to the close proximity of the Bragg angles for the (1011) and (0002) reflections. Figs. 1 and 2 illustrate the change in grain structure on annealing at 800°C. After 24 hr the structure has ceased to be equiaxed due to the development of certain grains in preference to others. It is notable that the secondary grains do not grow to the extent observed in sponge zirconium.1,2 This appears to be due in part to the fact that normal grain growth is inhibited in the less pure sponge zirconium, with the result that the driving force for secondary recrystallization remains high, while at the same time the number of grains able to develop in the presence of the impurities is also smaller. As a consequence, in sponge zirconium those grains that do develop preferentially are able to grow into the fine -grained matrix without impingement, while in iodide zirconium the preferential growth of many grains leads to early impingement. The pole figures determined for specimens annealed for 5 min and 24 hr at 800°C are illustrated respectively in Figs. 3 and 4. These indicate that the dominant feature of the initial recrystallized texture consists of basal planes at an angle of 321/2 deg to the sheet surface, with a (1120) axis lying parallel to the

Jan 1, 1967

By Loyd R. Kern

A procedure for determining the behavior of a reservoir under a gas or water injection program was reported by Buckley and Levertt in 1942.1 This method, which allowed the calculation of the phase saturation distribution behind the front of a displacing fluid, has been extended to apply to a more general situation. The reservoir may initially contain flowing quantities of the displacing fluid, or the fluid in the reservoir may be above saturation pressure SO that solution effects are present. Production may occur behind the front as in the case of a well which is produced after breakthrough of the displacing fluid. The calculating procedure is simplified in that the graphical integration necessary to determine breakthrough saturation is eliminated by performing a direct integration and the graphical differentiation necessary to determine saturation distribution is eliminated by representing the displacing phase fraction of the flowing stream by an empirical equation. This representation results in simple expressions for the producing gas or water/oil ratio and cumulative production. INTRODUCTION A method for the calculation of the saturation distribution behind the front (interface between the displaced and displacing phases in a gas injection or water flooding operation) was reported by Buckley and Leverett in 1942. The method leads to a curve for the saturation distribution which is double-valued; consequently, part of' the curve was interpreted to be physically meaningless. That part of the curve which has physical significance was determined by a graphical integra-tion (material balance). In this paper it is shown that the integration may be performed analytically with a resulting equation for the saturation of the displacing phase at the front. The case in which the displacing fluid is initially flowing and the case in which the reservoir is initially above the saturation pressure so that some injected gas goes into solution are included in the integration. The calculations are considerably simplified by representing the fraction of the flowing stream which is oil by an exponential function of saturation. The methods is extended to apply approximately to reservoirs in which wells located between the injection well and the front are produced. An illustrative example utilizing the methods presented is included. RESERVOIR BELOW SATURATION PRESSURE In the case of a water flooding operation or in the case of a gas injection operation in which no gas goes into solution in the displaced oil, the equation for saturation in a linear flow system as a function of time and position as given by Buckley and Leverett is where* q = total reservoir volume flow rate, rvb/day A = cross sectional area of system, sq ft / = porosity of formation x = distance from injection point, ft t = time, days Pj = saturation of the displacing phase /dx velocity of planes of constant saturation, ft/day *The nomenclature used here is not the same as that used by Buckley and Leverett A complete nomenclature is given in Appendix A.

Jan 1, 1952

By J. M. Smith, D. Kunii, P. Adivarahan

Effective thermal conductivities were measured for seven samples of porous rocks through which gases or aqueous salt solution were flowing, parallel and countercurrent to the flow of heat. The results are analyzed in terms of the contributions of the solid and fluid phases to the total energy transfer. The solid contribution for the sandstone samples studied was found to be a Junction of the porosity and an effective thermal conductivity for the solid phase. The fluid contribution was a function of the Peclet number. Based upon the equations presented, the effective conductivity of the system can be estimated from the properties of the fluid, the flow conditions, and the porosity and pore-size distribution of the rock. INTRODUCTION Heat-transfer characteristics of porous media containing fluids are needed for the design and evaluation of thermal methods of petroleum production. The study reported here considers the problem of countercurrent flow of fluid and heat in sandstone rocks, and is a continuation of previous studies concerned with parallel and radial flow of energy and fluid in both rocks517 and beds of fine particles.6,10 In addition to these earlier works, Asaad,1 Kimura,4 Preston,8 Zierfuss and vlietll and waddams9 have reported effective conductivities for systems filled with stagnant fluids. There appears to be no published data on rocks through which fluids are flowing. The purpose of this study was to present such information and, particularly, to investigate the effects of properties of the rock and the flow rate on the results. The rock samples were naturally occurring sandstones from different locations and were similar to petroleum-bearing formations. The properties of the seven samples showing the range in porosities and permeabilities are given in Table 1. The mean pore sizes were calculated from mercury penetration data by averaging the radius with respect to pore volume. The details of this method and comparison with other procedures for estimating 7 are given elsewhere. Four fluids, nitrogen, carbon dioxide, helium and 10 weight per cent sodium-chloride solution were used with each sample. For Bartlesville sandstone, BA-5, runs were made at mean pressures from 15 to 250 psig using nitrogen. The other measurements were carried out at a mean pressure of 100 psig. The maximum temperature range eacountered was 70° to 300°F. The flow rate of fluid ranged from about 1.0 to 130 Ib/(hr)(sq ft), and this corresponded to a modified Reynolds-number range of 5 x 10-4 to 1.0. The variation in Prandtl number was 0.70 to 4.1. EXPERIMENTAL WORK The equipment consisted of apparatus to supply a constant flow of gas, or salt solution, at constant pressure to the bottom of a vertical test section, and metering and flow-regulation apparatus after the test section. The flow of salt solution was

By R. P. Fischer

A large production of vanadium during the war helped Germany to meet her critical requirements for the ferroalloy metals. Vanadium was needed not only in the ordinary high-speed too1 steels, but in other as a substitute for chromium, nickel, and molybdenum, which were scarce. Lacking a source of vanadium ore, however, the vanadium was obtained as a by-product of the steel industry—va-nadium-bearing pig iron smelted from iron ores containing about o. I per cellt V was blown in converters to yield vanadium-rich slag, from which vanadium was recovered by chemical treatment. The production capacity obtained was said to be about 6,500,000 lb. of vanadium a Year. Although the general Processes of Preparing vanadium-rich slags as well as the recovery methods described herein are known, some of the details presented may be of interest to both the American steel industry and the vanadium producers. No adequate data on the cost of the vanadium produced in Germany are known, but it seems likely that the cost exceeds the commonly quoted domestic price of about $1.10 per pound of contained VzOa. Information on the German vanadium production was obtained by a team of geologists from the Geological Survey* United States Department of the Interior, during investigations in May and June 1945 of the German utilization of low-grade raw materials. These investigations were sponsored by the Chief of Engineers, War Department. It is a pleasure to acknowledge the aid obtained from Messrs. H. C. Smith and J. D. Dickerson, investigators assigned to the Army Ordnance section of C.I.O.S., and Mr. C. F. Park, Jr., of the Geological Survey team. The data on vanadium recovery from iron ores were obtained from the Kaiser Wilhelm Institut fiir Eisenforschung, the Hermann Goring steel plant at Watenstedt, and from notes made by other investigators at other German steel plants. Preparation of Vanadium-rich Slags Most German iron ores contain only about 0.1 per cent vanadium, or even less, but some of the scandinavian iron ores available to the German iron industry in the past contain a little more than 0.1 per cent. In general German practice of vanadium recovery, nearly all of the vanadium in the ore goes into the pig iron, which is blown in the Thomas converter, yielding a slag containing about I per cent V. This slag is remelted, the vanadium again going with the iron, which is again blown in a converter, yielding a slag that averages about 10 per cent V. This slag is treated at special chemical plants, by the process of a sodadizing roast, water leach, and acid precipitation of vanadium oxide. The Herman Goring steel plant at Watenstedt used the low-grade Salzgitter iron ores, the average composition of which is shown in Table I, column I. The acid and basic iron produced in the blast furnaces contained about 0.3 per cent V. A Thomas

Jan 1, 1948

By J. D. Edwards

When Charles Martin Hall invented the electrolytic process for the production of aluminum, one basic requirement was a supply of pure alumina. Now, more than 50 years later, the same requirement still holds, and there are no technical straws in the wind to indicate that this situation is likely to change. Long ago, Aluminum Company of America took a number of steps to see that this country should not face shortages of alumina and aluminum in time of emergency. As one step to this end, the Company developed and used a supply of bauxite in South America in order to conserve dwindling Arkansas reserves. Another, and more a program than a step, was to investigate every type of process that might bear the possibility of utilizing the low-grade ores of aluminum that are more plentiful than bauxite. It is a long story, but the investigation included electric-furnace processes, acid extraction processes and alkaline extraction processes, with or without preliminary furnace and sinter treatments. Some of the processes developed were operated in commercial production. This work has been continuous since the first World War. The turn of the wheel came sooner than was expected when, in 1942, bauxite shipmerits through the caribbean became uncertain and hazardous through the operation of submarines. The tremendous requirements of aluminum for the war effort were consuming high-grade bauxite at an alarming rate and a national search for substitutes began. High-grade bauxites, for technical and economic reasons, have been defined as those containing about 7 per cent or less of silica. While bauxite of this grade was limited in amount in the United States, there was in sight a substantially greater volume of low-grade, high-silica bauxite not amenable to economic treatment by the Bayer process, but richer in alumina than the clays or other available low-grade ores. It was at this point, and after several years of intensive research on this particular phase of the problem, that Aluminum Research Laboratories brought to completion the invention of one of its research staff, which made practical the utilization of large reserves of low-grade bauxite in America. Bayer Process The Bayer process has been almost universally used for the production of alumina from bauxite. This process, in outline, comprises the digestion of hely ground bauxite in a solution of caustic soda (NaOH) under pressure and at an elevated temperature. Alumina in the bauxite goes into solution as sodium alumi-"ate and the impurities—oxides of iron, titanium and silicon—remain undissolved. The undissolved residue, known as "red mud,'' from its color, is separated and run to waste. AluKlinum hydrate (A12O3.3H2O) is precipitated from the solution of sodium aluminate, and the liquor containing the caustic soda and some alumina is returned to the Process for digesting more bauxite. The aluminum hydrate, after washing, is calcined at a high temperature to produce

Jan 1, 1949

By Frank Marotta, Louis B. Lesem, Frank Greytok, John J. McKetta

Although one of the primary variables in the calculation of the flowing bottom-hole pressure in gas wells from surface measurements is the temperature at any point and its distribution in the flow-string, only few experimental data are available in the literature and little attention has been given to analysis of the problem. Virtually all of the recently published methods of calculating flowing bottom-hole pressures depend on the assumption that either the temperature is constant at some average value or that the variation is linear with depth. The purposes of this work are to analyze the problem theoretically and to verify the analysis by comparison with experimental data so that practical problems in the analysis of the behavior of gas wells can be solved with greater accuracy, reliability, and ease. MATHEMATICAL OUTLINE OF PROBLEM Assuming that: 1. The mass velocity and chemical composition of the gas stream are constant and in normal gas well operations, the change in linear velocity in the entire flow-string is trivial, 2. The product of the density and heat capacity of the gas is constant, 3. No horizontal temperature gradient exists in the gas stream, 4. Net flow of heat by conduction within the formation and in the gas stream in the vertical direction is trivial in magnitude and can be neglected, 5. The regional vertical geothermal gradient is constant, and 6. The temperature of the gas entering the borehole is constant, and equal to that of the reservoir, a set of two simultaneous, linear partial differential equations with appropriate boundary conditions was derived to describe the temperature distribution in the gas stream and the surrounding formation. These equations were solved by operational techniques for the distribution of temperature in the gas stream. The resulting integrals were evaluated numerically on an IBM 604 at the Machine Accounting Div. of the Railroad Commission of Texas. DERIVATION OF FUNCTIONS FOR THE DISTRIBUTION OF TEMPERATURE The physical system is a circular hole of radius a in an infinite medium with thermal conductivity K, density p8, and heat capacity c,. Under shut-in conditions the well is in thermal equilibrium with the surroundings and the increment in temperature is given by - ?T3/L x. Gas of density pg and heat capacity c.. flows upwardly through this hole in the direction of increasing x with a linear velocity W. Writing a heat balance on an element of gas ?x in thickness, convective heat transfer + conductive heat transfer + energy required to lift a unit mass of fluid = change in energy content. pa2W po Co To - pa2Wpo Co To x+xx - 2apK?x ?T8/?r r=a - Wpa2 po?x/778 = CoPopa2?x?To/?t... Dividing by (copopa2?x) and taking the limit as ?x tends to zero, -W (?To/?x + 1/778Co) + 2 K/a Po Co ?T3/?r r=u = ?To/?t

Jan 1, 1958

By Taylor Cole, William T. Schneider

Drilling in West Texas during 1941 was more active than in any year since 1937, a total of 2325 wells having been drilled. Pre-Permian exploration was the greatest in the history of the area; 106 wells tested pre-Permian formations during the year. Wildcatting reached the peak since 1937, with 135 wildcats, of which 20 per cent were producers. The wells were drilled to a greater average depth than in any previous year. Slim-hole drilling was the common practice, using drilling equipment that is largely portable. Because of deeper drilling, more attention was paid to mud fluids, especially the use of materials to reduce water filtration. There has been slight improvement in the protection of the pay horizons while drilling by the use of reverse circulation, and drilling-in with oil as well as low water-filtration muds. The practice of setting and cementing the oil strings through the producing formation and perforating opposite the pay zones has increased in the fields producing from sands. It is doubtful whether this practice is of unusual value in dolomitic limestone fields. There have been few if any technological improvements in obtaining necessary information on the pay sections penetrated, by coring, core analyses, better sampling, and more detailed drilling time. However, more operators are beginning to realize the necessity of good samples. For a proper study of the reservoirs in West Texas, it is essential that better samples be obtained, that more core analyses be run, and that better methods of obtaining drilling time be initiated. It should be noted that increased drilling speeds and slim-hole drilling have tended to reduce coring and core recovery and have not aided in obtaining good subsurface samples. In fact, fast drilling speeds and slim-hole drilling have reduced the cost of drilling operations, but with the sacrifice of much needed subsurface information. Larger quantities of slower-reacting acid are being used per well. There has been improvement in shooting, in that a greater number of quarts per foot have been used and an attempt has been made to concentrate the shots opposite the pay zone. The use of mud logging to determine the characteristics of the pay section increased considerably over the year 1940. There has been a slight increase in obtaining reservoir information in the new fields, such as bottom-hole sampling, bottom-hole pressures, and records of gas, oil, and water withdrawals. However, there is great need for more data on these subjects, particularly accurate information regarding gas and water volumes. There are three repressuring projects and a fourth is nearly ready for operation in the Kermit field. There is one repressur-ing project in the Payton field and one in the North Ward field. So far, the gas-injection projects have not shown very impressive results. As yet, there are no water-flooding projects or water-disposal projects in West Texas. Not including gathering lines within the fields, 222 miles of feeder pipe lines were

Jan 1, 1942