Search Documents

By Jaakko Kajamaa

Neutron diffraction was applied to determine sheet textures by the transmission method. Cold-rolled and recrystallized copper sheets were investigated. The amount of cube texture was determined for three compositions, in which the phosphorus content was, respectively, 0, 0.005, and 0.03 wt pct. The heat treatment was in every case 8 sec at 650°C. In the two latter cases the cube texture was prevented. In addition a comparison with the X-ray diffraction transmission method was made with the 96 pct cold-rolled copper sheet. Outer parts of both (111) pole figures can be considered to be rather identical. This is seen from the fact that the intensity ratio ITD/120" was 0.45 for neutron diffraction and 0.40 for X-ray diffraction. Differences between the methods were discussed in detail. Features peculiar to neutron and X-ray diffraction in texture studies were listed and compared. In this work neutron diffraction was applied to determine sheet textures. Specifically, it was desired to ascertain whether this method can be used to reveal differences when compared to other methods. In addition, the amount of the cube texture in copper sheets was determined as a function of phosphorus content. Previous applications of neutron diffraction to texture problems include the following: nickel wires,' wire of some bcc metals,' and uranium bars.3 In the neutron diffraction technique the greatest difference is in the sample—its method of production and its volume. A sample needs no treatment and its volume is roughly 105 times larger than the volume of an X-ray diffraction sample. The cold-rolled sheet was investigated both by neutron diffraction and by X-ray diffraction, because it is expected that, due to large number of defects, possible differences in the results of the two methods would be revealed. It is a well-known fact that X-ray lines show broadening when cold-worked. Analysis has shown that this is based chiefly on small crystalline size, micro-stresses, and/or faults.4'5 Neutrons are sensitive to the above-mentioned disturbing factors as well, but circumstances in diffraction are different from the X-ray case. Because the sample represents a larger volume, the result is an average over that volume. In addition, it can be assumed that the sample has preserved its original structure, because it needs no special preparation. The particular limitation of neutrons is the relatively low neutron intensity available from nuclear reactors. This decreases the resolution as compared to the X-ray diffraction methods. Furthermore, absorption mainly reduces diffracted X-ray intensity, while multiple scattering effects, i.e., secondary extinction, disturb neutron diffraction. SO neutrons and X-rays behave in a different way when interacting with matter. As in other structural investigations, one can utilize this difference in texture studies as well. One cold-rolled and three recrystallization textures in copper sheets were investigated by neutron diffraction. The samples were produced at the Outokumpu copper factory to the specifications shown in Table I. The paper is divided into five parts. The first deals with the theory of the measurement. In the second, experimental procedures are described. Results are presented in the third part. Both cold-rolled and re-crystallized samples are studied. Discussion is in the fourth part, and finally in the fifth part some conclusions are drawn. 1) THEORETICAL CONSIDERATIONS Properties peculiar to neutron diffraction are the following: a) the scattering length varies greatly between one element and another; b) many of the elements do not absorb neutrons appreciably. In this connection it is of primary interest to know the interaction of neutrons with lattice imperfections. As with X-rays this problem leads to diffraction analysis of deformed and recrystallized metals. From the physical point of view the main difference is that neutrons are scattered by nuclei (magnetic scattering is not considered here), whereas X-rays are scattered by electrons. The features peculiar to neutron and X-ray diffraction methods in texture studies are listed in Table 11. Pole figures are an important tool in performing structural analysis of deformed or recrystallized metal. Present texture research technology requires pole figures which are as precise as possible. The choice between these two methods depends on the technical information which is required. The X-ray diffraction transmission technique may give results which are not necessarily representative of the average physical state of the sample. Although foil samples normally contain enough crystallites for diffraction, they may not necessarily represent the whole structure. An example of this problem is the frequently observed difference between the "surface" and the "inside" texture of a sample. The production of foil samples may disturb the original structure of the parent material. The selection and orientation of the foil from the sample is quite arbitrary. Normally, a highly deformed piece of metal has several texture components. Different components are deformed in a slightly different manner. This is a re-

Jan 1, 1969

By K. E. Brown, A. R. Hagedorn

Continuous, two phase flow tests have been conducted during which four liquids of widely differing viscosities were produced by means of air-lift through 1%-in. tubing in a 1,500-ft. experimental well. The purpose of these tests was to determine the effect of liquid viscosity on two-phase flowing pressure gradients. The experimental test well was equipped with two gas-lift valves and four Maihak electronic pressure transmitters as well as instruments to accurately measure the liquid production, air injection rate, temperatures, and surface pressures. The tests were conducted for liquid flow rates ranging from 30 to 1,680 BID at gas-liquid ratios from 0 to 3,-270 scf/bbl. From these data, accurate pressure-depth traverses have been constructed for a wide range of test conditions. As a result of these tests, it is concluded that viscous effects are negligible for liquid viscosities less than 12 cp, but must be taken into account when the liquid viscosity is greater than this value. A correlation based on the method proposed by Poettmann and Carpenter and extended by Fan-cher and Brown has been developed for 1¼-in. tubing, which accounts for the effects of liquid viscosity where these effects are important. INTRODUCTION Numerous attempts have been made to determine the effect of viscosity in two-phase vertical flow. Previous attempts have all utilized laboratory experimeneal models of relatively short length. One of the initial investigators of viscous effects was Uren1 with later work being done by Moore et al.2,3 and more recently by Ros.4 However, the present investigation represents the fist attempt to study the influence of liquid viscosity on the pressure gradients occurring in two-phase vertical flow through a 1¼-in., 1,500 ft vertical tube. The approach of some authors has been to assume that all vertical two-phase flow occurs in a highly turbulent manner with the result that viscous effects are negligible. This has been a logical approach since most practical oil-well flow problems have liquid flow rates and gas-liquid ratios of such magnitudes that both phases will be in turbulent flow. It has also been noted, however, that in cases where this assumption has been made, serious discrepancies occur when the resulting correlation is applied to low production wells or wells producing very viscous crudes. Both conditions suggest that perhaps viscous effects may be the cause of these discrepancies. In the first case, the increased energy losses may be due to increased slippage between the gas and liquid phases as the liquid viscosity increases. This is contrary to what one might expect from Stokes law of friction,' but the same observations were made by ROS4 who attributed this behavior to the velocity distribution in the liquid as affected by the presence of the pipe wall. In the second case, the increased energy losses may be due to increased friction within the liquid itself as a result of the higher viscosities. The problem of determining the li- quid viscosity at which viscous effects becomes significant is a difficult one. Ros4 has indicated that liquid viscosity has no noticeable effect on the pressure gradient so long as it remains less than 6 cstk. Our tests have shown that viscous effects are practically negligible for liquid viscosities less than approximately 12 cp. Actually there is no single viscosity at which these effects become important. These effects are not only a function of the viscosities of the liquids and of the gas but are also a function of the velocities of the two phases. The velocities in turn are a function of the in situ gas-liquid ratio and liquid flow rate. Furthermore, the role of fluid viscosities in either slippage or friction losses will depend on the mechanism of flow of the gas and liquid, i.e., whether the flow is annular. as a mist, or as bubbles of gas through the liquid. These mechanisms are also a function of the in situ gas-liquid ratios and the flow rates. It would thus seem that the best one could hope for is to determine a transition region wherein the viscous effects may become significant for gas-liquid ratios and liquid production rates normally encountered in the field. The viscous effects might then be neglected for liquid viscosities less than those in the transition region but would have to be taken into account when higher viscosities are encountered. There are numerous instances where crude oils of high viscosity must be produced. The purpose of this study has been to evaluate the effects of liquid viscosities on twephase vertical flow by producing four liquids of widely differing viscosities through a 1 % -in. tube by means of air-lift. The approach used in this study was as follows:

Jan 1, 1965

By G. P. Conard, R. C. Hall, J. F. Libsch

The 50 pct Fe-50 pct Co alloy undergoes a transformation from disorder to an ordered structure of the CsCl type reportedly in the vicinity of 732OC. During this process, the coercive force goes through a maximum, apparently as a result of strains associated with the coherent nucleation and growth reaction. This magnetic alloy also shows a marked increase in the ratio of residual to saturation induction, which is associated with annealing to a high degree of order with the continuous application of a magnetic field. The increase in ratio can be explained on the basis of a decrease in 90' domain boundaries and, perhaps, by an increase in anisotropy resulting from lattice distortion. THE 50 pct Fe-50 pct Co alloy undergoes a disorder-order transformation which has been reported to occur in the vicinity of 732°C1,2 The ordered structure is the CsCl type.' This magnetic alloy also shows a marked increase in the ratio of residual to saturation induction as a result of heat treatment in a magnetic field, sometimes called a response to magnetic anneal.'-' The purpose of this investigation was to study the course of the ordering reaction, the nature of the response to .heat treatment in a magnetic field, and the relation, if any, between ordering and the response. Procedure The method of approach in this investigation was to produce an initial structure as completely disordered as possible and then gradually to order the alloy by isothermal anneals at various temperatures under different conditions of the applied magnetic field. Magnetic, magnetostriction, and X-ray analyses were of primary importance in determining the property and structural changes resulting from the isothermal anneals. Rings of the 50 pct Fe-50 pct Co alloy were prepared from the elemental powders by a powder metallurgy technique, further details of which may be found in ref. 7. The initial structure was produced by annealing the specimens for ½ hr at 1000°C, cooling to and holding for ½ hr at 900°C (in the a range above the ordering temperature), and water quenching. Isothermal anneals were performed at 600°, 675°, 720°, and 740°C. For example, rings were heated to 600°C, held for a predetermined period of time, and cooled by natural cooling at a rate slightly slower than an air cool (average of 20" to 25°C per min). The tests (magnetic, etc.) were made after each heat treatment. All high temperature treatments were performed in a purified hydrogen atmosphere. The treatments at the various temperatures were carried out under one or more conditions of an applied field including 1—no field, 2—field of 20 oersteds applied on cooling only, and 3—field of 20 oersteds applied continuously during heating, holding, and cooling. Magnetic measurements were made using the standard Rowland ring technique8 with a maximum field strength of 100 oersteds. The magnetization curve, induction at 100 oersteds (B.), residual induction (Bt), and coercive force (Hc) were determined. All magnetic analysis data were based on an average of the results from three rings. A strain gage technique9 as used for the measurement of magnetostriction. The X-ray determination of the relative amount of ordered phase present was made on the ring specimen used for magnetic measurement. This was done by the back-reflection method using a rotating specimen (because of the large grain size) with unfiltered CoKa radiation and a 7 hr exposure time. Intensity measurements of the ordered line (300) were made by comparing visually the films so obtained with standard films prepared by exposing for different lengths of time a specimen given a long time anneal (high degree of order). Results In all instances the saturation induction (induction at 100 oersteds) was found to increase slightly with annealing time. This effect was small and appears to be the increase in saturation induction to be expected on ordering.10-13 The residual induction behavior was markedly influenced by the field condition during annealing, Figs. 1, 2. For the condition of no applied field, the ratio of residual to saturation induction remained essentially constant for short annealing times but showed a significant increase at longer times. With increasing annealing temperature, less time was required to produce this increase in the ratio. In the case of the 600°C anneals, the increase did not occur until approximately 20 hr, Fig. I, while on annealing at 740°C the increase was immediate, Fig. 2. Slight decreases in the ratio may be observed at 100 hr for specimens treated at 720°C and at 1 hr for those treated at 740°C. Specimens annealed in a field of 20 oersteds showed a residual to saturation induction ratio consistently higher than that for the specimens annealed without the field. The first anneal with the field (¼ hr) caused an abrupt increase in the ratio at all temperatures; thereafter, the increase in the ratio was generally similar for specimens annealed

Jan 1, 1956

By P. G. Shewmon, F. N. Rhines

THE determination of the self-diffusion coefficient of magnesium has been made possible recently by discovery1-1 of a radioactive isotope, Mg28 having a half-life of 21.3 hr,1 and subject to manufacture in useful quantity. In the present research this material was condensed from the vapor phase upon a surface of high purity magnesium. The progress of diffusion of the tracer atoms into polycrystalline magnesium was followed by machining layers and measuring the change in the intensity of radiation as a function of the distance of each layer from the surface. The self-diffusion coefficient was found to be 2.1 X 10-8 sq cm per sec at 627°C, 3.6 X 10-9 sq cm per sec at 551°C, and 4.4 X 10-10sq cm per sec at 468°C; the activation energy is about 32,000 cal per mol. Experimental Procedure Since there was no other published measurement of a diffusion velocity in any magnesium-base material, is was necessary to employ a number of new experimental techniques. The short half-life of Mg28 made it necessary to complete the entire experimental procedure within three or four days. This meant that the work had to be done where a cyclotron was readily accessible and that all operations, prior to the diffusion heat treatment, had to be so designed as to minimize their time requirements. Unusual problems were imposed also by the chemical reactivity of magnesium, its high vapor pressure, and the fact that no satisfactory method for elec-trodepositing magnesium on magnesium is presently available. Finally, the machining and handling of the easily air-borne radioactive-magnesium chips involved certain health hazards, resulting in the need for further experimental restrictions. Preparation of Mg28 The Mg28 was produced in the Carnegie Institute of Technology syncrocyclotron by the neutron spallation of chlorine.5 his involved bombarding a 2 gram crystal of high purity NaCl with a beam of 350 mev protons for a period of 2 hr, after which the crystal was dissolved in warm water and the Mg28 was concentrated and purified by chemical means (see Appendix). About 50 microcuries of Mg28 thus were obtained in the form of magnesium oxinate (8 hydroxyquin-olatc?), which was ignited in air to produce MgO. This in turn was reduced to magnesium metal vapor, by the method of Russell, Taylor, and Cooper," in the vacuum apparatus shown schematically in Fig. 1. Here the essential part is a tantalum ribbon, slightly dished to receive the MgO. The ribbon, pre- viously outgassed at high temperature, is heated to about 1700°C by passing an electric current through it, whereupon tantalum oxide is formed, magnesium vapor is released almost instantaneously, and condensed partly upon the diffusion sample. Diffusion-Sample Preparation: Hot-extruded magnesium rod, 21/32 in. round was used in making the diffusion specimens. The magnesium analyzed as follows: 0.004 pct Al, 0.027 pct Fe, 0.040 pct Mn, 0.0004 pct Cu, 0.0002 pct Ni, and less than 0.01 pct Ca, 0.0004 pct Pb, 0.0011 pct Si, 0.001 pct Sn, and 0.001 pct Zn. A brief study of the crystal texture of this material revealed a sharp fiber texture with the (001) plane roughly parallel to the extrusion axis. Cylindrical samples 1/2 in. long by 5/8 in. were machined from this rod, the end faces dressed on 3/0 emery, and lightly etched with 20 pct HC1 in water. These samples then were annealed for at least twice the intended time of diffusion, at the intended diffusion temperature, in order to stabilize the grain structure at about 1 mm average diameter. The annealing treatments were conducted in argon in the same apparatus and in the same manner as the subsequent diffusion treatments, which will be described presently. Thus, a strain-free plane surface was produced, but there remained a layer of MgO which had largely to be removed before the layer of Mg28 was deposited. Most of this layer was taken off by two light passes over 3/0 emery paper. The balance of the oxide and a thin layer of metal were then removed by etching 5 to 10 min in 4 pct nital (4 pct HNO3 and 96 pct ethyl alcohol) made with absolute alcohol. There followed immediately three quick rinses in: 1-49 1/2 pct methanol, 49 1/2 pct acetone, and 1 pct formic acid, 2-50 pct methanol and 50 pct acetone, and 3-pure benzene. This procedure is essentially that of Sturkey.7 The resulting surface, which was of almost elec-tropolished brightness, remained plane and was free of cold work. It could be kept clean by storing under benzene, or in a desiccator; short exposure

Jan 1, 1955

By R. Maddi, I. R. Kramer

The delay time for the initiation of slip was studied in single crystals of a brass, aluminum, and ß brass. A delay time for slip was found in ß brass when the specimens were tested below room temperature; however, one was not found for a brass or aluminum. A general theory for the existence of the brittle transition temperature is proposed. A LTHOUGH a considerable amount of effort has A been devoted to the study of the deformation and fracture of single crystals, the vast majority of the work was concerned with static tests or with tests carried out at relatively slow strain rates. The necessity for the study of a possible incubation time for slip becomes apparent when the various theories which have been postulated for the elucidation of the mechanism of slip are considered. The existence of an incubation period would strongly indicate that slip occurs by a process of nucleation and growth; whereas the absence of an incubation would present rather convincing evidence that slip occurs by a cataclysmic process. In addition to shedding light on the process of plastic deformation, an understanding of the early stages of plastic deformation may be helpful in finding an explanation for the brittle behavior of the body-centered metals under certain conditions. It is well known that these metals, such as iron, molybdenum, tungsten, ß brass, etc., will become brittle as the test temperature is lowered or the strain rate is increased. In spite of the fact that this subject has received considerable attention since the turn of the century, no adequate theory exists today which explains the phenomenon. In the ductile temperature range the metal breaks with a "fibrous" fracture after considerable slip has taken place. In the brittle temperature range the metal fails essentially by cleavage on the {loo) planes: however, some plastic flow is always present even in the most brittle fractures. It is possible, as will be explained later, to ascribe this brittle behavior to the length of the incubation time for slip. Clark and Wood,' using polycrystalline metals, showed that a delay time existed for the yield point in mild steels and that the delay time depended upon the applied stress. These authors stated that the delay time was observed only with those materials for which the stress-strain curve showed a definite yield point. In their work only the mild steel specimens exhibited a delay time at the yield point, while the other materials studied-type 302 stainless steel, SAE 4130 normalized steel, SAE 4130 quenched and tempered steel, 24s-T aluminum—did not show a delay time. These authors' in an extension of their work, found that as the temperature was lowered the delay time was increased. It is, then, the purpose of this investigation to measure or to set an upper limit on the delay time for plastic flow in single crystals of a brass, aluminum, and ß brass. The delay time will also be studied as a function of temperature. The incubation time may be measured by determining the length of time the specimen will support a stress without slip occurring when the stress is greater than the static critical resolved shear stress. In order to accomplish these measurements use was made of a pendulum which was so designed that a single crystal specimen could be placed at various positions along its length. When a pendulum is struck by another pendulum of the same length, an elastic wave is transmitted down the bar with the velocity of sound in the material and is reflected from the far end of the bar. The reflected wave then travels back and unloads the stress until it reaches the impacted end of the bar and the two pendulums separate. The length of time that the specimen is subjected to the stress is equal to the time it takes for the stress wave to travel twice the distance from the specimen to the end of the bar. The stress applied to the specimen is governed by the velocity of impact of the two pendulums. The stress at which the specimen first suffers plastic: deformation was determined in these experiments by examining the specimen under the microscope for the first appearance of slip lines and by measuring the residual strain after each impact. In these experiments the critical resolved shear stress was approached from the low stress side and no attempt was made to determine it exactly. To determine it exactly, it would have been necessary to find that stress at which slip would have just started. However, since the stresses were increased in rather small increments the critical stress is believed to be approached rather closely, as will be seen from the experimental results. The critical stress will be taken as the highest stress obtained before the onset of plastic deformation. The stresses

Jan 1, 1953

By M. R. Annis, P. H. Monaghan

The control of mud properties affords two practical means of tnitigating pipe sticking caused by differential pressure: (I) teducing weight and, therefore, differential pressure; and (2) reducing the friction berween the pipe and mud cake. This paper describes investigation of the second of these—the friction between the pipe and the mud cake. Friction between a steel plate and a mud cake, held in contact by a differential pressure, was measured in the laboratory while maintaining a constant area of contact. Experiments were performed to determine how this friction varied with changes in mud composition and with changes in experimental conditions such as the differential pressure, time of contact of plate and mud cake, and filter-cake thickness. It was found that the apparent coefficient of friction, or the "sticking" coeficient, was not a constant; instead, it increased with increased time of contact between plate and mud cake, and with increased barite content of the Mud. The sticking coeficient varied from about 0.05 to 0.2 afer 20 , and eventually reached values of 0.1 to 0.3 after two Hours. Quehracho or ferrochrome lignosulfonate reduced the sticking coefficient at short .set times but did not reduce the maximum value. Carboxy-~t~etlz~lcellulose had no effect on the sticking coeficient. Emulsification of oil in the mud reduced the sticking coefficient. Some oils reduced the sticking coefficient to about one-third of its Value in the oil- free base mud, while other oils reduced it only slightly. Addition of certain surfactants with the oils further reduced the sticking coefficient. Spotting a clean fluid over the stuck plate caused a reduction in sticking coefficient only if the differential presslrrr was reduced, either temporarily or- permanently. INTRODUCTION Often during drilling operations the drill string becomes stuck and cannot be raised, lowered, or rotated. This condition can be brought about by a number of causes, such as sloughing of the hole wall, settling of large particles carried by the mud, accumulation of mud filter cake during long stoppage of circulation and, finally, sticking by pressure of the mud column holding the pipe against the filter cake on the hole wall. This paper is concerned with the last-mentioned phenomenon. Helmick 2nd Longley' in 1957 suggested that a pressure differential from the wellbore to a permeable formation covered with mud cake could hold the drill pipe against the borehole wall with great force. This situation occurs when a portion of the drill string rests against the wall of the borehole, imbedding itself in the filter cake. The area of the drill pipe in contact with filter cake is then sealed from the full hydrostatic pressure of the mud column. The pressure difference between the mud-column pressure and the formation pressure acts on the area of drill pipe in contact with the filter cake to hold the drill pipe against the wall of the borehole. Helmick and Longley also presented laboratory cxperiments which showed that the force required to move steel across a mud cake increased with increasing differential pressure and with the time the stcel and mud cake had been In cuntact. Their data indicated that replacing the bulk mud with oil reduced the force required for movement. Field evidence was rcported that spotting oil over the stuck interval sometimes freed the pipe. Outmans- in 1958 presented a theoretical paper which described the sticking mechanism and explained the increase of sticking force with time with equations derived from consolidation theory. Since publication of these papers, there has been interest in the differential pressure sticking of drill strings, and several mud additives to reduce sticking or special equipment to free stuck pipe have been proposed."" Haden and Welch" have recently reported laboratory evidence showing that the composition of the filter cake influences the force necessary to move steel on the filter cake. There seems no doubt that differential pressure sticking is a real phenomenon and that its severity depends on the magnitude of the pressure differential across the mud cake, the area of contact and the friction between pipe and mud cake. The mud weight required to control a well is determined by the highest formation pressure in the well: hence, the magnitude of the differential pressure opposite normal or subnormal pressure formations cannot bc reduced. The area of contact may be minimized in several ways (control of filter-cake thickness, use of stabilizers and spirally grooved drill collars), but there arc practical limitations which prevent reduction of contact area from becoming a complete solution of the problem. However. the mud composition might bc altered to reduce the friction between pipe and mud cake. This paper presents quantitative measurements of the friction between steel and mud filter cake and shows how the friction varies with mud composition for given experimental conditions.

By Tell Ertl

TODAY'S mining industry is witnessing a transition in labor utilization. The drill-jumbo operator, the mucking-machine operator, the blasting crew, the scaling and timbering crew are all specialists. The all-around miner is rapidly disappearing. As mechanization has resulted in a higher order of underground skills; specialization of labor has been a natural consequence, as has the need for more supervision and engineering. Mines now are cleaner, neater, safer, and have a greater productivity per man-shift than ever before. Nothing spectacular like the continuous miner has yet come to the underground metal mines, but t a gradual improvement in methods, equipment, and technical knowledge is achieving the increased efficiency. With the exhaustion of the rich ores and large profits and who-cares-about-the-costs, mining has become a business; that of producing low value ores at costs below selling price. Charles A. Chase, patriarch of Colorado mountain mining men, manager of the Shenandoah-Dives, was one of the first to preach and prove his preachings that mining is a business. He has been mining a lead-copper-zinc-gold-silver ore, much from elevations above 1.3,000 ft, for a quarter century without a shutdown.-The ore is of such low value that most engineers and investors still would consider it foolhardy. Yet he has kept Silverton, Colo., alive, has paid wages without a lapse, has produced $25 million of new wealth and maintained a steady return to the investors. This type of responsibility is increasingly apparent in the mining business and is one feather that can be worn proudly. .Much emphasis is being placed on improving, the productive mining operations-breaking, loading and transportation. Breaking in underground metal mining is done by drilling and blasting. To the writer's knowledge, no chain or rotary-type machine has been developed for mining strong, abrasive rock. Drilling Percussion drills are still the standard drilling machines underground. Diamond drills, that: were the rage a decade ago for drilling long holes, are being superseded by the rock drill. The development of the hard abrasion-resistant carbide bit permits full-gage long holes to be drilled by percussion drills at a lower cost than diamonds. The change in the use of percussion drills is chiefly in the method of mounting. The column and arm are disappearing and the jackleg and rubber-tired or track-layer jumbo mountings are taking its place. At the Homestake mine .lightweight jackhammers mounted• on pneumatic legs using 7/8-in. hexagonal drill. rods and 1 1/2-in, tungsten-carbide detachable bits have been found more portable and maneuverable. They have less air consumption, lowered, dynamite consumption, and more footage and tonnage per man-shift than with 3 1/2-in. drifters on a column mounting. Drills now are mounted on longer feed carriages, drilling up to 20 ft without changing steel. These mountings result in great savings because the driller can set up quickly, drill the entire depth of the hole without changing the drill rod or bit using carbide and one-use bits, and can move his machine quickly to the next hole. One man to the machine is becoming general practice. The result is longer rounds rounds drilled at a lower cost than the previously used short rounds. A jumbo developed in the Tri-State can be extended to mine ore left in the roof up to 65 ft above the floor. Drill-rod life was formerly considered to be about 250 min of actual use. The increase in the drilling time per rod per day has gone up considerably with the development of the jumbo and the long-feed carriage, resulting in which is apparently more rod breakage., Consequently, a great deal of research is being done in the attempt to develop an alloy-steel rod with longer service life to offset the greater cost. Some reports indicate that alloy steel or Swedish steel results in cheaper drilling than conventional drill rod. However, several tests have shown only slightly increased life for alloy drill rod. Undoubtedly, the blow of the rock drill, the length of the drill rod, and the resiliency of the rock being drilled are important factors in the life of drill rod, so it follows that alloy steel might work well in some mines and result in no savings in others. The bit forged on the drill rod is seldom encountered and steel detachable bits are not as common as in the recent past. The one-use bit is gaining popularity because of. the difficulty in rehardening reconditioned steel bits satisfactorily. It is thought that the, carbie-insert bit is most applicable to drilling hard 'rock' where the steel bit is unable to drill out a full change, for instance, in extremely abrasive

Jan 1, 1952

By R. E. Smallman, I. Milne

The deformation behavior of single crystals of Nb-Mo alloys has been investigated with particular reference to the influence of composition, orientation, and temperature. Strong solid-solution hardening was observed reaching a maximum at the equiatomic cotrlposition and can be attributed to the difference in atomic size between niobium and molybdenutrz. Changes in the form of stress-strain curve, as shown by a high work-hardening rate and restricted elongation to fracture, were observed at a composition of Nb-85 pct Mo and are attributed to the presence of MozC DreciDitate. Conjugate slip was only extensive in dilute alloy samples; at the 50/50 composition deformation rnainly occurred by primary slip, and the onset of conjugate slip gave rise to failure by cleavage on (100). The variation of yield stress of Nb-50 pet Mo with orientation was consistent with slip on (011)(111) slip systems. The temperature deperndence of the yield stress between -196" and 250°C was similar to that of pure bcc metals, but at a much higher stress level; no evidence for twinning %as found. IN recent years the deformation behavior of various pure metals in groups VA and VIA has received considerable attention, but surprisingly little work has been carried out on binary alloys made by mixing metals from the two groups. Such an investigation would be of interest since single crystals of metals of group VA have been shown to deform characteristically with a multistage deformation curve1"3 while a parabolic type of deformation curve has been reported for most of the group VIA metals.4'5 It has been suggested by Law ley and Gaigher~ that the difficulty encountered in obtaining multistage deformation curves for molybdenum in group VIA was possibly because of the presence of a microprecipitate of MozC which they observed even at carbon contents as low as 11 ppm. Recently a multistage deformation curve has been reported for molybdenum ," although the stages are not so definitive as those for group VA metals. The binary alloys of the particular refractory metals which have been investigated in single-crystal form include Ta-w,' Ta- Mo,' and Nb- Na." While a large amount of hardening was observed for alloys of the Ta-W and Ta-Mo systems, associated with room-temperature brittleness for alloys approaching the equiatomic composition, Ta-Nb remained ductile over the complete composition range with little or no solution hardening. Other systems have been investigated by hardness measurements on polycrystalline material and a discussion of the hardening of these alloys has been presented by ~udman." The purpose of the present investigation was to examine the deformation behavior of Nb-Mo alloys in detail, with particular reference to alloy composition and single-crystal orientation. In this way it was hoped to shed some light upon the restricted ductility of these alloy specimens. 1) EXPERIMENTAL PROCEDURE The starting materials were obtained in the form of beam-melted niobium rod and sintered molybdenum rod of suitable dimensions. Since niobium and molybdenum form a complete solid-solution series at all temperatures, alloy single crystals were produced by melting the two constituents together in an electron bombardment furnace (EBM). To produce specimens free from segregation a molten zone was passed over the length of each rod six times in alternate directions at a speed of 10 in. per hr. Typical specimens were analyzed for interstitial impurities by gas analysis and for metallic impurities by spectrographic analysis. The results of this analysis are shown in Table I. Many of the tensile specimens were also analyzed (after testing) by scanning the gage length in an electron beam microanalyzer, from which it was found possible to predict the approximate composition of a specimen from the original proportions of each element in the EBM. The tensile specimens were made with a gage length of 0.5 in. and diameter of 0.075 in., using a Servomet Spark machine. By careful machining on the finest range for the final i hr of this technique, surface cracks could be reduced to the level where they were easily removed by electropolishing in a solution of nitric and hydrofluoric acids. The specimens were strained at a rate of 10 4 sec-' using friction grips designed to prevent accidental straining and maintain a good alignment before straining. The orientations of the individual specimens tested are shown in Fig. 1 and the corresponding compositions listed in Table I1 together with collated experimental data. 2)RESULTS a) General Deformation Behavior. The effect of composition on the room-temperature deformation curves of similarly oriented specimens is shown in Fig. 2. The yield stresses of the pure constituents, while not the lowest reported to date, were at least comparable with existing data. Although the solution hardening was large for alloys at either end of the phase diagram, and comparable with the Ta-W solution-hardening data of Ferris et a1.,8 the low work-hardening rate characteristic of niobium was sustained until a composition of Nb-85 pct MO had been reached. Associated with the peak yield stress ob-

Jan 1, 1969

By M. C. Fuerstenau, D. W. Fuerstenau

Studies of the collection of alkali and ammonium halides utilizing vacuum flotation techniques and contact angle measurements show that ionic size controls the flotation of techniquesthese halides with amine salts measurementsas collector. Contact angles of air bubbles on sylvite in saturated brines were withaminemeasured salts asascollector.a function of such variables as collector addition, length of collector chain, and pH of the brine. No contact occurs between halite and an air bubble in brines containing dodecylammonium acetate as collector. LONG-CHAINED aliphatic amine salts have been used for the separation of sylvite (KCl) from halite (NaCl) by flotation.1,2 It is puzzling how these two minerals, which are so similar chemically and crystallographically, can be separated by this method. Gaudin" has postulated that the difference in floatability of halite and sylvite with salts of primary amines depends on ionic size: In the case of amine flotation, the cation would attach itself to the chloride. I have a speculation there, which I cannot prove, that the ammonium group, that is the —NH3 group in the amine, floats potassium chloride because the dimensions of this grour, as it has been measured in other compounds is almost identically the dimensions of the potassium ion, quite different from the sodium ion, and so it fits where potassium had been, in place of it and not attached to it. Apparently, because an aminium ion (RNH3+) is much larger than a sodium ion, it cannot fit into the lattice of halite. Taggart also has speculated that ionic size may control the floatability of sylvite.4 The object of this experimental investigation has been to test this hypothesis and to study what controls the adsorption of cationic collectors at the surface of sylvite. Since collection is to be approached from the viewpoint of ionic size, the ionic radii that are of interest in this work are presented in Table I. The values of the ionic radii of the ions listed in Table I, except NH4+, are those given by Pauling." Several different values for the radius of the ammonium ion have been given, but that of Goldschmidt6 seems to be preferred. The radius of the charged head of a dodecylammonium ion is assumed to be the same as that for the ammonium ion. Little experimental work has been reported in the technical literature concerning the separation of sylvite from halite by flotation. Guyer and Perren studied the separation by flotation of 50 pct binary mixtures of NaCl, KC1, NH,Cl, NaNO3, KNO3, K2SO4, and Na,SO, using either oleic acid or a sodium sul-fonate as collector.' It is possible to measure floatability under actual flotation conditions where all three phases, air- water-mineral, are present by vacuum flotation tests and contact angle measurements.9 Both of these techniques were used in the experimental approach in this paper. Experimental Method and Materials The vacuum flotation tests were run with glass-stoppered pyrex graduated cylinders. Twenty-five ml graduates were used to test the floatability of all salts studied except rubidium and cesium salts. For each test distilled water containing the desired collector concentration was saturated with the salt to be floated. Sufficient salt (—48 mesh) was added to leave about 2 ml of solids in the bottom of the graduate. After the graduate had been agitated several minutes to saturate the solution with air, a vacuum was applied. If the salt were floatable in the collector solution, the gas bubbles attached themselves to the particles, and the particles floated to the surface. In determining the floatability of the expensive Rb and Cs halides, the experiments were run in 10 ml graduates with about 11/2 ml of collector solution initially. Contact angles were measured in the usual manner except that the solutions had to be previously saturated with the mineral to avoid dissolution of the crystal. Solutions for studying contact angles were made by adding the desired amount of collector to a saturated brine, giving the collector concentration in molarity. The mixture was agitated until dissolution of the collector was complete, with the exception of those concentrations greater than about millimolar. At these high concentrations complete dissolution of the collector was impossible. The face of the mineral to be tested was a freshly cleaved crystal of halite or sylvite. The mineral was placed in the brine and conditioned with collector for at least 15 min, which was found to be long enough to obtain a maximum value for the contact angle. The temperature remained constant during each experiment. The experiments were run at 24°C ±2°C. For contact angle measurements, a crystal of halite from Carlsbad, N. M., was used. Several samples of sylvite were used in this work: a crystal of sylvite from Stassfurt, Germany; a crystal from Carlsbad, N. M.; and a crystal of chemically pure potassium chloride. Saturated brines were made from reagent grade chemicals and distilled water.

Jan 1, 1957

By R. Maddin, C. H. Mathewson, W. R. Hibbard

Recent publicationsl.2 establishing the presence of cross-slip in strained metallic single crystals oriented wholly within the area of single slip as predicted from the generalizations of Taylor and Elam3 described these markings as they appeared during the initial stages of the deformation process. At that time, the plane having a common glide direction with the primary slipping plane was reported as the cross-slip plane although the specific direction was not confirmed. Consequently, in continuation of the research, it seemed advisable to investigate the micro-graphic appearance of cross-slip together with the Laue back-reflection X ray analysis and stress-strain data during the later stages of the deformation process. Accordingly, a single crystal of brass (72.75 pct Cu, 0.01 pct Fe, 0.01 pct Pb, 27.23 pct Zn) was polished mechanically and repolished electrolytically after the manner described in the earlier paper.' Three pairs of flat surfaces, parallel to the specimen axis, and (1) perpendicular to the plane containing the pole of the primary glide plane and the specimen axis, (2) perpendicular to the plane containing the pole of the cross-slip plane and the specimen axis, and (3) perpendicular to the plane containing the slip direction and the specimen axis, were polished mechanically and repolished electrolytically, resulting in a final minimum gauge diameter of 0.4864 in. in a gauge length of 3.36 in. The specimen was elongated in tension and load-extension readings were taken following the method described in the initial investigation.' Observed reorientations were obtained from a series of Laue back-reflection photograms at the center and ends of the gauge length and at various positions around the circumference of the specimen. These were interpreted after the manner of A. B. Greninger.4 Cross-slip (Fig 1 and 2) was found with the first appearance of the primary slip clusters and usually joined members of these clusters. In addition, a third set of entirely different markings (Fig 3) could be noted. The displacement of this third set by the primary slip lines was measured as 8300 at. diam (3.04 microns). Since the specimen was carefully observed at high magnifications before any deformation and no markings of any type could be noted, it would appear that this third set was formed during the deformation process prior to the initiation of classical primary slip. Additional extensions produced no unusual change in the appearance of either cross-slip or the third set of markings. The number of lines increased with increasing elongation and appeared, generally, in areas where earlier markings were present. The continuity of the clusters of cross-slip lines in Fig 4, 5 and 6 illustrates that they are neither noticeably displaced by nor do they displace the primary lines at this stage. In Fig 7, cross-slip appears in a long narrow localized band approximately 45 degrees from the stress axis. This somewhat resembles a twin band except for the lack of a sharp boundary. After a shear of 0.257, suffcient additional glide occurred on the cross-slip plane to displace the primary slip lines (Fig 8). Generally, where a large number of cross-slip lines could be observed in an area on one flat surface, few cross-slip lines appeared on the diametrically opposite position on the parallel flat (Fig 9). These, of course, were not matched observations on the same glide ellipses. It was extremely difficult to make such comparisons. The third set of markings (Fig 10) was extensively displaced by glide on the primary slip planes. A plot of the width of primary slip clusters versus their displacement of the third set of lines is shown in Fig 11. The slope and the linearity of the plot suggest that each primary glide plane slips to a constant maximum value of shear before further slip is transferred to another plane. A shear value of 0.28 was determined in this case. Heidenreich5 has presented a similar schematic representation of glide for aluminum. After the specimen had attained an elongation of 51.8 pct, corresponding to a shear of 0.973, cross-slip appeared very prominently in certain areas as shown in Fig 12, yet at diametrically opposite positions very little cross-slip could be noted, Fig 13. Classical conjugate slip was found at this advanced stage in the deformation, Fig 14, which corresponds to the axial location shown at 12 in Fig 15. It should be noted that cross-slip occurs within the conjugate slip clusters and on the same plane as the cross-slip associated with the closely spaced primary lines which constitute a background in less distinct focus. The third set of markings noted at all stages in the deformation of the

Jan 1, 1950

By H. Conrad, V. Damiano, J. Hanafee, N. Inoue

The effects of hydrostatic pressure up to 400 ksi at 25" to 300°C on the mechanical properties of three forms of commercial beryllium (hot-pressed block, extruded rod and cross-rolled sheet) were investigated. Three effects of pressure were studied: mechanical beharior under pressure, the effect of pressure-cycling, and the effect of tensile prestraining under hydrostatic pressure on the subsequent tensile properties at atmospheric pressure. For all three materials the ductility increased with pressure whereas the flow stress did not appear to be significantly influenced by pressure. An increase in the subsequent atmospheric pressure yield strength generally occurred as a result of pressure-cycling or prestraining under pressure, whereas either no change or a decrease in ductility occurred. The only exception to this was sheet material, which exhibited some improvement in ductility following a pressure-cycle treatment of 304 ksi pressure. The effects of pressure-cycling and prestraining were relatively independent of the temperature at which they were conducted. Stabilized cracks of the (0001) type were found in hot-pressed specimens and {1120) type in extruded and sheet specimens following straining under pressure. Also, pyramidal slip with a vector out of the basal plane, presumably c + a, was identified by electron transmission microscopy for extruded rod and for sheet strained under pressure. Small loops similar to those previously reported were found after straining at pressures of the order of 300 ksi. THE use of beryllium in structures is limited because of its poor ductility under certain conditions. Therefore, one objective of the present research was to determine if the ductility of beryllium at atmospheric pressure could be improved by prior pressure-cycling or prestraining under hydrostatic pressure. Another objective was to study the mechanisms associated with the plastic flow and fracture of the polycrystalline form of this metal with pressure as an additional variable. Since the early work of Bridgman,1 it has been recognized that many materials which are brittle at atmospheric pressure exhibit appreciable ductility when strained under high hydrostatic pressure. This effect has been reported for beryllium by Stack and Bob-rowsky2 and by Carpentier et al.3 and has been attributed to the operation of pyramidal slip systems with slip vectors inclined to the basal plane while cleavage or fracture is suppressed.4 That such slip may occur simply by the application of pressure alone without external straining (pressure-cycling) is suggested by the results on polycrystalline zinc5 and polycrystalline beryllium,6 where nonbasal dislocations with a vector (1123) were reported. A significant improvement in the ductility of the bee metal chromium by pressure-cycling has been reported.7 On the other hand, limited studies on the pressure-cycling of the hcp metals zinc67819 and beryllium6 indicated no improvement in ductility; there only occurred an increase in the yield and ultimate strengths. The study on beryllium was limited to hot-pressed material. Consequently, additional studies on the effects of pressure-cycling on other forms of beryllium seemed desirable, especially since for chromium some authors10 have been unable to detect any improvement in ductility while others find a large improvement.7 That the ductility of polycrystalline beryllium at atmospheric pressure might be improved by prior straining under hydrostatic pressure was suggested by the known beneficial effects of cold work on the ductile-to-brittle transition temperature in the bee metals. It was reasoned that, by straining under hydrostatic pressure, fracture would be suppressed, and during the propagation of slip from one grain to its neighbor dislocations with a vector inclined to the basal plane"-'4 would operate. Upon subsequent straining at atmospheric pressure, these dislocations with a nonbasal vector would continue to operate and thereby reduce the tendency for fracture to occur, by assisting in the propagation of slip across grain boundaries and by interacting with any cracks that may develop. It was recognized that maximum improvement in ductility would probably occur at some optimum amount of prestrain under hydrostatic pressure. If the pre-strain was too small, an insufficient number of dislocations with a nonbasal vector would be activated; if it was too large, internal stresses (work hardening) might increase the flow stress more than the fracture stress, or incipient cracks or other damage could develop. EXPERIMENTAL PROCEDURE 1) Materials and Specimen Preparation. The materials employed in this investigation consisted of hot-pressed block (General Astrometals, CR grade), extruded rod (General Astrometals, GB-2 grade with a reduction ratio of 8:1), and cross-rolled sheet (Brush S200, 0.065 in. thick). The analyses of these materials and mechanical properties at room temperature and atmospheric pressure are given in Table I. The grain size of the hot-pressed block was 15 to 16 µ, that of the extruded rod 10 to 11 µ, and that of the sheet 7 to 10 µ in the rolling plane and 5 to 6 µ in the thickness, all determined by the linear intercept method. Al-

Jan 1, 1969

By R. P. Abendroth

The hydrogen-water vapor ratio at which Fe-Cr alloy, chromium oxide, andiron chromite coexist in equilibrium was determined between 900" and 1200°C. A thermogravimetric method was used to determine equilibrium conditions. The results fit a straight-line relationship in the temperature region studied, and are given by Reduction experiments were also performed to confirm the results of the equilibrium investigation. ThE oxygen pressures at which Fe-Cr alloy, chromium oxide, and iron chromite coexist in equilibrium have been previously determined by Boericke and angert,' Morozov and Novokharski,' and Katsura and uan. Only one determination (at 1300°C) was made by Katsura and Muan, but it agrees with the results of orozov and Novokharski. The results of Boericke and Bangert, however, differ appreciably from the results of these investigators. Previous studies have assumed that the equilibrium metallic phase is pure iron, but Dahl and Van vlack have shown that the iron contains from about 1 wt pct Cr at 1000°C to over 2 wt pct above 1300°C. The chromium oxide also contains a small amount of iron in solid solution. In the present study, hydrogen-water vapor mixtures were equilibrated with the condensed phases, using a therrnogravimetric method to determine equilibrium conditions. The reaction can be written EXPERIMENTAL General Procedure. The starting material was a sintered pellet of Fe2O3-Cr2O3 solid solution with a hole in the center, and was placed on a fused silica hook. This assembly was raised into the preheated hot zone of the furnace in a helium atmosphere, hooked onto a fused silica hangdown suspended from one arm of an Ainsworth Model RV-AU-1 recording balance, and the starting weight determined. A flowing hydrogen-water vapor atmosphere was then exchanged for the helium by evacuation, and the sample reduced until the weight loss indicated the sample composition to be in the alloy-Cr2O3-chromite field. The tem- perature was adjusted incrementally until constant sample weight was achieved for several hours, to within 0.02 mg. A hydrogen-water vapor atmosphere of different composition was then admitted, and the same procedure carried out. At the end of a series of determinations, the sample was examined by X-ray diffraction to verify the presence of the desired phases. Microscopic examination of the silica hook showed no interaction with the sample, nor did it lose any weight. Several criteria were used to insure equilibrium besides constancy of weight. For a given hydrogen-water vapor composition, equilibrium was approached from both oxidizing and reducing sides by varying the furnace temperature slightly. The resulting slow weight loss or gain was observed for several hours. Constant weight could be re-established by returning to the original furnace temperature. The last criterion used was varying the relative amounts of the phases by further reduction or oxidation, and observing any changes in temperature required for constant weight for a given hydrogen-water vapor atmosphere. None were observed. This procedure was essentially the same as approaching the equilibrium from oxidizing and reducing sides, but larger weight excursions were carried out. Sample Preparation. Reagent-grade Fe2O3 and Cr83 powders were mixed in the desired proportions and heated in air at 1250°C for 2 hr. The mixture was re-ground and heated in air overnight at 1250°C. X-ray diffraction showed complete solid-solution formation as a result of this procedure. The solid solution was then pressed into l/2-in.-diam pellets using Carbowax 4000 as a binder. The hole was drilled in the center, and the pellets were sintered 24 hr at 1250°C in air on a bed of Fe2O3-Cr2O3 of the same composition, contained in an alundum boat. After cooling, the pellet surfaces were abraded with 310 paper to remove any surface compositional differences, such as loss of Cr2O3. Chemical analysis of the sintered pellets was 67.16 wt pct CrP3 and 33.02 wt pct Fe203. Atmosphere Generation and Control. The hydrogen-water vapor atmospheres were generated by passing Matheson ultrahigh-purity hydrogen, with no further purification, through two water bubblers contained in a constant-temperature water bath. Since the water-vapor dew points required in this study were below room temperature, the bath was insulated, and was cooled by thermoelectric-immersion devices. The bath temperature was controlled to 0.0l0C. Since rather high flow rates of about 900 ml per min were used through the furnace tube, an independent check of the dew point was made to insure saturation of the hydrogen by the water vapor. Although the dew point could only be determined to within 1/2"C, the determined dew points agreed with the water-bath temper-

Jan 1, 1967

By J. J. Tietien, R. O. Clough

A technique previously used to prepare alloys of InAs1-xPx and GaAsl-x Px, miry: the gaseous hydrides arsine and phosphine, has been extended to grow single -crystalline GaAs 1-x Sb x by replacing the phos-phine with stibine. Procedures were developed for handling and storing stibine which now make this chemical useful for vapor phase growth. This represents the first time that this series of alloys has been grown from the vapor phase. Layers of P -type GaSb and GaSb-rich alloys have been grown with the carrier concentrations comparable to the lowest ever reported. In addition, a p-type alloy containing 4 pct GaSb exhibited a mobility of 400 sq cm per v-sec which is equivalent to the highest reported for GaAs. RECENTLY, interest has been shown in the preparation and properties of GaAs1-xSbx alloys, since it was predicted1 that for compositions in the range of 0.1 < x < 0.5, they might provide improved Gunn devices. However, preparation of these alloys presents fundamental difficulties. In the case of liquid phase growth, the large concentration difference between the liquidus and solidus in the phase diagram, at any given temperature, introduces constitutional supercooling problems. It is likely that, for this reason, virtually no description of the preparation of GaAs1-xSbx by this technique has been reported. In the case of vapor phase growth, problems are presented by the low vapor pressure of antimony, and the low melting point of GaSb and many of these alloys. In previous attempts1 at the vapor phase growth of these materials, using antimony pentachloride as the source of antimony vapor, alloy compositions were limited to those containing less than about 2 pct GaSb. This was in part due to the difficulty of avoiding condensation of antimony on introducing it to the growth zone. A growth technique has recently been described2 for the preparation of III-V compounds in which the hydrides of arsenic and phosphorous (AsH3 and pH3) are used as the source of the group V element. With this method, GaAs1-xPx and InAs1-xPx have been prepared2&apos;3 across both alloy series with very good electrical properties. Since the use of stibine (SbH3) affords the potential for effective introduction of antimony to the growth apparatus, in analogy with the other group V hydrides, this growth method has been explored for the preparation of GaAs1-xSbx alloys. In addition to GaSb, these alloys have now been prepared with values of x as high as 0.8. In the case of GaSb, undoped p-type layers were grown with carrier concentrations equivalent to the lowest reported in the literature. Thus it has been demonstrated that, with this growth technique, all of the alloys in this series can be prepared. EXPERIMENTAL PROCEDURE A) Growth Technique. The growth apparatus, shown schematically in Fig. 1, and procedure are virtually identical to that described2 for the growth of GaAs1-xPx alloys, with the exception that phosphine is replaced by stibine.* HCl is introduced over the gallium boat to *Purchased from Matheson Co., E. Rutherford,N+J. transport the gallium predominantly via its subchlo-ride to the reaction zone, where it reacts with arsenic and antimony on the substrate surface to form an alloy layer. The fundamental limiting factors to the growth of GaAs1-xSbx alloys from the vapor phase, especially GaSb-rich alloys, are the low melting point of GaSb (712°C) and the low vapor pressure of antimony at this temperature (<l mm). Thus, relatively low antimony pressures must be employed, which, however, imply low growth rates. To provide low antimony pressures, very dilute concentrations of arsine and stibine in a hydrogen carrier gas were used. Typical flow rates (referred to stp) were about 4 cm3 per min of HC1 (0.06 mole pct)+ from 0.1 to 1 cm3 per min of ASH, (0.002 to 0.02 mole pct), and from 1 to 10 cn13 per min of SbH3 (0.02 to 0.2 mole pct), with a total hydrogen carrier gas flow rate of about 6000 cm3 per min. Although no precise data on decomposition. kinetics exist, it is known4 that stibine decomposes extremely rapidly at elevated temperatures. However, the high linear velocities attendent with the high total flow rate (about 2000 cm per sec) delays cracking of the stibine until it reaches the reaction zone and prevents condensation of antimony in the system. To improve the growth rates of the GaSb-rich alloys, growth temperatures just below the alloy solidus are main-

Jan 1, 1970

By W. L. Mamme, G. Y. Chin

The problem of selection of the active slip systems for a crystal undergoing an arbitrary strain was analyzed by Taylor and by Bishop and Hill in terms of a minimum (internal) and a maximum (external) work criterion, respectively. These two criteria have now been generalized to include crystallographic slip on several sets of slip systems, twinning mixed with slip, and slip by (noncrystallographic) pencil glide. The generalized treatment also takes into account the possibility of a Bauschinger effect and of unequal hardening among the shear systems, which were considered in the Bishop and Hill work. Optimization techniques of linear and nonlinear programming are shown to be applicable for the numerical calculation of the minimum or maximum work. In the case of crystallographic shear, the constraint functions are linear and hence the optimal work is obtained as the saddle value of the lagrangian function Wi(y) e minimum and W,(u) + (a) for the maximum, where Wi is the (internal) work, We is the (external) work, Y is the crystallographic shear strain, u is the applied stress, and and are constraints. It is shown that the Lagrangians are functionally the same and the saddle value of one problem is identical to the saddle value of the other, proving that the two analyses are completely equivalent. In the case of pencil glide, although the constraint functions are nonlinear and neither convex nor concave, the equivalence of the optimal values to the saddle value of the Lagrangian (which is again identical for both problems) is still valid. WHEN a crystal deforms plastically by crystallographic shear, five independent shears are generally required to accommodate five independent strain components specifying the deformation. Assuming slip as the only shear mechanism, Taylor1 in 1938 analyzed the deformation in terms of a minimum work criterion. He hypothesized that of all combinations of five slip systems which are capable of accommodating the deformation, the active combination is that one for which the internal work C is a minimum, where 1 TI is the critical resolved shear stress for slip on the 1-th slip system and is the corresponding simple shear. By further assuming equal 72 for all equivalent slip systems and no Bauschinger effect, Taylor re- duced the minimum work problem to one of minimum and applied the analysis to the case of axisym- Metric flow by {111}(110) slip in fcc crystals. However, he did not consider the question of whether the resolved shear stress has in fact attained the critical value for slip on the newly found active systems without exceeding it on the inactive systems. In 1951 Bishop and ill&apos; put forth the maximum work analysis in which slip is again assumed as the only deformation mechanism. In this analysis, the work o1 done in a given strain ij by a stress ujj not violating the yield condition is maximized. In addition, the analysis takes into account the possibility that the critical resolved shear stress for slip may not be equal among the slip systems and that the slip behavior may exhibit the Bauschinger effect. As with Taylor, a single set of slip systems—{111)(110) — was analyzed numerically. It thus appears that the Bishop and Hill treatment is on a more sound physical basis than the Taylor treatment. However, Bishop and Hill showed that where there is equal hardening among all slip systems and when there is no Bauschinger effect, Eq. [11 ] of Ref. 2, as assumed by Taylor, the results of their maximum work analysis are the same as those of Taylor&apos;s minimum work analysis. Hence at least under those conditions there is an implication that the Taylor analysis does lead to a critical resolved shear stress for slip on the predicted active systems without violating the yield condition on the inactive systems. Recently, the Taylor analysis was applied for numerical solutions of the axisymmetric flow problem, for slip on {110}(111), {112}(111). {123)(111) systems as well as a mixture of all three sets of svstems."1 Computational techniques based on the optimization theories of linear and nonlinear programming4 were employed in these solutions. The same techniques were employed in the solutions of an axisymmetric flow problem of deformation by slip on (111) (110) systems and twinning on (111)(112) systems5 which had been considered theoretically from a modified Taylor approach. The utilization of these techniques has led to the realization that the solutions of Taylor&apos;s minimum work problem imply the solutions of Bishop and Hill&apos;s maximum work problem. The two problems turn out to be dual problems in the well known sense of mathematical programming. It is thus the purpose of this paper to first generalize the minimum and maximum work analyses to include crystallographic slip on several sets of slip systems, twinning mixed with slip, and slip by (non-crystallographic) pencil glide, as well as the possibility of a Bauschinger effect and of unequal hardening

Jan 1, 1970

By E. S. Bumps, M. Baeyert, W. F. Craig

SOME time ago during a study of impact properties of tempered martensite,1 it was postulated that the consistently good ductility of tempered martensite might be caused by its relatively small and peculiarly shaped ferrite grains. The fer-rite grains of tempered martensite have approximately the same size and shape as the martensite "needles." Thus they form an interlocking mass of needle-shaped grains quite different from equiaxed or lamellar ferrite grain structures. When the common mechanical test methods are applied to steel, variations are often observed in the ductility of specimens that have closely similar hardness and tensile strength values. The ductility so measured appears to be structure dependent. When steel from the same heat has been heat treated to produce different structures with the same hardness, the elongation and reduction of area values from the tensile test and the transition temperature determined by the notched-bar impact test vary according to whether pearlite, tempered martensite, or other structural constituents were produced by the heat treatment. It has been widely recognized that tempered martensite gives a consistently good performance, when tempered to the same hardness as many other structures with which it has been compared. In recent years the isothermal transformation of austenite to specific structural products and the quantitative evaluation of the character of these products with respect to their nature and response to deformation has received considerable attention. The objective of the present study was to pursue somewhat further the dependence of ductility upon structure; specifically, it was desired to ascertain whether ferrite grain structure, including both shape and size of the grains, can account for the consistently good performance of tempered martensite in the notched-bar impact test. It was thought that a simple experiment would indicate whether the ferrite grain structure plays any part in the good ductility exhibited by tempered martensite in contrast to other steel structures with different types of ferrite grains. By determining the impact transition temperature, it was proposed to compare spheroidites having similar carbide particle size and spacing but obtained in such a manner that their ferrite grain structures would be very different. Spheroidite obtained by tempering martensite, with its small, needle-shaped grains, was to be compared with spheroidite from pearlite. If the latter is produced by sub-critical annealing, the ferrite grains correspond to the pearlite colonies. Thus, if the pearlite was not too coarse, the ferrite grains of spheroidite from pearlite are equiaxed in contrast to the needle-shaped grains of spheroidite from martensite. It was thought that the ferrite grain structure of spheroidite from martensite might depend to some extent upon the grain size of the prior austenite. The austenite grain boundaries limit the maximum attainable size of the martensite needles and thus of the ferrite grains in the derived spheroidite. In order to evaluate any possible influence of prior austehite grain size, spheroidites were to be prepared from martensites that had been formed from fine-grain austenite and also from coarsened austenite. As the carbide particle size and distribution were to be essentially alike in the various spheroidites, the difference would be in the ferrite grain size and shape. Thus any marked difference in transition temperature could be attributable to the character of the ferrite grain structure. There are certain considerations in assuming that these spheroidites would be equivalent in all respects except ferrite grain structure, and an attempt was made to take them into account. One of the considerations was the choice of the carbon content of the steel. An approximately eutectoid steel was selected for two reasons. First, the pearlitic structure would contain no proeutectoid ferrite which might complicate the picture by producing a non-uniform ferrite grain structure in the resulting spheroidite. Then, too, the high-carbon content would inhibit ferrite grain growth during the sub-critical treatment. Another factor to be taken into account was the choice of an alloying element to assure a martensitic structure throughout on quenching the impact specimens. Nickel was chosen, because it is a common alloying element and resides in the ferrite both upon its formation from austenite and throughout tempering. The formation of alloy carbides, or even a large solubility of the alloying element in cementite, would have complicated the interpretation by changing the composition of the ferrite .during spheroid-ization. The possibility of temper brittleness was minimized insofar as possible by using a tempering temperature as high as consistent with the 1 pct of nickel in the steel, namely, 1150°F. While it certainly is not claimed that no difference other than ferrite grain structure could exist between the spheroidites, nevertheless, reasonable precaution has been exercised within the limits of steel metallurgy. It is believed that any large difference in transition temperatures would reflect the difference in ferrite grain structure and that relatively good ductility in the spheroidites from mar-

Jan 1, 1951

By J. Weijdema, D. N. Dietz

In the conventional underground combustion process (dry combustion) much heat is left behind in the swept formation and goes to rva.rte. Econonmy can be improved by heat recuperation through water injection. This is most advantageous if done at the earliest opportunity before much heat is dissiputed to cap and base rock. Water injected simultaneously with the air will flash to superheated steam, which passes through the combustion front together with the nitrogen from the air. A condensation front traveling up to three times as fast as the combustion front drives out the oil. In this type of wet combustion, the water evaporates before it reaches the combustion zone. The evaporation front travels more slowly than the combustion zone. If so much water is injected that the evaporation front overrun the combustion front, combustion in that spot will be quenched and some unburned fuel will be left behind. Air reacts with the oil farther down-stream where steam temperatures occur; at steam temperature, the air reacts rapidly with the oil. Velocity of the combustion front is increased thereby and is governed essentially by the water-injection rate. In the extreme case of high water-injection rate, a short heat wave of constant length is driven through the formation by water injection. Once this wave has been established, no more heat need be generated than that required to make up the heat losses from the short heat wave; a relatively low rate of air injection will suffice. The feasibility of partially quenched combustion has been confirmed in tube experiments. A heat wave at steam temperature is observed. Chemical analyses of flue gas indicate preferential burning of hydrogen while a carbonaceous residue is left in the formation. Introduction A disadvantage of so-called dry in situ combustion is that air-compression costs are rather high. An air consumption of about 400 std cu m/cu m (400 scf/cu ft) of formation swept is an accepted figure. This high consumption is mostly wasted since much heat is left behind in the depleted oil sand. Methods were investigated for recuperating as much as possible of the heat left behind. This paper deals only with basic principles and is confined mainly to one-dimen- sional flow without lateral heat losses; experiments were conducted in relatively narrow, well insulated tubes. If some water is injected with the air, it will turn to superheated steam in an evaporation front, which should travel behind the combustion front. The steam having passed the combustion front causes a steam drive by a condensation front that can travel faster than the combustion front. The latter needs to travel only part of the distance covered by the oil-displacing condensation front, and thus consumes less air. The water-air ratio would seem limited to that at which cold water overruns the combustion. This limitation was deliberately exceeded considerably in theory and experiments. It was found that combustion is then indeed quenched, but only locally. Farther downstream, the oxygen finds residual oil at steam temperature, which is suficiently high to ensure rapid oxidation. Thus, the combustion front uses only part of the available fuel because it is chased through the formation faster than its normal velocity. No heat is left behind. This new process is called "partially quenched combustion". At the upper limit of the water-air ratio, a small heat slug is moved through the formation by the flow of water and steam. Only a small flow of air is needed since it has only to generate sufficient heat to make up for the lateral heat losses of the short heat slug. Theory Although many factors complicate underground combustion, the processes will be presented in their simplest form. For this reason, one-dimensional flow without lateral heat losses is assumed. Heat conduction in the direction of flow also is disregarded. Under these conditions, dry combustion causes very high temperatures. The heat-carrying capacity of the gas stream is small. Heat generated by oxidation of a residual oil saturation is retained in the sand. The available fuel determines the air requirement and the temperature obtained. Accepting the often-mentioned air consumption of 400 std cu m/cu m (400 scf/cu ft) formation, we calculate a temperature of the swept sand of 1,200C (2,192F) (Fig, I). If water is injected at a modest rate with the air, it will flash to superheated steam upon contact with the heated sand. One cu m (35.31 cu ft) of hot formation will evaporate about 0.5 cu m (17.66 cu ft) of water, and thereafter will accommodate (at an estimated 0.80 saturation and an assumed 0.40 porosity) another 0.3 cu m (10.59 cu ft) of water in cold condition. As long as less than 0.5 + 0.3 = 0.8 cu m (28.25 cu ft) of water is injected for every 400 std cu m (14,125 scf) of air (water-

Jan 1, 1969

By O. A. E. Jackson

Pebble milling has been practiced in the reduction works of South Africa gold mines for well over 50 years. Originally flint pebbles were imported from Denmark to grind stamp-mill amalgamation-process tailing, which contained a good deal of extractable gold, but local operators soon found that large pieces of ore could be used for the same purpose. The ore is a hard, tough conglomerate in which quartz pebbles are cemented together by a matrix of redeposited silica interspersed with pyrite crystals. The gold, rarely visible, occurs as fine particles mostly segregated at the interface of the pebble and matrix, although a small fraction occurs within the pyrite crystals. There is seldom any gold in the pebbles themselves. Following the usual South African practice in pebble milling, Union Corp. grinds the ore wet in two or three milling stages incorporating classification. The sized broken ore used as grinding media is separated from the main ore stream in the crushing section that prepares the ore for milling. Where the ore channel, or reef, is narrow there is a shortage of large pebbles. In this case primary grinding may be done in ball mills or, more recently, in rod mills, which cost less per ton to operate. The trend, however, is to prepare finer feed for the milling section. This makes it possible to use smaller primary pebbles and eliminates the need for steel. REDUCTION WORKS OF UNION CORP. LTD. Union Corp. Ltd. exercises financial and technical control over a group of seven gold mines in the Transvaal and Orange Free State. In the Transvaal, with one exception. the mines lie 20 to 40 miles east of Johannesburg, in flat or gently rolling countryside. Winkelhaak, the first of several new mines that will be developed by Union Corp., is located in similar terrain in an entirely new gold mining district about 80 miles east of Johannesburg. Table I gives details of milling units for six of the Union Corp. mines, together with the tonnage milled in 1957. Winkelhaak Mines Ltd. is not included, as it did not begin milling until 1958. This reduction plant has no crushing section; ore is ground directly from the mine (autogenously) in 12x16-ft mills. Because these operations are still in development, they are not described in this article. It will be noted that certain reduction works have mills of more than one size in the same milling stage. This came about when plant extensions in- corporated larger units. In the case of Geduld Propty. Mines Ltd., which began milling operations 50 years ago, the primary stage is stamp milling. The reduction works follow a uniform pattern and are usually joined to the main ore shaft. Ore from other shafts is brought by standard-gage railway and dumped into a common transfer bin. The trend is to increase surface storage capacity to enable the crushing and milling sections to operate at a steady rate, independent of fluctuating ore deliveries from mine. Milling and cyanide extraction divisions of new mines are always designed to allow for extensions as mine production increases. The conveying, washing, and screening system of the crushing section is usually laid out in final form, with additional space for more crushing equipment. The crushing sections operate on one shift during early years of mine production; a second shift is introduced when the mining rate warrants it. Ample surge capacity is provided. Crushing and milling is done only on weekdays, as the law does not allow these operations to take place on Sunday in any plants constructed since 1911. The cyanide extraction sections, however, operate continuously seven days a week, drawing on mill pulp gradually built up in the thickeners during the week. Construction and equipment of milling plants follow standard practice. Dilution water is drawn from a large, high-level tank to obtain constant pressure, but gland service water for the pulp pumps is reticulated from high-pressure, two-stage pumps. The mills are equipped with the most up-to-date machinery and are designed to save labor. They compare favorably with milling plants in countries where native labor does not exist, and automatic controls are being installed wherever feasible. Hydrocyclone classifiers have replaced mechanical classifiers in modern milling plants, chiefly because of the saving in capital outlay, maintenance, and building space. The hydroclones are fed from steady head boxes rather than directly from pumps, and dilution water is introduced into these boxes. Tests have shown that in steadiness of operation and separating efficiency cyclones are comparable to mechanical classifiers. but protective stationarv screens are needed to keep the spigots clear. Rubber-lined pumps are used for pulp of about 3 mesh or finer and metal-lined pumps for coarser material. None of the Union Corp. milling plants practices gravity concentration of coarse gold by amalgamation or the use of corduroy blankets. Studies have proved that no economic case can be made for these methods, which complicate the milling process and demand extra precautions against theft.

Jan 1, 1960

By W. V. Green

Creep of tantalum was measured at temperatures from 0.6 to 0.89 of the absolute melting temperature. The creep curves include first, second, and third stages. Steady-state creep rate depends on the fourth power of stress. The activation energy for creep throughout this temperature range is approximately 114 kcal per mole, measured by the aT technique. Subgrain formation occurs as a result of creep strain, and pile-up dislocation arrays are observed in etch-pit patterns. BECAUSE of its high melting point-which is exceeded only by those of rhenium and tungsten—and its high room-temperature ductility compared to most of the other high-melting-point metals, tantalum will undoubtedly be utilized in an increasing number of high-temperature applications. Alloying studies directed toward increased high-temperature strength must use data on tantalum itself as a base line in order to evaluate the effectiveness of the alloying additions. However, to date, no systematic study of creep of tantalum at temperatures above one-half of its melting point has been reported in the literature. Conway, Salyards, McCullough, and Flagella1 have measured linear creep rate of tantalum sheet as a function of stress, but at only one temperature, 2600°C. This paper describes a relatively thorough study of the high-temperature creep of tantalum. METHOD Material Tested. The commercially supplied, l/2-innch-diameter tantalum rod used for this work was electron-beam-melted, cold-forged, rolled, swaged, cleaned chemically, and vacuum-annealed for 1 hr at 1000°C, all by its manufacturer. The vendor&apos;s analysis included 60 to 170 ppm C, 3.4 to 4.2 ppm H, 60 to 80 ppm 0, 15 ppm N, and a hardness ranging from 66 to 81 Bhn and averaging 76 Bhn. Creep eimens Used. Two creep-tested specimens are shown in Fig. 1. The 1/4 in.-diameter gage section was 3/4 to 1 in. long, and terminated either at shoulders 5 mils high or at 20-mil-diameter tantalum wires spot-welded to the circumference of the gage section. Both kinds of shoulders served equally well as fiducial marks for optical strain measurements. The spot welding did not alter the creep behavior in any detectable way; the 5-mil- high sharp shoulders did not result in any detectable localized effect on the strain. Before testing, each tensile bar was first mechanically polished -id then electrochemically polished according to the method referred to by Forgeng2 as the "Thompson Ramo Woolridge" method, which was suitable for tantalum after small adjustments of technique were made. Two tensile bars tested at low stresses had 1/8-in.-diameter gage sections and utilized only the weight of the bottom grip for the applied load. Although these diameters were smaller than were desired for other reasons, applied loads were known with high precision in the tests in which they were used. Testing Procedure. Two different constant-load creep-testing machines were employed, one of which has been described by Smith, Olson, and Brown.3 In both, the tensile bar is held vertically on the axis of a cylindrical tungsten tube or screen heater by threaded tungsten grips. The tensile bars and associated grips are heated by radiation from the incandescent heaters, which are heated by their own electrical resistance. Both testing machines use pins to hold the bottom grips in place. The load is applied to a tensile bar through hanging weights, a constant force-multiplication lever, a pull rod sealed to the chamber lid, and a top grip threaded to the pull rod at one end and to the tensile bar at the other. In one machine, the vacuum seal is a bellows with a low spring constant; in the other, the seal involves a rotating "0 ring". With the latter, rotation is converted to translation with a crank shaft, so that elongation of the tensile bar is accommodated with no change of tensile load. The incandescent tensile bar is viewed by an external optical system through slots in the radiation shields and heater, and an enlarged image is projected on a ground-glass screen. Gage-length measurements are made on this image with cathetometers on traveling microscopes. With regard to creep-test results, the two machines were identical. Thorium oxide coatings were applied to the threaded ends of the tensile bars, to prevent diffusion welding of the tensile bars to the grips during testing. Specimen temperatures were measured with an L. & N. optical pyrometer which had been calibrated against a standard carbon arc, and were corrected fir window absorption by calculation from the measured spectral transmittance of the quartz observation windows. Longitudinal temperature gradients in the tensile-bar gage length and temperature drifts during testing were detectable but small, and were estimated to be 10°C or less. Accuracy of temperature measurement was confirmed by comparing the temperature measured on the surface of a special

Jan 1, 1965

By Arnulf Muan, Klaus Schwerdtfeger

Equilibrium ratios C02/C0 of a gas phase coexisting with selected phase assemblages of the system Fe-Mn-0 have been determined in the temperature range 1000" to 1300°C. The oxygen pressure for the "hfnO" +hfn30, equilibrium and for the "(Fe,hTn)O" + (Fe,Mnh 0* equilibrium at high manganese contents has been determined by electromotive force measurements using stabilized zirconia as a solid electrolyte. The notstoichometry 01&apos; "hTnO" and of "(Fe, iM1z)O" solid solutions has been determined by ther-mog-/avi?netry and by wet-chemical analysis. The data obtained are used to derive activity-composition relations in "(Fe,hfn)O" and (Fe,Mn),O4 solid solutions. WUSTITE "FeO" and manganosite "MnO" form a continuous series of solid solution at high temperatures,&apos; and so do magnetite Fe304 and the high-temperature, cubic modification of Mn304 (Ref. 2) (high hausmannite, -1170). The oxides "FeO" and "MnO" are cation-deficient phases.495 The nonstoi-chiometry of "(Fe,Mn)O" solid solutions has been studied by Engell and ~ohl&apos; at two selected C02/C0 ratios at 1250°C. The two oxide end members of the spinel solid solution, FesO4 and Mn,04, however, are known to be close to stoichiometric under the experimental conditions used in the present investigation.&apos;&apos;&apos; The oxygen pressures of "(Fe,Mn)07&apos; solid solutions in equilibrium with iron have been determined by Schenck and coworkers,8 by Foster and welch," and by ~n~e1l.l&apos; The two former groups equilibrated the condensed phases in C02-CO atmospheres of lmown compositions, whereas Engell" used a galvanic cell with stabilized zirconia as a solid electrolyte. The results of these investigators are not in good agreement. Activities of FeO in manganowiistite as calculated from the results of Foster and Welch show ideal behavior, those of Engell yield a pronounced positive deviation, and those of Schenck et 01. show a moderate positive deviation from ideality. In the present work oxygen pressures for the iron + manganowiistite and manganowustite + spinel equilibria and the nonstoichiometry of manganowiistites have been measured. The data were used to calculate activities in the manganowiistite and spinel solid solutions. EXPERIMENTAL METHODS The COz/CO ratios at which manganowustite and iron are in equilibrium were determined by thermo-gravimetric and quenching methods. Experimental details are described in a previous publication.&apos;2 In the thermogravimetric technique, incipient reduction of manganowiistite pellets to metallic iron was observed as a break in the weight vs log COZ/CO curve. In the quenching technique, manganowiistite samples were partially reduced to metallic iron, or the metallic iron of manganowustite + metallic iron mixtures was partially oxidized to manganowustite, in atmospheres of constant C02/CO ratios. After quenching the composition of the oxide phase was determined by X-ray lattice parameter measurements and comparison with a standard curve obtained from oxide solid solutions of known compositions. The nonstoichiometry of "MnO" and "(Fe,Mn)07&apos; solid solutions was determined by chemical analysis of samples equilibrated in C02-CO atmospheres and quenched to room temperature, as well as thermo-gravimetrically by reducing (Fe,Mn),04 or Mn304 to manganowiistite or manganosite. The equilibrium between manganowiistite and (Fe,Mn),04 was measured thermogravimetrically by reducing (Fe,Mn),04 solid solutions having composition in the range of %„ l(NFe +NM) from 0 to 0.63. No experiments could be performed with this technique at higher manganese contents, because the equilibrium C02/C0 ratios are too large for accurate control. An additional difficulty arises at the higher manganese contents due to the strong increase in oxygen content of the manganowustite phase with increasing log Py near the manganowiistite-spinel boundary. Consequently a sharp break in the weight loss vs log C02/CO curve cannot be observed at the phase boundary. At high manganese contents of the manganowiistite, e.g., (NMn/(NF~ + NMn) > 0.9, electromotive force measurements with stabilized zirconia as a solid electrolyte were made to determine the equilibrium oxygen partial pressure. Experimental details are described in a previous paper.* Mixtures of "(Fe,Mn)O" and (Fe,Mn),04 were pressed to pellets, and the oxygen pressure of the equilibrated samples was compared to that of Ni + NiO mixtures in the cell The composition of the manganowiistite in the equilibrated two-phase mixture was determined by lattice parameter measurements and comparison with known standards. The oxygen pressure for the Ni + NiO equilibrium was taken from available data.l3~l4 No reliable results were obtained with the electromotive force technique on iron-rich oxides. The electromotive force drifted strongly with time in this composition range. An additional difficulty arises from the partial de-

Jan 1, 1968

By M. E. Fine, A. A. Henderson

Investigation of the tensile properties of silver based aluminum alloy crystals was undertaken because it appeared attractive for studying strengthening effects due to Suzuki locking with minimum complication. Yield drops were observed in all alloy crystals (1, 2. 3. 4, and 6 at. pct Al) after strain aging at room temperature. No yield drops were found in similarly grown and tested silver crystals. The yield effects are attributed to Suzuki locking but the major portion of the solid solution strengthening to other mechanisms. INVESTIGATION of the tensile properties of single crystds of silver alloyed with aluminum was undertaken because it appeared to be a system in which segregation at stacking faults associated with partial dislocations1 would be the dominant factor in anchoring dislocations. First, silver and aluminum have closely similar atomic sizes and thus solute atom locking of a dislocation due to elastic interactions should be unimportant. Second, while both X-ray2 and thermodynamic3 investigations show short-range ordering in silver-based aluminum alloys, the degree of local order is quite small (X-ray measurements give v = EAB - 1/2(EAA + EBB) = - 0.025 ev and thermodynamic measurements give v r -0.007 ev) and should not be important in strengthening dilute alloys. Third, the stacking fault energy of silver is probably low (as indicated by the profusity of annealing twins) and is very likely diminished further and quite rapidly by aluminum additions since the A1-Ag phase diagram shows a stable hexagonal phase at only 25 at. pct Al. Also, a careful investigation in this laboratory4 has shown that the ratio of twin to normal grain boundaries in recrystallized alloys increases with aluminum content. Thus, with minimum complication from other factors, Ag-A1 alloys seem attractive for studying strengthening effects due to segregation at stacking faults of extended dislocations. EXPERIMENTAL METHOD Single crystals measuring 250 by 5 by 1.5 mm of pure Ag (99.99 pct) and Ag-A1 alloys (A1 of 99.999 pct purity) of nominal compositions* 1, 2, 3, 4, and 6 at. pct were grown in high-purity graphite molds from the melt under a dynamic vacuum (1 x l0-5 mm Hg). The technique consisted of moving a furnace having a hot zone (which melted about 0.5 cm of alloy) over a horizontal, evacuated quartz tube con- taining the mold and alloy at a rate of 3/8 in. per hr. Chemical analysis showed roughly the first inch of the crystal to be solute poor, the last inch solute rich; and the center section uniform in composition within the sensitivity of the analytical method (± 0.2 at. pct Al). The center section of the crystal was cut into five specimens. Gage lengths of reduced cross section, measuring from 1.5 to 2 cm in length, were mechanically introduced by means of jeweler&apos;s files and fine abrasive cloth with the crystal firmly held in polished steel guides. One-third of the cross section was then removed by etching and electro-polishing, the crystals were all subsequently annealed for several days at 850°C in a dynamic vacuum (<1 x 10-5 mm Hg) and furnace cooled to 200°C. The crystal orientations were determined using the usual back-reflection Laue technique. The Laue spots were sharp and of the same size as the incident beam. However, microscopic examination showed the crystals to contain substructures with subgrains of the order of a micron in diameter. The details of this substructure are presently under investigation. Tensile testing was done with a table model Instron using a cross-head speed of 0.002 in. per min. For testing at various temperatures the following media were used: 1) 415oK, hot ethylene glycol; 2) 296ºK, air, acetone, water; 3) 273ºK, ice water; 4) 258ºK, ethylene glycol "ice" in ethylene glycol; 5) 200°K, dry ice in acetone; 6) 77ºK, liquid nitrogen. EXPERIMENTAL RESULTS A) Yield Behavior—A portion of an interrupted stress-strain curve for a 6 at. pct A1 crystal of the indicated orientation tested at room temperature is shown in Fig. 1. Initially, at (a), there is a small, gradual yield drop of about 10 mg per sq mm2. However, on stopping the test, and aging for a few minutes at (b), a sharp yield drop is found. Aging for longer times at (c) and (dl results in larger yield drops (and larger AT&apos;S). At, defined in Fig. 1, is usually larger than the yield drop by about 20 pct; however, this increase in the lower yield is transient since extrapolations of the flow stress curves join as may be seen from Fig. 1. (Both Laue and low-angle scattering photographs revealed no evidence of precipitation in a strain-aged 6 at. pct A1 crystal.)

Jan 1, 1962