Search Documents

By Emil Gathmann

Discussion of the paper of EMIL GATHMANN, presented at the San Francisco meeting September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1485 to 1492 H. W. LASH, Cleveland, 0.-I have found in practical experience that it is not objectionable to have some blow-holes in ingots. They enlarge during solidification and have a tendency to cause the steel to rise. If they are of fairly small size they weld up quite readily, especially where they are some distance from the surface. In that way a pipe, which is much more detrimental than a few small blow-holes, is prevented. There is a very great difference in the formation of blow-holes in steel. You get one condition in soft steel and entirely another condition in rail carbon, or the still higher grades. The figures that are given in Mr. Gathmann's paper I imagine are taken from the higher carbons, as it is very seldom that piping occurs in soft steel. J. W. RICHARDS, South Bethlehem,, Pa.-This contribution is very welcome, and I understand that the process of Mr. Gathmann is in practical use and has proven successful. I believe the experience of steel makers is that an ingot which has a pipe is of more solid structure, and therefore takes a great deal more work in the rolls and in mechanical treatment, than an ingot which has some blow-holes. The density of the piped steel is undoubtedly increased. My opinion is that it is un-

Jan 12, 1915

By H. M. Fisher, R. E. Snow, S. C. Sun

RAPID colorimetric estimation of the amount of transparent minerals has been applied successfully to instream mill products at the cryolite flotation plant of the Pennsylvania Salt Mfg. Co., Na-trona, Pa. Apparatus used was a Bausch & Lomb monochromatic colorimeter. The optical assembly of the colorimeter, shown in Fig. 1, passes light from a 6-v, 32-cp, prefocus incandescent lamp through two condensing lenses, a heat-absorbing filter, an aperture-control diaphragm, an interference filter, and a sample container. The light finally strikes a barrier-layer photocell and the output current of the photocell is measured by a galvanometer. The engraved index line of the collective lens, located between the lamp and the galvanometer, is imaged upon the transmission scale of the colorimeter by the galvanometer mirror. Reflected light from the galvanometer mirror, the position of which is determined by the output current of the photocell, enables reading of percent transmission throughout the mineral sample being tested. The colorimeter, Fig. 1, was standardized as follows: 1—The colorimeter was' connected to a Sola constant voltage transformer, A, of 6-v output operated from a 110-v ac supply. 2—Turning the toggle switch, C, illuminated the transmission scale, B, and the control knob, D, was adjusted with a blank in the optical system until the hairline on the scale read zero. 3—A No. 430 interference filter, E, was inserted into the filter channel, F. 4—A test tube, G, containing 7 cc of distilled water was pressed into the sample space, H, and the fine adjustment knob,

Jan 1, 1955

I TOLD you above that you should save the melted material that you extracted by smelting the ore. In substance this is copper, lead, silver, and perhaps gold, but all are like substances mixed in one body without any distinction. Now if you wish to separate these and to reduce them to their pure qualities, it is necessary to proceed with each one according to its own methods. Now in this method of separating lead in order to extract the silver and gold from the copper, it is necessary to return to the smelting and to follow one of two methods.* The first is to smelt it again with the addition of lead or lead ore, and to make it all run through the channel into the large forehearth that was made in front of the blast furnace, and, as it cools off, proceed to remove layer by layer with the fork, as I told you before and as you did the first time, until the work lead is reached. Then you assay what you have extracted and see whether it contains silver. If you consider that it has enough per hundred to justify the expense, return it again to the smelting. Continue to do this until you have extracted all the unctuousness and the work lead still remains. If it contains little or no silver, you must be satisfied with your work; otherwise return it again to smelt, always accompanying it with lead or galena and do as you did the other times until it

Jan 1, 1942

By C. E. Shoenfelt

The deepening of the General Crude Oil Company's No. 1 Meyers, NE. NE. SE. of sec. 22, 24S., 36E., in the Cooper area of Lea County, in April, 1934, resulted in the discovery of an oil field of major importance. The discovery well is an old well drilled by Cranfill $ Reynolds and completed in July, 1929, in limestone at 3438 ft. for an initial production of 90,000,000 cu. ft. (estimated) of 'gas. Deepening operations were started early in April, 1934, and cores were taken from the old total depth of 3438 to 3508 ft. A Haliburton test taken through the drill stem at 3439 to 3460 ft. showed 50,000,000 cu. ft. of gas with an increase of 5,000,000 cu. ft. between 3461 and 3474 ft. When completed the well tested 12,000,000 cu. ft. of gas and 5000 bbl. of oil at 3474-3508 feet. The new oil field—the result of this discovery—is between the Eunice and the Jal fields, closer to the productive area of Jal than to that of Eunice but far enough away from both to be considered a separate area. Eventually, all of these pools may be joined together by productive oil wells to form a single unit of large size. They lie in a general northwest-southeast alignment and the intervening areas have not been condemned by dry holes. In the drilling campaign that followed this discovery, 24 wells were drilled, of which 23 were oil wells with combined initial productions of

Jan 1, 1935

In their presentations Dr. Puddington and Dr. Stratton-Crawley have concentrated on spherical agglomeration and two-liquid extraction respectively. I should like here to complete the picture by putting these two techniques together in context with other techniques in which non-polar oils are used in the concentration and separation of minerals. Although these techniques are invariably treated separately and have been studied in isolation, there is a lot to be said for considering them together and trying to systematize their similarities and differences. This I take as a principle guideline in my introduction to this discussion. Four processes can be distinguished on the basis of the dosage of oil required: --simple flotation with collector-extender --agglomeration (emulsion) flotation --spherical agglomeration --two-liquid separation Dr. Stratton-Crawley has suggested that "pigment flushing" could find application in the treatment of ores. This is an interesting suggestion. However, the process can be regarded as a variant of two-liquid extraction, and it is convenient for me to do so in this discussion. Table 1 sets out some main features of these techniques. The first, in which the oil is used to enhance the strength and reduce the dosage of the collector is not designed for and has no special advantages in the treatment of fines, and therefore will not be further treated here. To add to the details appearing in the Table, thumbnail sketches of the other three, which all do show particular efficacy in the treatment of fine particles, are given below.

Jan 1, 1979

By H. O. Hofman

THE leading antimony mineral is stibnite. In smelting stibnite ore two processes are available, precipitation and roasting-reduction. The former is suited only for high-grade ores. As low-grade ores are more common than high-grade, roasting-reduction is of greater importance than precipitation. In the roasting process the aim may be to leave the oxidized antimony in the ore, or it may be to volatilize as much of the antimony as possible, collect the volatilized oxide as a rich intermediary product and smelt it for antimony, leaving the gangue poor enough to be considered a waste product. Whichever way the roast is conducted certain difficulties inherent in stibnite are encountered. These are: 1. The low melting point of stibnite which; according to Pelabon,1 is 550°C., according to Wagemann2 540°C., and according to Borgström3 546°C. 2. The ignition temperature: According to Friedrich,4 stibnite, if heated in air, begins to oxidize at 290°C. if the size of a grain is 0.1 mm. in diameter; at 343°, if 0.1 to 0.2 mm.; and 430° if 0.2 mm. 3. The fusibility of a mixture of Sb2S3 and Sb203 which in the form of kermesite (Sb2S3)2.Sb203 melts at 517°C.5 4. The volatility of Sb2S3 and Sb203, for which no numerical data appear to exist, although practical experience has shown that they are volatile at low temperatures.

Jan 1, 1916

By Franklin Moeller

Discussion of the paper of FRANKLIN MOELLER, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 343 to 354. K. A. PAULY, Schenectady, N. Y.-I read with interest Mr. Moeller's paper descriptive of the mechanical parts of the new electric hoist at the Granite Shaft of the North Butte Mining Co. and as the paper treats largely of the mechanical equipment I have little discussion to offer. There is, however, one question which I would like to ask and that is, why the discrepancy in hoisting cycles between the curves given in the paper read by Mr. Sykes for the American Institue of Electrical Engineers at San Francisco and those given in the paper under discussion? In Mr. Sykes' curves the acceleration period is shown to be 16 sec. for all depths from 2,000 to 4,000 ft. inclusive, while Mr. Moeller in Fig. 2 shows 25 sec. throughout the range and in Fig. 4 shows 35 sec. Mr. Moeller's curves also show the following reductions in the peak load during acceleration: Level, Feet Mr. Sykes, Horsepower Mr. Moeller, Horsepower 2,060 3,500 3,130 3,000 3,800 3,480 Fig. 2 4,000 4,100 3,800 2,250 1,595 Fig. 4 As the purchaser's specifications called for 15 or 16 sec. I would like to know whether or not any modifications have been made in the requirements since the equipment has been installed.

Jan 5, 1916

GEO. F. COMSTOCK,* Niagara Falls, N. Y. (written discussion?).-In this exposition of experimental data, the author infers, indirectly at least, that by the Charpy test information was obtained that led to the improve-ment of certain ordnance parts and that this improvement could not have been attained without the Charpy test. On examination of the data, however, it appears that the important point of the whole matter was that while the material had been accepted from the results of longitudinal tensile tests, it was really transverse ductility that was desired. The writer has no desire to attempt to detract from the value of the paper or to discredit the Charpy test in any way, but he would like to ask the author if he will not give more clearly his reasons for preferring the Charpy impact test for investigational and control work of this kind, over the more usual tensile test made in a transverse direction. The tensile test pieces are more cheaply made than the square notched impact bars; and from the former the limit of elasticity and the ultimate strength as well as, the ductility are obtained, while in the Charpy test only one property is measured. It does not seem that the author has shown a sufficient reason for favoring the latter test, when both it and the trans-verse tensile test served his purpose equally well in indicating the proper metal and treatment required for his special forging, and it is hoped that this reason will be given more clearly as a matter of useful general information.

Jan 11, 1919

By W. T. Burns

Attempts were made in 1908, at the Great Falls Works, to produce ingots direct from the Butte precipitate by smelting the material in a reverberatory refining furnace. The ingots produced in this manner averaged 99.4 per cent. of copper and 0.40 per cent. of arsenic and antimony. The copper content being considered too low, it was decided to cast the copper into anodes and to treat the anodes in the electrolytic plant. No. 1 Furnace, in which the precipitate was treated, was a regular cathode refining furnace previously employed in making wire bar, cake, and ingot from electrolytic cathodes. The hearth of the furnace was 24 by 12 ft., having a capacity of 100,000 lb. of cathodes. The furnace was coal fired, and the copper was dipped by means of trolley ladles. The average composition of the furnace charges was as follows: Per Cent. Peer Cent. Copper. Precipitate,..........7.5.3 40 to 80 Purification cathodes,.....1.9 92 Refinery slag (oxide slag),.. 10.1 50 to 60 Electrolytic cathodes,... 2.1 99.9 Precipitate anode scrap,.... 3.1 99.0 Scrap copper,.........7.5 99.2 100.0 The slag from this furnace amounted to 46 per cent. of the total amount charged and was of the following average composition: Per Cent. Cu..............16.86 SiO2.............34.7 FeO.............18.8 A12O3.............13.0 CaO.............9.4 MgO.............2.7 S............... 0.47 As..............0.11 Sb...............0.006 Ag, oz per ton.....0.18

Jan 1, 1914

By R. V. Whetsel, V. R. Garfias

THE present study is intended as a preliminary statistical survey of the world's production of petroleum substitutes. The information presented is admittedly deficient. It is believed, however, that the increasing importance of these substitutes, particularly with Europe at war, justifies its presentation at this time, if for no other [ ] reason than to encourage enlightened pertinent discussion. The world's production in 1939 of petroleum substitutes-of which approximately 97 per cent are direct substitutes for motor fuels-is tentatively estimated at 108,000,000 bbl., or equivalent to the combined output of crude oil in 1939 of Rumania, Mexico and Colombia. With few exceptions, these figures of production represent also actual figures of consumption. The United States, owing mainly to its output of natural gasoline, leads all countries in the production of these products, with about 53 per cent of the total. In European countries, particularly Germany, the imminence of war in 1939 forced an increase in production and improvement of methods of manufacturing motor fuels, largely from coal, with the result that this country produced in that year over 20,000,000 bbl. of substitutes. Since the beginning of hostilities, substitutes have offered more and more the means of meeting the unfavorable balance between supply and demand in European [ ] countries; the increase in production of these products being at least in part offset by the systematic bombing of synthetic plants and oil storage. The source materials and the resulting substitutes are listed in Table I. The following are the approximate gross heat equivalents of some substitutes to barrels of gasoline:

Jan 1, 1941

By George S. Miller

Now that low-carbon steel is manufactured successfully in large quantities by the Bessemer process, and threatens to displace wroughtiron for nearly all purposes, it becomes interesting to find how its Specific gravity compares with that of wrought-iron. The general name "steel" is retained in this paper to designate that metal made by the Bessemer process, which might be more properly called " ingot iron." But the former name seems to be quite firmly established in the iron trade. This steel offers many inducements to the manufacturer of architectural iron, by reason of its hornogencity, and the large masses in which it may be readily moulded. The steel from which these determinations have been made, was produced in four-ton heats and cast into ingots of about 3100 Ibs. weight, having an average section 14'' by 14". These ingots were rolled in a blooming-mill to a section about 24" by 14", cut into slabs and rolled in a plate-mill to a plate .065" to .165" thick, and about 1411 in width. The specific gravity was obtained from pieces of this plate. The metal showed by analysis .10 to .12 per cent. carbon,.33 to .45 manganese,.060 to .072 sulphur,.075 to .082 phosphorus, and .010 silicon. The samples were not annealed, but were brought to a bright surface with a file. All figures given are averages of not less than three determinations on separate pieces from the same plate. The variation in the figures from which the averages were made in no case exceeded .015.

Jan 1, 1886

By Mark R. Lamb

The various methods of treating pulp in air-agitation tanks offer problems for experiment and study which are fascinating as well as practical. The usual method heretofore has been to fill each tank in turn, agitate the mixture the required period and then discharge the treated pulp into a storage-tank, from which it is drawn to the filter as required. A later method is to run the pulp from the tube-mill, classifier, thickener, or settler into the first of a set of tanks, and thence continuously or in series through the remaining tanks, finally drawing off the pulp to a continuous filter, or to a pulp-storage tank if the filter is of the intermittent type. It is this method which I propose to discuss here in a preliminary way, with the idea of going exhaustively into the examination of the results of a series of experiments in a later paper. It may be of interest to note that the design of a cyanide-plant has recently been completed in which the estimated cost of the agitation-tanks, storage-tanks, and pumps was 30 per cent. higher for the charge-agitation arrangement than for the series plan. The first question in studying the series method is, " What is the actual period of treatment undergone by the pulp ?" One first supposes that by chance some of the pulp may get through with little or no treatment, while other portions may stay in the tanks a needlessly long period. The former is not probable or even possible, and the latter is, practically, true

Jan 1, 1910

By C. B. Jordan

LAVES and Wallbaum' have described TiRu and TiOs as having the same structure as TiFe; they had previously described the latter compound as having the CsCl structure. On the other hand, a careful investigation of the structure of TiFe by Duwez and Taylor- ailed to reveal the ordered CsCl structure, finding instead a random arrangement of titanium and iron atoms on the points of a body-centered-cubic space lattice. Consequently, it is not clear whether Laves and Wallbaum proposed the ordered or the disordered structure for TiRu and TiOs. In order to settle this question as to the structural type and to obtain values of the lattice para- meters (thereby completely determining the structures), the present investigation was undertaken. Samples having the compositions TiRu and TiOs were weighed out accurately from iodide titanium supplied by the New Jersey Zinc Co., ruthenium powder from Goldsmith Brothers Smelting & Refining Co., and osmium powder from Wildberg Brothers Smelting & Refining Co. No analysis was made of any of these metals. According to the respective analyses of the suppliers, total impurities amount to less than 0.03 pct in the titanium and to less than 0.5 pct in the osmium. The purity of the ruthenium is not known. The alloys were prepared by arc melting in a furnace of the type described by Schramm, Gordon, and Kaufmann.9 pecimens for X-ray diffraction were obtained by crushing the ingots and passing the resulting powders through a 200 mesh screen. Diffraction patterns were made with a powder

Jan 1, 1956

By Frederic P. Dewey

By the old method of determining platinum in ores and bullion, the silver-alloy first obtained in the regular course of assay is parted in strong sulphuric acid and the residual metal weighed. This is re-alloyed with silver by a second cupellation and parted in nitric acid, the residual metal being again weighed. Any difference shown between the two weighings is assumed to be, and is called, platinum. Sometimes it is SO, and if any considerable amount of platinum be present, there will be a decided difference between the two weighings; but a slight difference is no real evidence whatever of the presence of platinum. On the other hand, the second weight may equal or possibly exceed the first, even when traces of platinum are present. Again, other members of the platinum group may go into solution in nitric acid more or less. If present, these would be called platinum and escape detection. The method does not provide any direct tests whatever as to the presence or absence of platinum. It is often indecisive, and sometimes gives erroneous results. It is, therefore, quite unsatisfactory. Being called upon many times to determine platinum in a wide variety of materials, particularly when present in very small amounts, I have realized the disadvantages and defects of this old method. In an article on the solubility of gold in nitric acid,' I have briefly outlined a method of gathering a little gold out of a solution containing much silver, which furnishes the basis of

Jan 1, 1913

By J. PARK

Discussion of the paper of J. PARSE CHANNING, presented at the New York meeting, February, 1915, and printed in Bulletin No. 99, March, 1915, pp. 529 to 538. FRED H. RINDGE, JR., * New York, N. Y.-It is interesting to note that although this movement was started only seven years ago at Yale, it has spread in that brief time to 200 colleges and technical schools, anti thousands of men are interested in it. There are 3,000 graduates who became acquainted with the movement in college days anti are now promoting the industrial betterment idea all over the country. Some of these men are employed entirely in this work, and the number of such workers is constantly increasing. We feel we are really doing a very fundamental thing in getting so many coming engineers and prospective employers of labor to interest themselves in these things which we have been discussing this morning; these things which are so vital to efficiency and success in any line of business or engineering to-clay. Of course the institutions located in our large industrial centers have the greatest opportunity for practical service. But I have just returned from one college, Pennsylvania State College, where 300 engineering students in three clays signed up as interested in this movement and as anxious to take active part in the work this summer. That is one of a number of colleges situated in towns where there are 110 industrial opportunities. Therefore, their field of service must be where they work

Jan 5, 1915

By Bernard Schneider

The diversity of methods available to engineers and geologists for studying rock masses is a reflection of the fact that, despite the rapid and encouraging progress made over the last few years, there is still no unified and comprehensive method which can be used to predict the over- all behavior of a foundation. Nevertheless, it is agreed that the fundamental characteristic affecting the engineering properties of rock is fissuration, and this paper de- scribes a few new or improved methods of studying fissuration and its influence on major engineering factors such as permeability, deformability, or internal stresses in the rock volume. TESTS ON SAMPLES Conventional tests on samples using thin slices can be improved by staining the slices before cutting with certain ionic dyes which have an affinity for certain types of surface. This shows up the microdiscontinuities. For example (quoted terms are French trade names) : "Turquoise Motylhne JSA" will show up porous alteration of basic feldspars. "Vert brillant SA" is used for acid feldspars. "Fushine ASA" will show up voids in all rocks. A mixture of "Turquoise" and "Rhodamine BSA" will show up zones of alteration in all types of feldspars. With this technique, it is easy to make an optical classification of the different structural types, e.g.: (1) rocks completely free from voids; (2) rocks with microfissures, which in turn can be subdivided into (a) rocks with microfissures secant to the mineral structure, (b) rocks with microfissures parallel to the mineral structure, and (c) rocks with ran-

Jan 1, 1970

By Robert Maddin

crystal prior to, polishing in order to eliminate coring. This treatment may be accomplished by wrapping the single crystal tightly in very thin, dead soft, brass foil and annealing in the presence of air for 20 hr at 800°C. Since the wrapping encircles the sptcimen three to four times, only a very slight amount of oxidation occurs on the specimen surface. On unwrapping one of these cylindrical single crystals. in. in diam by ro in. long (72.75 pct cu, 27.23 pct Zn, 0.01 pct P11, 0.01 pct re), mall light-gray depnrrits in the form of circular arcs werenoted on the part nf the foil which had been in contact with the single crystal, Fig r. (By superim- approximatetl). These deposits, which, from their color, suggest the appearance of sublimated zinc, were found to coincide roughly with a set of octahedral planes nearly perpendicular to the rod axis. The pattern shorn in the figure held no relation to the profle of the sample since the markin~s on the crystal More annealing werc attributed to traces of cube planes. It seems very likely that the deposits were formed by sutllimation of zinc diffusing from octahrdral planes since diffusian would Eogically take place along planes of maximum atomic spacing. However, it is difficult to understand why a continuous sublimation of zinc should occur from a single crystat in contact with a wrapping roil OF the same composition, and why diffusion would take place along specific octahedral planes and in a regular pattern.

Jan 1, 1949

By B. Ladanyi, B. Hoyaux

One of the most important problems in underground works is the assessment of the stability of underground openings and the determination of loads on eventual supporting structures. Under certain stress conditions, a hard and sound rock around an unlined opening may show a tendency to rock bursting, which can be prevented by appropriate measures. On the other hand, a less competent rock even if it fails in a less violent manner may give rise to a rock load because within limited regions surrounding the opening, the failed material may have a tendency to flow into the opening; this condition should be prevented by designing a proper supporting structure. The stability of the opening, as well as the value of the design loads acting on the supports in the latter case, depends clearly on the shape, extent, and location of the failed regions, which are often called “plastic zones.” It has been known for some time how the plastic zones develop in some very simple cases, such as in the case of a circular opening in an elastic ideally plastic medium subjected to a nongravitational stress fie1d.l However, to the knowledge of the authors, no information has been available up to now about the extent of the plastic zones in a more general case and for rocklike media. ASSUMPTIONS ON ROCK BEHAVIOR MADE IN THE CALCULATION The solution shown in this chapter is valid for a horizontal tunnel of circular cross section driven through a rock medium at a finite depth.

Jan 1, 1970

By Frank Fahrenwald

INTRODUCTORY A COMPLETE list of the elements as given for 1915 includes 18 that melt above 1,700° C. There does not exist one complete thermal equilibrium diagram for any pair of these 18 elements. Several of these elements have been combined, in relatively small proportions, with metals of lower melting point: e.g., tungsten, molybdenum, and vanadium, in steels, or with nickel and cobalt; but of this refractory group, platinum is the only one that has been extensively studied in this connection. When one considers that, with few exceptions, the industries have made use of alloys to the exclusion of pure .metals, it is reasonable to expect that alloys of this refractory group will invade fields in which the pure metals have found little application. The past neglect of this class of metals has, no doubt, been partly due to the rarity of some of them, for even though alloys of very valuable properties should be developed, their cost, unless in exceptional applications, would be prohibitive. There is also a well-founded reluctance to undertake research involving very high temperatures which, in the case of most of these elements, must be accompanied by an inert atmosphere as well. This combination of high temperatures* and control of atmosphere within the heating chamber of any furnace of present design is a difficult problem. It is the purpose of this paper to give results,1 of an investigation of one binary series of this group, in which methods were employed that avoided the usual difficulties accompanying high-temperature alloy investigation.

Jan 6, 1916

Discussion of the paper of J. V. EMMONS, presented at the Pittsburgh meeting, October, 1914. and printed in Bulletin No. 93, September, 1914, pp. 2233 to 2248. ALBERT SAUVEUR, Cambridge, Mass.-Mr. Emmons is to be congratulated for having placed before us in so forcible and satisfactory a manner a question of much importance-that of the surface decarbonization of steel. Of course, both manufacturers and consumers have known for many years that during the heat treatment of high-carbon steel, surface deca.rbonization is always likely to occur to a greater or less degree, but the subject does not seem to have been investigated with the method and thoroughness it deserves. I am in substantial agreement with Mr. Emmons's conclusions, and I have but little to add to what he has so well said. His statement that carbon dioxide is just as effective an oxidizing agent as pure oxygen is likely to cause surprise and some will wonder whether his investigation has been carried far enough to warrant so unexpected a conclusion. The reaction C + 0 = CO, expressing the oxidation of carbon by pure oxygen, is decidedly exothermic, whereas the reaction C + C02 = 2C0, expressing the oxidation of carbon by carbon dioxide, is endothermic. Decarburization by pure oxygen, therefore, should take place much more readily than by carbon dioxide. One cannot help regretting that the author does not mention' the best way of preventing in a practical manner surface decarbonization while treating tool steel and other high-carbon steels.

Jan 4, 1915