Search Documents

By Ralph V. Higgins

This paper concerns the magnitude of the amount of supersaturation that occurs in an underground reservoir during the flow of oil and gas to wells and to the amount of undersaturation that occurs during repres-suring of an oil reservoir where some effective permeability to gas exists. The study is based on earlier laboratory findings of other investigators on the rate of diffusion of gas in oil as a function of the depth of oil. Utilizing these relationships and the principles of reservoir mechanics, a quantitative estimate of undersaturation and super-saturation was calculated. The results showed that the diffusion of the gas is rapid enough that for all practical purposes no supersaturation exists during the flow of oil to wells or undersaturation during repressuring in reservoir sands having some effective permeability to gas. The reason diffusion of the gas virtually keeps the oil saturated is the long time required in radial flow for oil to reach the well and the slow rate at which pressure in reservoirs is increased during repressuring. INTRODUCTION Knowledge of the phase relationships during flow of gas and oil in an underground reservoir is essential to operating the reservoir in the most efficient manner. In material-balance calculations and in fluid-flow studies, the oil is assumed to contain all the gas that it will dissolve at given temperature and pressure. Pressure-volume-temperature relationships are normally obtained in the laboratory using "bottom-hole" or combined samples of the reservoir fluids. In such laboratory determinations equilibrium is obtained between the oil and gas in the pressure cells by mechanical agitation. During the flow of oil and gas in reservoirs, however, no comparable agitation occurs to mix thoroughly these fluids to aid in effecting equilibrium between the two phases. During repressuring of a partly depleted underground reservoir, the gas is usually injected into the reservoir faster than the oil can absorb it; consequently, the oil is undersaturated. On the other hand, as the oil flows through the reservoir to the wells during producing operations the pressure decreases faster than the gas in solution can diffuse through the oil to the gas phase. The oil therefore is supersaturated with gas. Where the oil is undersaturated, gas diffuses away from the gas-oil interface, and where it is supersaturated the gas diffuses toward the interface. In either case the gas moves from a higher to a lower saturation. This report contains the results of a study of the factors influencing the degree of nonequilibrium of the phase relations of oil and gas in porous mediums during the flow of oil through reservoirs to wells and also during the injection of gas into partially depleted sands. Data from an underground reservoir are presented and the degree of supersaturation during the flow of the oil through the reservoir to the well is approximated. Also data from another reservoir are used and the degree of undersaturation during the repressuring operation is calculated. In addition, the flow rates of oil in laboratory experiments and in underground reservoirs are compared, as data from the laboratory are often used to interpret events in the reservoir, and the rates of flow influence appreciably the degree of nonequilibrium. Much of the contents of this report was prepared in 1943; but, because of other activities during and since the war, the manuscript was left untouched until 1952, when it was decided to include an estimate of the amount of undersaturation during repressuring as well as supersaturation during flow.

Jan 1, 1955

By K. P. Gupta

The Cb-rich boundary of the (Cb,Al) a phase field at 1250OC is near 41 pct Al. The Al atoms tend to occupy the C. N. 12 sites in this structure. A homologous (Ta,Al)a phase was identified. No a phase was found in the Mo-Al system at 1200°C. The first binary o-phase with a non-transition element as a major component was found1,2 in the Cb-Al system. The composition of this phase was reported2 as approximately 34 at. pct Al, based on X-ray diffraction patterns taken of alloys in the as-cast condition. Further study of the composition of this o-phase, therefore, appeared desirable. Since Si was previously found3,4 to occupy preferentially the lowest C.N. sites (I and IV) in the a phase, and preliminary resultsa indicated that Al may show similar ordering, one of the aims of the present work was to obtain more complete information on ordering in (Cb, Al) o. Among the binary systems of Al with Ti-, V-, and Cr-group elements, the Ti-Al, Zr-Al, V-Al, and Cr-Al systems are known to comprise no o-phase. In the present work a Ta-Al and a Mo-Al alloy were studied in an effort to find additional o phases with Al as a major component. EXPERIMENTAL PROCEDURES AND RESULTS An alloy with the intended composition of Ta + 40 at. pct Al was prepared by arc melting in He atmosphere. In both the as-cast condition and after annealing for 10 days at 1250°C and quenching in cold water this alloy consisted of two phases, as seen in the X-ray pattern and the microstructure. One of these phases was identified as the o-phase; the observed and calculated d-spacings are shown in Table I. The lattice parameters of this o-phase are a = 9.972 A, c = 5.214 A and c/a =0.5228, as determined from a Debye-Scherrer pattern using Fe K a radiation. The d-spacings for the unknown second phase are given in Table 11. The alloy contained approximately 25 pct of the unknown phase after annealing, as estimated on the basis of microscopic examination. A Mo-Al alloy was prepared by arc melting, with an intended Al-content of 35 at. pct. The alloy button was annealed for 7 days at 1200°C and water quenched. The X-ray pattern of the alloy in both the as-cast and the annealed state showed the reflections of Mo3Al (Cr30 type structure) and an unknown phase different from a. Six Cb-Al alloys were prepared in the composition range 30 to 50 pct Al. All alloys were arc melted in He atmosphere. After annealing for three days at 1175oC in evacuated silica capsules and quenching in water, the alloys with 30 to 40 pct Al contained three phases, namely the o-phase, Cb3Al (Cr3O-type structure) and an unknown phase. The alloys with more than 40 pct Al contained two phases, namely, what appeared metallographically, the o-phase and the same unknown phase. In the alloys containing less that 38 pct Al, the unknown phase was not present after annealing for 4 days at 1250°c,

Jan 1, 1962

By S. L. Couling, D. J-P. Adenis

i2) twinning in poly crystalline magnesium does not usually occur homogeneously but is concentrated in localized regions or bands inclined at about 45 deg to the stress axis. These bands of twinning are in many ways similar to the Luders bands seen in mild steel alzd Al-Mg alloys. Within a hand the percentage of the volume twinned may approach 100 with no twinning outside the band. Bands are not produced in specimens of grain size a3 x 10-= in. or in samples deformed at temperatures 300°F. Annealing of heavily twinned regions leads to re crystallization textures markedly different from those found in the starting material. The exact preferred orientation appears to depend on the starting grain size, the amount of compres-sive strain and the manner in which it is introduced. MAGNESIUM, with its hexagonal crystal structure, deforms plastically at room temperature by a variety of deformation mechanisms, one of the most important of which is (1012) twinning. In single crystals such twinning occurs on compression parallel to the basal plane or tension perpendicular to it. In wrought polycrystalline magnesium, such as rolled sheet, the preferred orientation is such that almost all the grains have their basal planes nearly parallel to the sheet surface. Therefore, if sheet material is deformed by cold rolling or by tension in the plane of the sheet, deformation of the grains by (1012) twinning is not favored. On the other hand, twins form readily on compression parallel to the plane of the sheet as in a compression test, on the compression side of a bent sample, or at the outer rim of a drawn cup. The first part of this paper deals with the morphology of (1012) twinning in polycrystalline magnesium. Some aspects of this subject were covered by Barrett and ~aller.' Of direct bearing on the work to be reported here are the comments of Jetter' in discussion to Ref. 1. He shows that Mg + 1.5 pct Mn alloy sheet when bent about a transverse axis develops a pattern of transverse bands on the surface of compression. A longitudinal section through the sheet shows that the bands are wedge-shaped and inclined to the rolling direction. The bands were identified as "outcrops of regions in which deformation is localized as the result of the reorientation brought about by (1012) twinning". The second part of the paper treats the recrys-tallization texture of the specimens twinned by compression. Magnesium deformed and then annealed generally recrystallizes with no change in orientation.1'3'4 This statement is true provided that the amount of (1012) twinning occurring during deformation is small. In an isolated observation, Anse15 has shown that, when deformation produces much (1072) twinning, annealing causes new maxima to appear in the pole figure. The second part of the paper elaborates on this point. I) MATERIALS AND PROCEDURES All of the experimental work to be reported was done using the commercial sheet and plate alloy AZ31B (nominal composition: 3 pct Al, 1 pct Zn, 0.4 pct Mn, balance magnesium). This alloy is available commercially in two tempers, -0 (fully annealed) and -H24 (partially annealed), and specimens of both tempers were used in various experiments. The average grain. diameter (AGD) for -0 temper 0.125-in. sheet is about 0.5 x 10- in.; where material of larger grain size was desired, anneals at elevated temperature were used to grow the grains. compression tests were made on a screw-driven "hard" machine. The specimens were clamped in a

Jan 1, 1964

By Charles Law McCabe, Lyndon H. Everett, Edna A. Dancy

It has been found that the carbide phase present at equilibrium in the system M-H2-CH4, at about 600°C, is MC for the rare-earth metals Ce and Pr. X-ray diffraction analysis showed that the monocarbides have fcc structures with lattice constants of 5.036 + 0.009Å and 5.131 + 0.001Å for CeC and PrC respectively. Gaseous equilibrium measurements were used to calculate the standard free energy of formation of the monocarbides from the elements. for the formation of (+ 1300) for the formation of PrC. THE rare-earthdicarbides, and their crystal structures, have been known for some years,l but only more recently were the carbides CeC,2,3 Ce2C3 2 and CeCS3 reported. In 1958 to 1959, Spedding et al. published work on the lanthanum-carbon system4 and other rare-earth metal-carbon systems,5 proving the existence of M2C3 and MC2, and measuring the lattice constants. They also demonstrated that tri-rare earth carbides, M3C, exist for the rare-earth metals samarium through ytterbium. However, they concluded that the cerium monocarbide reported by Brewer and Krikorian2 and by Warf,3 and given a fcc structure with a lattice constant of 5.130Å bythe former workers, was, in fact, cerium metal with carbon dissolved in it. They were also unable to find any evidence for the existence of Warf's CeC3, for which no structural details had been given. Even more recently, Palenik22 reported the existence of only M2C3 and MC2, having been unable to find any evidence for the existence of any other rare-earth carbides. There are no published experimentally derived thermodynamic data for the formation of any of these carbides, although Brewer and Krikorian6 have estimated values of for CeC, Ce2C3 and CeC2. The objective of the present investigation was; to determine experimentally the free energy of formation of any of the reported carbides of cerium and praseodymium, through a study of the rare-earth metal-hydrogen equilibrium. EXPERIMENTAL A methane-hydrogen mixture was circulated, in a closed system over previously prepared cerium or praseodymium hydride, and when equilibrium had been attained, the gas mixture was analyzed by selectively oxidizing the hydrogen and condensing out the water formed. The metal hydrides were used as starting material for convenience because, otherwise, the hydrogen in the gas mixture would immediately dissolve in the metals; in addition, the metals would not react with methane alone at the experimental temperature (around 600°C). The circulating system was based on that used by Browning, DeWitt, and Emmett7 for similar studies on iron carbides. It consisted of a quartz reaction vessel, all-glass circulating pump, analysis tube containing copper oxide that could be heated to 300" C by means of a small furnace, a solid CO2-methanol trap, and a double limb absolute manometer, Fig. 1. A cathetometer, capable of reading to 0.005 cm, was used to measure the difference in height between the two columns of mercury. In its final form, the reaction vessel was enclosed in an outer jacket, containing approximately the same pressure of hydrogen as that within, to reduce errors due to diffusion of hydrogen out through the fused silica of the reaction vessel., The circulating system was supplied with

Jan 1, 1962

By Frederick V. Lawrence

Broadly speaking, fluxes are substances which promote wetting and spreading or enhance the fluidity and manipulative properties of materials in joining, fusion, and smelting operations. The term most strictly applies to substances used to facilitate soldering and brazing; but in the discussion which follows, the definition will be broadened to include materials used to promote fusion in arc welding and which aid in the smelting of metals. In each of the mentioned applications, the role of flux and its composition differs considerably; consequently in the discussion which follows, fluxes for soldering, brazing, arc welding, and smelting applications will be considered separately. Soldering and Brazing Fluxes Soldering and brazing are metallurgical joining processes in which a joint is formed using a filler metal of composition dissimilar to that of the joined pieces (base metal). The filler metal, solder or braze, is always of lower melting point than the base metal. Consequently with these processes there is no melting of the base metal. The successful creation of the joint depends upon the wetting and spreading of the solder or braze around or throughout the joint. The obstacles to successful soldering and brazing are contaminants and tenacious oxide films on the metal surfaces. In soldering and brazing applications, fluxes act to remove and exclude oxides and other impurities from the joint. There is no fundamental difference between soldering and brazing. The distinction between them is made on the basis of temperature. Join¬ing operations carried out at temperatures above 500° C are termed brazing. The higher temperatures used in brazing enable higher melting point filler metals to be used which generally provide stronger joints. The higher temperatures of brazing processes also require fluxes which are substantially different from those used in soldering and which will remain effective at high temperatures. Consequently the distinction between soldering and brazing can also be made on the basis of the fluxes used. Soldering Fluxes Even thoroughly cleaned and degreased, metal surfaces still possess tenacious oxide films which inhibit the soldering of the joint. The reactions which form these films increase with increasing temperature. The rate of oxide formation and the tenacity of the film varies with each base metal. Aluminum, magnesium, stainless and high alloy steels, aluminum and silicon bronzes when exposed to air form hard, adherent oxide films. These metals require highly active and corrosive fluxes to remove and prevent the reformation of oxide films during soldering. Metals such as copper and silver, on the contrary, form less tenacious films at a lower rate, so that mild fluxes are sufficient. Soldering fluxes must dissolve or remove oxides and promote rapid wetting and spreading of the solder. The flux removes the oxide film by loosening and floating it off into the main body of the flux. The oxide removal is often aided by the alloying of the solder with the base metal, undermining small areas of the oxide and detaching them (Anon., 1959). The flux coagulates and suspends the oxide particles which have been loosened. The flux forms a protective cover preventing the reformation of the oxides, permitting the spreading of the solder and the formation of a metallic bond between the solder and the base metal. Constituents of Soldering Fluxes: Soldering fluxes are commonly grouped into three categories: highly corrosive, intermediate, and noncorrosive. One normally would choose to use the least corrosive flux which will give satisfactory performance.

Jan 1, 1983

By P. Shahinian, R. L. Stegman, M. R. Achter

Creep strength has been determined as a function of oxygen pressure for nickel at 510" and 600°C. Creep-rupture life drops from its highest value at the ultimate vacuum of 10-7 torr to a high pressure plateau of nearly constant life which, at 600°C, commences at torr. This behavior is described in terms of a model that relates surface gas adsorption and the generation of fresh crack surfaces. In a calculation based a this model the predicted pressure beyond which the creep strength should not decrease further has been found to agree well with the observed value. The introduction of oxygen during creep in vacuum was found to cause a prompt rise of the creep rate. The magnitude of the environmental effect was much less than generally observed in fatigue and this is attributed to the diffarent crack morphologies in creep and fatigue. GASEOUS environments are known to affect creep resistance adversely1-5 but the effects have received less attention than the much larger ones in fatigue. At low temperatures it has been shown for nickel that the creep rates are faster and the rupture lives are shorter in air than in vacuum and that these environmental effects can be correlated with faster crack growth rates in the reactive environment.' In support of a mechanism of gas adsorption at the crack tip to explain the above effects, a calculation based on kinetic gas theory showed that surface coverage by gas was not as rapid as the exposure of fresh metal at the crack tip in the ultimate vacuum but was in air.7 In fatigue a number of investigations have demonstrated that the reduction of life with gas pressure usually follows a step curve with most of the reduction occurring in a transition range at intermediate pressures and little or no change at high and low pressure.8 There have been no studies, however, in which creep strength has been determined as a function of reactive gas pressure to see whether similar effects would be found. This investigation was undertaken to study the kinetics of the environmental effect in the creep of nickel. EXPERIMENTAL PROCEDURES The environmental creep apparatus was constructed to minimize many of the experimental conditions which can cause scatter in data. Dead weight loading is employed and weights are contained within the environmental chamber to eliminate bellows and the necessity for compensation for gas pressure changes. Elongation over the specimen gage length is recorded from a Riehle Model DV Controlled Environment Extensometer which provides readout to 2.5 x 10- in. Temperature is monitored and controlled from a thermocouple at- tached to the specimen gage length to +0.5oC or better. The freon trapped oil diffusion pump vacuum system included an auxiliary liquid nitrogen trap and, with a wide range variable conductance leak valve, pressures from the ultimate vacuum of 10"7 to l03 torr of any desired gas are obtainable. Pressure is measured by means of a hot filament ionization gage below 10"3 torr and a NRC Model 530 Alphatron Vacuum Gauge above 10-3 torr. The oxygen, which was leaked into the environmental chamber, was an Aviator's Grade of 99.5 pct purity with a dew point of -80°F. Analysis of the nominal 99.8 pct Ni showed the following percentages of major impurities: 0.02 C, 4.01 Mn, 0.005 Si, 0.01 Cu, 0.02 Fe, and 0.034 Mg. Cylindrical specimens were machined with a 0.180

Jan 1, 1970

By C. R. Criss, R. J. McCormick

ThiS paper .summarizes the development and perform. ance of the Coldwater Oil field, Isabella County, Mich. Production is obtained at a depth of 3750 ft from a dolomite reservoir, which is probably both Rogers City and Dundee. There appears to be no persistent barrier to vertical fluid movement between the Rogers City and Dundee, and both formations are believed to have a common original oil-water contact. No we1ls are open to production at the level of the Dundee. The discovery of the field in 1944 was followed by the drilling of 81 producing wells and nine dry holes. By the end of 1952, the field had produced 12,763,000 bbl of oil, at which time 69 active wells were producing 3600 B/D oil and 21,000 B/D water. The reservoir has an effective natural water drive, and bottom-hole pressure has declined 75 psi from an original pressure of 1453 psi. Oil is undersaturated at reservoir conditions with a solution GOR of 512 cu ft/bbl and a saturation pressure of 1190 psi. INTRODUCTION Although the Coldwater Field is now in its ninth year of production, it ranks seventh in cumulative recovery, and second in current daily oil production in the State. Following complete development of the field in 1946, it has consistently contributed approximately 11 per cent of Michigan's daily production. Coldwater appears to have a greater pay thickness than most fields producing from the Rogers City forma- tion in the west central part of the Michigan basin. Except as influenced by the extent of closure and the thickness of the oil column, reservoir performance is believed to be representative of Rogers City fields in this part of the basin. For this reason, it is felt that the following presentation of factual data for the field will be of general interest. HISTORY AND DEVELOPMENT Discovery of the Coldwater field during Aug., 1944, followed favorable subsurface geological correlations and core tests drilled to a shallow stratigraphic marker horizon. The field is located in the west central part of the Michigan Basin in Coldwater Township (T16N-R6W), Isabella County. It is 60 miles west-northwest of Bay City, and near the geographic center of the southern peninsula of Michigan. The discovery well flowed 200 bbl of oil the first 24 hours from the Rogers City dolomite at a depth of approximately 3750 ft. Field production is principally from the Rogers City with a minor amount assumed to come from the underlying Dundee dolomite, although none of the wells are open to production at the level of the Dundee. Both the Rogers City and Dundee formations belong to the Devonian system (See Geologic Column-Fig. I.) In addition to Rogers City-Dundee oil production, sweet gas is produced from the Michigan Stray sand of the Mississippian system at a depth of 1400 ft. The gas reservoir has approximately the same areal extent as the underlying oil reservoir. Although gas production is an important feature of the Coldwater field, this report is concerned only with the oil reservoir. The productive area is approximately 3200 acres. The pool is developed on a 40 acre spacing pattern with wells drilled in the center of the north half of 40 acre tracts, except for a few off-pattern wells drilled along

Jan 1, 1955

By N. Marusov, D. K. Lowe, J. C. Karp

This paper considers, from an engineering viewpoint, several factors involved in creating, designing and locating horizontal barriers for controlling water coning. This is an effort to consolidate new concepts with previous information so that a reasonable selection of barrier materials, dimensions and vertical position can be made. Coning theories previously developed are briefly reviewed and an effort i,s made to reduce the results of coning-theory calculations to a point where routine calculations can be made with a desk calculator. It is expected that these simplified calculations will give usable predictions of the amounts of improvement attainable with barriers of various dimensions. Apparatus and procedures used for testing the suitability of commercial cements are described and test results are presented. INTRODUCTION Just about as soon as the phenomenon of water coning was recognized as an oilfield problem, there were suggestions that the production of water coning could be controlled or completely suppressed by means of horizontal barriers. It was also suggested that natural barriers such as shale streaks were helpful in restricting bottom-water production. The implication was that wells not having the benefit of continuous shale streaks to suppress bottom waters should, in some way, be supplied with an artificial barrier. With regard to the selection of barrier materials, there are many references which give the merits of liquid barriers.',' These liquids include surface-active agents," recipitates' and emu1sions. There is no real need to review the merits of these materials again. This paper deals with the use of solid barriers which could be made from various cements. The two major restrictions placed on these barrier cements are that (1) they must be commercially available in large quantities, and (2) they must be applicable by means of standard tools and equipment with techniques that have been fully developed and are in general use at the present time. A schematic drawing of a horizontal barrier in a reservoir is shown in Fig. 1. Two maximum stable water cones are illustrated-—-one for the wellbore diameter and the other for a barrier. A maximum stable cone is one that has attained its maximum volume at the critical production rate and is on the threshold of producing water. The volume displaced by each water cone and the rise in water table are indications of the amount of water-free oil produced. Corrections for porosity, connate water and residual oil, of course, must be applied. The water-oil interface which defines a maximum stable cone is called a free surface. It is a surface over which the pressure is constant. This free surface has the shape of a limiting streamline at and below which there is no movement or transport. The shape of the water cone describes the pressure drop in the reservoir. The effect of a completely impermeable barrier on the cone shape is essentially the same as extending the wellbore out to the barrier radius. The placement of a horizontal barrier requires that a horizontal fracture be created using a single-point entry technique. Two methods may be employed for filling this fracture. One method consists of propping the fracture before filling with cement. The other consists of fracturing with fracture fluid, then immediately following with cement

By Donald E. Grimes

In conjunction with Inland Steel&apos;s development of lead-bearing steels possessing improved machin-ability because of tellurium and/or selenium additions, it was decided to determine liquidus and solidus temperatures in the Pb-PbTe-PbSe sub-ternary system. With the exception of alloys in the PbTe-PbSe system, it is believed that no previous study of this subternary has been performed. Thermal analysis was employed in a general survey of the subternary. In addition to PbTe, PbSe, and pure lead, ten ternary compositions were selected at intervals of ten at. pct. Sixty-gram alloys were prepared by sealing an appropriate mixture of the elements in quartz crucibles with a central thermocouple-well under a vacuum of less than 10 p. All three elements were 99.999+ pct pure with only trace impurities detected by spectroscopic examination. After the alloys had been heated at least 20°C above the liquidus in a Kanthal furnace, cooling and heating curves were obtained. Two or more cooling curves were employed both for the determination of each alloy liquidus and for the solidus of those al- loys containing greater than 50 at. pct Pb. Cooling rates were 0.5° to 3.5°C per min during the 5 min immediately prior to the start or end of solidification. For those ternary alloys containing 50 at. pct Pb, the solidus was determined from heating curves. Temperatures were measured with a Pt/Pt-10 pct Rh thermocouple which was calibrated in the same apparatus against the freezing points of zinc (A. D. MacKay—99.999 pct), antimony (A. D. MacKay-99.999 pct), and copper (ASARCO—99.999+ pct) both before and after the experimentation. The only interruptions in the continuous strip-chart recording of the temperature occurred for brief periods at significant points of interest when direct readings were made with a Rubicon Type B potentiometer sensitive to * 1 µv. The average liquidus and solidus temperatures obtained in this investigation are listed in Table I together with probable errors based on the accuracy of the thermocouple calibration and the reproduci-bility of the data. No chemical analyses of the alloys were performed because the synthetic or as-charged compositions were felt to be reliable. The melting points obtained for PbTe (924.7° ± 0.7°C) and PbSe (1084.0° ± 0.6°C) compare favorably with recent findings of other investigators.&apos;-&apos; As indicated in Table I, both the liquidus and solidus temperatures increase as selenium replaces tellurium for a constant atomic percent lead. As a result, the ternary liquidus and solidus temperatures for a given percent lead lie between the corresponding binary temperatures published in the literature. It should be noted that those ternary alloys containing 50 at. pct Pb exhibit a relatively narrow liquid-plus-solid region (<80°C) when compared with alloys containing greater than 50 at. pct Pb. Alloys with 60, 70, or 80 at. pct Pb not only have a much wider liquid-plus-solid region (>500°C) but also exhibit considerably lower and approximately constant solidus temperatures which thus form a virtually isothermal solidus "plane" slightly below the melting point of pure lead (327.3°C). For these alloys

Jan 1, 1965

By Will Mitchell, Ford F. Miskell, C. L. Sollenberger

Heat treatment of ore prior to comminution reduces power requirements for grinding, reduces grinding media wear, and improves recovery of iron values from a typical Minnesota magnetic taconite. Test data demonstrating this, as well as an analysis of the economics of commercial application of the technique, are presented. THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators1-" ave noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilitiesh nd by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat- treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported7 to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of&apos; this portion is shown in Table I and an approximate mineralogi-cal analysis is shown in Table 11. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of —6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1953

By J. G. Richardson, F. M. Perkins

Results and procedures are pre-cented covering a laboratory investigation of the effect of rate of water advance on the displacement of oil from clean water-wet sands. The experiments included water floods at atmospheric pressure with and without gas present over a range of flow rates from reservoir rates to rates ten thousand-fold higher. Water floods were also conducted at various rates at elevated pressure with no gas present. Other tests were made at elevated pressures by forming a free gas saturation by evolution of gas from solution in the oil before water flooding. Recovery of oil was found to be independent of the rate of water advance with or without gas present and independent of the pressure level of the water flood. A dimensionally-scaled model of a reservoir composed of a thick uniform sand was used to study the effect of rate on the tendency of water to underrun the oil because of the greater density of the water. Another model was used to study the effect of rate on the tendency of water to channel down the more permeable sand in a stratified reservoir composed of sands of diffierent per-meability in intimate contact. The effect of the presence of gas on the flooding conformance was studied with both models. The results obtained using these simple models provide a basis for predicting behavior in more complicated systems. INTRODUCTION In spite of the great amount of research on the flow of fluids in porous rocks, there still exists some disagreement as to the influence of the rate of water advance on the displacement of oil by water flooding. Various investigators have found that increasing the rate of water injection would decrease, increase, or have no effect on recovery of oil. One reason for this disagreement has been a lack of understanding of the effects of the capillary forces which influence the results obtained in the laboratory at low rates with short columns. Other causes of the disagreement have undoubtedly been inconstancy and uncertainty of the wetting properties of the porous media studied, inaccurate saturation determinations, and in some instances conclusions based on insufficient data. Capillary forces are involved in the displacement of oil by water in two ways. On the microscopic scale, the capillary forces control the dis- tribution of oil and water in the pore spaces of the sand. The magnitude of these forces is governed by the preference of the sand to be wet by water, the pore sizes and geometrical shapes, and the interfacial tension between the water and oil. On the macroscopic scale, differences in saturation at the flooding "front" when water displaces oil result in capillary pressure gradients. These gradients cause water to flow preferentially ahead of the front. In short laboratory columns at low rates, the front can span the entire column length. Also, at the outflow boundary the preference of sand to be wetted by water results in retention of water and a high water saturation in the region of the outflow face. This effect is commonly called the boundary effect.&apos; The capillary pressure gradients which complicate the interpretation of flooding performance of short laboratory columns at low rates of water advance become negligibly small under certain conditions. The conditions where capillary pressure gradients are negligible are in long, homogeneous reservoir sands,&apos; at high rates of water advance in short laboratory columns,3 and at any rate in laboratory columns as the residual oil saturation is approached. Thus, laboratory water floods, conducted

Jan 1, 1958

SEC. 1. The membership of the Institute shall comprise seven classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members; 7. Junior Foreign Affiliates. All shall be equally entitled to the privileges of membership, excepting that no member of any class whose residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the class of Member must be at least 27 years of age and must have had at least six years&apos; employ¬ment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members. SEC. 3. Honorary Members: Each candidate for Honorary Membership must be recommended by at least ten Members and must be elected by ballot at a meeting of the Board of Directors by the unanimous vote of the Directors present; provided, how¬ever, that the number of Honorary Members shall at no time exceed twenty. Such election shall automatically act as a transfer of such member from any other class of membership to which he may belong. SEC. 4. -Senior Members: The Directors may in their discretion place on the Honor Roll of Senior Members and transfer from any other class of membership other than Honorary Membership the name of any Member or Associate who has reached the age of seventy years and who has paid dues for thirty years, and for good reasons in special cases may vary the age or number of years. SEC. 5. Junior Members: A person to be eligible for election to the class of Junior Member must be qualified through education or experience to hold a subordinate position in engineering, mining, metallurgical, geological or chemical work. He shall be not more than 33 years of age at the time of election. SEC. 6. Associates: A person eligible for election or transfer into the class of Associate shall be one, who, in the opinion of the Committee on Admissions and the Board of Directors, is suitable for such election or transfer by reason of his interest in or connection with mining, geology, metallurgy, or chemistry. SEC. 7. Rocky Mountain Members: Membership in a special class of life member¬ships without annual or other dues and without right to receive the printed literature distributed to other members or the right and privilege of wearing the official badge of technical members, is given to all members of the Rocky Mountain Club at the time of consolidation. These special Rocky Mountain memberships shall be claimable by any member of the Rocky Mountain Club, not already a member of the Institute, availing himself of the privilege within ninety days after mailing of notice to him, by the Secretary of the Institute. SEC. 8. Junior Foreign Afliate: Upon appropriate action by the Board of Direc¬tors and with its approval, members in good standing of any technical society having its headquarters outside of the United States of America, Canada, or Mexico,

Jan 1, 1937

By L. L. Gray, D. W. Reed, F. Morgan

A flowMeter has been developed at Gulf Research and Development Co. and tested in the field for measuring the flow of gas in well bores. It has been used in a study of the injection capacity of different horizons in gas injection wells in Oklahoma. The flow sensitive element of the meter is a semi-conductor having a very high temperature coefficient of resistance. Advantages possessed by this meter are the result of that property and the high specific resistance of the element. The instrument possesses a sensitivity considerably higher than any reported previously. In the application described here the element is heated to a temperature considerably above ambient by an electric current, which is supplied by a voltage source at the surface. When fluid flows through the meter the rate of dissipation of heat is increased and the temperature of the element decreases. Because of the negative temperature characteristics of the resistance element such a decrease of temperature will be accompanied by an increase of resistance which, under flow conditions ordinarily found in wells, is of such a magnitude that it can be directly measured or recorded in terms of a change in voltage at the surface. In practice, rate of flow is measured in terms of the drop in voltage in the resistance element. All the metering and control apparatus remains at the surface while the thermal element is lowered into the well on a single conductor cable, consisting of an insulated wire and sheath. The meter is calibrated by passing known quantities of gas through it either at the surface or in the hole at a point immediately above the region in which gas is lost to the formation. In case calibration is made at the surface, the ambient temperature in the hole may readily be obtained by a second resistance element which is operated at a current so low that effectively no heating occurs. The instrument has been adapted to con-tinuous recording, but the velocity of the meter relative to that of the gas must be low unless corrections are made. Curves giving data obtained in actual field tests are shown&apos; The meter can also be used to determine the distribution of flow capacity in a gas producing well. A differential form of the meter has been designed and built in which the local flow or injection capacity of the formation is obtained directly. Introduction When fluid is injected into a well in a secondary recovery or pressure-maintenance operation the question of its most effective use invariably arises. Although the core log, when available, will show the regions of good permeability and oil saturation, there is normally no assurance that the fluid actually enters the formation in zones where injection is deemed desirable. In view of the uncertainties involved in such programs, it is generally conceded that measurements of permeability for a formation in place are more significant than those obtained by the core-sampling technique. A subsurface meter has been developed at the Gulf Research and Development Co. for measuring flow of fluids at different horizons in a well bore, and field tests have been made on the instrument in Cooperation with the Tulsa Division of the Gulf Oil Corp. In this paper the meter is de-

Jan 1, 1948

By F. Morgan, L. L. Gray, D. W. Reed

A flowMeter has been developed at Gulf Research and Development Co. and tested in the field for measuring the flow of gas in well bores. It has been used in a study of the injection capacity of different horizons in gas injection wells in Oklahoma. The flow sensitive element of the meter is a semi-conductor having a very high temperature coefficient of resistance. Advantages possessed by this meter are the result of that property and the high specific resistance of the element. The instrument possesses a sensitivity considerably higher than any reported previously. In the application described here the element is heated to a temperature considerably above ambient by an electric current, which is supplied by a voltage source at the surface. When fluid flows through the meter the rate of dissipation of heat is increased and the temperature of the element decreases. Because of the negative temperature characteristics of the resistance element such a decrease of temperature will be accompanied by an increase of resistance which, under flow conditions ordinarily found in wells, is of such a magnitude that it can be directly measured or recorded in terms of a change in voltage at the surface. In practice, rate of flow is measured in terms of the drop in voltage in the resistance element. All the metering and control apparatus remains at the surface while the thermal element is lowered into the well on a single conductor cable, consisting of an insulated wire and sheath. The meter is calibrated by passing known quantities of gas through it either at the surface or in the hole at a point immediately above the region in which gas is lost to the formation. In case calibration is made at the surface, the ambient temperature in the hole may readily be obtained by a second resistance element which is operated at a current so low that effectively no heating occurs. The instrument has been adapted to con-tinuous recording, but the velocity of the meter relative to that of the gas must be low unless corrections are made. Curves giving data obtained in actual field tests are shown&apos; The meter can also be used to determine the distribution of flow capacity in a gas producing well. A differential form of the meter has been designed and built in which the local flow or injection capacity of the formation is obtained directly. Introduction When fluid is injected into a well in a secondary recovery or pressure-maintenance operation the question of its most effective use invariably arises. Although the core log, when available, will show the regions of good permeability and oil saturation, there is normally no assurance that the fluid actually enters the formation in zones where injection is deemed desirable. In view of the uncertainties involved in such programs, it is generally conceded that measurements of permeability for a formation in place are more significant than those obtained by the core-sampling technique. A subsurface meter has been developed at the Gulf Research and Development Co. for measuring flow of fluids at different horizons in a well bore, and field tests have been made on the instrument in Cooperation with the Tulsa Division of the Gulf Oil Corp. In this paper the meter is de-

Jan 1, 1948

By Jei Y. Choi, P. G. Shewmon

Using a scratch smoothing technique, the magnitude and the ratio of the surface diffusion coefficients (D,) in two orthogonal directions have been measured on copper for over 100 different surface orientations. Anisotropy was found for all surface orientations except those lying near the (100) and (111); however, these anisotropies were rarely greater than 2.0. The direction of maximum D, appears to coincide with the direction of step edges on any given surface, and if no such steps exist, no anisotropy is found. Thus the jump frequency along a step edge is shown to be faster than the frequency of a jump over the step. The values of Ds and AH for the (100) and the (111) orientations agree quite well with those obtained earlier by the grain boundary grooving technique. It is proven that the directions of maximum and minimum D, (the principal axes) for any surface orientation are known if the perfectly ordered plane corresponding to the given surface orientation possesses a plane of mirror symmetry. Thus the principal axes of D, for orientations lying along the sides of the unit stereo-graphic triangle are always known independent of the extent of thermal disorder or impurity adsorption. The merits and shortcomings of King and Mullins&apos; recently published equations relating Ds to the rate of scratch smoothing are discussed. 1N an earlier paper the authors have reported the variation of the surface diffusion coefficient (Ds) with surface orientation on copper.&apos; In that study Ds was determined from the rate of growth of grain boundary grooves on symmetric bicrystals. This gave values of Ds from 850° to 1070°C in a given direction on each of the six surfaces. It was found that the activation energy for surface diffusion was essentially the same for all six surfaces. The theory developed to explain these data assumed that the free energy of any given type of surface site depends only on the number of nearest neighbors the atom has. This same theory predicted that on any given surface Ds should be independent of direction. The primary aim of this study was to check the validity of this prediction for a wide range of surface orientations on copper. The growth of grain boundary grooves is ideal for studying Ds in a given direction on a given surface over a range of temperatures, because the same specimen can be repolished and used again. However, there is considerable work involved in growing a symmetric bicrystal, and for a survey of Ds in two or more directions on many surface orientations, the technique would be arduous. A better technique appeared to be the scratch method used primarily by Mykura. 2 If a scratch is placed in a surface whose surface tension is independent of orientation, the surface will smooth out in time under the influence of surface tension. To determine D, from this flattening, Blakely and Mykura2 used an approximate solution which was assumed to describe the rate of flattening. Recently King and Mullins3 (hereinafter K and M) have given a more exact analysis of the flattening of an isolated scratch. A second aim of this paper was to check the validity of this newer analysis and compare the values of Ds determined thereby with the values obtained from grain boundary grooving techniques. EXPERIMENTAL PROCEDURE In an effort to work with a particular predetermined surface orientation, light orthogonal scratches

Jan 1, 1963

By N. K. Chen, C. H. Mathewson

Single crystals of high purity aluminum of various orientations were carefully documented after plastic extension. Special attention was given to the formation of slip lines, deformation bands, and asterism. An explanation for the geometry and mechanism of formation of deformation bands is considered. WHILE the general process of plastic extension of face-centered cubic metals is well understood,&apos; the accompanying structural changes due to slip and rotation are far more complex than ordinarily assumed. In the case of stretched single crystals of aluminum, the complicated behavior is especially marked by the formation of deformation bands, as first indicated by Collins and Mathewson." Such bands were believed by them and also by others,".&apos;7 who have discussed banded structure in general, to represent one of the important modes of lattice reorientation and to be intimately connected with the recrystallization process. Yet, despite their fundamental importance to the understanding of the mechanism df both plastic deformation and recrystallization, practically no study of the crystallographic features of these bands in their relationship to the conventional slip process has been attempted. This paper describes part of an extensive investigation on the structural behavior during plastic deformation of aluminum single crystals and is especially concerned with the characteristics of deformation bands. The investigation of the subsequent re-crystallization of deformed aluminum single crystals will be discussed in a later publication. Experimental Procedure Single crystal specimens of 99.996+ pct pure aluminum, Yz in. in diam and 5 to 6 in. in length were made both by the Bridgman method5 nd by a modified temperature gradient method.&apos;* Crystals were selected in which the lineage deviation did not exceed 2"; i.e., as determined from the back-reflection Laue X-ray photograms. These crystals were radiographed to insure that no internal porosity was present. The orientations showed good coverage of the whole area of the Taylor and Elam triangle.&apos; Orientations of the crystals were obtained by the back-reflection Laue technique described by Greninger." Crystals so selected were tapered very carefully in a lathe to obtain a linear decrease in diameter from 0.500 to 0.350 in. along a gage length of 3 in. This is considered desirable because it permits a strain gradient to be introduced in a single specimen at one initial orientation. The advantages of tapered crystals for studying the development of slip lines and recrystallized grains have been pointed out by previous investigators." The cold-worked layer resulting from the machining operation was removed by alternate etching in aqua regia and careful polishing with 2/0 emery paper until undistorted Laue back-reflection spots were obtained. A homogenization treatment at 600 °C for 24 hr was then introduced to insure the removal of residual stress. Two of the crystals so prepared were also checked by use of a glancing angle technique. Using a copper target, at 30 kv and 10 microamperes, a monochromatic beam was positioned at right angles to the axis of the crystal about which it rotated. The time of exposure was 24 hr. From these X-ray photograms, it was concluded that the present method of preparation of single crystals is satisfactory. Following this procedure, the crystals were elec-trolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. Intermittent

Jan 1, 1952

By R. J. Stokes

This paper compares the room-temperature mechanical behavior of magnesium oxide crystals containing &apos;fresh&apos; and &apos;grown in&apos; sources. &apos;Fresh&apos; dislocation sources introduced by cleavage or mechanical contact move and multiply to generate slip bands at 3000 psi. Macroscopically the crystals yield smoothly at 6000 psi and can be quite ductile. When &apos;fresh&apos; sources are eliminated by chemical polishing the crystals have to rely on &apos;grown in&apos; sources to initiate slip. They then deform elastically up to extremely high stresses (-30 to 50,000 psi) yielding with a sharp stress drop down to the level at which Ifresh&apos; sources operate. Grown in&apos; sources are considered to be associated with impurity wecipitate particles or inclusions. Annealing crystals at 2000°C dissolves these particles thereby eliminating sources for slip. The crystals then become consistently stronger (> 70,000 psi) approaching within 1/10 of the theoretical strength. Dislocations of the grown-in network do not move under stress to nucleate slip. It is proposed that they are locked electrostatically. DISLOCATIONS were originally conceived to resolve the large discrepency between the theoretical and real strength of solids. The idea that slip propagates by the movement of dislocations is now well confirmed both by electron transmission and etch pit studies. But this by itself is not sufficient to explain the low yield strength of crystals for there is still the need to understand where slip dislocations originally come from. Theoretical estimates place the stress to generate dislocations homogeneously in the lattice at approximately 1/30 of the shear modulus,&apos; a value 104 to 105 times greater than the stress at which the very first manifestations of plastic deformation have been observed. Only an special cases can the theoretical strength be approached; in crystals of high perfection such as whiskers2 where dislocation sources do not preexist and in covalent crystals where the dislocations present at room temperature are almost completely immobilized by the bond character of the solid.3,4 For the most part it is necessary to assume that the yield strength of ionic and metallic solids corresponds to the motivation and multiplication of dislocation sources present beforehand. The question as to their origin appeared to be answered by the suggestion of Frank and Read5 that dislocations forming part of the grown-in structure could operate as a mill for the large scale production of dislocations. The Frank-Read mechanism is still widely accepted as the source of dislocations but a number of observations have been reported which are in serious disagreement with it. One of the most intriguing of these is that under normal testing conditions dislocations of the grown-in network appear to play no role in the plastic deformation of rock salt structure ionic solids. This was first reported in the etch pit studies on lithium fluoride by Gilman and Johnston6 and is true also for magnesium oxide. To explain the comparatively low yield stress of lithium fluoride it was proposed by a number of authors7,9 that small unresolved prismatic loops formed by vacancy condensation were acting either directly or indirectly as the dislocation sources. This proposal led Gilman10 to perform a series of detailed and careful experiments on lithium fluoride to try to identify the sources responsible for the initiation of slip. He concluded that prismatic loops played no general role and that other sources were more important. Dislocation sources in ionic crystals can be divided into two general categories. First, there

Jan 1, 1962

By Paul A. Flinn, Jean-Marie Robert Genin

The MCssbauer effect was used to study the distribution of carbon in Fe-C alloys of high carbon content during room-temperature aging. In freshly formed rnartensite the carbon distribution is approximately random; carbon clustering occurs dun&apos;ng aging. In the retained austete the carbon atoms are isolated, suggesting an efiective repulsion; and no rearrangement during room-temperature aging is evident. The kinetics of the carbon clustering in martensite has been studied in detail at 0" . 10". and 20°C. The time and temperature dependence observed is sinzilar to that reported for a variety of other aging effects, such as resistance change, hardness increase, and recovery of internal friction. The stabilization of the martensite kransformation also appears to be related to the clustering effect. DESPITE extensive efforts since the early days of Reaumur, the mechanism which provides the strengthening of steel remains controversial in many cases for several reasons: 1) The structure of as-quenched martensite is not well-determined. 2) Experimental methods capable of distinguishing between various hardening mechanisms are not well-developed. 3) The temperature of formation of many low-alloy martensites is so high that the martensite formed during quenching may be already tempered to some extent before any observation. Among all the hardening phenomena, the most puzzling one occurs at room temperature, where no structural changes have been detected by the usual methods of X-ray diffraction or electron microscopy. However, a new and more sensitive technique became available with the discovery of the MBssbauer effect. This effect makes possible the detection of changes in the local environment of iron atoms in solid solution. It has been extensively used in the study of substitutional alloy systems, for example, Fe-Al,1 Fe-Si,2,3 Fe-Rh,4 and Fe-Ni.5 Making use of the possibility of obtaining new structural information, we undertook an investigation of the aging of high-carbon Fe-C martensite to follow the structural changes involved in the aging at room temperature. Preliminary results6 showed that a clustering of the carbon atoms occurs with time. A systematic study of the kinetics of the process showed a striking similarity to the kinetics of stabilization of the marten-sitic transformation, thus suggesting further investigation of the relationship. EXPERIMENTAL TECHNIQUE To eliminate difficulties with the aging of martensite prior to the first experimental measurements, we needed an alloy with an M, temperature not above room temperature. Other investigators7 were misled by results obtained on alloys which transformed above room temperature and underwent structural changes prior to the first Mossbauer measurements. Winchell and cohen8 dealt with this difficulty by using a third element, nickel, to depress the MS below room temperature. The presence of nickel did not seriously interfere with hardness or resistivity measurements, but it would complicate the interpretation of the Mossbauer data by increasing the variety of iron environments. We chose, therefore, to obtain the necessary lowering of the M, simply by increasing the carbon content. After the first quench to room temperature, our specimens are retained austenite, which we later quench into liquid nitrogen. The martensitic transformation takes place suddenly, so that the as-quenched condition of the samples is retained, since the temperature is low enough to prevent any carbon diffusion. A Massbauer spectrum at 77°K can be taken and analyzed; after an appropriate up-quenching to the aging temperature, a new Mossbauer measurement at 77°K can be made. Fig. 1 shows a typical cycle of experiments. The samples were foils 25 p thick of high-purity

Jan 1, 1969

By Hsun Hu

Direct observations were made on the recrystalli-zntion of a cold-rolled (110) [001] crystal of 3 pct Si-Fe by annealing thin sections of the specimen inside the electron microscope during examination. Subgrain formation, presumably by polygonization, occurs rapidly, followed by a slow increase in the subgrain size before recrystallization can be detected. No migration of the subgrain boundaries was observed, and the formation of recrystallization nuclei by coalescence of subgrains is suggested. Re-c~ystallization characteristics of various texture components were individually examined. AS reported in a previous paper: orientations of the various deformation texture components in a 70 pct cold-rolled (110) [0011 crystal of 3 pct Si-Fe were completely confirmed by transmission electron diffraction patterns taken at various areas of the specimen. These orientations can be summarized as follows: Over most areas of the deformed crystal (111) planes are parallel to the surface. These areas correspond to either $- the two main defor: mation textures, the (111) [112] or the (111) [112].2-5 Within a few areas, (100) planes parallel to the surface are frequently found. These areas represent the minor deformation texture component, the (100) [Oll] type, which is derived from rotated Neumann bands.2&apos;4&apos;5 Only in very rare instances are (110) planes found parallel to the surface. This orientation corresponds to the very weak texture component of the (110) [001] type. In a pole figure, this (110) [0011 orientation is located within the orientation spread between the two main (111) [1121 type textures. Usually the electron diffraction patterns taken at various areas of the specimen are very simple ones, i.e., for any one area the pattern consists only of sharply defined spots of a single orientation. In some areas, however, more or less continuous rings of weaker intensities are superimposed on a simple pattern, indicating the presence of a wide range of additional orientations. In order to understand in detail the recrystallization of this cold-worked crystal, the recrywtallization characteristics of each of the various deformation texture components must be examined. This can best be done by using a high-temperature stage and transmission electron microscopy techniques, whereby small areas corresponding to the various texture components can be selected individually for examination. The present paper presents results obtained by this method. MATERIAL AND METHOD Specimens were prepared from a previously studied1 single crystal of a commercial grade 3 pct Si-Fe alloy with an initial orientation (110) [00l], cold-rolled 70 pct from 0.014 in. to 0.004 in. in thickness. Thin foils were prepared by electrolytic polishing as described in the earlier paper.&apos; Specimens of this thin foil were then mounted in a high temperature stage similar to the one designed by Whelan.6 A direct current was used as the heating source. The temperature of the heating grid was calibrated by means of a Pt vs Pt-10 pct Rh thermocouple in a vacuum chamber (0.01 to 0.02µHg). Maximum variation within the temperature range of 250o to 000°C was about ± 25°C. After the desired areas were selected for examination, the specimen was heated to a low temperature for some time while the selected area was constantly watched. When no further change in structure and orientation could be observed, a higher temperature was applied. Photomicrographs and diffraction patterns were taken from time to time during examination, with the heater temporarily turned off* while the photographs were

Jan 1, 1962

By N. J. Grant, C. Stein

A more complete determination of the chromium-rich portion of the Cr-Ni phase diagram was made, based in part on resistivity measurements. The existence of a eutectoid reaction at 1215°C,made,based in addition to the previously reported eutectic reaction at 1343°C, was confirmed. Metallographic studies, lineal analysis, and diffusion-couple evidence were utilized to support Metallographicand extend the findings of the resistivity measurements. Delineation of the a chromium solvus line shows that the maximum solubility of nickel in a chromium decreases rapidly from 25 wt pct Ni at the eutectoid temperature to 16 wt pct. Ni at 950°C. IN recent years alloys of high chromium and nickel content have become of more interest as better performance of metals at higher temperatures is sought. It has become increasingly important, therefore, that the Cr-Ni binary diagram, which is composed of two of the elements commonly found in many high temperature alloys, be known more accurately. In particular, the chromium-rich portion of this diagram has for a long time remained incompletely determined and has been reported in the literature with a great deal of conflicting evidence. In general, electrolytic chromium of nominal purity was used by most of the earlier workers, who, except for Jenkins et al., made no further attempt to purify the metal. In the present redetermination of the chromium-rich portion of the Cr-Ni phase diagram, every effort was made to use the purest component metals available and to retain this purity throughout the preparation of the alloys and their subsequent handling. Early work by Voss, Bain," and Phebus and Blake4 indicated that the Ni-Cr binary diagram was a simple eutectic system with rather extensive terminal solid solutions. Later, Nishigori and Hamasumi," Tasaki, Weaver and Jellinghaus,&apos; Matsunaga, and Jette, Nordstrom, Queneau, and Foote attempted to determine the limits of the phase fields. Except for Jette and coworkers, the other investigators agreed that the temperature of the eutectic reaction occurred between 1320" and 1340°C and at a composition of 50 or 51 pct Cr. There was, however, considerable disagreement as to the melting point of the chromium-rich alloys and the limits of the solid-solution fields. As a result of the studies of Jenkins et al., the liquidus and solidus curves up to 80 and 90 pct Cr, respectively, were outlined. In addition, the solid-solution phase fields at higher temperatures had been investigated and showed only two phases. The boundary of the chromium-rich a phase was not determined precisely according to these authors, but indications were that it tended to confirm the earlier work of Nishigori and Hamasumi. A more recent investigation by Taylor and Floyd,&apos;" using X-ray methods, essentially corroborated the diagrams proposed by Jenkins et al., and by Wise and Eash (see Fig. 1). Again, no indication of a third phase in the chromium-rich portion of the diagram appeared. The earlier observations, however, are not substantiated by the modifications to the Ni-Cr binary diagram proposed by Bloom and Grant." In the investigation carried out by Bloom and Grant, X-ray methods showed that an eutectoid reaction existed at approximately 1180°C, in addition to the eutectic reaction at 1343°C (see Fig. 1). Their determination of the melting point of pure chromium was 1930°C (later revised to 1903"C)." Experimental Procedure and Results The chromium used for this study was electrolytic chromium, made available by the United States

Jan 1, 1956