Search Documents

By L. G. Huntley

Discussion of the paper of L. G. HUNTLEY,. presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 102, June, 1915, pp. 1333 to 1349. E. W. SHAW, Washington, D. C. (communication to the Secretary*). -The comparatively great extent and uniform character of the Dakota sandstone make it of great interest to the student of rock pores and the movements of their fluid contents. However, compared with other sands in areas of carbonaceous rocks facts concerning it do not seem to be of such great direct importance to the producer for it has thus far yielded few important pools of oil or gas. Information concerning the sandstone is extensive but scattered, hence a general treatise regarding it-particularly its pores, the fluids they contain, and the movements of the fluids-has been much needed. I therefore feel that the. chief thing to be ,desired concerning Mr. Huntley's paper is that it were more extended, particularly as to the discussion of the data presented. The general structure map of the Dakota is of especial interest. Slight changes in wording seem to be desirable here and there in the paper. For example, at the beginning of the third paragraph one-wonders if flora instead of fauna were not intended. In Figs. 2, 3, 4, and 5 the vertical scale seems incorrect. Concerning the analyses of oil quoted it is noted that they "are given, as indicating what may be expected in different localities." This seems to need modification for the average analysis of oil from Powder River, which indicates for example that this oil begins to boil at 213°C. The fact is that the samples to which this figure refers were taken from seeps long exposed. to the air :find hence the underground Dakota oil of this district no doubt differs profoundly from that which the analysis indicates. The product of a well here would probably differ more in boiling point and other. respects from the samples analyzed than it would from almost any other petroleum in the world. The use of the word synclinorium does not conform to the original definition, but this may be pardonable because misuse of the term, though a different misuse, has become general. Synclinorium is an orographic term and cannot be correctly applied outside of mountain regions, for it is derived in part from the Greek word for mountain. It has, however, been widely used in a purely structural sense for compound syncline. The broad shallow syncline of the Dakota sandstone falls in neither category. Objection might also be made to the use of

Jan 12, 1915

By T. Sterry Hunt

IT is now five years Since I called the attention of the Institute to the industrial importance of the coal and the iron ores of the Hocking Valley in Southeastern Ohio, and in a pamphlet on the region published Soon after, in 1874, endeavored to resume the principal facts then known respecting it, including the observations of the geological survey of Ohio, made and published up to the time by Professors Andrews and Wormley, together with an estimate of the probable future of the region, and its relations to the coal and iron markets of the country. Since that time the labors of the Geological Survey have included a further Study of the coal by Prof. Edward Orton, the results of which will be awaited with much interest. I may say from my knowledge of them, that while confirming the general conclusions of his predecessors, he has been enabled to add much to our knowledge as regards the correlation of the various members in different parts of the coal-field, and to Show more clearly the positions and the importance of the ore-beds in the Hocking Valley region. The only ore mined in that vicinity previous to 1874, was below what is called the Great Vein or No. VI coal, and to the west of what is known as the Hocking Valley coal-field, and although experiments in a few furnaces in the State had Shown that this coal could be used with advantage in iron-Smelting there was not a single blast furnace within the field. My observations at that time, however, impressed me with the abundance of iron ore, not only below but above this important coal Seam, and I then ventured to express the opinion that this region, from its cheap and easily mined Smelting-coal, its native ores and limestones, and its geographical position and relations to the great markets of the West, and to the supply of rich iron-ores from Lake Superior, was destined at no distant time to become a great metallurgical centre, where iron could be made more cheaply than at any other equally accessible point in the country. The object of the present communication is to report progress, and to State how far my observations made in the region last month have justified the predictions of 1874. The five years which have elapsed have been, as all know, most unfavorable to the iron trade, and especially to new enterprises in untried regions, yet they have not passed without important industrial developments in the Hocking Valley, where not less than thirteen blast furnaces have been erected

Jan 1, 1879

By W. P. Ward

I desire ho put on record a fact in relation to the effect of man ganese on pig iron which I have never seen in print, and which may, perhaps, not have been observed by anyone except myself. In 1875, while experimenting on the production of ferroman ganese in a blast furnace, I had burdened the furnace with a charge which I calculated would produce a 15-per cent. spiegel. The fur nace was very hot, having been running for a couple of days on a very light burden, and making a burnt iron, preparatory to the experiment I proposed to make to produce a high grade of spiegel. I calculated that the charge would begin to work in the fur nace in about twelve hoars after it was put on. After the -lapse of that time I commenced to watch the furnace carefully, but found little or no change in the appearance of the metal, although there was a very decided change in the cinder, showing that the man ganese ore had come in work. The iron was quite gray and very tough. The character of the cinder was good for a spiegel cinder, and 1 could not imagine where the manganese was going to, as it (lid not appear to be in either metal or cinder in anything like the quan tity indicated by the charge. The next morning things were still in the same condition. The furnace was very hot, the cinder good, and the iron very gray. I was then sorely puzzled. I had never heard of a gray iron with over 4 or 6 per cent. of manganese, and had no notion that an iron with more manganese could be gray and tough. With great difficulty a piece for chemical test was broken from a pig. Not less than a hundred blows from a heavy sledge were required to break it off, I took the specimen to the shop and directed that some borings from it should be brought to the laboratory, as soon as possible, whither I myself at once repaired to put things in readi ness for a rapid manganese determination. In about half an hour the machinist came in with the iron specimen in one hand and about a dozen blunted and broken steel drills in the other, saying that it mas impossible to drill the iron. There were several little depressions in the iron, which was malleable enough to be indented by the point of the drill, but not a chip had been cut from it. The metal was never subjected to further physical tests. A chip broken from

Jan 1, 1882

By E. D. Gardner

When the National Forests were created, all lands embraced in their boundaries were exempted from all forms of entry, except mineral claims. Later, by Act of June 11, 1906, and as amended by Act of Aug. 10, 1912, provision was made allowing homesteads on areas chiefly valuable for agriculture and not necessary for the public use. Patents to mining claims in the Forests are granted the same as on land not in the Forests, irrespective of timber or other values. It is the policy to encourage the highest use of the Forests. As a business proposition, it is a good policy to have mines developed in the Forests. Their development in remote or inaccessible regions causes the country to be opened up and, in addition to the local market which the mines create, means of transportation are afforded to outside markets. No examination of mining claims is made until patent has been applied for, unless they are actively interfering with the administration of the Forest. In this case, an examination is made, and if there is evidence that the claims are being held in good faith they are in no way interfered with. Timber is never sold from a mining claim except with the consent of the claimant, or unless it is clearly shown, after an examination, that the claim is abandoned. In the case of fire-killed timber, which rapidly deteriorates by standing, a contract bond arrangement can be made for the sale of the timber which protects the interests of both the mining claimant and the government. The promiscuous locating of mining claims has in the past caused considerable trouble. It has been, and still is, the custom in some parts of the West to locate a mining claim when the surface rights of any particular area are desired, irrespective of the mineral character of the ground. This has been done to hold power sites, town sites, summer residences, springs, etc. When the ground is desired for any of these purposes, what is known as a Special Use Permit will be issued at a nominal sum, to legalize the occupancy. In most instances, it is far cheaper to take out one of these permits than to do the annual assessment work on a mining claim, but, of course, patent to the ground cannot be obtained in this manner. If mineral were discovered on the land covered by a Special Use Permit, it would ordinarily be the policy to cancel the permit if it were clearly

Jan 1, 1915

By Ernest R. Darby

WHEN bronze is melted in open-flame furnaces a considerable amount of slag is formed during the melting operation. This slag maybe incidental to the melting practice or it may be formed intentionally by slag-forming constituents added to the furnace charge to provide a covering for the melted metal. When this slag is removed from the furnace, it contains, in addition to the free metal carried with it by the skimming operation, a considerable amount of metal as oxide either combined or mechanically mixed with it. By the usual crushing and washing methods this metallic oxide generally goes to the tailings pile, so diluted by other foundry waste that its recovery is economically impossible. If this furnace slag is not mixed with other foundry waste, practically all of the metal oxide as well as the free metal may be recovered by some form of smelting operation. The first side of the problem to be considered is the amount of slag produced. It may not be true that the majority of foundries have no record of the amount of slag made, but it is certainly true that a very great many either have no record or pay little attention to it. Usually the collection of furnace slag for one normal week's run will be sufficient to determine the advisability of its being handled in a different manner from the crushing and concentrating generally employed. If a large representative sample of the accumulation is crushed and concentrated and the recovery compared with the results of a careful assay, it will be found that a large percentage of the total metal content was lost in the washing process. The percentage of loss will be greater than the metallic oxide content, as some free metal in extremely fine particles always is carried away in grains of slag. From such a comparison, it may be determined whether or not the slag should be melted, sold or treated as before. An example of an actual test of this kind is given below. In a foundry melting 50,000 to 80,000 lb. of bronze per day, a week's accumulation of furnace slag and ladle skimmings amounted to 16,500 lb.-over three times as much as the foundry superintendent estimated before the accumulation was made. Two tons of this material was taken as representative of the lot. This was ground through a thoroughly cleaned ball-mill and concentrated over a Wilfley table. The

Jan 1, 1928

By Henry N. Toler

Development in the Jackson gas field, Hinds and Rankin counties, for 1935 continued at a slow pace, there being only nine wells drilled on the structure, of which five resulted in gas producers and four in dry holes. There were no wells drilled deep enough during 1935 to test any of the horizons below the producing Selma chalk. There are 113 producing gas wells in the Jackson gas field, with three wells on the southeast edge of the field making some oil with a large quantity of salt water; this oil comes from the same horizon as the gas. The combined open flow of the 113 gas wells is about 4,100,000,000 cu. ft. The proven area of the field is approximately 8000 acres. The production of 10,291,000,000 cu. ft. for 1935 represents the largest yearly pull from the field by almost a billion cubic feet. The total production from the field to date is 45,104,000,-000 cu. ft. It is interesting to note that the rock pressure has dropped from 1010 lb. per sq. in. initial to 943 Ib. at the end of 1935, a decline of only 67 lb. in 6 years. There is a difference of opinion as to the age of the deepest formation tested on the Jackson structure; some people holding that it is Tuscaloosa, others, Trinity, and still others that it is Paleozoic, probably Pottsville. The production of the Amory gas field, Monroe County, continued to decline and the capacity was far under the demand. Originally there were four producing wells in the field with a combined open-flow capacity of approximately 15,000,000 cu. ft. and a rock pressure of 680 lb. per sq. in. At the end of 1935 only two wells were producing with a combined open-flow of less than 1 million cu. ft. and the rock pressure down to 100 lb. or less. No attempt has been made to drill new wells in the immediate field but three wells are being drilled in the county in an effort to secure new supplies of gas. The wildcat operations for 1935, with only 11 wells drilled, were the lowest since 1932, just about one-half the number drilled during 1934. None of the wildcat wells drilled in 1935 resulted in producers and, so far as the writer is aware, did not uncover any large structures. The 11 wells drilled were abandoned or junked at comparatively shallow depths, except the well drilled in George County to 6928 ft. by the United Gas

Jan 1, 1936

By W. P. Blake

FORGING under the hydraulic press, which was introduced by Haswell in the year 1861, at the machine shops of the Imperial State Railway Company of Austria, has since been greatly improved, so that at the present time there are very few parts of machines which cannot be produced in this way, and at no greater cost than iron castings. The process is now used at Vienna chiefly for such parts of locomotives as cross-heads, link-bars, axle-box frames, etc., especially where the form is intricate, and there are many angles and projections. These objects weigh from 50 to 150 lb. or more, and it is claimed for them that they are not only much cheaper than ordinary forgings, but are much more regular in form and stronger. The results which Mr. Haswell has attained, after years of patient experimenting, were well shown in the Austrian Department of the Vienna Exhibition by a collection of the pressed objects in iron and steel, just as they left the moulds, with some of them cut asunder longitudinally and the surfaces etched, so as to show the internal structure or direction of the grain. Through the courtesy of Mr. Haswell and his son I saw the hydraulic presses in full operation at the works, drawing down large Bessemer ingots, cutting them up into blocks of convenient size, and forming various parts of locomotives. They have two large hydraulic presses in use; the largest, with a piston 24 inches diameter, gives 1200 tons pressure, and the second, with an 18-inch piston, gives 600 tons pressure. The pressure in the pumps is 600 atmospheres. The action is vertical ; the piston descends upon the work, and for forging ingots is armed with a hammer-like head. An ingot of No. 7 soft Bessemer steel, which was forged in my presence, weighed 2030 lbs. One end being placed upon the anvil, the piston is brought slowly down and crowded into the mass as if it were putty or dough, forcing it each way, but chiefly in the direction of the length of the ingot, this being the narrowest section of the anvil and hammer. The piston is then raised and the ingot is moved forward for a second squeeze, and so on, until the first half of the ingot has been reduced in thickness, when it is turned on edge and the operation is repeated. The ingot is then turned end for end and forged until the whole length has been re-

Jan 1, 1874

By J. P. Dovel

HAVING been requested to prepare a paper referring especially to my patents as applied to blast furnaces, I shall confine my discussion to those improvements and inventions pertaining directly to the blast furnace itself, omitting a number of patents pertaining to blast furnace operations. I spent the early part of my life in the construction of blast furnaces, from rivet-heating to drafting and designing, much of the work relating to repairs and rebuilding. Later, as I became more interested in maintenance and operation of a group of blast furnaces, one fact especially made a lasting impression on me, namely that a very expensive piece of equipment was very short lived, and the expense of replacement, relining, etc., in many instances consumed most of the profits made while in actual operation. As far back as 1910, I began to lay plans to build with a view to permanency and not merely for a blast, the common expression at that time, which really meant only one or two years in southern practice. Since we did not then blow so hard most failures occurred in the bosh and hearth. The failure of either generally meant a complete new lining, as the inwall did not look good enough to last another blast. At that time we were using two types of hearth, one of heavy steel plate protected by well and sprays on the outside, and .one of heavy. cast iron, made in sections and bound together with wrought-iron bands. The former type proved dangerous, for if the iron should come through, as it frequently did, it would cut away the steel plate, quickly turning large quantities of molten iron into the water, causing a severe explosion and costly repairs. The cast-iron type gave trouble also by the iron finding its way through the joints between the sections, which was' not so serious; since the iron would not cut away the heavy cast-iron sections very quickly, and generally caused only small damage, and repairs-were easily made. Both types have been improved; the former by the introduction of cast-iron -water-cooled plates, placed on the, inside of the steel, jacket. This has proved to be very good construction, but has no real claim to permanency: As the cast-iron plates cannot be replaced from the outside, therefore the operator must assume that some time, at no late date, he must replace them from the inside, which will mean a blowing out of the furnace. The heavy cast-iron hearth has been improved by making the

Jan 1, 1928

By M. G. Cheney

THE production record of the Sinclair-Moren pool, in southeast Young County, Texas, demonstrates that under efficient operating methods a single well may obtain normal oil recovery from an area of 100 acres or more. This record is the more surprising in view of relatively adverse reservoir conditions such as lack of water drive, moderate initial reservoir pressures and a consolidated sandstone reservoir with original permeability greatly reduced by processes of lithification. This case history is considered worthy of special study in view of the ever present problem of proper spacing of wells. Cupidity, abetted by the unrestrained law of capture, has in too many instances guided development and production methods without regard for sound economic and engineering principles. Largely as a result of ill advised spacing of wells, many oil fields have brought financial losses instead of deserved profit to those using capital, time and energy in this important business of adequately meeting the petroleum requirements of what is known as our modern civilization. In March 1923, the Sinclair Oil and Gas Co. obtained initial daily production of about 12,000,000 cu. ft. of gas and 1100 bbl. of oil in its first well near the center of a 372-acre lease on the L. P. Moren land, James Rose survey, Abstract 245. This exploratory test was drilled as a geological prospect of average promise, on a plunging anticline with possibly 10 ft. of closure as mapped on the outcropping limestone of upper Canyon (Pennsylvanian) age. In subsurface, the top of the producing res-ervoir is 16 ft. lower in this well than in the highest wells but probably 25 ft. above lowest closing contour. Wells No. 2 and 3 were drilled about 1/4 mile west and southwest near a normal fault with some 30 ft. of downthrow to the southwest. The producing sand was reached at a depth of 2512 ft. and drilled to 2529 ft. in the first well. This sandstone reservoir is of Millsap Lake (middle Strawn, upper Cherokee) age. It was absent in the second and third wells, which were abandoned at the depths of 3725 or more. In April 1925, a fourth well was drilled 600 ft. east and 24 ft. lower for top of sand than No. I. Production of about 100 bbl. daily was reported from 2521 to 2562 after an 80-quart shot. This well was drilled to 4560 ft., plugged back to 2575 and shot again; but was abandoned soon thereafter because of small production.

Jan 1, 1940

By Klaus Schwerdtfeger, Leo Zwell

The equilibrium between Ir-Fe or Rh-Fe alloys, iron oxide (wüstite or magnetite), and CO2-CO atmospheres has been determined at 1200°C. The data are used to derive the activities in these binary solid solutions. Both systems show negative deviations from Raoult's law. The lattice parameters are given for the investigated Ir-Fe and Rh-Fe alloys. IRIDIUM and iron form a continuous series of fcc solid solutions at elevated temperatures.' Rhodium-rich Rh- Fe alloys have fcc structure.' In the medium concentration range an ordered bcc phase is stable at temperatures up to about 1300°C. Phase relations in iron-rich alloys are not well-known. No thermody-namic data are available for these alloys. EXPERIMENTAL METHOD The experimental method used was to measure the equilibria between a gas phase of known CO2/C0 ratio, the alloy, and iron oxide (wüstite or magnetite). In one series of experiments the alloys of known composition were heated in CO 2-CO gas mixtures. After treatment (usually 1 day) the sample was quenched to room temperature and its surface examined visually to determine whether an oxide tarnish had formed. The procedure was repeated at slightly higher CO 2/CO ratios until the CO 2/CO ratio of incipient oxidation was found. Subsequently, the CO 2/C0 ratio was lowered again in small increments until the tarnish was reduced. In other experiments mixtures of alloy and iron oxide powders were pressed into pellets and equilibrated with the CO2-CO gas phase. In order to ensure that equilibrium was attained, two specimens with different starting iron content were heated side by side; in most cases, equilibrium was approached in one pellet by reduction of iron oxide and in the other pellet by oxidation of metallic iron. The sample was quenched to room temperature, and the composition of the equilibrated alloy was determined by X-ray measurements of lattice parameters and comparison of these values with calibration curves obtained from alloys of known composition. The oxides present in the specimens were identified by comparison of their diffraction patterns with those in the ASTM Card File. It may be expected from the noble character of iridium and rhodium that no appreciable amount of iridium or rhodium is dissolved in wiistite and magnetite under the present experimental conditions. The activity of iron in the alloy is then equal to that established in the iron oxide by the COrCO atmosphere. The activities of iron in wüstite and magnetite, as a function of oxygen pressure, were taken from the work of Darken and Gurry,

Jan 1, 1969

By Pol Duwez, Paul Pietrokowsky

The crystal structure of the compound TisGeS has been determined from X-ray powder diffraction data. Related silicon and tin compounds have been found to be isomorphous. Unit cell dimensions, axial ratios, and parameters for equivalent atomic positions are given. THERE is, at present, only meager information pertaining to the solid state reactions of titanium with the elements in group 4B of the periodic table (silicon, germanium, tin, and lead). The only two compounds whose crystal structure has been established are TiSi² and TiGe² (references 1 and 2 respectively). These two compounds are isomor-phous and have an orthorhombic symmetry D242h— Fddd. The titanium-rich regions of the constitution diagrams of titanium-silicon, titanium-tin, and titanium-lead have been investigated by Craighead et al.³ While valuable information concerning the alpha solid solubility of these three elements in titanium was obtained, no light was shed on the existence or nature of the titanium-rich compound in these systems. The present study is concerned with the crystal structure of the intermediate phases Ti5Si ?, Ti³Ge³, and Ti5Sn³, which were found to be isostructural. The alloys were prepared by mixing the pure metal powders in the desired proportions, pressing the mixture into pellets, and melting them in an electric arc furnace in the presence of a helium atmosphere.& After melting, the specimens, weighing approximately 5 g, were sealed in evacuated quartz vials, homogenized at 1038°C for three days, and quenched from that temperature. Powder diffraction patterns were made with a 143.2 mm diam Debye-Scherrer X-ray camera in which the Ievins and Straumanis film arrangement was utilized. Filtered copper radiation was used throughout the entire investigation. A study of the powder patterns of a series of alloys of various compositions indicated the presence of a compound around a composition corresponding approximately to a ratio of 3 titanium to 2 silicon, germanium, or tin. From a visual examination of the diffraction patterns, it was evident that the silicon and germanium alloys were iso- morphous. For small angle reflections, the powder pattern of the tin compound was analogous to that of the silicon and germanium compounds, but after the first ten reflections, the similarity was no longer clear. The powder pattern of the germanium compound was selected for indexing, since it exhibited a weak small angle reflection and clearly resolved doublets in the back-reflection range. Good agreement between observed and calculated values of (1/d)² was found by indexing the pattern on the basis of hexagonal symmetry. For the hexagonal system:

Jan 1, 1952

By H. Fechtig, R. H. Buck, A. G. Guy

MULTIPHASE diffusion has been studied for many years in two-component systems1,2 and many of the experimental aspects are now fairly well understood.314 Although by no means all of the problems connected with the two-component case have been solved,' attention has recently been directed to the more complex situation involving three components. The pioneer work of Clark and Rhines6 yielded a qualitative picture of the types of behavior that can occur, and Clark7 has suggested conventions for describing the various phenomena. Kirkaldy and co-workers8,9 have made quantitative studies in several ternary systems and have offered explanations of the occurrence of isolated and nonisolated precipitates. At present, however, there is no comprehensive theory for the variety of phenomena observed in ternary, multiphase diffusion. By analogy with several studies that have been made of multiphase diffusion in the binary Cu-Zn system,2'10'11 a similar exploratory study was made of Cu-Zn-Ni alloys lying along the line in the ternary diagram from the point 80 Cu-20 Ni to the zinc corner of the diagram, Fig. 1. A principal question to be answered was whether initially plane interfaces would remain plane during the course of one-dimensional diffusion. The diffusion specimens studied are described in Table I. The five separate alloys from which they were made were melted in evacuated Vycor capsules from 99.9 pct purity copper, zinc, and nickel. Since some of the alloys were too brittle to be swaged, all of the alloys were used in the cast condition. To facilitate later homogenization, the molten alloys were solidified by plunging the capsule in water. Homogenization heat treatment was done at 720°C for 20 hr. The five nominal compositions in weight percent zinc and nickel, respectively, were: 37.5, 12.5; 44.0, 11.2; 50.0, 10.0; 55.0, 9.0; 65.0, 7.0. Ln Table I the alloys are identified only by their zinc content. Sandwich-type diffusion specimens were prepared by pressure welding disk specimens, each about 3 mm high by 10 mm in diameter. Welding was done in a special threaded vise which was heated at 500°C for about an hour in an atmosphere of flowing hydrogen. A measurement of the separation of the phase interfaces was made on a polished flat on the welded specimen, and then the specimen was sealed in an evacuated capsule and given the diffusion treatment shown in Table I. The diffused specimen was sectioned longitudinally

Jan 1, 1965

Silver ore was first discovered in 1866 at Manhattan, and a few ore shipments were treated in a mill at nearby Belmont. The district was abandoned from 1869 to April 1, 1905, when rich gold float was discovered on what was to be called the April Fool claim. By early 1906, 4, 000 people lived in Manhattan. The San Francisco earthquake, in April of 1906, caused the withdrawal of capital from Manhattan and most of the mines were shut down. Later that year and in 1907, however, more strikes were made. The camp prospered until the mid-1920s, but a steady production of several hundred thousand dollars per year was sustained even during the great depression. Then, in 1939, Nevada's first bucket-line dredge was installed below the town and operated until 1947, producing $4.6 million in gold. The Houston International Minerals operation at Manhattan was started in July of 1980 at a throughput of about 545 mt per day (600 st per day). In contrast to the early day underground operations, Houston's mine is open-pit and processes low-grade disseminated ores. The ore is a metamorphic schist containing 2. 7 g Au and 1. 03 g Ag per mt (0. 08 oz Au and 0. 03 oz Ag per st). Some coarse gold, up to 1 mm in size, is present. Mining and haulage is done by a contractor. Stockpiled mine-run ore is crushed in three stages comprising a jaw crusher and two cone crushers, with screens ahead of the cone crushers. Crushed product, at about 19 mm (3/4 in.) size, is stored in a silo. Grinding is by single stage ball mill with the discharge passing over two hydraulic traps for coarse gold removal. These traps will be replaced in late 1980 by a two-cell Pan American jig treating the cyclone underflow. The jig hutch product, along with the hydraulic trap product that has been stored, will be treated further for gold recovery. The gravity tails will then be cycloned with the underflow being recirculated in the ball mill and the overflow being treated by flotation. A rougher concentrate is made in twelve No. 48 Galigher cells with the float tails being cycloned. Cyclone underflow is refloated in another four No. 48 cells; the overflow is treated in sluice boxes for further gold recovery before being sent by gravity to the tailings pond. Bulk flotation concentrates are cleaned three times with the final concentrate being thickened. The thickener underflow is then batch cyanided in mechanically agitated tanks and washed with barren liquor

Jan 1, 1981

By W. H. HOWARD

Discussion of the paper of W. H. HOWARD, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin No. 92, August, 1914, pp. 2029 to 2046. EDGAR M. DUNN, Anaconda, Mont.-Mr. Howard's contribution to the literature on the Cottrell, method. of electrostatic precipitation of flue dust and fume at Garfield has been read by us with peculiar interest for the reason that we have been experimenting with the same process at Anaconda for the past eight or nine months, with a view to adapting it, under the direction of Dr. Cottrell and the supervision of J. 0. Elton. and D. R. Kellogg, representing the Anaconda Smelter Commission, to the treatment of very large volumes of gases, using large pipe treaters and various forms of electrodes, with about 150,000 volts rectified current. For the amount of gas to be treated here the 5-in. pipe means a cost for installation that is practically prohibitive, clue to the tremendous number of pipes required, and we have been trying to cut installation costs by increasing the size of the pipes. All of our work is still in the experimental stage, but we have obtained good clearance on our mixed roaster and converter gases with a 3-ft. pipe treater 20 ft. long, and with 5 ft. velocity therein; and with a discharge electrode of a single No. 29 nichrome wire set in the middle of the 3-ft. pipe, with. a consequent electrode spacing of 18 in. The current used has been 150,000 to -160,000 volts, .and of course there have been troubles galore, relating particularly to insulation and rectifying. Blast-furnace gases did not give so good clearance, probably due to relative poverty in moisture and S03 content of blast gases to roaster-converter gases; making the blast gases the poorer in conductivity. Our experience has been so satisfactory that in our next experimental plant-built on a somewhat larger scale-we shall attempt a 4-ft. treater with greater electrode spacing, and a somewhat higher voltage-up to 220,000. As to fractional precipitation, mentioned by Mr. Howard, this idea was tried out at Anaconda last year (1913). Formerly our furnaces (Bruntons) roasting flue dust for the recovery of white arsenic, passed so great an, amount of dust to the settling kitchens that refining of this arsenical product was necessary to eliminate the 5 to 20 per cent. dust contained therein. Consequently the manufacture of As203 was effected in two stages, with a reverberatory roast of the first .product to obtain the final 99.5 per cent. As203. -

Jan 11, 1914

By T. E. Ockershauser

The Southwest Antioch Oil Field located in T2&3N - R2&3W, Garvin County, Okla., was discovered in February, 1946, by The Globe Oil & Refining Co. and The Vickers Petroleum Co. at their Melinda Gibson No. 1. Oil production was encountered at a depth of 6,525 ft in 14 ft of lower Pennsyl-vanian sandstone. The producing sand, locally called the ."Gibson" or "Third Deese," is a sand bar deposit strung along the west flank of the Pauls Valley uplift in a northwest-southeast direction. The oil reservoir is defined to the east by the edge of sand deposition along the uplift and to the west by the gradation of sand into shale. Within the Antioch Unit, the sand dips from 150 to 400 ft per mile southwesterly and has a pay thickness varying from 10 to 55 ft and averaging 28 ft. Several areas of Gibson production have been developed, including the Katie pool on the south, the Elmore Area of the Southwest Antioch Gibson Sand pool. the Southwest Antioch Gibson Sand pool proper, the Southwest Maysville pool and the New Hope pool on the north. Production extends over a belt 22 miles long by about two miles wide and is continuous except into the Katie and New Hope pools. It appears that drilling will soon prove these intervening areas productive. To March 1, 1950, approximately 18,000 acres have been developed with 450 Gibson wells. It is likely this count will ultimately reach 32.000 acres with 800 wells. RESERVOIR The natural production of oil from the Gibson reservoir is primarily due to solution gas expansion though gravity also plays a part. There is no indication of water drive or evidence that an initial gas cap existed. Gibson oil has a stock tank gravity of 43" API and was saturated at the original reservoir pressure of 2.925 psi. It contained 1,3440 cu ft of gas per bbl in solution and had a high shrinkage of 70 per cent. Connate water amounts to 15 per cent. Reservoir temperature is 130°F. Porosity averages 15.5 per cent and permeability ranges from less than one md to over 1.000. Based on meacurement of 400 core plugs from 15 wells, 78 per cent of the permeabilities fell within the 10 to 1,000 md bracket and averaged l67. Primary oil recovery is estimated at 140 bbl per acre-ft or 22 million bbl for the present 137-tract unit. Due to unitization

Jan 1, 1951

IN order that you may be expert in every phase of this art of parting, I wish to caution you upon twelve points, all necessary, so that you may know beforehand what may happen to you and what provision you must make to obtain good results. Understand that the gain derived from this art lies in carrying out the work that you wish to do accurately and with profit, which means nothing other than working with certainty and seeing that there is no loss of gold or silver [69v] or substance of anything that is valuable in itself. For, since everything lost is silver or gold, it is valuable however little. it may be, and many little things obviously make one large one; for gain increases gain, and loss, loss. Therefore, you will have as your first task to seek to have the materials that you are to use for making the aqua fortis of as perfect a nature as possible. I tell you this because the saltpeter is often weaker and of worse quality than the alum. For this reason it is necessary to make an effort to have it not only well refined and free from earthiness but also of a nature as powerful as pig [dung] saltpeter, the color of which tends strongly toward yellow. In order to work better, you also refine this again before you put it to use, as I shall tell you in its place. Likewise, see if you can get alum of the red kind that comes from the Levant or from Cartagena, for it costs less and is more powerful. Furthermore; see that you have a good number of well-formed cucurbits of properly purified glass not too large and of, equal content and size. Above all, see that they contain, no indentations, bubbles, folds, or scratches, especially, in the, body or in the bottom, because they break easily and the nature and great force of the acid pierces them by eating away, and makes a little hole. For this reason, cucurbits. are always divided into four grades; one is taken for making aqua fortis, another for drying the waters when they are laden with silver, the third for recovering the acids from the separations, and the fourth are either rejected as useless or dangerous, or are saved for recovering the whites or for some other service. Whoever wishes to practice this art well should remember to keep a large supply of cucurbits, receivers, and alembics. The third is the precaution which one must take in luting them; first, to

Jan 1, 1942

By G. Richards Gwinn

Graphite is one .of the so-called minor nonmetals that have become of major importance during the present conflict. Requirements of the domestic industry for graphite are relatively small and uses have changed so greatly in the past 25 years that different types, with few exceptions, are more nearly interchangeable in use. However, the quality of the graphite required for crucibles is exacting and under present manufacturing practices only a small part of the world production can be utilized economically by this industry. Graphite, for the domestic crucible industry, was supplied almost entirely by imports from Madagascar and Ceylon before the present war. The quantity required has been increased by the war and the greatest demand is for Madagascar flake. The fall of France to Germany in 1941 and the Japanese expansion southward threatened our supply of crucible-grade graphite, therefore the domestic industry was revived to supplement imports and to act as insurance in the event of complete stoppage of imports. Two plants were constructed for the Government, one at Ashland, Alabama, called the Crucible Flake Graphite Co., operated by Haile Mines, Inc., and one near West Chester, Pennsylvania, operated by the Benjamin Franklin Flake Graphite Co. Loans were made by the Reconstruction Finance Corporation to the Alabama Flake Graphite Co. at Ashland, the Ceylon Graphite Co., at Goodwater, Ala., and the Southwestern Graphite Co., at Burnet, Texas. However, by the end of 1943 the import situation had improved and it was no longer necessary to continue Government assistance to mine and stock-pile the high-cost domestic material. Graphite is found in virtually every country of the world. Most occurrences are of no economic importance because of their poor quality, prohibitive mining and milling costs, inaccessibility, and poor location with reference to the industrial centers where graphite is used. The principal commercial deposits are found in Ceylon, Madagascar, Chosen (Korea), United States, U. S. S. R., Canada, Germany, and Mexico. Graphite is a typical international mineral in that it is utilized mainly in countries noted for industrial activities, whereas the two islands, Ceylon and Madagascar, which produce the major part of the world's high-grade graphite, are virtually devoid of any manufacturing establishments requiring its use. The industry thus is violently disturbed by wars. Types oF Graphite Used in Crucibles Graphite of various kinds and from many countries has been used for making crucibles. Passau (Bohemian) flake was first used in Europe, but by the middle of the seventeenth century crucible formulas were established largely on Ceylon graphite and German Klingenberg clay. Ceylon graphite is granular and the grains are subdivided into more or less

Jan 1, 1948

By Stephen Birch

LATOUCHE, or the Beatson plant of the Kennecott Copper Corpn., is located in the Prince William Sound district of Alaska about 80 miles west of Cordova and 60 miles from Seward. Ore was discovered and claims located on Latouche Island in July, 1897. The mines were worked in a desultory manner until 1910, when the property was acquired by the Kennecott Copper interests. The first shipment of ore was made in 1904; only the higher grade ore was mined and no attempt was made to treat the ore until it was taken over by the Kennecott, company. Since that time the mine has been developed to produce 1500 tons a day and a mill has been erected for treating this tonnage, using flotation entirely. The orebody is more or less lenticular in shape with a maximum width of about 280 ft. and a length of about 800 ft. The southern end of the lens is split by a horse of waste for about 400 ft. The hanging-wall limit is a well-defined fault associated with a band of pyrrhotite, having an average dip of 60°. There is no defined foot wall, the value of the ore governing the limits of the mining; in one part of the mine, however, it is defined by a minor fault. The orebody is located in a shear zone of the country rock of graywacke and slate. The principal mineral is chalcopyrite associated with pyrite and quartz. The mine is located a few hundred feet from tidewater; the mill is located on the beach and the ore is hoisted direct from the mine through a vertical shaft into the mill bins. Until the past year practically all the mining had been conducted in open pits. During the past two years, the ore above the 200-ft. level has been developed and a system of stoping devised to recover this ore; however, this system has not been in use long enough to give any definite results as to costs or efficiency. It consists, principally, of dividing the orebody into stopes, across the full width of the orebody, 70 ft. wide with a pillar 30 ft. wide between the stopes. Raises are driven through the stopes at intervals of about 60 ft. and all the ore is broken by drilling from these raises; in other words, similar to a shrinkage stope, doing the drilling from the raises instead of setting up on the broken ore as is customary. The ground is very much broken up by clay slips and seams running in every direction. Shrinkage stoping had been

Jan 1, 1924

By V. A. Zanadvoroff

THE mine and concentrator of the Howe Sound Co., Chelan Division, are at Holden, in a remote section of the Cascade Mountains of northwestern Washington. Holden is at an elevation of 3200 ft., in the narrow valley of Railroad Creek. This creek drains into Lake Chelan, at a point some 40 miles up the lake from the town of Chelan. The concentrator treats 2000 to 2500 tons of low-grade copper-gold-zinc ore per day. Concentration is achieved by the differential flotation process, with recovery of 94 per cent copper and 82 per cent gold in the copper concentrate, followed by the recovery of 65 to 70 per cent zinc in the zinc flotation circuit. The final flotation tailing is deslimed, and coarse sands, representing 60 to 70 per cent of the total, are cyanided. The tonnage of tailing material amounts to 1900 to 2370 tons per day. GENERAL CONSIDERATIONS The property is within the Chelan National Forest. Railroad Creek is a fishing stream, being stocked regularly with trout from State hatcheries. Consequently, in planning a milling operation, the Howe Sound Co. was obliged to avoid any pollution of the stream by tailing material, and also destruction of valuable stands of timber. Moreover, the selected tailing disposal sites should not mar the natural beauty of the valley. In addition to these requirements, the problem of tailing disposal at Holden was complicated by topography and climatic conditions. The valley is long and narrow, averaging 1200 to 1500 ft. in width. Its walls are flaring at a steep angle. There are no extensive flat areas suitable for deposition of tailing. All valleys tributary to Railroad Creek, also the well-marked paths of snowslides, must be avoided. Finally, the direction of prevailing winds and possible dust hazard arising therefrom dictated the necessity of selecting the tailing-disposal sites downstream from the mill building and two campsites. Heavy snowfall during the winter months of November to March, inclusive, impedes building of the retaining dike, making it necessary to prepare the needed storage space during the summer months. It is inadvisable, also, to do any dike building during the freezing weather, because the dike becomes unstable with the spring thaws, producing inevitable "sloughing" of the built-up borders. TAILING-DISPOSAL SITES The existing tailing-disposal areas are near the south wall of the valley. They were developed, and put to use in the following sequence: No. I. Area.-Covers approximately 10 acres. Built up to the height of 60 ft.

Jan 1, 1946

By F. W. McQuiston

INTRODUCTION IDARADO Mining Company's mill and surface plant are at the portal of the Treasury tunnel at elevation 10,625 ft, 12 miles south of Ouray, Colo. In 1943 and 1944 this tunnel was extended in a westerly direction to tap the Black Bear vein, and, together with the recently completed 1100-ft inclined Treasury raise, provides access to the Black Bear mine. In 1945 a 250-ton mill was placed in operation to process development ores containing much needed copper, lead and zinc for war requirements, and to serve as a pilot testing unit for larger scale milling operations. In the years 1902 to 1927 some 329,000 tons of ore were produced from mine workings on the Black Bear vein that extended downward from elevation 12,325 ft at the Black Bear tunnel portal to elevation 11,618 ft, the lowest level of the mine. The ores were taken to the Cascade and Smuggler-Union mills near Telluride over two aerial tramways. Gold bullion, a copper-lead concentrate, and a zinc concentrate were produced. ORES The Black Bear is a compound fissure vein that has undergone several stages of mineralization. The first important stage is represented by complex ores of copper, lead and zinc in a quartz gangue. Precious metal content in this stage is low. The galena is argentiferous and varying amounts of tetrahedrite, freibergite and bornite tend to increase the normal copper content represented in chalcopyrite. The zinc occurs as a true sphalerite with little or no iron. Later re-openings of the fissure took place more or less co-extensively with the successive introduction of (1) abundant quartz gangue containing minor amounts of chalcopyrite, galena and sphalerite; (2) free gold in a fluoritic quartz gangue; and (3) barren, low-grade quartz with minor amounts of pyrite as the only important sulphide. The sulphides show practically no oxidation and little mineralogic intergrowth. Because of the common overlapping of these successive stages of mineralization within a given mining area, considerable dilution of the base-metal content takes place, thus lowering the average mill-head grade. PLANT PRACTICE Metallurgical testing was started shortly after the Black Bear vein was encountered on Treasury tunnel level in 1944. Laboratory tests showed good flotability of the minerals in the ore and indicated an economic separation could be made of the copper, lead and zinc minerals into their respective concentrates. The success of the separation is close reagent control to maintain a balance between promotion and depression of the sulphides. To maintain this balance reagent consumption for the three metal separation is considerably higher than in ordinary lead-zinc flotation.

Jan 1, 1947