Search Documents

By M. W. Ditto

THe conversion of the beehive coke plants, in this country, to byproduct plants has been slow, because the coal supplies were near the centers of the steel industry. With the growth of this industry, especially with its development around Chicago, it became necessary to transport large tonnages of coal from the eastern districts and then convert it into coke. The losses due to transportation costs were partly offset by the value of the byproducts recovered. To save the transportation costs, it was desirable that the coal deposits of Indiana and Illinois be utilized. This coal had always been classified as non-coking; it was also considered unsuitable for the metallurgical field because of the high ash and sulfur contents. The conditions, however, were promising enough to start experimental and development work, which crystallized in the design of the Roberts coke oven. The fundamental features of most coke ovens, with respect to the application of heating gas and the recovery of byproducts, are the same and, in the last few years, the tendency has been toward the better application of heating to the walls, higher thermal efficiency, and, by the control of heating conditions, the increase of byproduct yields. Structural features also have been improved and the use of high-grade refractory material has allowed the use of higher temperatures with the resulting higher rated capacity per oven per day. Great improvements have been made in both recuperators and regenerators, particularly with reference to the individualizing of each oven with respect to its adjacent oven, so that each can be operated as a unit if desired. The highest development of the flue type of oven has been applying individual regenerators for the recovery of waste heat. After some research work, it was found that the high-volatile Illinois coals could be utilized for coke by obtaining the better application and control of the heating conditions in the oven. Most of this high-volatile coal that had been used gave a good coke structure under certain conditions. The fact that coke was occasionally made from this coal, demonstrated the possibiity of making coke from it at all times pro-

Jan 1, 1923

By Guillermo Zuloaga

The iron deposits of the Imataca Range of Venezuela, which occur along the Orinoco River, in the northern border of the Guayana Highlands, have lately attracted attention on account of their economic possibilities. Many deposits occur in this area; some of slight economic importance and others that may rank with the largest masses of high-grade iron ore of the world. The geology and the character of the ores seem to be remarkably similar to those of the large iron deposits of Brazil. In the investigation of the Venezuelan deposits a definite relationship has been found between the mineralization of the large orebodies and igneous intrusions, especially norites and granites. The following paper is the result of a field and laboratory investigation of the ore deposits. The field work was done during the months of February and March of the year 1929, partly in the company of Prof. W. H. Newhouse. The laboratory studies have been made in the Massachusetts Institute of Technology, under the supervision of Professor Lindgren and Professor Newhouse. GENERAL GEOLOGY OF GUAYANA HIGHLANDS General Geography and Physiography The Sierra de Imataca proper occupies a narrow belt along the south bank of the Orinoco River, in the northeastern part of the State of Bolivar and in the western part of the Delta Amacuro Territory of Venezuela. The State of Bolivar is generally known as the Venezuelan Guayana, as it forms part of the same physiographic province of the Guianas and northeast Brazil. In general the Venezuelan Guayana is an extensive plateau, sloping gently towards the Orinoco River to the north and towards the Atlantic Ocean to the east. In the northern part mountains are rare, and consist mainly of elongated low hills. Towards the British Guiana-Brazil boundary, table mountains with vertical cliffs are found forming the ranges of Parima, Roraima and Pacaraima. General Geology The Guayana Highlands are the northern extension of the Brazilian Archean shield. Only a few scattered masses of sediments remain on its

Jan 1, 1935

By Arthur Green

A GROUP of 13 cities situated in Los Angeles and Orange counties in Southern California is engaged in constructing an aqueduct to carry water from the Colorado River at a point near Parker, Arizona, to a distribution point sear Riverside, California. The aqueduct will have a total length of approximately 241 miles, and is designed to deliver 1605 cu. ft. of water per second, or a little more than one billion gallons per day. The aqueduct crosses a barren, desert waste and the project includes approximately 91 miles of 16-ft. tunnel. The large amount of tunnel driving that has been done in this country in the past few years has resulted in some remarkable developments in equipment and methods. The building of the Colorado River Aqueduct, with its 91 miles of tunnels, has called on the best engineering knowledge in the country. New and better equipment has been designed for all phases of the work, and this equipment has been coordinated and adapted to the various conditions with a high degree of efficiency. The result has been that records for tunnel driving have been set under adverse natural conditions that exceed the estimates for progress under good conditions. All of the tunnels in the main aqueduct, except the Valverde and Bernasconi at the western end, have a finished diameter, inside the concrete lining, of 16 ft. Fig. 4 shows a section of the tunnel with the concrete lining in place. Fig. 5 illustrates the finished tunnel in three typical sections. The standard tunnel grade is 3.432 ft. per mile in the 16-ft. tunnels, but the Valverde and Bernasconi tunnels have a steeper grade and a finished diameter of 15 ft. 3 in. The rough bore of the large main aqueduct tunnels averages 12.95 solid cubic yards of material per foot of advance in timbered sections and 10.76 solid cubic yards per foot in unsupported sections.

Jan 1, 1936

By H. A. Lesser, H. L. Stone, G. H. Bruce

ESSO PRODUCTION RESEARCH CO., HOUSTON, TEX. A mathematical model that represents the conduction heating of a rock formation of limited permeability is formulated. Heat is introduced by the injection of a hot condensing gas into horizontal fractures through the formation. The fractures are assumed to be equally spaced; the flow of fluid is linear. The model consists of three coupled partial differential equations and two functional relationships. Temperature histories for both fractures and formation are obtained by numerical procedures. Application of the model in predicting in situ heating of oil shale is illustrated with four sample cases. Influences of shale thermal diffusivity, fluid pressure in the fracture and fracture spacing upon heating rate are demonstrated. In all cases considered, several years were required to heat all the formation to 700F with 1,000F steam. Less than 32 per cent of the injected heat was utilized for heating the shale. To facilitate extensive calculations of this type, a set of seven dimension-less quantities are derived. With this dimensionless system, the effect of controllable parameters on economics can be explored. INTRODUCTION Vast deposits of hydrocarbons are contained in oil shale formations in the western United States and in other countries. These hydrocarbons, known as kerogen, are difficult to recover because they are immobile solids and because the rock formations in which they are found have very limited permeability. The kerogen can be converted through pyrolysis to recoverable liquids and gases if the formation temperature is elevated to the range 600 to 800F. To accomplish this heating, the formation might be artificially fractured and a hot fluid injected into the fractures. If the injection and production wells are vertical and the fractures horizontal, interwell communication will be established and the hot fluid will flow from an injection well to a production well. In this process, some of the heat in the fluid will be given up and conducted into the formation. Products of pyrolysis will flow from the heated rock matrix into the fractures and be produced, commingled with the injected fluid. The practicality of such a process is strongly influenced by the rate at which heat can be transferred from the hot fluids to the formation. An analysis of this heat conduction problem is the subject of this paper. Linear flow of a condensing gas through a set of horizontal, equally spaced fractures is considered. Temperature histories for both fractures and formation are obtained from numerical procedures. The analysis also applies to formations containing streaks of natural permeability instead of fractures. Heat flow problems similar to the one treated here have been studied by other workers. Thomas1 has solved a radial problem in which he considers the injection of a noncondensing gas into a single, horizontal fracture and approximates the temperature profile in the fracture by a step function. The solutions to other problems, which are less similar to the present problem than the one treated by Thomas, have been reviewed by Spillette.2 In addition to these mathematical studies, a field test of an in situ shale oil recovery process using hot natural gas as the injected fluid has been reported.3 The first part of this paper is concerned with the mathematical development of the problem. The differential equations, boundary conditions and functional relationships which describe the physical model are formulated and the equations are cast into finite difference form. The method of solution of the difference equations is discussed (Appendix B). The second part of this paper presents results computed for a typical oil shale formation for which steam at 1,000F is the injected fluid. Fracture spacing, horizontal and vertical thermal diffusivities

Jan 1, 1967

By S. C. Oliphant, R. Floyd Farris

Presented in this paper is a summary of the results of experiments conducted in both the laboratory and the field during the past three years in connection with casing-perfora. tion problems. Included are studies of gun features that influence bullet performance and penetration, and studies of the effect of perforator bullets on casing and the neat cement in the annulus. Discussion and data are also presented relative to the accuracy of depth measurements in deep wells. Introduction It is a common practice in the oil industry to effect the completion of oil wells by setting and cementing casing through the producing horizons and perforating the section of casing opposite the desired interval by means of a gun lowered into the well on a cable or on the tubing. This practice has been followed for some time, and this method of completion has been given considerable study by the companies that render perforating service as well as by the oil companies that utilize their services. Through continued research on this subject, it has been possible to develop guns, bullets, and powder that will permit controlled firing at great depths, and penetration of as many as two strings of casing. It is the object of this paper to present the results of studies made of gun perforating in both the field and the laboratory. These studies were made to determine the factors that affect penetration of the bullet, burring of the casing, accuracy of depth measurements, and other items. It is hoped that by presenting the results of these investigations a better understanding may be obtained of certain of the factors involved in gun perforating and further investigation of the subject will be prompted. Subsurface Tests A well approximately 9000 ft deep, which was being prepared for abandonment, was selected for subsurface tests of gun-perforating experiments, In preparing the well for the experiment, 51/2-in. casing in the hole was pulled and racked in the derrick. A test section of pipe, which consisted of 65 ft of 5-in. 18-lb J-55 casing centered inside 7-in. 28-lb N-80 casing, was placed in the derrick corner and the annulus between the two pipes was cemented from the bottom up with 161/2 lb per gal neat cement, which was mixed and displaced with a cementing truck in the usual manner. After the cement had been allowed to harden for about a week, the test section was lowered into the hole on the 51/2-in. casing to a depth of 6600 ft by casing measurements. The hole was filled with drilling fluid weighing 10 lb per gallon. A perforating company was called to perforate the pipe, but was not advised that an experiment was being conducted. The company was asked to check the total depth (to cross pins in the bottom of the test section), then to raise the gun a given distance and fire a given number of shots with 1/2-in. bullets, pick up another distance and fire a given number of 3/8-in

Jan 1, 1947

It is not often that a mining district is discovered, opened up, exploited and developed into a rich producer within the space of three or four years. Not until the year 1903 was the existence of the rich cobalt-nickel arsenides and silver of Northern Ontario even suspected by the mining public. But it is worthy of record that Dr. W. G. Miller, the man who has done so much to develop sanely and honestly the mineral resources of Ontario, pointed out [ ] the possibilities of this region at least two years before the first discovery was made. . Dr. Miller, then Professor of Geology at the School of Mining, Kingston, Ont., referred in these words to the district: "It will be seen from what has been stated on preceding pages that the district examined contains as great a variety of rocks as probably any part of the Province of equal area . . . Although few discoveries of economic minerals have been made in this territory, it may reasonably be expected that deposits of value will be found when

Jan 1, 1907

By M. W. Ditto

THe conversion of the beehive coke plants, in this country, to byproduct plants has been slow, because the coal supplies were near the centers of the steel industry. With the growth of this industry, especially with its development around Chicago, it became necessary to transport large tonnages of coal from the eastern districts and then convert it into coke. The losses due to transportation costs were partly offset by the value of the byproducts recovered. To save the transportation costs, it was desirable that the coal deposits of Indiana and Illinois be utilized. This coal had always been classified as non-coking; it was also considered unsuitable for the metallurgical field because of the high ash and sulfur contents. The conditions, however, were promising enough to start experimental and development work, which crystallized in the design of the Roberts coke oven. The fundamental features of most coke ovens, with respect to the application of heating gas and the recovery of byproducts, are the same and, in the last few years, the tendency has been toward the better application of heating to the walls, higher thermal efficiency, and, by the control of heating conditions, the increase of byproduct yields. Structural features also have been improved and the use of high-grade refractory material has allowed the use of higher temperatures with the resulting higher rated capacity per oven per day. Great improvements have been made in both recuperators and regenerators, particularly with reference to the individualizing of each oven with respect to its adjacent oven, so that each can be operated as a unit if desired. The highest development of the flue type of oven has been applying individual regenerators for the recovery of waste heat. After some research work, it was found that the high-volatile Illinois coals could be utilized for coke by obtaining the better application and control of the heating conditions in the oven. Most of this high-volatile coal that had been used gave a good coke structure under certain conditions. The fact that coke was occasionally made from this coal, demonstrated the possibiity of making coke from it at all times pro-

Jan 1, 1923

By Guillermo Zuloaga

The iron deposits of the Imataca Range of Venezuela, which occur along the Orinoco River, in the northern border of the Guayana Highlands, have lately attracted attention on account of their economic possibilities. Many deposits occur in this area; some of slight economic importance and others that may rank with the largest masses of high-grade iron ore of the world. The geology and the character of the ores seem to be remarkably similar to those of the large iron deposits of Brazil. In the investigation of the Venezuelan deposits a definite relationship has been found between the mineralization of the large orebodies and igneous intrusions, especially norites and granites. The following paper is the result of a field and laboratory investigation of the ore deposits. The field work was done during the months of February and March of the year 1929, partly in the company of Prof. W. H. Newhouse. The laboratory studies have been made in the Massachusetts Institute of Technology, under the supervision of Professor Lindgren and Professor Newhouse. GENERAL GEOLOGY OF GUAYANA HIGHLANDS General Geography and Physiography The Sierra de Imataca proper occupies a narrow belt along the south bank of the Orinoco River, in the northeastern part of the State of Bolivar and in the western part of the Delta Amacuro Territory of Venezuela. The State of Bolivar is generally known as the Venezuelan Guayana, as it forms part of the same physiographic province of the Guianas and northeast Brazil. In general the Venezuelan Guayana is an extensive plateau, sloping gently towards the Orinoco River to the north and towards the Atlantic Ocean to the east. In the northern part mountains are rare, and consist mainly of elongated low hills. Towards the British Guiana-Brazil boundary, table mountains with vertical cliffs are found forming the ranges of Parima, Roraima and Pacaraima. General Geology The Guayana Highlands are the northern extension of the Brazilian Archean shield. Only a few scattered masses of sediments remain on its

Jan 1, 1935

By C. N. J. Wagner, E. N. Aqua

The bee alloys of the terminal solid solution of rhenium in niobium were investigated by X-ray diffraclion methods. The analysis of the broadening of the powder pattern peaks from the niobium-rich alloys, cold-worked by filing, showed evidence for faulting on (211) planes. The alloys with larger rhenium concentrations were brittle, and fractured when filed. The analysis of the shapes of the diffraction profiles from powders produced by hammering with steel plates) of these brittle alloys indicated that the broadening was due predominantly to platelets bounded by clibe planes. This result was consistent with the Laue patterns from single-cleazlage facets which showed evidence for clearage fracture on {100} planes. The influence of faulting on the mechanical properties of face-centered cubic (fcc) metals and alloys, i.e., how faulting affects the various dislocation configurations in fcc metals, is well-known.' The important question is whether or not faulting occurs in body-centered cubic (bcc) metals and alloys, and, furthermore, if faulting does occur, to what extent it affects the mechanical properties. Theoretical calculations indicate that the stacking-fault energy is rather high in most bcc metals.2 The results of sev-eral studies using transmission electron microscopy have indicated that faults are present in well-annealed and lightly deformed bcc metals and alloys, such as tungsten,3 vanadium,4 and Mo-Re alloys.5,6 These faults, as have been observed, may be stabilized by the presence of interstitial (C,N,O) atom segregation to the extended dislocations. In addition, there is considerable X-ray diffraction evidence for faulting in bee metals,7-8 using the same techniques that were successful for the study of faulting in fee metals and alloys.7 This X-ray diffraction method is currently the only technique applicable for the investigation of faulting in metals with high stacking fault energies, i.e., when severe amounts of deformation are required to produce sufficient amounts of faulting to be detectable by X-rays. The thinned films of heavily deformed metals will become opaque in the electron microscope due to the high dislocation densities present. In a previous investigation of faulting8 in bee metals of group Vb and VIb, the authors observed that niobium was ductile when filed at room temperature, and showed the highest density of faults on the (112) family of planes. A niobium-base alloy system was therefore chosen to study the effect of alloying on the occurrence of faults in a bcc alloy. There is a large range of terminal solid solubility of rhenium in the alloys of the bee refractory metals. All of the Group VIb-rhenium alloys, i.e., Cr-Re, Mo-Re, and W-Re, exhibit solid solution hardening without loss of ductility.9 In fact, the ductility reaches a maximum for alloys with compositions near to the limits of solubility. This enhanced ductility has been attributed to the lowering of the stacking-fault energy in the alloy; i.e., the increased amounts of twinning provide an additional mode of deformation, resulting in the observed high ductility.' Because of this demonstrated effect of rhenium in bee alloys, it was decided to study a series of alloys of Nb-Re. Using the same X-ray diffraction methods as described in the previous investigation,' one is able to identify the possible causes of broadening of the powder pattern peaks, e.q., particle size, microstrains, stacking faults, and/or twin faults. The separation of these various contributions to the measured peak shape is accomplished by the Warren-Averbach analysis.7 I) EXPERIMENTAL PROCEDURE A series of seven bee solid solution alloys containing from 2.5 to 21.5 at. pct Re (remainder niobium) were prepared at the General Electric Research Laboratory. Buttons, weighing 25 g, were alloyed from electron-beam-melted niobium chips and random rhenium sheet by arc melting in a water-cooled copper crucible, under an argon atmosphere. The buttons were inverted and completely remelted to promote homogenization. The nominal alloy compositions are listed in Table I. Samples of the cold-worked alloys were obtained by filing to produce a powder for the X-ray study. Alloys too brittle to be filed were hammered with steel plates. The resultant filings or brittle impactings were screened through 150-mesh classifiers and compacted to the required shape for the diffractometer holder. The X-ray diffraction peaks were automatically recorded by fixed time counting at uniform 28 intervals, or by continuous registration with a ratemeter. In all cases, the (110)-(220) and (200)-(400) pairs of peaks and the (211), (310), (222), and (321) reflections were measured on a GE-XRD5 diffractometer using CuKa radiation with nickel filter or MoKct radiation and a LiF monochromator in the diffracted beam. The first part of the data reduction, completed with the aid of a series of programmed computations,10 was the analytical resolution of the Kol component of the diffraction profile. Subsequent computations were then made with reference only to the resolved Kol peak shape. These included the measurement of the

Jan 1, 1967

By W. H. Class

The embrittling effects of oxygen, ozone, nitrogen, air, and surface residues, on NaCl has been investigated. The embrittlement by ozone and oxygen was found to be associated with the formation of a NaClO3 surface compound. In these cases the initial crack that was responsible for fracture (in a bend test) always nucleated at the corners between the tension and side faces. The behavior of air was very erratic and on certain days did not produce enzbrittlement. During these periods, crystals that had become embrittled by the ozone treatment completely recovered their ductility after a short exposure to the ambient atmosphere, It was established many years ago1 that considerable ductility could be obtained in NaCl single-crystal specimens if the crystal surfaces were dissolved in water either during or immediately prior to the test. The original interpretation of this effect by Joffe attributed the enhanced ductility to the removal of surface microcracks by dissolution. Later investigations2'3 have suggested that the exclusion of air from the specimen surface is the criterion for extensive plastic flow prior to fracture. The air em-brittlement in this later work was attributed to the diffusion of gaseous atoms into the surface layers of the crystal, thereby impeding the movement of dislocations. This model satisfactorily accounts for the reembrittlement observed after further air exposure subsequent to the water dissolution treatment. However, the situation has recently become more complex by the observations in several laboratories4-t that under certain conditions air exposure does not impair the ductility of NaC1. It has also been recognized5 that improper drying operations after water dissolution can leave surface precipitates that lead to embrittlement. Cleavage defects on as-cleaved crystals can often be another source of embrittlement. In the present work the effect of the gaseous atmospheres nitrogen, argon, air, oxygen, and ozone, on the ductility of rock salt was studied extensively. The embrittlement resulting from oxygen and ozone exposures was found to be associated with the formation of a NaC1O3 surface film. It is suggested that certain atmospheres, one of which often can be ambient air, which inhibit the formation or favor the decomposition of this compound, can promote ductility. Thus one aspect of the Joffe effect is certainly related to the removal of surface compounds or complexes by water dissolution. The effect of surface precipitates that remain after drying operations and of cleavage defects were also studied. In neither of the latter cases was the embrittlement as severe as that found with a NaClO3 surface layer. PROCEDURE AND SPECIMEN PREPARATION The nature of the embrittlement produced by the agents mentioned above was studied by means of microscopy, mechanical testing, and X-ray diffraction. Specimens were cleaved from large crystals of optical quality sodium chloride obtained from the Harshaw Chemical Co., and, except for those tested in the as-cleaved condition, were given a 15- to 20-sec immersion in distilled water followed by a rinse in absolute methyl alcohol. The specimens were then blotted on a soft, absorbent paper, and dried by a few seconds exposure to a stream of warm, dry air. Such a procedure was found to give a control surface which was microscopically free of residues. (A few crystals were intentionally painted with a concentrated NaCl solution in order to investigate the effect of surface residues). All specimens were of 0.140 sq in. cross-section. Crystals prepared in the above manner were immediately placed in a gas train where they could be exposed to the desired gases for preselected periods of time. For the oxygen and nitrogen exposures, pure reagent-grade gases were employed. The ozone was provided in the form of an ozone-oxygen mixture (approximately 10 pct ozone) prepared by passing commercial grade oxygen over a strong ultraviolet light source. All gases were dried prior to their introduction into the train. Since argon was found to be completely inert in its behavior (i.e., residue-free specimens that were exposed to argon were not embrittled), it was periodically utilized to check the control specimen surfaces as well as the condition of the gas train used for aging the specimens. After exposure to the gaseous media in question, the crystals to be used for the measurement of the strain to fracture were transferred from the gas train to a protective oil bath (without further exposure to the atmosphere) where the tests were conducted in three-point bending. The apparatus was so adjusted that the load could be applied at a constant, continuous rate. Other Snecimens from the gas train were deformed

Jan 1, 1962

By Charles Austin

IN an earlier series of studies on 18-8 stainless steel at 600°, 700°, and 800°C.1 one pretreatment was used throughout; viz., 15 min. in hydrogen at 950°C., followed by an air quench. Several manufacturers of this alloy since have expressed doubt as to the suitability of the temperature employed, recommending instead the more customary Strauss treatment as promising superior results. In this subsequent investigation on the effects of the temperature of pretreatment several interesting points have arisen, which are described in this paper. Previous work on our equipment had shown a marked difference between alloys of "similar chemical composition" that had been manu-factured by different companies. Accordingly, one mill-bar length was selected from which to prepare all specimens. It could then be assumed that any marked differences in creep characteristics would be due to effects resulting from variations in the pretreatment of the alloy. The material was furnished by the Allegheny-Ludlum Steel Co. in the form of 5/16-in, dia. rod, finished by air cooling from a mill anneal at 1950°F. (1066°C.). It was analyzed only for the elements shown: carbon, 0,07 per cent; chromium, 18.73; nickel, 9.46; manganese, 0.40. Three pretreating temperatures were chosen, the specimens being held for 15 min. in hydrogen at either: (1) 1150°C., to conform to the recom-mended Strauss treatment; (2) 950°C., to compare with the results of previous tests; or (3) 750°C., to initiate precipitation of carbides in the material before testing. As the test cross sections were only 1/8 -in. dia., air cooling followed the annealing treatment. These treatments per-mitted two direct comparisons: (1) between the 1150° and 950°C. treat-ments to indicate the effect of grain size when all carbides were probably in solution at the start of the test; and (2) between the 950° and 750°C. treatments to indicate the effect of carbide "nucleation" for similar grain sizes.

Jan 1, 1940

By M. Sheffield

This paper presents a technique lor predicting the flow of oil, gas and water through a petroleum reservoir. Gravitational, viscous arid capillary lorces are considered, and all fluids are considered to be slightly compressible. Some theoretical work concerning the fluid flow in one-, two- and three-space dimensions is given along with example performance predictions in one- and two-space dimensions. INTRODUCTION Since the introduction of high speed computing equipment, one of the goals of reservoir engineering research has been to develop more accurate methods of describing fluid movement through underground reservoirs. Various mathematical methods have been developed or used by reservoir engineers to predict reservoir performance, 193-5,7,8 The work reported in this paper extends previously published work on three-phase fluid flow (1) by including a rigorous treatment of capillary forces and (2) by showing certain theoretical mathematical results proving that these equations can be approximated by certain numerical techniques and that a unique solution exists. DISCUSSION The method of predicting three-phase compressible fluid flow. in a reservoir can be summarized briefly by the following steps. 1. The reservoir, or a section of a reservoir, is characterized by a series of mesh points with varying rock and fluid properties simulated at each mesh point. 2. Three partial differential equations are written to describe the movement at any point in the reservoir of each of the three compressible fluids. All forces influencing movement are considered in the equations. 3. At each mesh point, the partial differential equations are replaced by a system of analogous difference equations. 4. A numerical technique is used to solve the resulting system of difference equations. Capillary forces have been included in two-phase flow calculations.1,4,8 The literature, however, does not contain examples of prediction techniques for three-phase flow that include capillary forces. Where capillary forces are considered, each of the three partial differential equations previously discussed has a different dependent variable, namely pressure in one of the three fluid phases. Therefore, three difference equations must be solved at each point in the reservoir. Where large systems of equations must be solved simultaneously, an engineer might question whether a unique solution to this system of equations actually exists and, if so, what numerical techniques may be used to obtain a good approximation to the solution. It is shown in the Appendix that a unique solution to the three-phase flow problem, as formulated, always exists. It is also shown that several methods may be used to obtain a good approximation to the solution. The partial differential equations and differenceequations used are shown in the Appendix. Matrix notation has been used in developing the mathematical results. Two sample problems were solved on a CDC 1604. They illustrate the type of problems that can be solved using a three-phase prediction technique. SAMPLE ONE-DIMENSIONAL RESERVOIR PERFORMANCE PREDICTION A hypothetical reservoir was studied to provide an example of a one-dimensional problem that can be solved. Of the several techniques available, the direct method of solution as shown in the Appendix was used. The reservoir section studied was a truncated, wedge-shaped section, 2,400 ft long, with a 6' dip. (A schematic is shown in Fig. 1.) This section was represented by 49 mesh points, uniformly spaced at 50-ft intervals. The upper end of the wedge was 2 ft wide, and the lower end was 6 ft wide. The section

Jan 1, 1970

By Homer Turner

THE nature and comparative features of anthracite and bituminous coals have been discussed by the writer in two previous papers.1 Although this paper is offered as a further contribution to the subject, it seems desirable at the outset to repeat some of the descriptive matter of the early works in order to show the actual connection between various constituents of both coals and the new photomicrographs and other physical and chemical properties.

Jan 1, 1929

Jan 1, 1924

By S. C. Oliphant, R. Floyd Farris

Presented in this paper is a summary of the results of experiments conducted in both the laboratory and the field during the past three years in connection with casing-perfora. tion problems. Included are studies of gun features that influence bullet performance and penetration, and studies of the effect of perforator bullets on casing and the neat cement in the annulus. Discussion and data are also presented relative to the accuracy of depth measurements in deep wells. Introduction It is a common practice in the oil industry to effect the completion of oil wells by setting and cementing casing through the producing horizons and perforating the section of casing opposite the desired interval by means of a gun lowered into the well on a cable or on the tubing. This practice has been followed for some time, and this method of completion has been given considerable study by the companies that render perforating service as well as by the oil companies that utilize their services. Through continued research on this subject, it has been possible to develop guns, bullets, and powder that will permit controlled firing at great depths, and penetration of as many as two strings of casing. It is the object of this paper to present the results of studies made of gun perforating in both the field and the laboratory. These studies were made to determine the factors that affect penetration of the bullet, burring of the casing, accuracy of depth measurements, and other items. It is hoped that by presenting the results of these investigations a better understanding may be obtained of certain of the factors involved in gun perforating and further investigation of the subject will be prompted. Subsurface Tests A well approximately 9000 ft deep, which was being prepared for abandonment, was selected for subsurface tests of gun-perforating experiments, In preparing the well for the experiment, 51/2-in. casing in the hole was pulled and racked in the derrick. A test section of pipe, which consisted of 65 ft of 5-in. 18-lb J-55 casing centered inside 7-in. 28-lb N-80 casing, was placed in the derrick corner and the annulus between the two pipes was cemented from the bottom up with 161/2 lb per gal neat cement, which was mixed and displaced with a cementing truck in the usual manner. After the cement had been allowed to harden for about a week, the test section was lowered into the hole on the 51/2-in. casing to a depth of 6600 ft by casing measurements. The hole was filled with drilling fluid weighing 10 lb per gallon. A perforating company was called to perforate the pipe, but was not advised that an experiment was being conducted. The company was asked to check the total depth (to cross pins in the bottom of the test section), then to raise the gun a given distance and fire a given number of shots with 1/2-in. bullets, pick up another distance and fire a given number of 3/8-in

Jan 1, 1947

By R. J. Wagner, F. F. Craig, H. G. Riley, J. D. Griffith

Peripheral water injection has been underway in the Sholem Alechem Fault Block "A" Unit, Stephens County, Okla., since 1955. In the engineering planning of the flood, it was recognized that maintenance of pressure in the large, dry gas caps was vitally necessary to prevent the loss of an estimated 27 million bbl of oil through saturation of the gas caps by the oil banks moving updip on the peripheral flood pattern. The development of an abundant, low-cost water supply and the rising cost of makeup-gas purchases indicated that gas-cap control by water injection was desirable from an economic standpoint, provided an eflective water barrier could be placed without premature water breakthrough into downdip oil producers. A laboratory model scaled to the existing reservoir conditions was comtructed to evaluate the feasibility of gas-cap water injection. Model studies indicated that (I) water injected at the edge of the gar-oil contact would form a continuous barrier between the oil and gas zones, and (2) water would advance uniformly downdip without segregation due to gravity effects provided a specified, minimum water-injection rate was maintained. The model test results also indicated that it was not necessary to fill the gas cap completely with water. Water injection at the edge of one of the gas caps was initiated in March, 1958, to field test gas-cap water injection. Water breakthrough occurred at a downstruc-ture producing well in April, 1959, after approximately 2.5 million bbl of water had been injected into the gas cap. This was the volume calculated to be required to form the barrier between the oil zone and gas cap. This performance indicates that prevention of oil encroachment into dry gas caps in a peripheral water flood by water injection at the gas-oil contact appears practical and that the model studies provided a valid prediction of field performance. INTRODUCTION The Sholem Alechem Fault Block "A" Sims Sand Unit was one of the fist major waterflood projects in Oklahoma to utilize a peripheral injection pattern. Design of control measures to minimize oil encroachment into the large crestal gas caps was one of the greatest single problems during engineering planning of this flood. Engineering studies indicated that saturation of the gas caps with oil displaced by the peripheral water flood could result in a loss of about 27 million bbl of oil, or over one-half the estimated waterflood recovery. This estimate was based on a residual oil saturation after water flooding of 35 per cent pore volume, compared to the negligible oil saturation initially in the gas caps. The Sholem Alechem Springer field, located in Stephens County, Okla., is an elongated anticline with structural dips varying from 400 to 1,000 ft/mile. The structure contains numerous faults, some of which are sealing. The portion of the field considered in this paper is Fault Block "A", which is the largest of the five major fault segments in the field. A map of the unit is shown on Fig. 1. The unit is bounded on the east and west by major sealing faults, on the north by a water-oil contact and to the south by a deterioration of sand development. Two domes, each having gas caps, exist in the unit and are separated by a north-south fault as shown in Fig. 1. The sands being flooded are the Sims sand members of the Springer series of early Pennsylvanian age. The Sims sands average over 100 ft in thickness in Fault Block "A" and have a porosity of approximately 19 per cent. Core permeabilities average 160 md, with interstitial water saturation of about 23 per cent pore volume. Three different zones can be correlated over most of the area. However, they are commingled in most of the producing wells. The two upper zones, designated as First and Second Sims, are the most important. Both the First and Second Sims have gas caps in the east dome, while only the First Sims has a gas cap in the west dome. These gas caps, whose limits are also shown on Fig. 1, initially occupied nearly 11 per cent of the total reservoir volume. The major concern of this paper is the control of the two gas caps in the First Sims sand. Fig. 2 is a cross section, to scale, across the east dome of this formation. Notable features are the relatively shallow dip, the deterioration of the First Sims sand on the south side of the gas cap and the water-oil contact on the northern edge. The formation dip at the gas-oil contact in this cross section is approximately 5".

By Donald C. Barton

The theory of gravitation is based on Newton's law that any two bodies exert a mutual attraction which is proportional to the product of their masses and inversely proportional to the square of the distance between them; i. e., A = KMRm2 (1) where K is a constant, M and m are the respective masses of the two bodies, and R the distance between them. In the earth's gravitational system, the earth is one of the bodies; the other may be any body within or without the earth. In theoretical discussions and calculations,in regard to gravity, that other body usually is taken as a unit of mass: in the C:. C:. S. system, a body of one gram in mass. Gravity and Level Surfaces Gravity is defined in geophysics as the force of attraction exerted by the earth, towards itself, on a body of unit mass. The intensity of gravity is usually expressed in dynes of force or in centimeters of acceleration In geophysical work in America, most commonly it is expressed in dynes (per gram) with the "per gram" understood and not directly expressed. In geophysical work in Europe, most commonly it is expressed in centimeters per second per second (cm. /sec.2) and less commonly lrierely as centimeter-gram-second units (c. g. s). At sea level, the intensity of gravity amounts very nearly to 980 dynes. The vertical is the direction along which the attraction of gravity is exerted at any point. In most cases, it is very nearly, but not quite, perpendicular to the earth's surface. The path that would be taken by a body falling freely through space toward the earth is vertical at each point and may be spoken of also as ('the vertical," or as the line of the vertical, or as a line of force of gravity. At the earth's surface it comrrlonly is very nearly, but not quite, a straight line.

Jan 1, 1929

By Wilbur T. Stuart

TO assist the mining industry in attacking problems of water control, the U. S. Geological Survey has begun a program of research in mining hydrology. In certain fundamental respects water control is similar to development of water supplies from wells or to the drainage of agricultural lands, as many of the tools developed in recent years for quantitative ground-water problems are applicable, with modification, to mine-water problems. In 1952 a 30-day pumping test conducted jointly by the Eureka Corp. Ltd. and the Defense Minerals Exploration Agency provided an opportunity to gain knowledge concerning water movements around a flooded mine shaft. The methods of analyzing the data may be used as a guide for the evaluation of similar problems elsewhere. The Fad shaft of the Eureka Corp. is on Ruby Hill, 1 1/2 miles west of Eureka, Nev. The shaft was completed at a depth of 2465 ft in November 1947 at a site adjacent to the downfaulted block in which the ore was found. As the drift on the 2250 level progressed toward the ore zone, a large flow of water was encountered after the Martin fault was intersected. This flow exceeded the installed pump capacity, and an unsuccessful attempt to recover the shaft and the 2250 level was made in 1948.1, 2 Geology and Hydrology: The complex structure of Ruby Hill is that of an anticline broken first by thrust faulting and later by normal faults. The present orebody comprises several mineralized zones within a block of the Eldorado limestone of middle Cambrian age which was downfaulted 1400 to 1600 ft, and it may be related to a similar body mined at a higher level south of the Ruby Hill fault. At the depth of the largest zone of ore the block is roughly rectangular in shape, about 1000 ft wide and 1500 ft long, and dips about 30" NE, see Fig. 1. It is apparently bounded on the south by the Ruby Hill fault, on the east by the Jackson fault, on the north by the Martin fault, and the west by the Bowman fault. Within the block, but between the Ruby Hill and the Martin faults, are the Office and Adams Hills faults; west of the block and the Bowman fault are the Albion and Spring Valley faults. There are many conflicting reports concerning the water-yielding characteristics of the Eldorado limestone and the condition of the fault zones, that is, whether they are open or tight. However, the diamond-drill records indicate that open spaces as much as 2 or 3 ft across were encountered, and considerable cementing and lining of holes was necessary to maintain circulation of drilling fluid. There is also evidence that the Eldorado limestone was cavernous where it was mined in the early days south of the Ruby Hill fault. At the site of the Fad shaft the formations encountered from the surface down included the Pogonip limestone, Dunderberg shale, Hamburg limestone, and Secret Canyon shale. These formations did not yield large quantities of water to the shaft. The Pogonip limestone, which appears to be permeable and might yield water elsewhere, is above the water table in the vicinity of the shaft. The Secret Canyon shale, immediately overlying the Eldorado in some places but in most places separated from it by the Geddes limestone,3 is apparently tight and does not transmit water. During the 30-day test period the shale briefly confined the water in the underlying formations so that artesian conditions were observed in drillholes E and F, which are cased into the Eldorado limestone, whereas unconfined conditions were observed in drillholes B, C, and D, which were open to the shale. The Geddes limestone, which normally lies between the Secret Canyon shale and the Eldorado limestone, was not encountered in the Fad shaft. The Geddes, a flaggy, fractured limestone, is reported capable of yielding large volumes of water. Water stored in the interstices of this thin-bedded limestone within the Ruby Hill fault zone on the 1200 level of the Locan shaft drowned the pumps in 1923 when the Richmond-Eureka Mining Co. attempted to explore the area along the fault. Eldorado limestone was not encountered in the Fad shaft. In the ore-block area the Eldorado limestone was not entirely offset from other water-yielding formations by movement along the Bowman fault; therefore it may be hydraulically connected with the other formations. Adjacent to the Ruby Hill, Jackson, and Martin faults, the Eldorado lies in contact with other possible water-yielding formations. One of these, the Prospect Mountain quartzite, is separated from the Eldorado by thin, sheared, and broken beds of the Geddes within the Ruby Hill fault zone. A limited examination by the author of the Prospect Mountain quartzite in the Richmond mine at a higher level and south of the Ruby Hill fault indicates that the quartzite is poorly permeable. The monzonite mass south of the quartzite would be a further barrier to the flow of water. The poor permeability of this area is substantiated by records of levels at which water was encountered south of the Ruby Hill fault. In view of the normally low rate of ground-water recharge, if this desert area had been permeable, water levels could not have been maintained at altitudes of many hundred feet above the present water table west and north of Ruby Hill. Thus the ore-bearing block of Eldorado limestone is in contact with possible water-yielding rocks on at least two sides, and if the fault zones are possible conduits for water circulation the geologic and hydrologic conditions are suitable for the infinite-aquifer type of analysis as used and modified here. History of Pumping: During sinking of the Fad shaft a maximum pumping rate of 1500 gpm kept the shaft dewatered sufficiently, but in March 1948, after the 2250 level drift passed through the Martin fault into the Eldorado limestone, the pumps and shaft were flooded. Subsequently additional pump-

Jan 1, 1956

By AIME AIME

LIFE will not be difficult for those who attend the fall meeting of the Petroleum Division at the Conoco Club, Ponca City, Okla., Sept. 30-Oct. 1. An attractive program to appeal to oil company executives and lawyers, as well as technologists, has been arranged and the Continental Oil Co. has contributed for the occasion the buildings, grounds and facilities of the club. E. 0. Bennett, Continental Oil Co., Ponca City, is chairman of the arrangements committee, and reservations for rooms and trips, requests for information, etc., should be sent to him.

Jan 1, 1932

By W. P. Sykes

SEVEN years ago, Dr. S. L. Hoyt1 presented a masterful discussion of the hard metal carbides and cemented tungsten carbide. His lecture summarized most of the data then available in the field; many of the details relating to the production, properties and structure of cemented tungsten carbide had never been previously published, for, in fact, this information was only then being acquired. During the intervening years, the cemented carbides have assumed a place of real importance in the commercial field, with an ever widening variety of applications due to constant improvement in the control of production technique and the unremitting search for new compositions that might better the performance of the alloys in one or another type of service. The most recent summary of production methods, properties and guides for the successful application of the cemented carbides appears in the 1936 edition of the Metals Handbook. Of necessity, much detailed information relating to structures and physical properties is not included in such a summary, and it is with such details that the present discussion is concerned.

Jan 1, 1938