Search Documents

By Richard Thomas Newcomb

Chapters 5a, 5b, and 6 discuss the long- run supply of minerals and the characteristics of reserve search and production peculiar to extractive industries. It is now necessary to complete the picture by examining supply and demand in commodity markets to show how mineral prices are determined and how both price and production trends might be predicted over long periods of time. These practical interests can be served best by reviewing first some of the characteristics of the short-run static market models familiar to all readers of elementary economic texts, and then extending the theory to models of a more dynamic nature. It is important at the outset to note that economic theory provides a wide variety of economic models based on varying assumptions concerning the behavior of economic agents, the properties of the goods, the time period considered, and so on. Each variety of model offers certain analytical advantages and suffers certain shortcomings. The art of the applied economist or practioner lies in knowing enough both about the technology and practice of his problem and about theory to select the appropriate models for his analysis. In our approach it will be useful first to consider the role of markets for minerals and mineral products in relation to the efficient determination of what and how goods are produced in the whole economy, i.e., a general system of markets, before getting down to the task of analyzing supply and demand conditions in specific markets. The former study is called general equilibrium analysis, while the latter is called partial. By equilibrium is meant a state of the sys- tem under study in which supply equals demand in each market, and the prices which equilibrate the quantities offered and asked are called equilibrium prices. The tendency of prices to return toward equilibrium values if temporarily displaced, or to converge to new equilibrium values if important new conditions for supply or for demand are placed, defines "stable" equilibrium systems. The short-run describes a period in which adjustments to fixed capital are not made, although variable factors such as labor or materials can be adjusted. The long-run envisions a period in which fixed capital and other such constraints can be adjusted. Thus, it may take a sharp increase in price to bring out additional supply of a factor in the short-run with existing plant, while new capacity might permit additional quantities in the long-run without an increase in supply price.

Jan 1, 1976

By Henry M. Howe

Jan 1, 1908

By P. R. Sperry, M. L. Holzworth, P. A. Beck

The basic work of Z. Jeffries 1,2,3 has long ago established the main features of grain growth in the presence of a dispersed second phase. Working with sintered specimens of initially fine grained tungsten, to which various amounts of thoria had been added, Jeffries found that grain growth was inhibited, that is, practically prevented, up to a certain annealing temperature. When this temperature, which increased with the thoria content, was exceeded, extremely large grains developed abruptly from the fine grained matrix. such a a temperature" was later found by Gross-mann~3,14 in certain types of steel, while ~~i~ showed15 that in other steels grain growth was gradual, without inhibition and abrupt coarsening. Later work demonstrated the connection between coarsening and aluminum additions. The viewpoint that the direct cause of inhibition and coarsening in aluminum killed steels is a fine dispersion of aluminum oxide21 appears to be held quite generally, although some doubts have been voiced even very recently, 20 In steels with Ti additions the titanium carbide phase is considered responsible for the inhibition effects found.20 The coarsening temperature increases with the titanium content. That coarsening may occur, as a result of, certain heat treatments, even in low carboil rimmed sheet steel, was shown by Samuels. He also detected coarsening in a steel ingot of similar composition, after giving it the same heat treatment as that used by him for the sheet material. In this instance the identity of the inhibiting phase has not been determined. However, Tangerding found23 that even the few small carbide particles, which occur in carbonyl iron, have a very marked inhibitive effect. As a result of an oxidizing anneal at 850°C, large grains begin to form at the surface of the carbonyl iron specimen, and gradually grow inward as the subsurface oxidation of the carbide particles progresses and eliminates the obstruction. The carbide particles Can be removed also by annealing in hydrogen, with similar results. But if the oxidizing anneal of 10 hr at 850°C in air is followed between in hydrogen for 75 hr at the Same temperature, grain growth is more hibition usually the whole specimen is transformed into a single crystal (approx. 1.5 cm X 5 cm). The reversed procedure, that is, hydrogen annealing followed by oxidizing annealing leads to smaller grains. Tangerding arrived at the logical conclusion that there must have been in his specimens some additional obstruction to grain growth hibition from a minor impurity, other than carbon. It seems likely that this obstruction was caused by an oxide formed during the oxidizing anneal and gradually reduced rtain the subsequent hydrogen-annealing. Other instances of grain growth inhibition of varying severity, associated with a dispersed second phase, have been described by several authors. Notable examples: lead with 0.06 pet Cu or Ni,24 cartridge brass with 0.12 pct Cr,25 or with up to 0.15

Jan 1, 1949

By A. N. Winsor

Increased use of private aircraft in civil engineering, mining, forestry, and other land-use activities creates an opportunity for amateur aerial photography. Taking a photograph having less than 5° tilt requires precision equipment and skilled personnel, while controlled horizontal photography is primarily a terrestrial method that has passed to the limbo of forgotten things. But the remaining possibility – oblique aerial photography – can be…

Jan 2, 1955

LINN BRADLEY, H.' D. EGBERT and W. W. STRONG (communication to the Secretary*).--In the discussion of the paper, a request was made for a further explanation of the curves given on Chart I. In preparing the curves given on this chart, a typical blast-furnace top gas having the following composition by weight was assumed: Per Cent. C02 21.00 CO 24.00 Hz 0.25 CH4 0:25 N2 54.50 For any given top-gas temperature, Curves A, B, C, D, and E indicate in British thermal units the sensible heat lost in cooling the top gas to 60° F. by wet-cleaning methods. Top-gas temperatures are plotted as abscissae, sensible heats above 60° F. in British thermal units are plotted as ordinates, and separate curves are drawn for top gases carrying various amounts of moisture. For any given stove exit-gas temperature, curves A1,-B1, C1, D1, and E1, indicate in British thermal units the sensible heat carried out of the stoves by the moisture which is left in the top gas when it is dry-cleaned and enters the stoves hot. This moisture is removed when the gases are wet-cleaned and the sensible heat which it carries out of the stoves is therefore saved. As before, separate curves are drawn for top gases carrying various amounts of moisture. The curves in Fig. 1, therefore, indicate graphically how much more sensible heat is conserved by cleaning the top gases by the dry-hot method than is conserved by cleaning the top. gases by a cold-wet method and thus removing the greater part of the moisture carried by them. They also show of how little moment it is from a heat conservation standpoint whether or not the moisture carried by the top gases is removed before they enter the stoves. That wet cleaning secures the removal of this moisture and is thus to be recommended from a heat conservation standpoint is an argument often advanced by advocates of wet cleaning. The curves of Fig. 1 show how fallacious such an argument is.

Jan 6, 1917

By W. C. Winegard, C. Elbaum, T. Ojala

NONOCTAHEDRAL slip was observed in poly- crystalline aggregates of aluminum by Boas and Ogilvie.&apos; These authors indicate that the non-octahedral slip takes place on (100) or (110) planes. Ogilvie2 studied the continuity of slip lines across grain boundaries in polycrystalline aluminum. Non-octahedral slip was observed by him, but it was not reported to occur in the continuous slip lines across the grain boundaries, which were identified as octahedral slip in all cases. The present note reports the observation of non-octahedral slip in the grain boundary region of an aluminum bicrystal and tricrystal, both deformed in tension at room temperature. An analysis is made, which leads to a probable identification of the non-octahedral slip planes as (110) and (331). The specimens used were of rectangular cross section, approximately 5x10x200 mm. They were prepared by growth from the melt, using aluminum reported by the manufacturer to be 99.994 pct pure. The grain boundaries were in a plane perpendicular to the wider face and parallel to the long dimension of the specimens. The axis of tension was also parallel to the long dimension of the specimen. The orientations of the specimens studied were determined by the Laue back-reflection method and are given in Fig. 1. The nonoctahedral slip was first observed after about 6 pct extension in the bicrystal, and after about 2 pct extension in the tricrystal. The micrograph, Fig. 2, of the grain boundary region of the bicrystal shows two active slip planes throughout each of the two crystals, with a third plane active at the grain boundary in each crystal. Two major sets of slip traces observed in grain No. 1 are consistent with the operation of the slip systems (ill) [oil] and (111) [011]. The nonoctahedral slip takes place on a plane belonging to a <111> zone, as determined by drawing trace normals. Assuming that slip will take place only in the <110> direction, the planes in the <111> zone, which do not contain that direction, need not be considered. Among the remaining prominent planes of that zone, the (011) plane has a common slip direction—the [011]—with the (111) plane, which acts as one of the octahedral slip planes. In grain No. 2, a similar situation to that in grain No. 1 is observed. As indicated previously, the (oil) plane in the <111> zone, to which the nonoctahedral slip plane belongs, has a common [Oil] slip direction with the acting (ill) slip plane. Also, the orientation of the (oil) plane in grain No. 2 almost coincides with the orientation of the acting (111) slip plane in grain No. 1. Similarly, the orientation of the (oil) plane in grain No. 1 almost coincides with the orientation of the acting (111) slip plane in grain No. 2. It is, therefore, possible that the nonoctahedral slip was induced, in both cases, by octahedral slip in the neighboring grain. It is important

Jan 1, 1957

By Ernest N. Patty, Sherwin F. Kelly

The present case history deals with the examination of an almost forgotten nickel prospect, near Winesap, Chelan County, Washington. Although the final results yielded no ore body of commercial importance, the integration of surface and underground exploration, geophysical survey and diamond drilling endow the story with interest. The program is significant because it is illustrative of how the most disappointing expenditures in mining exploration, the "not-finding" costs, could have been reduced had geophysical methods been applied at an appropriate stage in the prospecting work. The Chelan nickel deposit was discovered about 1900, on a sage-brush-covered hillside with a southerly slope, adjacent to Winesap Canyon; the paved highway now extending from Wenatchee northward, up the Columbia River and into Okanogan Valley, is only a mile away. After the deposit was found, three short prospect tunnels were driven into it, and the prospect then remained dormant for 40 years. No. x tunnel was 80 ft. long, running north into the hillside. For the first 35 ft. this adit exposed a typical, iron-stained gossan with streaks and stains of malachite, and small seams of water-soluble nickel sulphate. Beyond this, it encountered a relatively fresh peridotite, well mineralized with blebs of pentlandite. Systematic sampling yielded an average assay of 1.5 per cent nickel and 0.3 per cent copper. Down the hillside to the south and 35 ft. lower in elevation, No. 2 tunnel was driven under No. I and in the same direction, traversing 50 ft. of gneiss before it reached the peridotite. At this point the latter formation showed only scattered blebs of sulphides, not of commercial grade. To the west, on the same contour line as No. I tunnel, and 800 ft. around the hillside from it, No. 3 tunnel was driven 50 ft. into the hill to explore a strong gossan outcrop that assayed 0.5 per cent nickel (Fig. I). From the geological exposures on the hillside and in the tunnels, it appears that the main mass of the hill is formed of an ancient and altered gneiss complex. Into this, a sill-like injection of amphibolite (altered peridotite) was intruded, which, at least in some places, contains commercial quantities of nickel sulphide. Its structure is obscure, but it appears to dip into the hill at an angle of about 15°. In the vicinity of No. 3 tunnel a large dike of quartz diorite cuts the peridotite or amphibolite; about 140 ft. north of the portal of the tunnel, a dike of andesite 00 ft. wide cuts boldly up the hillside to break the continuity of the peridotite in that direction. The geological evidence available was not adequate to decide whether the peridotite forms a continuous sill, or occurs as isolated bodies in the gneiss. Not all of this peridotite carries commercial amounts of pentlandite, but if the mineral-

Jan 1, 1946

By Ernest N. Patty, Sherwin F. Kelly

The present case history deals with the examination of an almost forgotten nickel prospect, near Winesap, Chelan County, Washington. Although the final results yielded no ore body of commercial importance, the integration of surface and underground exploration, geophysical survey and diamond drilling endow the story with interest. The program is significant because it is illustrative of how the most disappointing expenditures in mining exploration, the "not-finding" costs, could have been reduced had geophysical methods been applied at an appropriate stage in the prospecting work. The Chelan nickel deposit was discovered about 1900, on a sage-brush-covered hillside with a southerly slope, adjacent to Winesap Canyon; the paved highway now extending from Wenatchee northward, up the Columbia River and into Okanogan Valley, is only a mile away. After the deposit was found, three short prospect tunnels were driven into it, and the prospect then remained dormant for 40 years. No. x tunnel was 80 ft. long, running north into the hillside. For the first 35 ft. this adit exposed a typical, iron-stained gossan with streaks and stains of malachite, and small seams of water-soluble nickel sulphate. Beyond this, it encountered a relatively fresh peridotite, well mineralized with blebs of pentlandite. Systematic sampling yielded an average assay of 1.5 per cent nickel and 0.3 per cent copper. Down the hillside to the south and 35 ft. lower in elevation, No. 2 tunnel was driven under No. I and in the same direction, traversing 50 ft. of gneiss before it reached the peridotite. At this point the latter formation showed only scattered blebs of sulphides, not of commercial grade. To the west, on the same contour line as No. I tunnel, and 800 ft. around the hillside from it, No. 3 tunnel was driven 50 ft. into the hill to explore a strong gossan outcrop that assayed 0.5 per cent nickel (Fig. I). From the geological exposures on the hillside and in the tunnels, it appears that the main mass of the hill is formed of an ancient and altered gneiss complex. Into this, a sill-like injection of amphibolite (altered peridotite) was intruded, which, at least in some places, contains commercial quantities of nickel sulphide. Its structure is obscure, but it appears to dip into the hill at an angle of about 15°. In the vicinity of No. 3 tunnel a large dike of quartz diorite cuts the peridotite or amphibolite; about 140 ft. north of the portal of the tunnel, a dike of andesite 00 ft. wide cuts boldly up the hillside to break the continuity of the peridotite in that direction. The geological evidence available was not adequate to decide whether the peridotite forms a continuous sill, or occurs as isolated bodies in the gneiss. Not all of this peridotite carries commercial amounts of pentlandite, but if the mineral-

Jan 1, 1946

By J. T. Lapsley, I. I. Cornet, A. E. Flanigan, R. Hultgren, J. E. Dorn

WITH the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that procedures of heat treating common magnesium casting alloys be investigated systematically. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. Research on the solution heat treatment and aging of magnesium alloy AZ92, (formerly ASTM No. 17; also known as Dowmetal C or AM260) which was done under "Restricted" Project NRC-21, in 1942-1943, and reported, in detail in a final report to the OSRD on September 3, 1943, is the basis of this paper, which has been released for publication by the OSRD. American experience with magnesium alloys prior to World War II was limited, although some of these alloys had been in commercial use since 1909. Requirements of the aircraft industry for light alloys made it imperative to understand and utilize the advantageous strength-weight properties of magnesium castings. Magnesium casting alloys are commonly solution heat treated to increase their ultimate tensile strength and ductility; this treatment may be followed by an age hardening at elevated temperatures, which raises the tensile yield strength but diminishes the ductility. In the present investigation, AZ92 was studied to determine the effects on properties of various solution heat treatment and aging schedules. The principles of heat treatment of magnesium alloys are the same as for other non-ferrous alloys. The alloy studied, AZ92, has a nominal composition of 9 pct aluminum, 2 pct zinc, and minor constituents. Fig I shows, by the projection of isothermal sections on the concentration plane, the solubility surface1 of the ternary magnesium-rich solid solutions as determined by X ray analysis. From this figure it may be seen that above approximately 375°C (707°F), AZ92 alloy is a single phase alloy at equilibrium; below this temperature the equilibrium condition is a. two phase alloy. The beta constituent which precipitates from the solid solution exerts a hardening effect. Because the zinc concentration is only 2 pct, and because of its solubility relations, AZ92 resembles a binary alloy of magnesium with aluminum. The solubility curve1 of Fig 2 shows how rapidly the solubility of the beta phase decreases with decreasing temperatures. Unlike many aluminum alloys, magnesium alloys do not age harden at room temperatures; precipitation hardening of AZ92 alloy is performed at about 177°C (350°F). At this temperature about 3 pct aluminum

Jan 1, 1947

By Walter Lawson

THE first plans were made in 1930 for the mining by open-pit methods of the low-grade disseminated ore body now known as the Morenci open pit. It was not until 1937, however, that final plans were completed and the decision reached to go ahead with the actual development. Many advances were made in open-pit mining equipment during that period of seven years, therefore the ways and means of attack actually used were very different from those originally contemplated. Diesel-operated bulldozers, big trucks, full-revolving electric shovels and electric churn drills constitute the major equipment finally purchased for this modern stripping operation. Neither the bulldozers nor the big trucks were considered in the early operating plans, for at that time bulldozers had not, been used in mining operations and the trucks as yet were undesigned. The full-revolving shovel and the churn drills were not new developments in open-pit equipment, but both had undergone remarkable manufacturing transition, emerging far more efficient and far more dependable than their predecessors. Even the ordinary drilling steel had been fundamentally changed. It was now threaded so that the dulled cutting bits could be detached and replaced, thus eliminating the costly transportation of long bars to the drill shop for resharpening. The decision to use trucks in the preliminary stripping operations was based on the desirability of this type of transportation to economi-cally prepare the pit for rail haulage, coupled with the success that the contractors had had with them on other big excavation jobs. There are at present no plans for the use of trucks beyond the preliminary work, inasmuch as rail haulage will give lower costs after roadbeds and benches are once established.

Jan 1, 1938

By R.J. Anderson

Roughly, a crack in a casting may be considered, for the moment, to be due to fracture of the alloy resulting from the stress set up by the contraction in volume on passing from the liquid to the solid state. Cracks may be external or surface, internal or deep-seated, or incipient or so-called strain cracks. Draws may appear as depressions, unevenness, and "pinching in" of the surface of a casting. Roughly, draws are due to contraction in volume and are governed largely by the same factors as cracks. A casting may be cracked, however, without being drawn. Shrinkage is a foundry term and refers to the contractio~l in volume of a metal or alloy on passing from the liquid to the solid state. Patternmaker&apos;s shrinkage is the total contraction in volume (including liquid, solidification, and solid shrinkage) that occurs when an alloy is poured into a mold. The contraction in volume of aluminum is one of the principal factors affecting the occurrence of cracks, as will be shown later, and the question of shrinkage and its control requires careful study in any treatment of cracking in castings. In the case of sand and die castings, cracks have been attributed to a number of causes, but in the case of most light aluminum alloys, they are due to the large contraction in volume on freezing and the lack of its regulation or control. The most important factors are: (1) Contraction in volume; (2) composition of alloy; (3) quality of melting charge; (4) design of casting; (5) method of molding; (6) hardness of ramming; (7) method of gating; (8) hardness and characteristics of cores; (9) chills; (10) risers; (11) melting temperatures; (12) furnace used for melting; (13) pouring temperatures; (14) inclusions in alloys; (15) hot shortness of alloys; and (16) physical properties of alloys at high temperatures. Of these, the first, second, third, and eleventh to sixteenth involve ascertainable metallurgical facts; the remainder are largely matters of opinion, judgment, and technical knowledge of men experienced in the production of castings.

Jan 1, 1923

By G. M. Schwarz

There has been considerable controversy regarding the structure and mineral constituents produced when iron ore is sintered. This investigation was undertaken in order to establish the fundamental reactions that take place in the sintering process by determining the nature of the resulting minerals. The writer&apos;s immediate interest in the subject arose mainly from the request of E. W. Davis for information based on a microscopic study of sinter submitted by him in May, 1926. In the author&apos;s preliminary work, samples of iron-ore sinter were secured from the Minnesota School of Mines Experiment Station and from commercial plants. These were polished by the usual methods for polishing opaque ores. In order to study these surfaces satisfactorily, it is necessary to magnify them rather highly, a range from 100 to 1000 dia. being used. For the higher magnifications oil-immersion lenses and an intense source of light are necessary. After the preliminary study had shown the problems involved, a series of small samples were sintered under carefully controlled conditions and with analyzed materials. Variations in the relative amounts of ore, coal and water were made in order to study the effect of each constituent. The attempt has been to arrive at a clearer understanding of the sintering process and the reactions involved without reference to any preconceived notion as to sinter. It is clear that the study of polished surfaces has yielded results not possible with thin sections alone. The thin sections made in this work were found unsatisfactory at magnification greater than 75, whereas magnifications of 1000 were easily studied with reflected light on carefully polished surfaces. A rather complete statement of observed facts is made so that the reader may form his own conclusions. The writer&apos;s interpretations are suggested. It is to be hoped that a more complete understanding of the structure arid composition of iron sinter, as well as the changes which go on during

Jan 1, 1929

By T. G. Fulmor, William Wraith

What impelled The Anaconda Company to dismantle and move a concentrator 25 miles that was already operating at a rate of 35,000 ton per day? The answer to that question takes in almost exactly 49 years and perhaps 10 complete cycles of the metallurgical wheel in the Anaconda, Mont., mill. One could say with truth that the move is a logical next-step in the development of metallurgy in The Anaconda Co. In the old concentrator at Anaconda, the background story is unfolded: - Gravity separation by jigs, later supplemented with gravity tables, 1905. - Separate sand and slime froth flotation, 1915. - Acid bulk froth flotation, 1917. - Bulk alkaline flotation, 1926. - Alkaline flotation of total ore without sand- slime separation due to change in ore type. 1939.

Jan 5, 1964

By R. J. Anderson

Roughly, a crack in a casting may be considered, for the moment, to be due to fracture of the alloy resulting from the stress set up by the contraction in volume on passing from the liquid to the solid state. Cracks may be external or surface, internal or deep-seated, or incipient or so-called strain cracks. Draws may appear as depressions, unevenness, and "pinching in" of the surface of a casting. Roughly, draws are due to contraction in volume and are governed largely by the same factors as cracks. A casting may be cracked, however, without being drawn. Shrinkage is a foundry term and refers to the contractio~l in volume of a metal or alloy on passing from the liquid to the solid state. Patternmaker&apos;s shrinkage is the total contraction in volume (including liquid, solidification, and solid shrinkage) that occurs when an alloy is poured into a mold. The contraction in volume of aluminum is one of the principal factors affecting the occurrence of cracks, as will be shown later, and the question of shrinkage and its control requires careful study in any treatment of cracking in castings. In the case of sand and die castings, cracks have been attributed to a number of causes, but in the case of most light aluminum alloys, they are due to the large contraction in volume on freezing and the lack of its regulation or control. The most important factors are: (1) Contraction in volume; (2) composition of alloy; (3) quality of melting charge; (4) design of casting; (5) method of molding; (6) hardness of ramming; (7) method of gating; (8) hardness and characteristics of cores; (9) chills; (10) risers; (11) melting temperatures; (12) furnace used for melting; (13) pouring temperatures; (14) inclusions in alloys; (15) hot shortness of alloys; and (16) physical properties of alloys at high temperatures. Of these, the first, second, third, and eleventh to sixteenth involve ascertainable metallurgical facts; the remainder are largely matters of opinion, judgment, and technical knowledge of men experienced in the production of castings.

Jan 1, 1923

To Americans, Alaska occupies a unique position, both geographically and historically. The only integral portion of the United States lying in the sub-Arctic and Arctic regions of the Earth, the early remoteness and climatic conditions effectively combined to impede the economic development of this area. Although Alaska has been a part of our Nation since 1867, its mining industry is still at that stage of development which characterized the West 100 years ago when miners concentrated on high-grade lodes and rich placer deposits. Since World War II, however, there has been a noticeable increase of interest in the raw materials of the North. This concern has been most noticeable in Canada, Scandinavia and Russia, but it has been, and is being shown in Alaska. To the American mining industry, the potential importance of this State can be summed up by the question, "Can Alaskan mining compete successfully with those of other states and countries?" The answer revolves about the vital factors of geography, economics, and the political turmoil of the World. These aspects are among those discussed on the following pages in a series of articles by Alaskans and non-Alaskans alike. We invite you to read "Alaska: Regional Report."

Jan 12, 1961

By W. E. C. Coxe

Many of you who are interested in the manufacture of iron and steel, have no doubt heard of the "Wheeler process for combining iron and steel." Mr. Wheeler has formed a company, styled the "Combination Trust Company," whose business is to grant licenses for the use of this patent process in producing what he calls "iron-clad steel." It has been proposed to apply it in the manufacture of car or wagon axles, also to shafting, having steel cores or centres covered with iron; to tubes of steel with an inner and outer skin of iron ; to structural purposes, such as girders and beams; bridge and tie-bolts, where the strength of the iron and the rigidity of the steel would be desirable. In answer to a request from Mr. Wheeler, permission mas accorded him to make some experiments at the rolling mill of the Philadelphia and Reading Coal and Iron Company, at Reading, Pennsylvania, with a view to manufacturing some steel-headed rails. In making this kind of a rail two difficulties are encountered. If the iron is brought to the requisite heat to weld properly, the steel is likely to be burned; if the steel is cared for, to prevent burning, the several layers of iron are not brought up to the proper welding heat. Mr. Wheeler claimed that the steel slab covered with iron which he furnished for the head of the rail could net be injured by any heat to which it might be subjected in the ordinary course of heating the rail-pile. He claimed, also, that by this method the porosity, which he thought was characteristic of all solid rails of Bessemer steel, would be overcome. Four steel slabs were furnished for this experiment, being Bessemer steel of .61 carbon, made at the Edgar Thomson Steel Works, and covered with iron in one of the Pittsburgh mills. The slabs were in section seven inches wide by three inches thick, and the iron covering was one-eighth to three-sixteenths inch thick. Each slab was placed on a pile of iron made up in the ordinary way for a rail fifty-six pounds per yard and thirty feet long. The heating was under the personal direction of Mr. Wheeler, and

Jan 1, 1879

By Franklin Allison

THE influence of cobalt and nickel on the properties of steel might be readily expected to be very similar. The two elements occupy close and somewhat unusual positions in the periodic table, their chemical behavior and compounds are so completely analogous and their various physical properties, including the ferro-magnetic characteristic, show such a remarkable correspondence, that there is no doubt of a strong resemblance existing between these two metals. However, the variety of, properties that are obtained from steel is due, largely to the fact that the element iron possesses allotropic forms. Alloying elements that affect these allotropic forms, or alter the nature of the allotropic changes, exert a profound influence on the resulting steel. In the case of nickel and cobalt, although these elements are very similar chemically and physically, it is found that they differ distinctly in their individual effects on the critical points of iron. Both nickel and cobalt form a series of homogeneous solid solutions with iron at temperatures above 1800° F. The difference in their behavior does not occur until changes begin to take place in the solid state below this temperature. An inspection of the respective thermal equilibrium diagrams at the lower temperatures makes the opposite effects of nickel and cobalt clearly evident.

Jan 3, 1927

By WALTER M. DAKE

GENERALY speaking, the bituminous coal mines of the country are being operated at a loss. To purchasers of the necessary commodity, a statement of this character may have the sound of a far fetched propagandist cry; but to the coal producer who lives in the hope of an up-turn in the almost stationary market price of his product, while inking in red his monthly operating balances, it carries the ringing sound of truth.

Jan 1, 1925

By Thomas Read

AMONG the large number of deep mines in the world there are several which do not differ much in depth. The St. John del Rey mine, in Brazil, has reached a vertical depth of 6726 ft. below the top of its shaft; miners enter it, however, through an adit which intersects the shaft 324 ft. below its top, wherefore it might be said that the mine is really only 6400 ft. deep. In the Kolar gold field of India there are a number of deep shafts, one of which reaches to a vertical depth of 6140 ft. below surface. In South Africa also there are a number of deep shafts, the Village Deep being 6100 ft. early in 1921. The City Deep, Ltd., proposes to sink to a depth of 7000 ft. but pre-sumably by the time it does so the St. John del Rey will be deeper than that, since it has been increasing in depth at an average rate of about 150 ft. per year. The deepest shaft in the United States, the Tamarack No. 5, although it is only 5308 ft. deep, actually approaches nearer to the center of the earth (4100 ft. below sea level, as against 3958 ft. , at St. John del Rey). The deepest workings in the Calumet & Hecla go down to 4600 ft. below sea level. The St. John del Rey is not only the deepest, mine in the world, but it also is worked by the oldest registered English mining company, which was organ-ized in 1830 to work a mine at a considerable dis-tance from this one. That mine proved unprofitable, and in 1837 operations were transferred to the. deposit now under discussion, where operations have been prac-tically continuous ever since.

Jan 6, 1923

By George Rice

THE subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on bumps in coal mines, and then presents suggestions arising from the writer&apos;s recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free&apos; from folding and faulting.

Jan 1, 1935