Search Documents

By G. E. McElroy

Changes in existing airway and fan-installation conditions offer the most common opportunities for effecting economical operation of mine-ventilating systems, but the largest possibilities for securing this result lie in the original design of the main airways for efficient service. Formulas, and charts for their graphical solution, are presented herewith for the determination of the elements of airways design when the conditions of service are known or may be roughly approximated. Although the analyses are made with particular reference to metal-mine airways, there is no essential difference between main airways in metal and coal mines, and the methods presented are applicable to both. Little attention is paid to designing airways for maximum economy in the ventilation of metal mines. Most of the openings used as main airways are originally designed and used for transportation and other operating purposes. Even where openings are made primarily for ventilation, the possibility of their future use for other operating purposes, or even custom alone, usually results in the selection of a size and shape similar to those of existing openings. Natural conditions, such as heavy ground, often seriously limit the size of opening that can be maintained without excessive expense; and various operating factors, such as velocity limitations on traveling roads, often dictate size requirements in excess of those required for economy in ventilation only. In metal mines the main airways are, as a rule, too small rather than too large for economic service, with the general result that the quantities in circulation are often less than the mine's proper requirements over long periods, even though excessive amounts of power are applied in an effort to remedy conditions. Increasing the area of an airway increases the cost for excavation and lining practically proportionately but at the same time affects a very rapid decrease in power requirements. The balancing of these two factors of the expense to give a minimum total yearly operating cost for ventilation is mainly a matter of proper original design of the main airways of the mine, since the large volumes handled through these parts of the system involve large power costs and thus present opportunities for effecting large savings through proper design. Many of the factors

Jan 1, 1932

By M. L. Samuels

DURING the period from 1910 to 1920, there was a lively interest in. the subject of grain growth and many papers were published, followed by interesting discussions. Questions dealing with the fundamentals of grain growth-why and how it occurs-were treated in papers by Howe,1 Jeffries,2 Sauveur,3 Chappell,4 Beilby,5 Mathewson -and Phillips,6 McAdam,7 Carpenter and Elam,8 Stead and Carpenter,9 Ruder,10 as well as others. Since that decade, much indeed has been done regarding the practical control of grain size, and it is now possible to order material having a size specified in the American Society for Testing Materials classification. Also, one hears the term "spliced boundaries" used in connection with certain tungsten lamp filaments" wherein it is important to prevent "sagging" between consecutive turns of the helix.12 This practical use of a certain knowledge as to the things that influ-ence or even control grain growth should not be taken as an indication that the subject has been thoroughly explored and that nothing more can be learned from fundamental studies. It is with this thought in mind that a report of some observations and experiments on abnormal grain growth is believed justified. Abnormal grain growth is met with in heat-treating high-carbon steels in the austenitic range,13 in the harden-ing treatments of high-speed steels,14,15 and in the low-temperature annealing of strained low-carbon steels as in sheet and wire material. Entirely aside from these instances of exaggerated grain growth, which some might consider as freakish, it is thought that abnormal growth is simply a case where the growth forces and the forces tending to prevent growth are almost, but not quite, evenly balanced. Information relative to grain-growth characteristics in general may be obtained from a study of abnormal growth conditions, which may be looked upon as vantage points. Reflection will show at once that if growth forces are great in comparison to inertia or resistance to growth, many crystals start to grow and, for that reason, none becomes very large, whereas if inertia is predominant no growth at all takes place. Under conditions in which

Jan 1, 1938

By Fred C. Bond, Walter Maxson

Since the last publication of tabulated results of grindability tests by the authors1 the total number of ball-mill tests made has more than doubled, and rod-mill tests have become increasingly important. Nearly all of the standard closed-circuit ball-mill and rod-mill tests made to date are included in the present tabulation, together with additional information not previously published. Standard Ball-mill Grindability Tests The method of conducting these closed-circuit tests has not been altered. A sample of the ore or other material is stage-crushed in rolls set at 1/16-in. opening with a 6-mesh screen until all of it has passed the screen. The combined minus 6-mesh screen undersize is mixed, sampled and screen-analyzed, and its apparent specific gravity is determined by packing and shaking in a standard container, and weighing. The apparent specific gravity ordinarily is about 60 per cent of the true specific gravity. The unit volume present in the mill .in all tests is 700 C.C. of the packed minus 6-mesh roll product, and the number of grams occupying 700 C.C. is the unit test weight. This weight is placed in the mill dry, ground for the number of revolutions estimated to be necessary, discharged, and screened mechanically in three testing sieves of the mesh size at which the test is to be conducted. The oversize, or circulating load, is weighed, sufficient fresh minus 6-mesh feed is added to bring the total weight up to that of 700 c.c., and the charge is returned to the mill for a second grinding period. All standard ball-mill tests are conducted at 250 per cent circulating load, and the number of revolutions in the mill necessary to obtain this circulating load at any grinding period is estimated from the results of the previous period. The number of net grams of screen undersize produced per revolution of the mill approaches its final equilibrium value after several grinding periods, and this is recorded as the grindability, or relative ease of grinding, of the sample. A cylindrical ball mill, 12 by 12 in. inside, with a smooth lining and rounded corners, is used with a revolution counter Under standard grinding conditions it runs at 70 r.p.m., and contains a charge of 285 iron balls weighing 20,125 grams, ranging from I½ to ¾ in. in diameter. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the capacity- to be expected from a given mill is calculated by comparing the grindability with that of a similar standard ore whose performance characteristics arc known. No satisfactory general formula for convertillg standard grindabilities into corn; rnercial power-consumption values has been

Jan 1, 1943

By Blake M. Loring

Recently the S-curves for 30 to 40 alloy steels have been pub1ished.l.2 These steels show individual characteristics, which make each additional S-curve of great interest. There are important differences in the mechanism of the transformation process, the type of transformation product, and the influence of alloying elements. Steels of the same general alloy composition may possess such variable characteristics with regard to the length of time of isothermal transformation that an S-curve for each heat of steel may be desirable. In the present work the isothermal transformation of a steel having the following composition and grain size was studied: 0.29 per cent carbon; 0.21 manganese; 0.026 phosphorus; 0.017 sulphur; 0.056 silicon; 1.45 chromium; 3.25 nickel; austenite grain size, 7. The progress of the isothermal transformation was followed by several different methods, including hardness measurements, dilatometer observations, and examinations of the microstructure. It was not expected that these methods would be in precise agreement.3 Accordingly, the changes in microstructure and hardness were given additional weight in determining the initial stage of transformation and the dilatometer measurements were relied on in estimating the completion of the process. The beginning of transformation was indicated by I per cent of transformation products and the end of transformation by about 99 per cent. The reproducibility of the various methods in the ranges of highest sensitivity was checked by several observations at each time and temperature. The steel used in this investigation was annealed for 24 hr, at 925°C. Macroetching revealed no serious segregation. The specimens for the metallographic and hardness investigations were 1¼ by ½ by ? in. Wires attached to the samples were used for handling. instead of tongs, to avoid chilling. The specimens were heated at 845°C. for ½ hr. and quenched into constant-temperature salt baths held at various temperatures from 205' to 650°C. The time required to transfer the specimens was found to be about 1½ sec., and nearly 5 sec. more was required for them to come to the temperature of the bath. After various lengths of time in the constant-temperature baths the specimens were quenched in water at 2I°C. The specimens were cut in half for the metallographic examination, to provide a surface free from decarburization. To determine the beginning and end of the transformation the percentage of transformation determined metallographically and by hardness was plotted against time. A planimeter was used in the metallographic determination. The hardness and metallographic determinations made at room temperature were confirmed reasonably well by dilatometer measurements taken during the process of transformation at the various temperatures. Two dilatometers were used to

Jan 1, 1942

By Willis R. Battles, William F. Cerini, P. H. Jones

A test for determining the plugging characteristics of an oil-well injection water has been developed. It consists in measuring changes of the filter rate of a water at constant pressure with cumulative throughput when passing the water through a medium grade sintered glass disk. Application of the test method was made to the water used in the Union Oil Company's experimental water flood of the Chapman zone in the Richfield field, Orange County, Callfornia. This water developed increasing plugging tendencies upon aging, even though the finished water from the plant filter exhibited few such characteristics. The plugging material was found to consist of calcium carbonate, ferric hydroxide, and organic substances that were presumed to be bacterial. Various method of stabilizing this water to prevent the formation of plugging material were attempted. Lowering the pH to approximately 6.4 by injecting carbon dioxide provided a moderately satisfactory means for stabilization but a better method of stabilizing this water was found to be first aging and then filtering. Introduction An experimental water-flood project was started on the Chapman zone of the Richfield field in March 1944 and has been described in a previous paper.' It consists of a single injection well drilled between old producing wells. A water-treating plant using primary alum flocculation, sedimentation and chlorination followed by secondary flocculation, sedimentation and fltration is employed to process the water before in@ion. In all of the water-treating operations, the system is open to the air, and no attempt is made to prevent the loss of carbon dioxide or absorption of oxygen by the water. The clear water is stored in a covered concrete basin and pumped through a Transite line to the suction of a high-pressure pump at the injection well' The high-pressure tubing in the well to the injection zone is cement lined. The untreated injection water is a mixture produced with the oil from the Chapman and Kraemer zones and is supplied from the disposal system. Because the injection well was relatively deep (injection zone about 3400 ft.) and would be expensive to replace, it was believed imperative to supply a nonplug-ging injection water and to develop laboratory procedures for evaluating the treated injection water with respect to its formation plugging properties. This report describes the development and application of the test procedure based on the assumption that the plugging properties could be determined by measuring the progressive decrease in flow rate of the water through a porous medium. If the quality of the injection water was good enough so that the plugging action on the porous medium was of small magnitude, it was reasoned that the tendency to impair flow in the formation would not be serious.

Jan 1, 1946

By Walter Maxson, Fred C. Bond

Since the last publication of tabulated results of grindability tests by the authors1 the total number of ball-mill tests made has more than doubled, and rod-mill tests have become increasingly important. Nearly all of the standard closed-circuit ball-mill and rod-mill tests made to date are included in the present tabulation, together with additional information not previously published. Standard Ball-mill Grindability Tests The method of conducting these closed-circuit tests has not been altered. A sample of the ore or other material is stage-crushed in rolls set at 1/16-in. opening with a 6-mesh screen until all of it has passed the screen. The combined minus 6-mesh screen undersize is mixed, sampled and screen-analyzed, and its apparent specific gravity is determined by packing and shaking in a standard container, and weighing. The apparent specific gravity ordinarily is about 60 per cent of the true specific gravity. The unit volume present in the mill .in all tests is 700 C.C. of the packed minus 6-mesh roll product, and the number of grams occupying 700 C.C. is the unit test weight. This weight is placed in the mill dry, ground for the number of revolutions estimated to be necessary, discharged, and screened mechanically in three testing sieves of the mesh size at which the test is to be conducted. The oversize, or circulating load, is weighed, sufficient fresh minus 6-mesh feed is added to bring the total weight up to that of 700 c.c., and the charge is returned to the mill for a second grinding period. All standard ball-mill tests are conducted at 250 per cent circulating load, and the number of revolutions in the mill necessary to obtain this circulating load at any grinding period is estimated from the results of the previous period. The number of net grams of screen undersize produced per revolution of the mill approaches its final equilibrium value after several grinding periods, and this is recorded as the grindability, or relative ease of grinding, of the sample. A cylindrical ball mill, 12 by 12 in. inside, with a smooth lining and rounded corners, is used with a revolution counter Under standard grinding conditions it runs at 70 r.p.m., and contains a charge of 285 iron balls weighing 20,125 grams, ranging from I½ to ¾ in. in diameter. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the capacity- to be expected from a given mill is calculated by comparing the grindability with that of a similar standard ore whose performance characteristics arc known. No satisfactory general formula for convertillg standard grindabilities into corn; rnercial power-consumption values has been

Jan 1, 1943

By L. E. Wilsey, W. G. Bearden

This paper presents results of analysis of the effect of fracturing on initial flow rates and on ultimate recoveries from low capacity oil formations. This analysis shows that even in formations of permeability as low as 0.1 md, large fracture treatments can yield oil recoveries and production rates approaching those of high permeability formations. Field production information is shown which supports the analytical work. INTRODUCTION Often hydrocarbon bearing formations are discovered which, while they are known to contain large quantities of oil, will not produce at commercially attractive rates without special well stimulation. Attempts to solve this problem led to the development of such techniques as underreaming, shooting, acidizing, and recently hydraulic fracturing. These methods of stimulation have been highly successful in many fields. All of these treatments, however, affect only the pay section near the well bore and therefore owe their success to circumventing and overcoming local permeability reduction about the well bore. It has been the belief that in treating wells to stimulate production in which there is no permeability reduction near the well, the maximum possible production rate increase would be of the order of two or fourfold. Hence, it has been concluded that fracture treatment of uniformly low capacity (permeability times thickness) formations could meet with but limited success. It is the purpose of this paper to show that the use of fracture treatments much larger than usually used can yield commercially attractive producing rates and high recoveries even in formations of permeability less than 0.1 of a md. PROCEDURE In order to illustrate the effects of fracturing, an analytical study of some hypothetical systems was made in which one factor at a time was varied to show what is important in recovering oil from fractured wells. It was assumed that a horizontal fracture of relatively high fluid-carrying capacity extended from a well bore. The presence of such a fracture will cause a marked influence on the flow pattern and pressure distribution in the formations, with the net effect being to reduce tremendously the resistance to flow into the well bore. A diagram of the resulting flow pattern and pressure distribution is illustrated in Fig. 1. Immediately after production commences, the principal flow of fluid is vertically from the formation flanking the fracture, into the fracture, and then into the well. After sufficient oil and gas have been produced to lower the pressure in the formation adjacent the fracture, oil and gas will begin to flow in a radial manner into the fracture from the formations beyond the end of the fracture. In calculating the performance under such conditions. the material balance or conservation of matter equation and equations of flow were solved simultaneously by a stepwise method of calculation. Flow rates were found by determining the pressure distribution, as illustrated

Jan 1, 1955

By Blake M. Loring

Recently the S-curves for 30 to 40 alloy steels have been pub1ished.l.2 These steels show individual characteristics, which make each additional S-curve of great interest. There are important differences in the mechanism of the transformation process, the type of transformation product, and the influence of alloying elements. Steels of the same general alloy composition may possess such variable characteristics with regard to the length of time of isothermal transformation that an S-curve for each heat of steel may be desirable. In the present work the isothermal transformation of a steel having the following composition and grain size was studied: 0.29 per cent carbon; 0.21 manganese; 0.026 phosphorus; 0.017 sulphur; 0.056 silicon; 1.45 chromium; 3.25 nickel; austenite grain size, 7. The progress of the isothermal transformation was followed by several different methods, including hardness measurements, dilatometer observations, and examinations of the microstructure. It was not expected that these methods would be in precise agreement.3 Accordingly, the changes in microstructure and hardness were given additional weight in determining the initial stage of transformation and the dilatometer measurements were relied on in estimating the completion of the process. The beginning of transformation was indicated by I per cent of transformation products and the end of transformation by about 99 per cent. The reproducibility of the various methods in the ranges of highest sensitivity was checked by several observations at each time and temperature. The steel used in this investigation was annealed for 24 hr, at 925°C. Macroetching revealed no serious segregation. The specimens for the metallographic and hardness investigations were 1¼ by ½ by ? in. Wires attached to the samples were used for handling. instead of tongs, to avoid chilling. The specimens were heated at 845°C. for ½ hr. and quenched into constant-temperature salt baths held at various temperatures from 205' to 650°C. The time required to transfer the specimens was found to be about 1½ sec., and nearly 5 sec. more was required for them to come to the temperature of the bath. After various lengths of time in the constant-temperature baths the specimens were quenched in water at 2I°C. The specimens were cut in half for the metallographic examination, to provide a surface free from decarburization. To determine the beginning and end of the transformation the percentage of transformation determined metallographically and by hardness was plotted against time. A planimeter was used in the metallographic determination. The hardness and metallographic determinations made at room temperature were confirmed reasonably well by dilatometer measurements taken during the process of transformation at the various temperatures. Two dilatometers were used to

Jan 1, 1942

By P. M. Robinson, M. B. Beaer

The heat of formation at 0°C of the intermetallic compound AgMg as a function of composition has been determined by tin-solution calorimetry. In this technique, the heat of formation is determined as the difference in the heat effects, at infinite dilution, on dissolution of the compound and a mixture of its components added alternately to liquid tin from a reference temperature, such as 0°C. The experimental technique and method of calculation have been described elsewhere.' The compound AgMg is a 0 electron compound with a CsCl structure.2 In nonstoichiometric compositions of the compound, atoms of the excess component are substituted on the AgMg lattice.3,4 The homogeneity range is approximately 43 to 52 at. pct Mg at room temperature and 38 to 65 at. pct Mg at 500Oc.2 Single-phase alloys outside the homogeneity range at room temperature can be prepared by quenching. The specimens used in this investigation contained from 39.0 to 54.8 at. pct Mg. They were made available, together with analyses, by the Research Laboratory of the General Electric Co. Metallographic examination of the quenched specimens containing 39.0 and 54.8 at. pct Mg gave no indication of the presence of a precipitated phase. The measured heats of formation are listed in Table I. In a calorimetric run, four to six additions each of a specimen and the corresponding mixture of the components were made. One or two calorimetric runs were carried out with each composition depending on the amount of samples available. The limits stated in the table represent the experimental precision and not the absolute accuracy of the measurements. Thermodynamic investigations of the compound AgMg have been made by Trzebiatowski and Terpilowski 5 and Kachi.6,7 The heats of formation at 500°C derived from the combined electromotive-force values of these investigators8 are more exothermic than the heats of formation at 0°C reported here, Fig. 1. The differences cannot be explained by the difference in temperature. This is shown by the published heat capacity of the stoichiometric compound, which obeys the Kopp-Neumann rule from 0" to 500oC.9 The heats of formation derived from equilibrium data are generally considered to be less accurate than those determined by calorimetric methods because small errors in the change of the equilibrium values with temperature have a large effect on the calculated value of the heat of formation. The heats of formation derived from the combined published electromotive-force values reach a maximum at 56.0 at. pct Mg.8 Kachi reports a maximum of -4.7 kcal per g-atom at the stoichiometric composition.7 The present results also indicate a maximum at or near the stoichio metric composition, Fig. 1.

Jan 1, 1964

By William F. Cerini, Willis R. Battles, P. H. Jones

A test for determining the plugging characteristics of an oil-well injection water has been developed. It consists in measuring changes of the filter rate of a water at constant pressure with cumulative throughput when passing the water through a medium grade sintered glass disk. Application of the test method was made to the water used in the Union Oil Company's experimental water flood of the Chapman zone in the Richfield field, Orange County, Callfornia. This water developed increasing plugging tendencies upon aging, even though the finished water from the plant filter exhibited few such characteristics. The plugging material was found to consist of calcium carbonate, ferric hydroxide, and organic substances that were presumed to be bacterial. Various method of stabilizing this water to prevent the formation of plugging material were attempted. Lowering the pH to approximately 6.4 by injecting carbon dioxide provided a moderately satisfactory means for stabilization but a better method of stabilizing this water was found to be first aging and then filtering. Introduction An experimental water-flood project was started on the Chapman zone of the Richfield field in March 1944 and has been described in a previous paper.' It consists of a single injection well drilled between old producing wells. A water-treating plant using primary alum flocculation, sedimentation and chlorination followed by secondary flocculation, sedimentation and fltration is employed to process the water before in@ion. In all of the water-treating operations, the system is open to the air, and no attempt is made to prevent the loss of carbon dioxide or absorption of oxygen by the water. The clear water is stored in a covered concrete basin and pumped through a Transite line to the suction of a high-pressure pump at the injection well' The high-pressure tubing in the well to the injection zone is cement lined. The untreated injection water is a mixture produced with the oil from the Chapman and Kraemer zones and is supplied from the disposal system. Because the injection well was relatively deep (injection zone about 3400 ft.) and would be expensive to replace, it was believed imperative to supply a nonplug-ging injection water and to develop laboratory procedures for evaluating the treated injection water with respect to its formation plugging properties. This report describes the development and application of the test procedure based on the assumption that the plugging properties could be determined by measuring the progressive decrease in flow rate of the water through a porous medium. If the quality of the injection water was good enough so that the plugging action on the porous medium was of small magnitude, it was reasoned that the tendency to impair flow in the formation would not be serious.

Jan 1, 1946

By C. V. Millikan, Herbert F. Beardmore

Declining Productivity Index, as considered herein, is a productivity index that has a substantially and consistently decreasing value when measured over a period of a few hours. If not recognized, it may be interpreted as representing an unsettled or unstable condition in a producing well. It forms the basis of a number of predictions as to future performance compared with the performance of wells in which the productivity index does not decline. The nost important of these are that: (I) the rate of oil production will decline more rapidly, (2) the gas-oil ratio will usually increase abnormally, (3) the amount of water ultimately produced will be negligible, if any, (4) stop-cocking will increase current production and decrease gas-oil ratio. When such relative well performance is indicated, it follows that certain reservoir performance and operating practices may be anticipated: (I) disappointing recovery, (2) longer natural flow, (3) no active water drive, (4) better evaluation of acidizing, shooting and reworking, (5) intermittent operation of wells, (6) smaller pumping equipment required. It is significant that the basis of these important predictions is bottom-hole pressure tests that can be made immediately after completion of the wells. Introduction "'Productivity index" is the number of barrels of oil produced per day per pound per square inch of differential pressure between the reservoir and the bottom of the well. "Declining Productivity Index," as considered herein, is a productivity index that has a substantially and consistently decreasing value when measured over a period of a few hours. Productivity index can be determined only when the rate of production can be stabilized. In most wells the rate of production and bottom-hole pressure are easily stabilized to give a constant productivity index for a period of many hours. A few produce so erratically as to preclude probability of an acceptable test in the usual sense. A satisfactory productivity index can be determined in some wells only by gauging the production accurately by hours, measuring the bottom-hole pressure continuously, and from these data calculating the productivity index for successive hours. Such figures frequently will have a decreasing value—that is, a declining productivity index—and when plotted on double. logarithmic cross-section paper with productivity index as ordinate and time as abscissa will be a straight-line curve. The angle between the curve and the abscissa is referred to as the rate of decline. Declining productivity index may appear to be the result of change in permeability to oil due to decreasing saturation of oil and increasing saturation of gas in the reservoir. It is possible that such is in fact the cause, but if so, more is involved than merely relative saturation of oil and gas. This seems evident because the rate of decline in productivity index is substantially the same regardless of the pro-

Jan 1, 1945

By H. W. Gillett

WE hear much in these days about "tailor-made" steels. Farseeing executives have sensed the demand for metals of improved and special properties, with those properties deliberately built into the steel in order to fit it for a particular use or group of uses. They have set their metal-lurgists at work to produce what the customer needs, even though the tonnage required may not, at least at first, be great. As the metal-lurgists bring out such metals, the products are advertised and the customer becomes increasingly conscious that he no longer has to take "ready-made" steel as the only thing available, whether it fits his needs or not, but that there are plenty of steelmakers ready to serve his specific needs with a tailor-made steel. Of course this is nothing new in the realm of rather highly alloyed steels to be heat-treated. The automotive industry demanded and got such steels long ago. Indeed, one could not design a modern car using only non-heat-treated carbon steel, since an engine of present horsepower would be so heavy that the gasoline required merely to lug the engine itself around would be absurd. Many different alloy steels and many different heat-treatments are required to produce the fine gradations of properties and the strength per unit weight that are needed in each particular part. Aircraft designers, of course, count a high strength-weight ratio in the materials used as Article I in their constitution, and they too, and in outstanding degree, require tailor-made alloys. Aircraft and automobiles may be considered as the tail coats and Tuxes of the metallurgical tailors. Nowadays there is also a demand for business suits, in the form of high-strength alloys to reduce dead load and so increase payload, all through the transportation industry. We hear most about weight-saving design and materials in respect to the railroads, with the spectacular new high-speed passenger trains and the prosaic freight car. The latter sounds especially sweet to steel-mill ears, because it means tonnage. While most of us think of these developments, and of the engineering acceptance of high-strength materials as "new," the fundamentals are of almost hoary antiquity. It is the widespread availability of a variety of materials and their general acceptance that are new.

Jan 1, 1936

By M. R. Geer, H. F. Yancey

Although the use of dense suspensions for coal cleaning was pioneered in the United States with the Chance sand flotation process, and during the past year a pilot plant using a magnetite suspension has started operation in this country, the more recent developments in this field of coal cleaning have occurred principally in the Netherlands. During the thirties the Dutch developed the Barvoys process, in which a medium of barite and clay is employed, the Tromp process, which utilizes a magnetite suspension, and the Loess process, in which is used the air-borne earth or soil known as loess.1-3 All these processes are finding increasing use in European coal-cleaning practice. Now a fourth process, the cyclone cleaner, is under development by the Netherlands State Mines. A cyclone thickener for reclaiming and thickening the dense suspension is a novel feature of the Loess process. Through accident, the discovery was made that the cyclone could be utilized as a cleaning device for fine coal. When the cyclone thickener at the Maurits mine plugged, the overflow was found filled with clean coal free of refuse, and from this observation developed the concept of the cyclone as a coal cleaner. In June 1945 the cyclone cleaner was observed by one of the authors,' and in September 1945 it was described by Dries-sen6 in a paper presented in London before the Institute of Fuel. As the cyclone seemed to offer unusual promise as a means of extending heavy-medium cleaning to the finer sizes of coal that cannot readily be treated in existing heavy-medium processes, the Bureau of Mines, following Driessen's, presentation, launched an investigation of the cyclone as a coal cleaner. Added impetus was given to this study by the present increased interest in heavy-medium cleaning in this country. Object and Scope of Investigation Driessen's report, although comprehensive in many respects, did not include a detailed description of the cyclone cleaner, and contained almost no information on the influence of the various operating variables of the cyclone. It was necessary, therefore, to investigate the influence of the cyclone adjustments on its performance before studying the application of the cyclone to various coal-washing problems. The present report is confined entirely to these preliminary tests, designed to demonstrate the operating characteristics of the cyclone. The investigation has been in progress

Jan 1, 1949

By Paul J. Sirkegian

The problem of properly controlling the movements of underground trains in the Emma Nevada and Morris Brooks workings of the Consolidated Coppermines Corporation of Kimberly, Nev., became more complex as the rate of production increased. Ore from these mines, which are connected through a 7000-ft. single-track haulageway (Fig. I), is hoisted through the Emma Nevada shalt. All production to date has been from one level. Because of heavy ground, even on the main haulage horizon, experience has shown that it is necessary to have a minimum cross section in the drifts, thus making it impractical to have a double track system. In 1937, production was 3000 tons per day; in 1938 it was increased to 6000 tons per day and in 1940 to 9000 tons per day. Each increase necessitated a revision in the method of controlling the underground traffic. In 1937 the tramming signal system consisted of a few signal lights in the main haulage drift. These lights were two 100-watt bulbs in a metal box that had one green and one red lens on each side. The box was mounted on the underside of a drift cap timber and could be seen For a considerable distance. The lights were so arranged that all boxes showed either red or green at the same time and all were controlled by a magnetic contactor at the entrance to each lateral drift. When the lights showed green, the main haulage was clear of traffic and a train could enter it. As the motor entered the main haulage drift, the motorman pulled the cord of the magnetic contactor switch, thus changing all the main haulage lights to red, which indicated that no other train could use the main haulage until the first train had turned into a lateral drift. When a train left the main line, its motorman pulled the cord connected with the magnetic contactors, causing the haulage lights to show green again. This arrangement permitted only one train at a time to use the main haulage and thus limited the number of train trips per shift, but it was satisfactory when the ore handled was only 3000 tons per day. Second SystEM Installed With a gradual increase in production it became necessary to place a train dispatcher in charge of all trains. He controlled their movements orally, giving his orders direct or by mine phone, instructing them where to load, when to leave for the station and when to return. His objective was to group several trains traveling in the same direction. Because of the human element involved, some mistakes were made. The danger of a serious collision was always possible. There was a 90° turn and curve in the underground haulageway, therefore travel in this section was always dangerous if mistakes were made in directing traffic. To protect the train crew, particularly the rear switchman who rode the last car or caboose, a two-way push button and flash-signal system was installed on the

Jan 1, 1946

By Earle Schumacher

COPPER-CALCIUM alloys are of interest as materials for use in deoxidized conductors of high conductivity. That calcium is effective in deoxidizing and degasifying copper is well known. Brandenberg and Wiens1 have described the use of calcium in the casting of sound copper and state that the deoxidation can be carried out without difficulty. The castings that they prepared were sound and sufficiently ductile to permit wire drawing. Pratt,2 in British Patent No. 1699 (1907), has claimed the use of calcium for the deoxidation and degasification of copper. Masing3

Jan 1, 1929

By C. R. Kuzell

ALTHOUGH furnaces constructed of refractory brick have been oper-ated for many decades, there has always been an unfulfilled desire by the operators for a less arduous and more satisfactory method of patching weak spots and burned-out zones in order to postpone and to effectively extend the termination of a furnace campaign. Not only has this desire frequently arisen when small spots have approached incipient failure while the furnace structure as a whole was still in good condition, but also when larger areas showed signs of needing replacement. The availa-ble methods have been arduous, sometimes dangerous, inefficient with respect to the life of new refractory material used, and nearly always have necessitated interruption of the continuity of the furnace operations and therefore reduction in furnace production during the period of time required for the repair work. Most of these older methods have involved the replacement of masonry by refractory shapes in the weakened areas. Many attempts have been made to develop a method of patching the burned-out areas by spraying granular refractory material upon old surfaces. While some success has been attained in attempts to renew the grooved, corroded side walls and fettling, and the edges of hearths, there have been no known successful applications of the spraying method in patching the underside of arches of operating furnaces. The method developed recently at the Clarkdale smelter of the United Verde Branch of Phelps Dodge Corporation, at Clarkdale, Ariz., and described in this paper, has been found to be not only convenient and successful with respect to patching vertical or inclined surfaces, but has met with a marked degree of success in patching the parts of furnace arches that are exposed to flame, the successful result being obtained with-out interruption or interference with the continuity of furnace operations. ? It may be described as a method of renewing the interior refractory sur-faces of operating furnaces by pneumatic spraying of an aqueous suspen-sion of finely divided particles of refractory material. It has been used

Jan 1, 1939

By Noel H. Stearn

To the successful functioning of the geomagnetic method of exploration in engineering and geological practice there are two prime prerequisites : the measurability and the interpretability of significant magnetic anomalies. A magnetic anomaly may be defined as a permanent distortion of the earth's magnetic field, in order to distinguish it frog the distortions, either cyclic or irregular, which vary with time. So far as known, time fluctations have no directly assignable geologic significance in terms of rock formations, while anomalies may be considered to be directly caused by the difference in the magnetic properties within and between the formations of the substances that make up the earth's outer shell. As is effectively pointed out by L. B. Slichter,1 the effects which these differences produce on the magnetic field may be extremely minute or extremely great, depending upon the magnetic properties of the formations. Thus the actual anomalies may range from the infinitesimal to a magnitude considerably greater than that of the earth's field. The geomagnetic method of exploration has shared in the deluge of experimental effort which has lately swept geophysical prospecting to its present important place in engineering and geologic practice. But to date more of this effort has been expended upon the measurability of anomalies than upon their interpretability. The tendency has been to strive for the development of instruments and especially field techniques capable of measuring minute anomalies with a precision far beyond that for which there can be any hope of adequate interpretation other than as interesting phenomena having numerous possible causes. Such efforts, of course, are highly commendable in the field of so-called pure science, which includes the accumulation of undigested detailed observations and admits of interpretation by multiple hypotheses, but in engineering practice the factor of economy must enter. Those instruments and techniques are most desirable which can most rapidly measure the interpretable range of anomalies with the precision necessary

Jan 1, 1932

Coal Division Industrial Minerals Division Minerals Beneficiation Division Mining, Geology and Geophysics Division Elmer A Jones, President President-elect Will Mitchell, Jr, Past President J B Morrow, Eastern Regional Vice-President G Donald Emigh, Central Regional Vice-President J D Forrester, Western Regional Vice-President R B Ladoo, Treasurer John Cameron Fox, Secretary AIME 29 West 39 St, New York 18, N Y

Jan 1, 1957

By Frederick Rhines

IT has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick's law (equation 1 below), ? in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick's law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Jedele and of Jedele.§ These data are essentially for one temperature alone and do not furnish any information on the variation of the activa-tion heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a singles olid solution field. Much of the argument concerning the properties of metals that deter-mine D and Q has been drawn from data in which variations of the quan-tities with concentration are unknown, for these data- have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concen-trations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By James R. Finlay

At first blush one is tempted to say that iron-mines are like any other mines, and that principles governing miniug-property in general will apply to them. But there are certain considerations which seem to repay reflection. Gold and copper are more or less independent of transportation. The proof of this is that those metals are profitably mined and shipped from the remotest corners of the earth. Their value is determined by the cost of production on the ground. This is quite true of gold, not quite so true of copper, not at all true of iron. If New York were a. fishing-village and Chicago a swamp, Calumet & Hecla might still be a bonanza. The main element of its value is the 60 lb. of fine copper per ton which it produced for years. But the Mesabi Range is absolutely dependent upon the industrial activity in the United States. Iron-manu-facture in Europe would give it no value whatever. If Chicago and New York had a population of Peruvians or Hindus, the Hull-Rust mine would be as worthless a bit of landscape as any tundra in Alaska. I have discussed these facts more or less casually and dimly in my book on the cost of mining and in my report to the Tax Commissioners of Michigan.1 I shall try here to bring them out in more detail. I have already referred to some differences in the problem of mining as between the more precious metals, e.g., gold, and the less precious and more abundant minerals, like iron and coal; but it is interesting to note that the literature of the eco-

Jan 1, 1914