Search Documents

AT the meeting of the Board of Directors on Jan. 28, 1927, the tentative budget of this Institute for next year was discussed, and in connection with the evident necessity for a larger income to meet increasing demands for service, the advisability of in- creasing the dues of members, was brought up. W. Spen- cer Hutchinson advocated an upward revision of the dues "believing it necessary that the Institute have a larger income, in order that it may carry on necessary work and render adequate service to its membership." Since this is a matter that directly affects every member, .President Taylor was directed to appoint a committee, which he did, consisting of George D. Barron, W. H. Bassett, and R. H. Sweetser, with T. T. Read as secre- tary, to bring in a tentative outline of the main factors in the problem for discussion at the annual meeting, on Feb. 15, and to prepare, after they have had the benefit of the discussion at that meeting, a report for the board. The amount of the annual dues is fixed by the con- stitution and can only be changed by proposing an amendment to the constitution. This amendment would have to be submitted to the members by letter ballot at the time of the election of officers for 1928, so that no change can be made in the dues for 1927 in any case. WHY THE INSTITUTE NEEDS MONEY At the annual meeting past-president Reynders, as chairman of the executive committee made the follow-ing report, which since it admirably sets forth the rea-sons why an increase in the dues has been suggested, is included here. "The report of the president has covered the situation so fully that little is left for me to say. However, a word in regard to the functions of the executive com-mittee may not be out of place.

Jan 3, 1927

By Emile Gyss

THE speed of drilling rock has become an impor-tant factor in mining operations, while the place-ment of holes, kind, and quantity of explosive used. are equally important. These are a function of the rock hardness and toughness. Both of these fac-tors must be considered in compiling a table that will enable a mine operator or engineer to estimate drilling speeds in a given rock, knowing its hardness, and from its toughness, the dynamite required. The hardness of a homogeneous rock may be defined as its resistance to a penetrating medium, such as a drill-steel bit, and toughness, its resistance to with-stand rupture by the tearing apart of its minerals or parts of the same mineral. Rock hardness, as it has here been defined, is a function of the hardness of the component grains composing it, as well as grain size, shape, arrangement, and binding minerals. Rock tough-ness depends on substantially the same factors, but is measured by a totally different method. The units in which rock hardness is usually ex-pressed are either relative values or alphabetical desig-nations which carry no definite quantitative meaning. R. M. Raymond has suggested the measurement of com-posite rock hardness, based on mineral hardness as ob-tained by the Moh scale. This is done by multiplying the percentage of each mineral in a rock by the Moh mineral hardness and dividing by 100. These values convey a clearer conception in the minds of men in-terested in rock work -and are the basis of the units used in Tables 1 and 2. The hardness of rocks as it has been variously de-fined may be determined by different methods. The first method is one in which the proportionate average of the hardness of minerals making up a rock is the basis for classification. The other factors of grain size, shape, arrangement, and binding power are not considered.

Jan 6, 1927

By J. E. Tobey, David R. Mitchell, J. H. Kerrick

DETAILED knowledge of purchase specifications established by coal consumers is essential to the successful design and operation of a coal-preparation plant. ANTHRACITE Specifications should be considered by both the consumer and the producer as guide posts outlining a certain path for both to follow. Plants differ, therefore specifications must differ to meet the varied requirements. Specifications are not of themselves a "cure all" or an assurance of complete satisfaction in fuel utilization. Specifications should not be regarded as a license to engage in an orgy of buying any and all coals that may happen to fall within their limits. This would lead to the indiscriminate mixing of coals which may vary in their burning characteristics. Different coals of equal grade tend to be individualistic in their burning characteristics. Rather, specifications should be used to help simplify coal selection, to reduce the actual number of coals used over a given period; in other words, to have a stabilizing influence on coal or customer turnover. In the final analysis, the use of too many coals per year in a plant is costly to both the consumer and the producer. Too many sources usually result in higher operating and maintenance costs for the consumer and higher sales costs for the producer. Finally, the statement included in the report accompanying the com¬prehensive Coal Selection Charts prepared by the Coal Committee of the National Association of Purchasing Agents, and released in 1938, is significant. This Committee worked diligently for a period of 15 years seeking to find a scientific and reliable method for selecting coals. The two following paragraphs are quoted from its report: More important is the fact that no ready-made classification or set of specifications can possibly replace the judgment and resourcefulness of an experienced combustion engineer or fuel technologist, nor the usual need for full scale plant tests under the exact conditions of use before a final decision is made ...

Jan 1, 1943

By Thomas Fraser, David R. Mitchell

THE primary purpose of the loading plant is to transfer the finished product from the preparation machines to the railroad car, truck, or barge in which it is to go to market. Secondary purposes of the loading plant are: to prevent excessive degradation of sizes during loading, to reduce segregation as much as possible, and to prevent excessive quantities of very good or off-grade coal from entering any one car. Nonuniformity of consignments is one of the chief sources of com- plaints by consumers and coal merchants. A properly designed loading plant will do much to reduce complaints and ensure uniformity, not only from shipment to shipment but also in each individual consignment along the length of the car and in cross section. DEGRADATION IN STORAGE, LOADING AND SHIPMENT The object in loading is not only to handle the coal without breakage and segregation, but also to produce a well-trimmed load that will ride to its destination without spillage or breakage en route. The small sizes present in a car of prepared coal as received by the purchaser consist of: missed small sizes not screened out in the preparation plant, breakage during loading, and breakage caused by handling en route. For domestic sizes of anthracite shipped from the Pennsylvania anthracite field to Atlantic coast cities, the dealers' loss because of break- age in loading and shipment amounts to from 2 to 5 per cent and for anthracite shipped to Middle West cities, the loss is 8 to 9 per cent. This difference is in part because dealers in the Middle West rescreen their coal more thoroughly than is usual in the East. One dealer handling Illinois No. 6 coal shipped from southern Illinois mines to Chicago reports an average size loss of 10 per cent when lump coal is unloaded with a fork. This runs as low as 5 per cent for carefully loaded coal and as high as 15 per cent for carelessly loaded coal.

Jan 1, 1943

By F. G. Jaicks

RECOGNITION of the benefits to be gained from the continuous casting of molten steel into finished or semifinished products has been given by scientific minds since the very beginnings of steel plant technology. In fact, Sir Henry Bessemer is credited with the first of a long list of patents' issued by the U. S. Patent Office for a process which would accomplish this desirable end. None of these early ideas attained practical success and, as a result, the conventional method of teeming into ingot molds became an integral part of modern steelmaking operations. This procedure, although refined to keep pace with the changes which have come about in steelmaking and finishing facilities, is recognized to have inherent shortcomings which adversely affect manufacturing costs and steel quality. Interest in the continuous casting of steel persists because the process is directed toward avoiding some obvious weaknesses of conventional ingot casting. It has been recognized that should it be possible to substitute any of the continuous casting techniques under current development for ingot casting, it would no longer be necessary to make large capital investments in primary rolling equipment, the sole purpose of which is to reduce ingot castings to a form rollable on finishing mills. The results reported in the continuous casting of non-ferrous metals and specialty steels indicate that in addition to avoiding the primary rolling mills there is some basis for expecting significant improvements in yield, surface, and internal quality. Recognizing the shortcomings of the conventional procedures, the Inland Steel Co., in cooperation with Atlas Steels Ltd. and the Freyn Dept. of the Kop- pers Co. Inc., embarked upon a program to evaluate certain aspects of continuous casting in order to determine whether the process could be applied practically to an existing integrated steel plant producing 'large tonnages of carbon steels. TO assist in this evaluation a study was carried out in which several types of low carbon steel were continuously cast in an existing machine. It is the purpose of this paper to review some of the results obtained in the casting studies and to interpret the information that was obtained so as to indicate factors that must be considered in assessing operating limitations and plant capacities. Despite the early interest in the continuous casting of steel, the actual application to the steel industry is relatively recent. At present, there are about 25 operating plants casting steel, most of which have been built in the past decade. None of these plants could be classified as large in terms of the tonnages that are being processed by the major integrated steel plants. In contrast to the situation in the steel industry, there has been widespread adoption of the continuous process in the casting of nonferrous alloys, particularly aluminum and copper. As a result, much of the basic information that was required to apply the process to steel was developed in the nonferrous industries. In this respect, a most important contribution was the development of the Junghans2 system, which was initially designed for the casting of nonferrous metals and later applied to the casting of steel. Alternative methods for casting have also been proposed by Babcock and Wilcox Tube Co.,'" the British Iron and Steel Research Association,5 and the Gebruder Bohler A. G.13 Each of these methods is now being used successfully for the casting of special steels in small experimental plants or in modest sized commercial steelworks. The Original Junghans process was first developcd in Germany. Further application of the process has been made by Rossi in other countries.'*' The experi-

Jan 1, 1958

George Edward WebbeR, a member of the Institute since 1906, died in San Francisco, May 29,1922. Born in Dixmont, Me., in 1852, he went to California in 1857 where he lived until 1883 and received a thorough training in precious metal mining in the employ of his father and J. B. Haggin. In 1883, he went to the Black Hills, South Dakota, as superintendent of the Father DeSmit mine; later the Deadwood Terra also came under his management. These mines are now part of the Homestake Mining Co. In 1889, the Rothchilds asked Hamilton Smith to recommend an engineer to take the place of the late Henning Jennings, who had resigned from the El Calloo Mining Co., of El Calloo, Venezuela, in order that he might proceed to South Africa. Mr. Webber accepted the position, remaining there until 1893 when he returned to the United States on his way to Johannesburg, South Africa, where he had been appointed manager of the Crown Reef Mining Co., Ltd. Early in 1896, he became general manager of the Rand Mines, Ltd., and served in this capacity until 1911. During the latter part of this period, Mr. Webber was active in the greater amalgamations of H. Eckstein & Co., and it was largely on his advice that H. Eckstein & Co. carried out the negotiations preceding the formation of the Crown Mines, Ltd. On his retirement from South Africa, he returned to live in Ross Valley, near San Francisco, Cal. The Rand Mines, Ltd., of which Mr. Webber was general manager, was the largest company controlled by Wernher Beit, the leading London house interested in South Africa mining, whose local agents in Johannesburg were H. Eckstein & Co. This firm is now known as the Central Mining & Investment Corpn., and after the departure of Henning Jennings, Mr. Webber was the firm's most valued and confidential advisor and was very highly thought of in mining circles in South Africa. He was a ma of most upright and straightforward high character, plain spoken and sincere; and his recognized high character was one more qualification which aided his great success.

Jan 1, 1923

George Edward WebbeR, a member of the Institute since 1906, died in San Francisco, May 29,1922. Born in Dixmont, Me., in 1852, he went to California in 1857 where he lived until 1883 and received a thorough training in precious metal mining in the employ of his father and J. B. Haggin. In 1883, he went to the Black Hills, South Dakota, as superintendent of the Father DeSmit mine; later the Deadwood Terra also came under his management. These mines are now part of the Homestake Mining Co. In 1889, the Rothchilds asked Hamilton Smith to recommend an engineer to take the place of the late Henning Jennings, who had resigned from the El Calloo Mining Co., of El Calloo, Venezuela, in order that he might proceed to South Africa. Mr. Webber accepted the position, remaining there until 1893 when he returned to the United States on his way to Johannesburg, South Africa, where he had been appointed manager of the Crown Reef Mining Co., Ltd. Early in 1896, he became general manager of the Rand Mines, Ltd., and served in this capacity until 1911. During the latter part of this period, Mr. Webber was active in the greater amalgamations of H. Eckstein & Co., and it was largely on his advice that H. Eckstein & Co. carried out the negotiations preceding the formation of the Crown Mines, Ltd. On his retirement from South Africa, he returned to live in Ross Valley, near San Francisco, Cal. The Rand Mines, Ltd., of which Mr. Webber was general manager, was the largest company controlled by Wernher Beit, the leading London house interested in South Africa mining, whose local agents in Johannesburg were H. Eckstein & Co. This firm is now known as the Central Mining & Investment Corpn., and after the departure of Henning Jennings, Mr. Webber was the firm's most valued and confidential advisor and was very highly thought of in mining circles in South Africa. He was a ma of most upright and straightforward high character, plain spoken and sincere; and his recognized high character was one more qualification which aided his great success.

Jan 1, 1923

By J. N. Roberts, K. V. Gow

In a recent review of the field of plastic deforrnation of metal single crystals, Maddin and chenl indicated the need for systematic investigations of the crystallography of the slip process with special attention to: a) The effect of the orientation of a crystal on the appearance of slip lines, b) The effect of high temperatures on the slip systems of aluminum, c) The effect of strain rate on the crystallography of slip. The present paper deals with the effect of temperature and strain rate on the mechanism of deformation of aluminum single crystals similarly oriented for single and duplex slip. The work of several investigators has shown that in aluminum at high temperatures other slip systems in addition to the predicted {I l l) <101> may operate. The most generally reported additional systems

Jan 1, 1959

By A. English, M. J. Greaves

This paper is a discussion of pelletizing systems developed over the last 15 to 20 years for the agglomeration of fine iron ore concentrates. Five different pelletizing systems are now in commercial use in the U.S., and for the purposes of comparison, estimated operating costs and capital costs for the construction of four of them are included. Capacities of existing commercial plants are examined, together with the anticipated capabilities of plants presently being built or projected. In just 21 years, the art of pelletizing iron ore concentrates has reached maturity with mastery of the separation of finely divided concentrates from low-grade iron ores and their agglomeration into pellets containing about 65% iron. This accomplishment has firmly established an improved feed for the blast furnace, with resulting benefits in faster reduction of burdens and greater economy of operation. The present production capacity of pelletizing facilities in the U.S. is about 20 million tons annually, and it is expected to double by 1970. The rapid expansion of pelletizing in the U. S. has been closely observed in European countries, notably in Sweden and Germany, where pioneer agglomerating techniques were developed early in this century. PELLETIZING PLANTS AND PROCESSES Twelve commercial pelletizing plants are presently in operation in the U. S. and Canada. An equal number are in various stages of engineering and construction, and many others are being considered. The pelletizing systems currently employed include shaft furnaces, horizontal grates using three different airflow arrangements, and grate kilns. The capacity of pelletizing operations in North America is shown in Table I. All of these plants are integrated with the mine, the ore-crushing facilities and the concentrating plant and are equipped with storage and loading-out facilities for the product. Normally, a pelletizing plant is composed of a shuttle conveyor above the receiving bins; balling equipment; a heat-hardening system including the necessary auxiliaries such as furnaces, burners and controls, ducts, fans, meters and instrumentation; fines recovery equipment; and product handling equipment. Also included are the necessary auxiliaries and utilities such as boilers or power plant; oil unloading and storage facilities; coal unloading storage, grinding and distribution facilities; and bentonite or other additive storage and distribution equipment. Shaft Furnaces: Vertical shaft furnaces used in this country are limited to the treatment of natural magnetite concentrates containing minor quantities of residual fluxing elements. Fig. 1 shows a perspective view of the shaft furnace with balling, feeding and pellet-handling equipment. An elevation of a shaft furnace is shown in Fig. 2. A commercial shaft furnace unit is about 45 ft in height with a 6 x 14-ft rectangular cross section and has a nominal production rate of approximately 50 gross tons of pellets per hour. The upper portion of the furnace shaft is constructed of fire brick as protection from the high process temperatures involved. The lower portion of the shaft is lined with abrasion-resistant brick to withstand erosion from the fired pellets. Rectangular-shaped, refractory-lined and insulated combustion chambers are situated on each side of the shaft furnace. Oil or gas is burned to produce high temperature gases which are forced into the furnace through ports located near the top of the combustion chambers. The shaft furnaces operate at a pressure of approximately 6 psi. Pellets are fed into the top of the furnace by a pantographic feeder designed to produce the desired pellet stockline. The furnace is kept filled at all times and pellets are fed and discharged from the furnace at the same rate. In early development, 10 to 12 lb of solid fuel was incorporated in the pellets. However, the main source of process heat is now derived from the combustion chamber gases. In some instances no solid fuel is used. The pellet movement in the shaft furnace is counter-current to the flow of gases. Ambient air is introduced through louvers at the lower end of the furnace, at about 6 psi, cooling the fired pellets and supplementing the heat of the high temperature gases from the combustion chamber ports. The zone of maximum temperature, located above the ports of the combus-

Jan 1, 1963

By S. W. Nabbs, W. D. Bachman, A. W. Last

A study has been made of wet, autogenous grinding of disseminated copper ores, including testing of a large number of samples from. Kennecott Copper Corp.&apos;s Chino mine. The grindability of the various samples was found to vary over an extremely wide range, even among samples taken from diflerent locations within the same ore body. These variations in grindability can be qualitatively correlated with the composition of the rock and the fracturing and alteration that had occurred. Because of the large-scale nonhomogeneity of disseminated copper ore bodies, extensive and careful testing of autogenous grinding is needed. An accurate correlation of the grinding data from various samples with the geology of the ore body and with mining plans will indicate if variations in grinding mill throughput can be avoided in practice by mixing or blending of mill feed and if, therefore, autogenous grinding can be applied successfully. In the past 15 years, comminution by primary autogenous grinding has been investigated and applied economically in the minerals industry, particularly in iron-ore processing. Successful application of primary grinding is described by A. A. Dor,l.&apos; P. B. Dettmer,334 R. R. Turner, and W. F. McDermott." other authors describing the advantages of primary grinding include H. Hardinge,&apos; R. T. Hukki,&apos; D. S. Coyle" and F. C. Bond,"," to mention only a few. For the past several years, Kennecott Copper Corp.&apos;s Metal Mining Div. Research Center has been investigating primary grinding of disseminated copper ores. Both fully autogenous and semi-autogenous grinding has been explored. Ores from three of Kennecott&apos;s western operating properties and from several development properties have been tested. Host rocks include diabase, schist, silicated and argillaceous limestones, shale, granite porphyry, quartzite, and granodiorite. The object of this paper is to supplement the general knowledge in the field of primary grinding by presenting information gained from the studies with the various disseminated copper ores. Data are presented which show that carefully considered test programs are required to determine the practicality of applying autogenous grinding to a specific mining-beneficiation operation. Particularly this is so if more than one rock type occurs within an ore body or if there are wide variations in the degree of rock alteration within a deposit. Extensive sampling and subsequent testing of the ores within a mine are required if serious pitfalls are to be avoided and good engineering data acquired. We hope that this presentation will stimulate studies to increase the understanding of the fracturing process applicable to large pieces of rock, a factor which is important in autogenous grinding. Test Facilities and Procedures Both pilot-scale and full-scale test facilities were used to investigate primary grinding characteristics of the disseminated copper ores. A 6-ft Hardinge Cascade mill, a 24-ft Hardinge Cascade mill, and a 5-ft Aerofall mill were used in the studies. The Cascade mills were operated wet, while the Aerofall mill was operated both wet and dry. The Cascade mills were operated both for fully autogenous and for semi-autogenous grinding; the Aerofall mill was operated only semi-autogenously. Fully autogenous grinding, as the term is used in this presentation, is defined as the direct grinding of coarsely crushed rock by the action of the rock mass. Semi-autogenous grinding is defined as the grinding of coarsely crushed rock with the rock mass supplemented by a steel ball charge. Most of the test work was done using the 6-ft Cascade mill, operated under fully autogenous grinding conditions. Only limited testing was conducted with the 5-ft Aerofall mill and only one ore was tested using the 24-ft Cascade mill. This presentation is concerned, therefore, primarily with fully autogenous, pilot-scale grinding in the Cascade mill. Fig. 1 presents a diagram of the test facilities used with the 6-ft Cascade mill. Principal test equipment consists of a 6-ft Cascade mill, an 18-in. spiral classifier, an elevator, a 2 x 9-ft belt feeder, a conventional integrating kilowatt-hour meter, and a recording wattmeter. In testing, feed charges, adjusted as to weight, were deposited as evenly as possible on the belt feeder every 15 min. The weight of each charge was adjusted to maintain a mill charge of 27 to 30% of mill volume. The classifier was adjusted to obtain the desired size-consist of the final product, generally at 20% + 100 mesh. After equilibrium was established in the circuit, the feed, mill discharge, classifier sand, and classifier overflow were sampled and their size distributions determined. During the sampling periods, the power drawn by the mill was measured to determine the energy consumed in the reduction of the size consist of the ore solids. Fully Autogenous Pilot Grinding Tests on Various Kennecott Ores Typical test results obtained in the 6-ft Cascade mill with samples from Kennecott&apos;s Ray Mines Div., Chino Mines Div., Utah Copper Div., and a development property designated as Mine A are presented in Table 1. As shown, the ores that were ground most easily in the pilot-scale mill were composite mine samples obtained

Jan 1, 1971

By F. R. Hensel

Up to the present time few attempts have been made to produce hard nonmagnetic materials by heat treatment of austenitic steels. The usual result has been to cause them to pass into the martensitic stage, thus destroying to a great extent the typical austenitic properties, since this involves a transition of a portion of the iron from a face-centered to a body-centered type of atomic arrangement. High-strength nonmagnetic materials such as might be provided by properly hardening austenite are required in the electrical industry for different machine parts. In Europe nonmagnetic retainer rings for restraining the end-turns of the rotor windings in turbo-alternators have been developed as a special application of high-strength austenite. In testing1 a 28,000-kva. three-phase Siemens turbo generator running at 3000 r.p.m. at full load current, the losses in the short-circuit test were 450 kw. for the magnetic ring and 286 kw. for the nonmagnetic, and the difference should be attributable to the magnetic ring. The differences in temperatures during the same test are given in Table 1 and these show the advantage of a nonmagnetic over a magnetic retainer ring.

Jan 1, 1931

By Paul D. V. Manning

MAGNESIUM is an exceedingly strategic material but the importance of its production at the time this war started was not realized. Our Government then suddenly became much alive to the need of a tremendous increase in magnesium output, and became a participator in the industry. In this paper an attempt will be made to given an over-all picture of the industry as it has been, and is being, developed. The present war is giving a great acceleration to the use of lighter metals. Development of facilities for production of great tonnages of aluminum and magnesium is bound to bring about some interesting changes in later peace times because costs will be low and production capacities high. As our knowledge of the metallurgy of magnesium alloys increases, this metal will become of vital peacetime importance and will be used in ways we do not now imagine. Household refrigerators, furniture, automobiles, even houses will all be lightened through the use of magnesium.

Jan 1, 1943

By R. F. Yap, N. Arbiter, C. C. Harris

A fully-instrumented driving mechanism has been constructed to study the power, aerating and solid suspension characteristics of several laboratory flotation machines. Machines operating over normal flotation speed ranges give substantially constant power numbers in liquid systems indicating that they operate close to fully baffled turbulent flow conditions. Owing to lack of geometrical scaling, power numbers for different sizes of cells of the same make are different. Even larger differences occur between cells of different manufacturers. For a given impeller, varying the tank size did not significantly affect the power consumption. Tank geometry and baffling has a slight effect on power consumption with shrouded impellers. For a given impeller speed, suspension height decreases while power increases with increasing mass of solids in suspension. While power consumption is hardly affected by particle size and clearance between the impeller and tank bottom, the suspension height significantly increases as clearance increases and as particle size decreases. Aeration was found to affect not only power but also the suspension characteristics of the machine. For closely sized particles, drastic sedimentation occurred when a critical value of the air flow number was exceeded. The critical air flow number decreased with increasing particle size. This effect was less marked with a wide particle size range. The self-aerating capacity of flotation machines increases with cell size at a given speed for the same impeller-shroud system, but decreases in the presence of frother and solids. Equations have been established for correlating all of the studied variables. Data taken from the literature were also correlated with these equations. The modern mechanical flotation machine has, over a period of 60 years, displaced other designs to become the dominant type. Once the correct chemical environmental conditions have been established, the major requirement, selective mineral-air adherence, is essentially a function of two operating variables — impeller speed and air rate. The special nature of this dependence is such that in the same apparatus, but under different operating conditions, adherence can be either prevented or destroyed. Another aspect of this observation is that flotation machines though differing in detail to a considerable extent can produce similar metallurgical results. It must be concluded that having determined the correct reagent levels, establishing the correct operating conditions are at least as important as machine design. Since about 1960, after 30 years of fairly stable circumstances, manufacturers have been developing new types of machines whose major feature is emphasis on pulp flow characteristics by virtue of new im-peller-stator designs. As far as can be ascertained, these new designs necessitate radical departures from accepted impeller speed-air rate values. Performance data are still awaited. Flotation machine development has been empirical, as is selection of operating conditions. The purpose of the work at Columbia University has been to elucidate the fundamentals of the subject so that the purely mechanical aspects of the flotation process can be understood in hydrodynamic terms.1-6 Hopefully, this might lead to intelligent selection of a particular machine and its operating conditions for a specific ore based on a minimum of testing, or even to new types of flotation machines. The present investigation is the most comprehensive to date.7,8 Earlier work, which was largely exploratory, has been repeated and extended and employes the most accurate measuring techniques available. Additionally, sufficient hydrodynamic data were obtained under flotation conditions to delineate the relevant operating ranges. Attention has been given to scaling in that several geometrically scaled tanks and impellers have been constructed and tested; it has been pointed out elsewhere that undistorted geometrical scaling rarely pertains in flotation machine design.5 This paper is divided into sections dealing with relevant combinations of the three phases: liquid, air and solid. Summaries of the literature have been given in previous publications2-4 and will not be repeated here. Recently, several reviews of mixing have appeared, which can be usefully referenced.9-11 It is of interest to note that flotation is not included

Jan 1, 1970

By S. A. Swensrud

REPORTS from smelters show that all were so occupied with the in- creased production called for during the first half of the year that little time was devoted to metallurgical developments. Improvements which have been made such as gas-firing and other alterations ill the reconstructed Hayden smelter, will require time for reporting. The labor situation at all plants held the most prominent place and put all other problems in the background. Coming events of considerable importance concerti the construction of two new smelters. The Chino unit of Nevada Consolidated which has long had its concentrate smelted at the El Paso plant of the American Smelting and Refining Co. is constructing its own smelter at the property in New Mexico. The newest Phelps Dodge development of the Clay ore body at Morenci, Ariz., will call for another new smelter.

Jan 1, 1938

While coal was mined in New Mexico in 1860, production was on a small scale during the period considered here, and Table 77 contains all the data found. [ ]

Jan 1, 1942

By T. Okubo

Gold is generally recovered from silver anode slime by electrolysis in the final step of the copper anode slime treatment. In the present investigation, rapid and direct hydrometallurgical separation and recovery of gold in the early step of the process is studied. Gold is recovered just after the elimination of copper and selenium from copper anode slime. The studied process consists of: (a) oxidizing roasting for selenium elimination, (b) sulfuric acid leaching of the calcine for copper removal, reduction of gold in the liquor by the use of proper reductant such as hydrogen peroxide (production of gold powder), (el nitric acid treatment of gold powder for further purification and (f) melting and casting of gold. Laboratory and miniplant testwork showed that the extraction ratio of gold by chlorine leaching was 99 % up and four nine gold ingot could be recovered without electrolyses.

Jan 1, 1984

By Henry Carlisle

W. W. Mein: One of the most amusing things in Nevada City – I was born and was going to school there - was that my mother made overcoats for us, and because they were different from other boys’ overcoats, we’d hide them under a bridge and pick them up on the way home. I left Nevada City with my parents when I was about eleven years old, and moved to Oakland. This was caused by the closing down of the hydraulic mines and my father being send to the El Cayo mine in Venezuela, which was then one of the richest gold mines in the world. Hamilton Smith operated the hydraulic mines in California, and when they were closed down by the Sawyer decision, he was persuaded by the Rothschilds to go to London. There, together, they formed the London Exploration Co.

Jan 1, 1964

Abbott, Robert H., (S&apos;42) Agricultural & Mech. College of Texas, College Sta.. Texas. Abrahamson, Guy C., (S&apos;43) Univ. of California, Berkeley. Calif. Abrego, Alfredo, (S&apos;43) Texas College of Mines & Metallurgy, El Paso, Texas. Ackermann, K. G., (S&apos;43) Univ. of Alabama, University, Ala. Adamec, Lew, (S&apos;42) Colorado School of Mines, Golden, . Colo. Adams. Charles E., (S&apos;42) Univ. of California, Los Angeles, Calif. Adams, Charles W., (S&apos;30) Asst. Met., Canada Foundries & Forgings Ltd., Welland, Ont., Canada. Adams, John W., (S&apos;42) Univ. of Texas, Austin, Texas. Adams, Karl S., (S&apos;43) Univ. of New Hampshire, Durham, N. H. Adamson, Charles R., (S&apos;41) Univ. of Utah, Salt Lake City. Utah. Adler, A. G., (S&apos;41) Met. Engr., Flotation Operator Helper. Utah Copper Co.. Garfield, Utah. Adler, Frank J., (S&apos;42) Colorado School of Mines, Golden, Colo.

Jan 1, 1943

By J. Handin, S. J. Bauer, M. Friedman

Deformation mechanisms in room-dry and water-saturated specimens of Charcoal Granodiorite, shortened at 10-4s-1, at effective pressures (Pe) to 100 MPa and temperatures to partial melting (?1050°C) are documented with a view toward providing criteria to recognize and characterize the deformation for geological and engineering applications. Above 800°C strength decreases dramatically at effective pressures ? 50 MPa and water-weakening reduces strength an additional 30 to 40% at Pe = 100 MPa. Strains at failure are only 0.1 to 2.2 percent with macroscopic ductility (within this range) increasing as the effective pressures are increased and in wet versus dry tests. Shattering (multiple faulting) gives way to faulting along a single zone to failure without macroscopic faulting as ductility increases. Microscopically, cataclasis (extension microfracturing and thermal cracking with rigid-body motions) predominates at all conditions. Dislocation gliding contributes little to the strain. Precursive extension microfractures coalesce to produce the throughgoing faults with gouge zones exhibiting possible Riedel shears. Incipient melting, particularly in wet tests, produces a distinctive texture along feldspar grain boundaries that suggests a grain-boundary-softening effect contributes to the weakening. In addition, it is demonstrated that the presence of water does not lead to more microfractures, but to a reduction in the stresses required to initiate and propagate them.

Jan 1, 1982

By Howard N. Eavenson

In many of the bituminous-coal districts of this country, more than one seam of workable coal exists, and in most cases the lower seam is the more attractive, owing to either its greater thickness or its superior quality. Apprehension that the mining of a seam will destroy the availability of all overlying seams has hindered the development of many fields and has led to the unprofitable working of certain seams in order to save them from an expected total loss. The U. S. Coal & Coke Co., Gary, W. Va., was the first operator in the Pocahontas field to mine the No. 4 seam extensively, which occurs about 80 ft. above No. 3, the scam that was worked first. This was due to the fact that over large areas the upper seam was the only one of workable thickness, at that time. In two places, both seams were workable in the same area, the No. 4 being thinner and containing more impurities than No. 3 seam. In mining these areas, an attempt was made to keep the workings in the upper seam in advance of those in the lower one, and no pillar robbing was done in No. 3 seam until after pillars in that part of the upper seam directly over it had been mined. This resulted in an excessive development in the lower seam, with large areas of finished rooms and standing pillars. The top fell badly, and after a couple of years the falls became so heavy that pillar drawing was unduly expensive. To overcome this obstacle and allow No. 3 seam to be worked in some territory where No. 4 was thick, but too dirty for present use, a study was made of operating methods applied to superimposed seams in Pennsylvania and Maryland. This was started more than seven yean ago by the writer; his data, supplemented by more recent information gathered by his associates, and by two cases mentioned in recent foreign publications, form the basis of this paper. Central Pennsylvania In central Pennsylvania, the lower coal measures contain several seams of nearly the same thickness but of varying quality, and as mining

Jan 1, 1923