Search Documents

By Dustin Vickress

The premature failure of copper staves in the lower stack and bosh is frequently the cause for an interim blast furnace repair at great cost to the blast furnace owner. Protective accretions may form on the stave hot face, but when these accretions are lost the staves can begin to deteriorate both due to abrasive wear from exposure to the descending burden materials and due to thermal cracking from exposure to hightemperature process excursions. These mechanisms can lead to failure of cooling passages, which forces blast furnace operators to shut off these channels, accelerating the rate of copper stave wear. Finger cooler technology was developed to extend blast furnace life by restoring cooling to damaged staves. Evidence for their effectiveness is presented herein in the form of experimental test work and conjugate heat transfer (CHT) analysis carried out using computational fluid dynamics (CFD) simulations. These tests demonstrate that under typical blast furnace excursion conditions, a stave fitted with finger coolers will undergo half the temperature rise of a stave fitted with conventional cigar coolers.

Aug 17, 2017

By Kenneth Holmnerg

About 100 million terajoule is used annually worldwide to overcome friction and that is one fifth of all energy produced. The largest quantities of energy are used by industry (29%) and in transportation (27%). Based on our recent studies on energy use in passenger cars, trucks and buses, we concluded that it is possible to save as much as 17.5% of the energy use in road transports in the short term (5-9 years) by effective implementation of new tribological solutions. This equals to annual energy savings of 11.6 exajoules, fuel savings of 330 billion liters and reduction in CO2 emission by 860 million tonnes. In a paper mill, 15-25% of the energy used is spent to overcome friction. The electrical energy used by a paper machine is distributed as 32% to overcome friction, 36% for the paper production and mass transportation, and 32% is other losses. In paper machines, 11% of the total energy used to overcome friction can be saved by the implementation of new tribological technologies. This would result in electrical energy savings worldwide of 130,000 terajoule, economic cost savings of 2 billion euros and CO2 emission reduction of 11 million tonnes annually. An overview of the total energy saving potential by improved tribology in transportation and industry is presented.

Jul 31, 2018

By Luiz Henrique Accorsi Gans

First, this works carries an experimental evaluation for austempered ductile iron (ADI) as a gear material. And second, in order to provide a better understanding of the microstructural effect on the stress state of subsurface regions, a finite element method approach was considered using the submodeling tool in ANSYS 11.0. For this, ADI gears were produced from continuous cast iron bars, heat and thermochemical treated and tested in FZG test rig. The results were compared to those of carburized steel AISI 8620 and induction hardened steel AISI 4140 gears. The wear experiments were performed at the temperature of 90ºC with two torque stages: 135 N.m (running-in) and 302 N.m (steady-state). The time for pitting and spalling on the gears surfaces were measured using image analysis. The results showed a very good potential of using ADI for manufacturing gears, replacing induction hardened steels. Also, the ADI gear with smaller nodules showed higher life for pitting. In contact fatigue tests with severe load, the carburized AISI 8620 steel proved more adequate than the austempered ductile iron, showing that the mechanical properties are critical in the resistance to damage in gear contact. The austempered ductile iron with smaller nodule size showed to be very competitive with wear resistance similar to AISI 4140 steel induction hardened. With ANSYS, it was verified that the nodule size affects the gears life independently of the mechanical properties of the matrix. The results showed that the nodules indicate the presence of a concentration stress, but their size doesn’t affect the contact fatigue life as much as the total amount of nodules, regardless of the ductile iron microstructure. The size and number of nodules affects both the nucleation and the propagation stage of cracks. ADIs with higher amount of nodules have a greater wear resistance. Also, compared to the Hertz contact theory (isotropic material), the presence of graphite nodules indicates a non-isotropic material and made the maximum shear stress point moves toward the surface.

Jul 31, 2018

By Pedro Jorge Walburga Keglevich de Buzin

The steel production in mini mills generates several process residues, among them there is the electric arc furnace dust (EAFD). This residue has as main elements Fe, O, and Zn, being classified as hazardous by the presence of Pb and Cd. Thermodynamic studies related to the formation of mineral species containing Fe, O and Zn elements were carried on due to the influence of these compounds in hydrometallurgical EAFD recycling processes. In recent years, a rise in the chlorine content of this residue was observed, mainly motivated by the increased use of scrap with polymeric impurities containing this element. In this work, based on computational thermodynamics tool FactSage, a general overview of gaseous and minerals species (found in EAFD) formed by Fe, Zn, O, Cl, H and C is shown – representing the organic origin of chlorine. For this study, the PVC polymer was used as the chlorine carrier substance which contaminates the EAF load.

Jul 30, 2018

By Michel Fillon

Hydrostatic assistance is a commonly used method to improve limited load carrying ability of tilting-pad thrust bearings during transient states of operation of the vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves etc.), it also requires manufacturing of special recesses/pockets at the pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up of the machine and form a hydrostatic film between the pads and the collar. There is a quite wide variety of geometry of recesses (shape, depth, size) met in practical large bearing applications. The presence of a hydrostatic pocket (usually located in the sliding surface above the pivot area, where thin film, high oil pressure and temperature are observed) affects bearing performance under hydrodynamic operation. In theoretical researches, there is an almost common practice not to include hydrostatic recess in THD or TEHD analysis. This is probably due to the problems with obtaining solution for oil film geometry with pocket, with pocket depths order of magnitude larger than gap thickness. In this paper, an attempt was taken to study the effect of the lifting pocket on THD performance of a large tilting-pad thrust bearing of ltaipu power plant. Bearing performance was evaluated including recess shape for several cases of its depth. The results show, that hydrostatic recess changes calculated bearing properties quite significantly, especially in the vicinity of the pocket.

Jul 31, 2018

By Sidiney Nascimento Silva

O trabalho descreve os principais resultados dos testes industriais realizados na Usina Presidente Vargas, CSN, Brasil, envolvendo a adição de um catalisador à mistura de carvões, em termos da qualidade do coque e do processo da coqueria. O catalisador em questão é o produto Thermact, que possui partículas nanométricas em sua composição, fornecido pela empresa Abhitech Energycon Limited, Índia. O catalisador foi dosado e adicionado à mistura de carvões via correia transportadora, na proporção, em peso, de 1kg de catalisador para 4.000kg da mistura de carvões. Os resultados dos testes realizados nas Baterias # 1, 4A, 4B e 5 com a adição de um catalisador à mistura de carvões, sinalizaram a viabilidade técnica e financeira da sua aplicação no processo da coqueria. Os principais benefícios decorrentes da adição do catalisador foram: i) aumento potencial da capacidade de produção de coque ao redor de 10% ou, alternativamente, melhoria da qualidade do coque - aumento de 1,4% do valor médio do índice de resistência mecânica a frio do coque, DI150/15, mantendo-se o tempo total padronizado do processo de coqueificação, visando à preservação das Baterias, ou ainda, a utilização de uma mistura de carvões de menor custo, sem prejuízos ao atendimento à especificação do coque para os Altos-Fornos; b) aumento da geração e redução do consumo de gás de coqueria, GCO; iii) aumento na produção de BTX (Benzeno, Tolueno, Xileno) e redução da produção de alcatrão na Planta de Carboquímicos; iv) limpeza do sistema “PROven”, “goosenecks”, tubos de ascensão e paredes dos fornos, sinalizando a sua viabilidade técnica e econômica.

Aug 1, 2018

By Carolina Passanante

Aços Inoxidáveis Supermartensíticos surgiram na indústria petroquímica como um material alternativo para confecção de dutos, devido principalmente ao sinergismo de suas propriedades mecânicas e de corrosão. Com esta nova demanda, tornou-se necessária a caracterização deste material em suas diversas propriedades, destacando-se neste trabalho o efeito da microestrutura na resistência à corrosão. Objetivou-se, portanto, o estudo da resistência à corrosão por pite de um aço inoxidável supermartensítico 13Cr-5Ni-2Mo-Nb em função da fração volumétrica de ferrita-delta (d) presente na microestrutura. A variação da ferrita-delta foi alcançada através de tratamentos de recozimento, a 1.050°C, durante diferentes tempos (de 0,5h a 48h). As amostras foram submetidas a ensaios de polarização potenciodinâmica em eletrólito contendo 3,5% NaCl, naturalmente aerado. Quantificou-se, ainda, a porcentagem de ferrita em cada uma das condições através de ataque eletrolítico com solução 20% NaOH. Os resultados obtidos evidenciaram a diminuição desta fase com o aumento do tempo de recozimento, chegando praticamente à sua eliminação com tratamento de 48h. Paralelamente, a resistência à corrosão por pite deste aço foi melhorada de modo proporcional à diminuição da fase ferrita, resultando em um aumento de aproximadamente 115 mV da pior para a melhor condição, comprovando que, de fato, a presença de ferrita-delta prejudica as propriedades de resistência à corrosão localizada.

Aug 7, 2018

By Antonio Favia, Carsten Sowa, Spencer Diehl, Maria Carolina Campos, Christian Green, Marco Tulio, Olaf Schulz

Casting fluxes are one of the key factors to guarantee a good performance of the continuous casting process. Fluxes are added over the liquid steel in the mold, where carbon in the flux reacts with any air present, to form a reducing atmosphere of CO (g) to protect molten steel from oxidation. Then the oxide components form the sintered layer and they melt to form a liquid flux pool. Liquid slag from the pool infiltrates into the mold/strand channel and lubricates the newly-formed, steel shell. It was very common in the past that the addition of casting flux in the mold was made manually by the continuous casting strand operator, where the addition uniformity would mainly depend on the attention of the Operator in process and the addition standard would change from one operator to another, may causing variability on the continuous casting quality parameters. This paper presents improvement of continuous casting parameters such as, stability of flux thickness and reduction of dust in the continuous casting process, with the use of flux distribution mechanism in two continuous casting machines from two different steel plants.

Oct 1, 2019

By Edo Engel

Blast furnace No. 3 at Zaporizhstal in Zaporozhye is rebuilt in 2016-2017. The Ukrainian company is targeting increased production and availability, mainly through the use of new technology. Zaporizhstal awarded a contract for a new Top Charging Unit to Danieli Corus, after comparing all available technologies. Reliability of the chosen charging device is pivotal, since long outages may be required for maintenance/replacement jobs, which strongly affects the availability of the blast furnace. This article describes the Top Charging Unit including DANCU (Danieli Charging Unit) - a robust hydraulic system. The main focus employed by Danieli and Danieli Corus during the development of this system has been availability and maintainability of equipment. This chute type charging unit has only few major moving parts, none of which is complex or vulnerable. The article also describes the main challenges of the project at Zaporizhstal, such as the use of hot sinter.

Oct 30, 2017

By Leonilson Toffoli Pedrini

A corrosão ocorre devido à deterioração de um material pela ação química ou eletroquímica em meio corrosivo, sujeito ou não a esforços mecânicos, causando modificações indesejáveis, tais como perda de massa, alterações estruturais e variações químicas. O aço inoxidável austenítico AISI 304L é utilizado em grande escala pelas indústrias por apresentar baixo custo e boa resistência à corrosão decorrente da camada de passivação. A passividade dos aços inoxidáveis em eletrólito com íons de cloreto é destruída em pontos ou áreas localizadas. Neste trabalho foi analisado, por meio de ensaios eletroquímicos, a resistência à corrosão do aço AISI 304L. Foi utilizada gaiola catódica em chapa de aço inoxidável 316, com dimensões de 0,8 mm de espessura, 112 mm de diâmetro, furos de diâmetro de 25 mm de altura e 8 mm uniformemente distribuída, com um distância de 9,2 mm entre furos. Os tratamentos térmicos foram realizados a 700, 800 e 900ºC, respectivamente. Os resultados indicam que a resistência à corrosão das amostras tratadas diminuiu, devido a precipitação de nitretos quando são submetidas a processos em altas temperaturas.

Aug 16, 2017

By Jan Bak

Rourkela Steel Plant (RSP), which is operated by the Steel Authority of India Limited (SAIL), was inaugurated in 1959 and was the first Integrated Steel Plant in the public sector in India. In 2013, RSP commissioned their No. 5, 4060 m³ Blast Furnace, India's largest. It was built as a turn-key project by a consortium consisting of Danieli Corus and Tata Projects Ltd. and is entirely based on the technology and know-how of Danieli Corus. The new Blast Furnace is the key element of an expansion program that doubles the plant's production capacity and with much of the existing ironmaking capacity reaching the end of its technical and economic life span, it enables RSP to meet existing as well as growing demand for its products. This article discusses how this greenfield Blast Furnace was built in an existing and operating Integrated Steel Plant. It covers the accommodation of land, planning of the new installation to fit the available plot as well as the updated logistical lay-out of the plant. Technical details of the installation are presented, including their consequences for RSP's environmental performance and new perspectives for campaign planning.

Aug 2, 2018

By Luís Carlos da Silva

Vários motivos levaram a priorizarem o uso de fibras naturais em detrimento do uso de fibras sintéticas, sobretudo as razões sociais e ambientais. A fibra deste trabalho é extraída da folha da planta - Furcraea Andina (da Colômbia, onde usam esta fibra para a produção de artesanatos e sacos) e demonstra um grande potencial como reforço de compósitos poliméricos. Este trabalho avaliará o teste de impacto de Izod e Charpy de compósitos com matriz epóxi reforçada com diferentes porcentagens de fibras. Para os testes, as fibras de fique foram misturadas com à resina epóxi em um molde metálico retangular, o conjunto foi submetido a uma pressão e sofreram um processo de cura à temperatura ambiente durante 24 horas. As amostras produzidas foram submetidas aos ensaios seguindo a norma ASTM D256 (Método de Ensaio Padrão para à Determinação da Resistência ao Impacto do Pêndulo Izod para Plásticos) e a norma ASTM D6110 (Método de Ensaio Padrão para Determinar a Resistência ao Impacto Charpy para Plásticos). Os compósitos continham até 30% em volume de fibras de fique, que foram alinhadas ao longo de todo o comprimento da matriz. As amostras submetidas à ambos os ensaios (Izod e Charpy) tiveram suas fraturas analisadas por microscopia eletrônica de varredura (MEV). Houve um aumento significativo da resistência ao impacto de acordo com o aumento da porcentagem volumétrica das fibras de fique. Esse desempenho pode estar associado ao mecanismo de fratura gerado a partir da adesão entre as fibra de fique e a matriz colaborando na absorção da energia de impacto, além do fato de que a fibra é capaz de dificultar a ruptura das amostras.

Oct 30, 2017

By Walter Hartig

Rogesa is operating two medium sized Blast Furnaces, No. 4 and No. 5 at Dillinger integrated steel works plant. The history of the results of the cooling concepts of the intersection between tuyère belt and bosh shows failures at both furnaces. At the 3rd reline of No. 5 Blast Furnace in 2010 changes were made to improve the cooling efficiency of the mentioned area. Two rows of copper cooling plates were installed. After commissioning and a short operating time hot spots occurred in the area of the cooling plates. The decision was taken to develop a new cooling concept together with Paul Wurth Umwelttechnik GmbH, Essen-Germany by replacing the cooling plates by one row of a short copper stave. The duration of the shutdown to perform the work was only 17 days including salamander casting. The operational results after the commissioning are very satisfying with outstanding performance of the new bosh cooling system.

Aug 1, 2018

By Aline Lima da Silva

The reduction in SOFC operating temperature due to recent development in materials and fabrication techniques enables the use of ferritic stainless steels as interconnects for SOFCs. Ferritic stainless steels offer many advantages over traditional ceramic interconnects, such as higher thermal and electronic conductivity, as well as relative ease of fabrication. However, the formation of chromium oxide on ferritic stainless steel results in an increase in ohmic resistance and can lead to the loss of cathode catalytic activity (due to Cr volatilization, with cathode poisoning). The oxide growth depends on several factors, such as steel composition, temperature, oxygen partial pressure. In this way, knowing the phase stability, the oxidation behavior of the material and the oxidation kinetics is of great interest. In this context, a thermodynamic study of the oxidation of ferritic stainless steel 430 under oxidizing atmosphere (cathode), at the temperature of 750ºC, is carried out. As one can see, the thermodynamic system can be very complex, involving several phases (chromium oxide, (Fe,Cr,Mn)3O4 Spinel, iron-chromium oxides, etc.). The effect of oxygen partial pressure and alloying elements on phase distribution is evaluated. Thermodynamic modeling is compared with experimental results from literature.

Aug 8, 2018

By Renan Gurgel Pinho

O objetivo deste trabalho é investigar a esferoidização do aço SAE 1080 e os respectivos efeitos da variação do tempo na microestrutura final e na dureza do material. O aço SAE 1080 foi submetido a recozimento isotérmico, por tempo prolongado, utilizando-se 90, 100 e 120 horas de aquecimento à temperatura de 715ºC. Os resultados mostraram que é possível esferoidizar o aço SAE 1080 nos respectivos tempos escolhidos e perceber aumento da quantidade de esferoiditas, assim como decréscimo na dureza.

Aug 16, 2017

By Alessandro Martinis

The performance requirements for modern steelmaking facilities are ever more stringent, as customers and markets are continuously pushing for technologies which allow having high quality steel produced in an economic and sustainable way. In the details, this paper has the aim to present the excellent results obtained by integrated steel plant where an EAF is fed with high quality hot ENERGIRON DRI. The recent technology developments, combined with the affirmed basic process design, contributed to further maximize the energy of the DRI, reaching the EAF at temperatures above 600°C with a carbon content up to 3.5%, as confirmed by plant data. These improved input material characteristics resulted in reduced electrical energy consumption and increased liquid steel production.

Aug 16, 2017

By Luiz Alberto dos Santos

. In this work, samples of the alloy with composition of 50.9 % at. Ni were machined and were subjected to hot tensile test, after the machining all the samples were solubilized so that all were in the same condition during the hot tensile test. The hot tensile tests were performed between the temperatures 350-650°C and the yield stress were between 800 and 597.1 MPa and area reduction between 17 and 75% with respect to the initial area. The test at 350°C shows a fragile fracture characteristic while the hot tensile test above this temperature showed a predominantly ductile fracture. The fragile fracture is evidenced by the river marks that are characteristic of this type of fracture, because in this condition does not promote much plastic deformation. The higher temperatures present ductile fracture, because present the dimples that also characterize this type of fracture. This work shows the temperature relationship in the mechanical properties, more specifically the hot tensile test, in the NiTi alloy.

Oct 30, 2017

By Renan Oss Giacomelli

The adhesion of multifunctional coatings on soft substrates is of paramount importance in the tribological behavior of this important class of surface treatment. In particular, scratch and indentation tests have been extensively used in order to assess this property. In this paper, the adhesion of a-C:H diamond-like carbon films deposited on nitrided low carbon steel was evaluated by indentation and scratch tests. The coatings were produced by PECVD onto 1020 steel substrates with two different surface finishing: ground (Sq = 0.184 µm) and polished (Sq = 0.002 µm). Indentation tests using a Rockwell diamond indenter were conducted and the adhesion evaluated by measuring the spalling region on images obtained by using optical microscopy. The analysis of the spalling regions produced semi-quantitative results, eliminating the subjective qualitative analysis proposed by the standard method VDI 3198. In addition, scratch tests were performed using the same indenter and a comparison between the two techniques was established.

Jul 31, 2018

By Andrew Salach

Experimento laboratorial avalia desgaste em rodas e trilhos de PR’s. Chegou-se a conclusão de que rodas com elevada dureza economizam desgaste de rodas e de trilhos.

Aug 16, 2017

By Larissa Agrizzi Ronqueti

The effect of coiling temperature on selective oxidation behaviour of binary and ternary iron-based model alloys containing different contents of Si or Mn were investigated by SEM and SIMS. The experiments were carried out with a temperature ranging from 450 °C to 700 °C, under N2-5%H2 gas flow with a Dew Point of -3.3°C, for different durations. SEM images of binary iron-based model alloys revealed a decrease of grain boundary oxidation depth with increasing Silicon or Manganese content. At 530°C and 600°C SIMS results showed no Silicon diffusion toward surface, contrary to the results analyzed for Fe-x%Mn. Tests results and Wagner’s theory application (specific cases Fe-0.2%Si and Fe-0.5%Si) showed that grain boundary oxygen diffusion coefficient “DoGB” is almost 60 to 70 times faster than oxygen bulk diffusion coefficient. These results helped to broaden knowledge of single-element effects on grain boundary oxidation, in addition, will contribute of the future works in new steels with complex alloy compositions.

Aug 17, 2017