Search Documents

The 103rd Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 16th August, 2000. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past Presidents, our Members and other guests, among them the following: Reinie Meyer, President, The Geological Society of South Africa Dr Nielen van der Merwe, Chairman, The South African Institute of Rock Engineering Chris Fourie, President, Institute of Mine Surveyors of South Africa

Jan 1, 2001

By Joel Nonnweiler, Rafael Castro, Ross Webb

The three thousand foot long 66-inch diameter Folsom East Interceptor Section2B was completed accident free, on time and under budget with no measurable surface settlement. The tunnel passed through nested cobbles, highly abrasive sands and gravels, and abandoned mine workings with less than five-feet of cover at times. Preventing settlement was critical since the tunnel passed under a heavily traveled state highway. A pilot project to test microtunneling and pipejacking methods in the same ground conditions abandoned both drives before completing the planned drive lengths. This paper discusses performance of the conventional tunneling method selected to excavate the ground and the effectiveness of the ground modification techniques employed.

Jan 1, 2001

By W. G. Davenport

The flash furnace is used for smelting concentrate to (i) high-Cu matte and (ii) molten metallic copper. It is also used for converting solidified/crushed matte to molten metallic copper. This is flash converting. It consists (Table 20.1, Fig. 20.1) of: (a)tapping molten 65 to 72% Cu matte from a flash smelting furnace (b) granulating the molten matte to ?1/2 mm particles in a 103 m3/hour water torrent (c) crushing the granulated matte to 50 µm in a vertical roller mill (d)drying the crushed matte (e) feeding the dry particulate matte to a second flash furnace for oxidation converting to molten copper. In 2000, flash converting is being used by Kennecott Utah Copper (George, et al; 1995; Newman et al, 1998, 1999a,b). A second installation is being designed for the Chuquicamata smelter (www.outokumpu.com [October 12, 2000]), The potential uses of flash converting are: (a) as the second half of a flash smelting/flash converting coppermaking sequence (b) as a continuous converting alternative to batch submerged tuyere converting. This chapter uses our flash furnace matrix to determine the %O2-in-blast, industrial oxygen and oil requirements for converting solidified 65% and 72% Cu matte to molten copper. It then discusses choice of feed matte grade and other aspects of the process.

Jan 1, 2001

By A B. Christie, S C. Cox

Effective land-use planning requires accurate knowledge of mineral resource potential. Mineral companies during reconnaissance exploration, feasibility investigations and mine development also use this type of analysis. The Institute of Geological and Nuclear Sciences is undertaking a two-year project reviewing the resource potential of the West Coast of the South Island of New Zealand. Spatial prospectivity models have been developed as part of this resource assessment process, using computer based statistical pattern recognition techniques to delineate areas that are prospective for mineral deposits and to test deposit genesis models. Digital GIS data-sets of mineral occurrence were correlated against geology and exploration information. The distribution of mesotherrnal shear zone gold deposits in the Reefton Goldfield, were examined against geological data-sets from both the regional (QMAP) and local prospect-scale mapping. Weights of evidence analysis generated a correlation matrix that highlights relationships and degrees of association that might otherwise not normally be recognised.   Mesothermal shear zone gold deposits have strong positive spatial correlations with Greenland Group host rocks and areas with moderate to high quartz vein densities; moderate-strong positive correlation with regions <500 m from folds, with regions <600 m from faults and five to eight kilometres from granite contacts; moderate correlations with Ntrending fault and fold segments; and no/weak/poor correlations with fault intersections, fold-fault intersections, bends in regional structures and magnetic and radiometric data. The regional and prospect scale data sets give different results, with the more detailed prospect scale mapping giving generally better correlations. This emphasises the value of detailed geological mapping in the exploration process.   Maps generated by prospectivity modelling consistently highlighted areas of known mineralisation and generate targets where follow-up investigation is warranted. The prospectivity per unit area provides a measurable value that should change as new information comes to hand and, in addition to highlighting targets, can be used to measure the impact of increased exploration expenditure and assess the effectiveness of exploration investment.

Jan 1, 2001

Elongates are commonly used as stope support in South African gold and platinum mines. To evaluate the effect of the inherent strength, stiffness and yield variability associated with elongates, a statistical method is presented which addresses and quantifies the support performance at various levels of certainty. The analysis, which is based on a normal distribution, makes use of force-deformation curves determined from multiple laboratory compression tests on the same support type. The applicability of the method is illustrated making use of actual performance capabilities of various types of elongates. In order to ensure a high probability that support units installed underground exceed the standard support performance curve established by means of laboratory tests, the statistical mean of a suite of tests based on the same support type is downgraded. The ?correction factor? is a function of the mean and standard deviation of the test data, as well as the sample size of units deemed to control the local rock mass stability. It is shown that downgraded performance curves based on a high probability (90 to 95percent) of support units exceeding this performance level are suitable to ensure that the design of support systems will in variably meet the design criteria. In the highly discontinuous hangingwall rock mass typically associated with intermediate- and deep-level mining operations, the interaction between adjacent support units is comparatively limited (at the support spacings commonly used). Therefore, the appropriate sample size (n) of the support units controlling the local rock mass stability should be n= 1. In shallow mining conditions, sample sizes of up to n=5 may be warranted, depending on the spacing of joints and other discontinuities in the hangingwall.

Jan 1, 2001

By B. M. Nyombolo

The interest shown in our paper by Drs Schaekers and Dew, and their favourable comments, are appreciated. However, some of their remarks require a response. Stability testing procedures Regarding the issue of stability-testing procedures, we concur that no long-term procedure has been accepted by either environmentalists or the mining/processing industry as a valid method to test the long-term stability of solid wastes. We agree that the method we used is no exception, and we certainly did not claim that it should be recognized as such. What we did attempt to portray was that we had designed the test procedure in an attempt to simulate, at a very small scale, a tailings dam environment.

Jan 1, 2001

By R. J. Snoby, J. K. Alderman

Although once fairly common as a method of coal preparation in the United States, dry cleaning has virtually disappeared. Low-rank coals used for power generation in the western U.S. are suited for dry cleaning because water has limited availability in the American west. Surface moisture added through wet cleaning offsets energy improvement achieved from mineral matter reduction. Information will be presented on the commercial application of dry cleaning in North America, the historic development and current status of the technology, and the introduction of modern processing theory and control technology to the design of dry cleaning equipment and plants.

Jan 1, 2001

By B. Weyerman

U. S. Steel's Oak Grove Mine experienced several top hinge failures on their caving shields. It was determined that all the caving shields needed to be replaced with new caving shields before more thilures occurred. The cost and amount of time needed for several scenarios of caving shield change outs were compared. This paper discusses how Oak Grove Mine decided to and did change 126 caving shields in six specially designed jig stations underground during a longwall move using their own UMWA employees.

Jan 1, 2001

In exploiting the ultra-deep, narrow reef ore bodies of the Witwatersrand, the ventilation and cooling systems within the stopes play a critical role because of high concentrations of active workers. This paper examines the heat, ventilation and cooling effects of a number of different stoping layouts for narrow reef mining in ultra-deep operations in very hot rock. The stope ventilation and cooling needs are driven primarily by the difference between the air temperature and that of the rock front being excavated. These needs depend on the face utilization, geometry, face advance (rate and direction), layout, backfill, use of water and machinery1,2,3. Detailed studies of different stoping configurations have been undertaken for mining operations extending to depths of 5000m below surface, where virgin rock temperatures approach 70°C. Extensive work has been completed with regard to evaluating ventilation and cooling requirements to maintain air reject temperatures of 28°C wet-bulb and better. This knowledge is being used to determine overall cooling requirements, reduce operational costs and maximize the efficiency of cooling systems. These issues are important when considering both the local and regional air conditioning systems and the most effective application of in-stope chilled water.

Jan 1, 2001

By Gordon Revey

The challenge of managing blasting risk, types of risk, public perception, and a system for managing risk were covered in the first part of this article in the May/June 2000 issue of the Journal of Explosives Engineering. This final part of this two-part series provides a method for identifying specific blasting risks and reviews the importance of community relations.

Jan 1, 2001

By S. Lähteenmäki, P. Koivistoinen, J. Levanaho

Semi Autogenous Grinding (SAG) circuit is the most common grinding circuit to day. In Europe and South Africa fully autogenous (AG) circuits are also popular. SAG circuit has a lower capital cost and simple operation. SAG circuit requires the use of grinding balls, which increases operating costs and decreases availability. An AG circuit may produce a higher Net Present Value to the investment. The AG circuit is more complex to design and operate. However, operating experience from AG circuits illustrates that an AG circuit can be as trouble free as a SAG circuit with the benefit of lower operating cost.

Jan 1, 2001

By Chris Larsen, Ian Orford, Mike Cooper

"An autogenous grinding circuit was commissioned at the Brunswick concentrator in October 1998. The autogenous grinding circuit replaced existing surface crushing plants, fine ore storage, rod and primary ball mills. The 8.54m diameter x 4.27m long (EGL) AN1 mill is driven by a bidirectional variable speed 6.3MW ABB wound rotor motor with Slip Energy Recovery (SER) drive. The AG mill was subsequently converted to SAG operation in May 1999 for a number of reasons. The mill is operated in closed circuit with horizontally inclined 660mm diameter cyclones to produce a circuit product P80 of 85 microns. Extensive test work and JKSimMet design modeling resulted in a production circuit operating closely within design expectations.The circuit is highly instrumented and controlled via a hybrid Programmable Logic Controller (PLC-5) and Fisher PROVOX Distributed Control System (DCS) that is in communication with the property information highway. An expert control system (Gensym G2) is used for control of the SAG mill load.Engineering and construction were completed in 28 months from the time of management approval for the project. The Brunswick AG/SAG mill circuit was commissioned on schedule at the $M 23.5 forecast budget."

Jan 1, 2001

By Raymond Chenier

British Columbia (BC) is Canada’s most western province. The landscape in BC is amongst the most beautiful and pristine in the world. Along with its beauty come vast mountain ranges, coastal rain forests, swamplands, deep river valleys, and almost every type of landscape imaginable. These all have, or at one time had, logging roads constructed. Some of these areas should never have had roads constructed due to poor drainage and unstable slopes, but some of the roads could be considered engineering masterpieces. To navigate a vehicle the size of an off-road logging truck down the side of a mountain with an 80°h side slope or greater can be a hair-raising experience. Not to mention coastal rains and/or high elevation blizzards. These factors collectively make logging BC’s most hazardous occupation. People are seriously hurt, sometimes even killed everyday.

Jan 1, 2001

By Lindsay Wade, Peter Dare-Bryan

Benches in surface mines often contain known areas of ore and known areas of waste, which must be mined selectively. When rock is blasted it not only fragments but is also physically, and non-uniformly, moved. Risks therefore exist of ore being lost if treated as waste and of mill feed being diluted by waste. Both possibilities carry serious fmancial implications.

Jan 1, 2001

By D N. B Skinner, R L. Brathwaite, M S. Rattenbury

The Institute of Geological and Nuclear Sciences Ltd has carried out a mineral resource assessment of the Coromandel region, one of the most mineral-rich regions of New Zealand. The assessment focussed on metallic minerals and clays, because these are the main commodities that have potential for increased production and export from the region (and from New Zealand).   Three steps were used in the assessment: 1) development of mineral deposit models, 2) comparison of the models with regional geology, structure, geochemistry and past mineral production to estimate the number of undiscovered mineral deposits, and 3) application of grade-tonnage models to determine the quantity and value of the known and undiscovered resources. In step 1, descriptive and grade-tonnage mineral deposit models were developed for 11 different types of mineral deposits: ò     Low-sulphidation andesite-hosted epithermal Au-Ag ò     Low-sulphidation rhyolite-hosted epithermal Au-Ag ò     High-sulphidation quartz-alunite epithermal Au ò     Porphyry Cu-Au-Mo ò     Andesite-hosted polymetallic veins adjacent to mineralised porphyry stocks ò     Zn-Pb-Ag skarn ò     Cu-Ag skarn ò     Hot spring Hg ò     Shoreline placer Ti ò     Rhyolite-hosted halloysite clay ò     Volcanic-related kaolinite clay   Step 2 was aided by a geographic information system (GIS) assembled from a number of digital spatial data sets including: a digital elevation model, an aeromagnetic map (from open file mining company data), a geological map (from the GNS QMAP project), location of areas of hydrothermal alteration, locations of mineral deposits (from the GERM database), stream sediment geochemical analyses (from the REGCHEM database), and a lineament map derived from satellite remote sensing data and the digital elevation model.   Based on May 2001 commodity prices, potential resources estimated for the 11 mineral deposit and grade-tonnage models total NZ$22 806 million for the metallic minerals, NZ$1000 million for halloysite clay deposits and NZ$57 million for kaolinite clay deposits.

Jan 1, 2001

By Richard W. Hanford

The geotechnical construction industry generally considers soil mixing to be defined as an in situ ground improvement or treatment method by which a dry or wet reagent is introduced into the ground and is blended with the soil by mechanical or rotary mixing tools. This results in relatively homogenous mixtures whose engineering properties are improved and are greater than the soil properties before mixing. Reagents usually include cement, but may also include processed clay such as bentonite, when a reduction in hydraulic conductivity is desired, or other proprietary chemicals when chemical stabilization is the objective. Mixing may be either shallow or deep. Shallow Mixing is the term arbitrarily used for treatment of soils within the upper 30 feet; Deep Mixing denotes treatment below 30 feet to the depth limits of the equipment. Mixing equipment may consist of single or multiple-shaft tools having cutting and mixing blades of many different configurations. To avoid using proprietary nomenclature, reference to Shallow Mixing Methods (SMM) and Deep Mixing Methods (DMM) are the preferred terms. Although originally developed and patented in the United States in 1956, in situ construction using various soil mixing methods is more prevalent in Japan and the Scandinavian countries. Reintroduced into the United States from Japan in 1986 for ground improvement and liquefaction mitigation at Jackson Lake Dam, Wyoming, acceptance of soil mixing methods has been gradual but slow. Applications typically include:

Jan 1, 2001

By M. Irish, M. Jahraus

Accurate prediction of gold (or other metal) production from a heap leach operation is essential to the economic vitality of any such operation. However, this is also one of the most challenging issues facing managers of these facilities. Three approaches to modeling gold production from the Valley Leach Facility (VLF) at Anglogold’s Cripple Creek & Victor Gold Mining Company are presented. Evolution of these modeling methods has been necessary as ore heights and volumes have increased. In addition, the complex geometry of the VLF presents additional complications to production modeling, Comparison of actual and predicted gold production are presented

Jan 1, 2001

By Donald Leroux, Ralph Dahlke, Dave Scott, Finch. James A., Cesar O. Gomez

"The efficiency of the flotation process depends on how effectively air is dispersed into small bubbles. Bubble surface area flux - the surface area of bubbles per unit time per unit cross-section area of a cell - is emerging as the parameter to characterize gas dispersion. One of the approaches proposed to measure bubble surface area flux in industrial cells is based on the measurement of two variables: gas velocity and gas holdup, using separate sensors. Plant testing of the gas velocity sensor gave evidence of a series of operational problems which may be necessary to correct before attempting to characterize gas dispersion. Problems such as uneven air distribution within a cell and along a bank, faulty air and slurry valves detected during attempts to redistribute air, and poor control of pulp level and gas flow became evident. Detection of these problems from gas velocity measurements is illustrated.INTRODUCTIONBubble surface area flux is considered a key variable in the optimization of flotation circuit performance (Gorain et al., 1997; 1998). The Mineral Processing Group at McGill University has devised and developed a method for estimating bubble surface area flux in industrial flotation cells (Finch et al., 1999). The method is based on measuring gas holdup and superficial gas velocity using two separate sensors and applying drift flux analysis to estimate bubble size (Dobby et al., 1988; Banisi and Finch, 1994). With bubble size and superficial gas velocity known bubble surface area flux can be calculated.This method was selected by Noranda to characterize gas dispersion in cells as part of a program to model and optimize flotation circuit performance. However, initial testing at Brunswick Mine with the gas velocity sensor provided some unexpected results indicating operational problems and equipment malfunctions that needed to be addressed before systematic measurement of gas dispersion could be initiated.The subject of this communication is to illustrate the detection of these problems from gas velocity measurements. The line 3 Zn Cleaner circuit comprising four stages of Denver DR cells was the main subject of analysis, including the effect of correcting these problems on the metallurgical performance of the Zn 3rd cleaner bank of ten DRl 00 cells."

Jan 1, 2001

By M. El Ganaoui, P. Bontoux

"A computational model to investigate solid/liquid phase change transitions for binary alloy under directional solidification is presented. Conservation equations are developed by using an homogeneous formulation. A second order accuracy method of time and space based on finite volume approximation has been evaluated by comparing results to spectral solution for time-dependent solutal convection developping in a melted alloy. For extended model to solid/liquid interface effects time amplification of solutal perturbation injected near the interface is described before considering solutal convection is melt.IntroductionThe enthalpy method gives a front fixing approach for energy equation without introducing coordinate transformation. The interfare position is recovered a posteriori [1]. A number of authors have extended this approach so as to include the convection phenomena within the two phase 'mushy region' [2, 3, 4, 5, 6].We have developed a time-dependent enthalpy-porosity formulation for directional solidification [4, 6, 8]. The interaction between solid and liquid phases is modelised by a Darcien type force in the phase change area. The behaviour of the melt is similar with the flow of an incompressible fluid in a porous medium. This force is proportional to the relative phase velocity. It corresponds to a damping force depending on the anisotropic permeability of the 'mushy zone'. The permeability depends on the liquid fraction and on the size of·solidification microstructures. An informative discussion of a new slant on the general approach of continuum mechanics needed to analyze the formation of mushy zone is given in [12]. The method is extended to the presence of species diffusion: the solutal Stefan condition which expresses the solute incorporation or rejection across the interface is accounted implicitly in a species equation valid in all the domain [14, 15]."

Jan 1, 2001

By Lawrie Logan, Mike Wiggin

This paper will be in two parts, a discussion of the benefits available from benefit sharing as a concept followed by an examination of how this approach was applied at Mesa J Mine and what improvements were made. The first part is an outline of the ways that both parties in a benefit sharing agreement can uncover additional wealth by bringing a new approach to the relationships between mine and supplier. The paper describes a partnering agreement recently established between Robe River Iron Associates (RRIA) and Dyno Nobel Asia Pacific Ltd (DNAP) to access the wealth locked up by the usual explosives supply contracts in Australia and elsewhere. The partners are acting cooperatively to maximise the benefits to both parties from optimising blasting practices at the Mesa J Iron Ore Mine in the Pilbara region of Western Australia.

Jan 1, 2001