Search Documents

Wet mining of auriferous gravels at L & MÆs Waikaka operation in Southland creates spoil dumps derived from stripping of a clay rich overburden, tailings from past dredging and the processing of auriferous sands and gravels. Over recent times, spoil dumps have slumped on six occasions, threatening the viability of the wet mining operation. Close examination of slump morphology, coupled with the sequence of material placement and rate of dumping suggested a mechanism associated with undrained failure of a 2 m layer of silt and sand tails forming the base of dumps.Commencing with some information on the geotechnical properties of source overburden, back analysis of failure morphology and sequence and development of undrained loading conditions from first principals, the most likely failure mechanism and factors controlling failure were defined. Based on analysis results, a scheme to stabilise the lowwall dumps was developed and implemented, augmented by continuous monitoring of pore pressures in the basal wet tails, and laboratory testing for confirmation of computed material properties.Lowwall spoil stability has improved since implementation involving changes to the method of spoil loading, and modification of wet tails composition to improve permeability and drainage of the basal wet tails under load. The method and approach to prediction and verification of failure mechanism provide a sound basis for continued mining of deeper auriferous gravels.

Jan 1, 2002

By R. Altindag

The rock brittleness is one of the most important rock properties that affect the drill-ability of rocks. It is supposed that the increase in rock brittleness causes the increase in penetration rate. The drill-ability of rocks depends on many factors. These factors can be separated as two parts depending on a machine, bit type, rotational speed, thrust, blow frequency, flushing, and rock properties, brittleness, compressive strength, structure, hardness, etc. In this paper, the relationship between brittleness and drill-ability index, which is used in the prediction analysis of the penetration rate of rotary blast hole drills, were examined using regression analysis. It is also seen that significant correlations exist between brittleness and the drill-ability index.

Jan 1, 2002

By B. Samoski

In late 1994, EPA and OSM acknowledged that efforts by any one agency or by the many different agencies to remedy the water quality impacts of decades of contamination from abandoned coal mine lands in Appalachia would not be successful if their disjointed efforts were not unified and if the local watershed organizations were not included. The result of the collaboration between EPA and OSM was the creation of a statement of mutual intent which was a pledge by government agencies, watershed organizations, and the industry to restore watersheds degraded by acid mine drainage from abandoned coal. The presenter will describe the evolution of this pledge from a paper promise to on-the-ground remediation projects.

Jan 1, 2002

By Wes Bender

Considering the current interest in Global Positioning System (GPS) usage, it might be timely to look at a more efficient means of utilizing these instruments. The GPS system currently utilizes 28 satellites (4 are spares) circling the earth in an inclined orbit. Normally at least six satellites are within your area of reception at any given time. The satellites broadcast an extremely accurate time signal and an almanac containing all the satellites’ orbital data. This information is updated regularly as the satellites circle the earth. Your GPS receiver, once it has picked up one satellite’s broadcast, can then determine which other satellites should be available for plotting.

Jan 1, 2002

By Jacques Ouellet, Ferri Hassani

"Within the mining industry paste backfill technology has evolved over the last two decades. This technology aims at producing safe and cost effective backfill of high strength. When used as cemented backfill underground the usual practice in the mining operations was to consider the backfill as a component under the production engineer responsibility. With its growing use in various site conditions some problems were encountered. Over time the mechanical characteristics of paste backfill could deteriorate. Investigations on these problems brought an increased understanding of paste backfill chemistry. Effectively, paste backfill is produced with tailings slurry having sometimes very complex chemistry and mineralogy. The bonding agents can be sensitive to the chemistry of these slurries. Today, a new understanding of the complex chemical reactions involved in cementing paste backfill is derived from concrete research literature. Cemented paste backfill is a manufactured product and as thus all steps involved in its making must be looked at. Both the processing engineers and mining engineers need to be involved. The proposed paper will go over the various developments and new understanding gained over the years on paste backfill chemistry. The authors had the opportunity to work with various Canadian mines that implemented paste backfill in their operations. Chemical alterations case study will serve to illustrate the importance of a good understanding of cement and paste chemistry. The authors will then conclude on research orientations needed to bring a more efficient use of paste backfill technology. The crucial role of the processing engineers in the paste backfill manufacturing will be discussed.INTRODUCTIONPaste backfill is usually prepared from a mixture of solids and water containing at least 15% particles smaller than 20 microns with the addition of binders for mechanical strength. Historically, tailings had been classified to extract the fines and only the coarse part was placed underground as sand slurry. Paste fill was researched in the last three decades to enable mining operations to use all the tailings, including fines, in backfill. The outcome of the early studies showed that paste fill provides high strength but due to preparation complexities and transportation problems is expensive. A greater understanding of the transportation mechanisms and advances in dewatering technology in recent years has resulted in more practical use of paste backfill."

Jan 1, 2002

By Dan Brown

Two drilled shaft foundations were subjected to axial load tests in order to measure the influence of drilling fluid on performance. Other than the differing drilling fluids, the shafts were constructed with great care to ensure identical conditions. The results indicate superior performance in both side shear and base resistance of the shaft constructed using a polymer over that of the shaft constructed using bentonite drilling slurry.

Jan 1, 2002

By Chris D. Thompson

In Southern Ontario, Canada, piles are frequently driven through competent clayey soils to obtain end bearing on extremely dense till or bedrock. One reason for this is the difficulty at assessing the adhesion of the clayey soils. This is illustrated by texts, such as the Canadian Foundation Engineering Manual, which is the standard of practice in Canada, that indicate that theoretical analysis of the adhesion values of such soils are unreliable. In this paper, the results of high strain dynamic testing have been used to estimate the shaft resistance of 11 closed end pipe piles driven in overconsolidated very stiff to hard clayey tills at four sites by means of the CAPWAP wave equation analysis. More than twenty-five years of experience with bearing capacity predictions by such means have developed considerable confidence in its accuracy. The results were found to correlate reasonably with the average Standard Penetration Resistances of the clays at the sites. There was a linear relationship between an adhesion of 64 kPa at 20 blows per 300 mm and 192 kPa at 60 blows per 300 mm. At one site, 6 piles were tested and found to have a wide range of Standard Penetration Resistance and estimated adhesion in the same stratum. While there was significant scatter of the results, piles would have been safe at design loads obtained from the relationships established by the analysis carried out for this paper after applying appropriate factors of safety.

Jan 1, 2002

By G. A. Kordosky

The concept of selectively extracting copper from a low-grade dump leach solution followed by stripping the copper into an acid solution from which electrowon copper cathodes could be produced occurred to the Minerals Group of General Mills in the early 1960s.This simple, elegant idea has resulted in a technology by which about 2.2 million tonnes of high quality copper cathode was produced in year 2000. The growth of this technology is traced overtime with a discussion of the key plants, the key people and the important advances in leaching, plant design, reagents and electrowinning that have contributed to the growth of this technology. Some thoughts on potential further advances in the technology are also given.

Jan 1, 2002

By N. Abdel-Khalek, A. Youssef

The tailings from beneficiation of Florida phosphate ore contain considerable phosphate values. These tailings are currently discharged into large disposal areas. More than three million tons of P2O5 are discarded with the phosphatic slimes (clays) in Florida each year. These phosphatic clays not only create one of the most difficult disposal problems in the mining industry, but also represent a tremendous loss of P2O5. As the quality and quantity of Florida’s phosphate reserves diminish, recovery of phosphate values from these wastes becomes more vital. This will also significantly lengthen the life of these important phosphate resources. Thus, it is the goal of this study is to recover more than 80% of the phosphate values in phosphatic clays. A systematic study to characterize samples taken from inactive disposal area has been conducted. The data suggest that natural segregation takes place in the settling pond. In other words, coarser particles settle closer to the feeding point of the pond. Flotation tests were conducted using the +325 mesh fraction of samples obtained from sites close to the feeding point (sample# A) and further from that point (sample# B) and (sample# C) which is even further away from the feeding point. The results show the following: Sample# A gives the highest grade and recovery, followed by that of # B and then of # C. There is a great potential to upgrade sample# A where concentrates of high grade (68.9-70.1 % BPL or 31.5- 32.1% P2O5) and recovery (~86.6-95.4 %) can be obtained under the investigated operating conditions (1.0 – 2.0 kg/ton sodium silicate and 1.5—3.0 kg/ton collector mixture of fatty acid and fuel oil). The mineralogical and chemical analysis of all samples is presented in this paper for comparison. Only in this paper, the flotation data of (site # A) are discussed below.

Jan 1, 2002

By T Howard, J E. Everett

BHP Billiton Iron Ore has replaced the conventional product quality control batch system at Yandi with the Continuous Stockpile Management System (CSMS) centred on a fully integrated æcontinuousÆ stockpile flow from mine planning through to port reclaiming. With increasing tonnage rates, tight operational coupling associated with the original batch system caused production interference which achieved final product quality but in an increasingly inefficient manner. This innovative approach places a continuous emphasis on product grade control and takes full advantage of the most appropriate blending opportunities of the mine to port planning and production system in order to reduce the natural variability of the ore to an acceptable level. To implement continuous control, product variability throughout the process is classified as long-term and short-term. Long-term variability is best controlled through the monthly mine planning process which determines monthly grade targets while taking into account optimum mine development. In the past, attempts to control long-term variability were made at the port through selective stockpiling and reclaiming which reduced operational efficiency. Short-term variability is best controlled around the monthly mine grade target by daily mine production scheduling, train sequencing, stacking into port stockpiles of appropriate size and systematical stockpile reclaiming. The implementation of the new system has maintained customer accepted shipping grades and has provided significant improvements in resource utilisation, operational efficiencies and costs.

Jan 1, 2002

By V. Bush, T. G. Killingsworth, E. P. Ruffel

Effective and sustained corporate energy management programs are becoming a necessity for energy users as electricity deregulation laws are enacted on a state-by-state basis across the country and environmental regulations pertaining to emissions become more prevalent. The “Total Energy Asset Management” (TEAM) approach has been developed to assist energy end users with the development and implementation of corporate energy management programs designed to reduce energy risks and increase energy cost savings. This paper highlights the ways in which this approach can be applied to the mining industry while minimizing initial program implementation costs and increasing potential program benefits. Nearly the entire mining industry has become very focused on identifying opportunities to reduce costs per unit of yield. The industry as a whole has increasingly faced pricing pressures in large part due to the effects of global competition. The result of international marketplace participation and the emergence of higher efficiency recovery techniques have resulted in flat or even decreased prices for mining products. Thus, opportunities to reduce costs are actually opportunities to gain a competitive edge over similar mining operations. Due to the energy-intensive nature of many mining operations, the costs associated with energy are often a substantial percentage of operating costs. Therefore, it becomes very important to develop the corporate mentality that energy is an asset whose use should be optimized globally. In addition to the cost benefits of the TEAM approach, other benefits may occur such as reductions in facility greenhouse gas emissions.

Jan 1, 2002

By P J. Mienie

The Palaeo-Proterozoic Transvaal Supergroup in the Northern Cape Province of South Africa is host to the largest known resources of high-grade hematite ore on the Southern African continent. These ores are currently being exploited at Sishen and Beeshoek. Hematite occurances on the Sishen South exploration project (some 65 km south of Sishen mine), are at present the focus of an intensive investigation. At both the Sishen and Sishen South deposits, mineralisation is found within lithologies belonging to the Transvaal and Oliphantshoek Supergroups. The Transvaal Supergroup comprises a basal, carbonate platform sequence (the Campbell Rand Subgroup) overlain by thick units of banded iron-formation belonging to the Asbestos Hills Subgroup. The Asbestos Hills Subgroup is unconformably overlain by sedimentary rocks of the Gamagara Subgroup. The latter Subgroup has been correlated with the lowermost unit of the Oliphantshoek Supergroup. The Sishen and Sishen South deposits are located close to the western margin of the Kaapvaal craton and have been subjected to intensive, structural deformation. Both localities have undergone folding, faulting and thrusting. Early regional tectonism (2400 - 1700 Ma) played a critical role in the genesis and preservation of the ores from younger erosive events. At both deposits, four similar iron ore occurrences have been recognised. The ores have developed in specific depositional environments and hence display unique physical, chemical and metallurgical properties:The bulk of the high-grade hematite comprises laminated and massive ores, which are found in the upper parts of the Asbestos Hills Subgroup. The laminated and massive ores are best developed in basinal and pseudo-graben structures. Collapse breccia ores of medium- and lower-grade are preserved within deep palaeosinkholes. The sinkholes have developed within the dolomites of the Campbellrand Subgroup. Lower-grade conglomeratic and gritty ores constitute the remainder of the deposits. These ores are found in the overlying clastic succession of conglomerates, shales and quartzites belonging to the Gamagara Subgroup. Although, there are many stratigraphic and lithological similarities between the Sishen and Sishen South deposits, there are also important differences, which will impact on the profitable exploitation of the ores. The most striking contrast between the deposits is their size and geometry. Sishen mine is a single pit operation with an opencast mineable reserve of 895 Mt. The Sishen orebody is thicker, more continous and significantly larger than the Sishen South deposit. The Sishen South deposit has a potential opencast reserve of 228 Mt. It comprises a number of small and narrow, isolated orebodies, spread over an area of ¦64 km2 . There is a significant difference in grade between the deposits. On average the orebodies of the Sishen South deposit have a higher iron content (+0.25 per cent Fe), less potassium (- 0.090 per cent K2O) and less phosphorus (-0.019 per cent P). The Sishen South deposit has less interbedded shale in the laminated and massive ores. The footwall of these high-grade ores is a light-density, intrusive sill, compared to banded iron-formation at Sishen. With a proposed heavy-medium separation plant at Sishen South, the impact of dilution on product grades is expected to be less than that currently experienced at Sishen.

Jan 1, 2002

Platiniferous horizons such as the Merensky Reef that are mined chiefly for their PGE contents constitute one end member of a continuum of Ni-Cu-PGE sulfide deposits; Ni-(Cu) sulfide deposits in which the PGE may or may not be by-products represent the other end of this continuum. Although it has long been thought that PGE-rich sulfides can only be developed by magma mixing in large magma chambers, new PGE data for the Bushveld Complex suggests an alternate model to account for origin of mineralization in the worldÆs most important Pt producer. Briefly, this model suggests that PGE-rich sulfides were initially deposited at depth below the Bushveld Complex as a result of interaction of a S-undersaturated mantle magma with S-rich crustal rocks. These PGE-rich sulfides were subsequently re-dissolved by a second magma, which introduced the PGE into the Bushveld Complex magma chamber, where the PGE-rich reefs were formed due to cooling of these magmas. If this model is correct, it means that large layered mafic/ultramafic intrusions are not a prerequisite for the formation of economic PGE-rich deposits. Exploration for Merensky Reef-type PGE deposits can be greatly facilitated by documenting variations in the background PGE contents of non-mineralized rocks collected on traverses across mafic/ultramafic intrusions; the mineralized horizons occur at cross-overs in ratios such as Pd/Cu, Pd/Se and Pd/S.

Jan 1, 2002

By Eric Zahl

Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, Spokane, WA, have collaborated with three Western longwall coal mines in an ongoing effort to develop technologies that will aid in providing safe and stable working areas. The goal of the research described here is to develop a stress monitoring system that will provide immediate information to mine managers for making daily safety decisions as areas of poor ground are mined through. Initial work has focused on answering preliminary questions regarding the reliability and use of stress change patterns. Research is concentrated on monitoring horizontal stress because horizontal stress is transmitted over long distances through stiff strata, thus allowing an extended length of entry to be monitored. This paper presents an explanation of the concept, key results from field tests at two mine sites, and a proposed process for imple¬menting a monitoring system. System design layouts, instrument use, data collection and interpretation methods, and processes to present findings to mine staff are described. Additional validation and correlation with actual failure mechanisms are required before this approach can be recommended at ongoing operations. How¬ever, initial results indicate that this approach shows promise in mines prone to bumps and roof falls associated with large stress changes. In particular, analyses of measured changes in horizontal stresses appear useful.

Jan 1, 2002

The Golden Cross project was a joint venture between Coeur NZ Ltd (80 per cent) and Viking Mining Company (20 per cent). The site is located in the Waitekauri Valley, 8 km north-west of Waihi, on the Coromandel Peninsula, in the North Island. The mine-site is situated close to the Coromandel Range Divide between the headwaters of the Waitekauri River and the Martoto Stream. The site has a history of Gold Mining dating back to 1892. The more recent mine comprised an open pit and underground gold and silver operation from December 1991 to April 1998, MacGillivray, Maton and Goldstone (2000).Doug Hood Ltd commenced the first of three contracts on site in September 1997 and was responsible for completing the final stages of open pit mining, landslide remedial works mine closure and rehabilitation works. The Mill Closure and Rehabilitation and Drainage Works contract, for which this submission relates, commenced in September 1999 and was officially completed by Doug Hood Ltd. on the 26 May 2001.This paper endeavours to highlight the project objectives and backgrounds them against the difficulties experienced with respect to the site-specific conditions, the design complexities and risks associated with the contract, from a contractorÆs perspective.

Jan 1, 2002

By J. Kim, H. Cho

The objective of the experiment was to investigate the efficiency of hindered-settling column in recovering carbon from anthracite. Two types of Korean anthracites were prepared for feed materials. Each sample was crushed and classified by size, and washability analyses were performed. Separation efficiency was evaluated under various operating conditions using a laboratory scale hindered settling column. Results showed that the carbon recovery was higher for the smaller sizes, but the purity of the product was better for the larger sizes. In, overall, 2-0.21mm particles of 40-45 % ash could be processed into about 20 % ash products.

Jan 1, 2002

By G Hayes

Ore from the Browns deposit near Batchelor, in the Northern Territory of Australia, is a fine-grained polymetallic sulfide ore hosted in graphitic black shale. Minerals of economic significance are seigenite (Co,Ni)4S3, Galena (PbS) and Chalcopyrite (CuFeS2) with minor Sphalerite (ZnS). Gangue minerals include quartz, carbon and K-feldspar. The grain size is fine, with a significant amount of the seigenite present as Early flotation work determined that a grind size of around 20 microns was required to achieve clean sulfide concentrates. This work recommended oil agglomeration flotation, in which small sulfide minerals were collected, then loosely agglomerated with oil ahead of flotation into a heavily mineralised froth. In the 400 kg/hr prototype plant this froth proved unmanageable. A conventional flotation circuit after grinding to a P80 of 24 microns and using very low flotation pulp densities resulted in an 86 per cent cobalt recovery.The paper analyses further laboratory work which has increased cobalt recovery to 91 per cent by grinding to û250 microns ahead of flash flotation. The real cobalt recovery breakthrough comes from flash flotation of the whole mill discharge rather than the more usual flash flotation of cyclone underflow. Flash flotation tailings are ground to û38 microns and are floated under normal flotation conditions with only the scavenger concentrates being reground to 20 microns.A one tonne per hour prototyping campaign is scheduled to demonstrate the robustness of this circuit.

Jan 1, 2002

By J. Buckle

"Recognition of the diamond potential of the Wawa subprovince was initially determined from regional data using a kimberlite model. The world’s largest stable Precambrian craton, the Superior Province, is considered to be favourable for the emplacement of diamondiferous kimberlite. The Wawa area is located near the intersection of intra-craton structures visible in the regional magnetic data.The Enigma project is located north of the town of Wawa in northern Ontario. From field evidence and background research, it became obvious that in the Wawa area there were at least two potentially diamond-hosting events, Archean lamprophyric volcaniclastics and Proterozoic kimberlites. The host lamprophyric rock does not contain the classical KIM signatures. However, to complicate the Enigma, stream sediment samples within 200 m of the diamond-bearing lamprophyre produced a typical suite of kimberlite indicator minerals.The micro- and macro-diamond content of the Wawa lamprophyric volcaniclastic rocks is typically 0.2 ct/t to 1 ct/t, although it can be higher locally. The economic diamond potential of these Archean dykes, sills and irregular lamprophyre bodies is still under-explored (Kaminsky, 2002, unpubl.). Oasis Diamond Exploration is currently exploring the area using geophysical, geochemical, and geological data."

Jan 1, 2002

By Michael J. Brown

Load testing is important for controlling the quality of piled foundations. The Statnamic test is an alternative to existing testing methods with a load duration that lies between that for static and dynamic tests. Current methods of analysis offer excellent correlation between static and Statnamic tests for coarse-grained soils but often over-predict the capacity for fine-grained soils. Thus a calibration chamber is being used to produce instrumented beds of clay with reproducible properties. A model pile placed in the beds can be loaded at varying rates using a computer controlled servo-hydraulic system. Results from the modelling will be used to improve methods of analysis and govern the design of a full-scale study. Initial results suggest the rate effect can be represented by a power law relating pile velocity and resistance. Statnamic loading of the model pile produced large negative pore pressures in the clay bed.

Jan 1, 2002

By M. J. Lukhele

Paper written on project work carried out in partial fulfilment of B. Tech (Mining Engineering) degree A number of high wall mining methods were developed over the years to mine coal reserves exposed on the high walls created during surface mining. The auger mining system was initially developed in the early 1940s in the United States of America. High wall mining is a method of recovering coal from seam exposed either by mechanical excavation methods or natural erosions. This is usually associated with strip-mining (opencast) where the stripping ratio is high and uneconomical to mine using the opencast mining method. This paper discusses the surface auger mining as deployed at Rietspruit Mine Services Proprietary Limited.

Jan 1, 2002