Search Documents

By P Lever, D Hainsworth, H Gurgenci

The ACARP Landmark initiative has created the opportunity to advance the level of automation in the coal industry by first focusing on the core production area of longwall mining. A Landmark Longwall Automation project was commenced in July 2001. The major outcome of automation using on-face observation has been divided into ten outcome areas that have been fully scoped for a three-year initial project life. A major facilitating technology has been the implementation inertial navigation system (INS) technology that can map the shearer position in 3D. A focus of the project is to deliver a system that is at least as productive as the current most productive manually controlled longwall face.

Jan 1, 2002

By James J. Graham

Uravan, Ambrosia Lake, Gas Hills and South Texas are all historic names in US uranium. These mining areas supplied the uranium that brought the United States into the nuclear age during the 1960s, and fueled the birth of nuclear energy for peaceful uses — a promise of nearly limitless, clean energy for the world’s future. That promise still exists today, but it is hard to hear over the rhetoric of environmental activists and politicians. Nuclear power offers dependable electricity with limited environmental impact at stable prices. Nuclear power releases no greenhouse gases or particulate matter into the atmosphere. High level nuclear waste (HLW), although long lived, is readily controlled and compact. In the United States, generating 1 billion kWh of electricity with coal produces 47 kt (52,000 st) of solid waste (ash and sludge), compared to 3.6 t (4 st) of HLW produced by nuclear.

Jan 1, 2002

By A. McGarr

The shear stress t that can be sustained by the rock mass in the environs of a mining-induced earthquake controls the near-fault peak ground velocity v of that event according to v=0.25(ß/G)t, where ß is the shear wave speed and G is the modulus of rigidity. To estimate t at mining depths, I review the results of four studies involving Witwatersrand tremors that relate to the bulk shear strength. The first and most general analysis uses the common assumptions that the seismogenic crust is pervasively faulted, has hydrostatic pore pressure before mining, and an extensional stress state that is close to failure. Mining operations reduce the pore pressure to zero within the mine and redistribute the stresses such that, in localized regions, the state of stress is again at the point of failure. Laboratory friction experiments can be used to estimate t in the zero-pore-pressure regime. Second, model calculations of states of stress in the vicinity of mining at about 3 km depth indicated the shear stress available to cause faulting near the centre of a distribution of induced earthquakes. Third, laboratory experiments combined with microscopic analyses of fault gouge from the rupture zone of a mining-induced event provided an estimate of the average shear stress acting on the fault to cause this earthquake at a depth of 2 km. Fourth, moment tensors determined for mining-induced earthquakes usually show substantial implosive components, from which it is straightforward to estimate t. These four different analyses yield estimates of t that fall in the range 30to 61 MPa which implies that near-fault particle velocities could be as high as about 1.5 m/s. To the extent that the causative fault ruptures previously intact rock, both t and v, in localized regions, could be several times higher than 61 MPa and 1.5 m/s.

Jan 1, 2002

By Andrzej Tejchman

A method of improvement of a subsoil under bored pile base by injection is presented. The method employs a special chamber attached to the reinforcement at the bottom of the drilled borehole. The chamber is made of semi-permeable textile bag. The injection entered under high pressure into the bag, causes prestressing of subsoil under the pile base. The results of load tests of piles improved in this manner have shown a substantial increase of their capacity together with simultaneous reduction of settlements. This technology has been implemented for four constructions such as trestle bridges in Gdynia and Warszawa and the bridges in Szczecin and Gdansk. The injection effects are shown based on the load test results.

Jan 1, 2002

Although cyclones have been around in their current form since the early-1890s, there have been some exciting new developments, which have extended their efficiency/operation. These developments have taken place with both dense medium and classification cyclones. The more noteworthy developments are:Inlet designInlet design is the determining factor in classification cyclone capacity and efficiency. The recently developed ribbon inlet with patented pressure bulge has not only resulted in unbelievable increases in capacity, but also in efficiency. Sharpness of separation corresponding to an alpha value of greater than four has been achieved! Secondary offtakeOne of the factors leading to reduced cyclone efficiency is the presence of coarse particles in the cyclone overflow. The secondary offtake has been developed specifically to scavenge these particles from the cyclone overflow with great success. Water injectorThe other major factor resulting in reduced cyclone efficiency is the presence of misplaced fine particles in the cyclone underflow. The water injector, which has been around for many years in various forms, can reduce this short circuit fraction by up to 50 per cent. 3-in-1 cycloneThe 3-in-1 cyclone combines the inlet design, secondary off take and water injector into a single unit resulting in the most efficient classification cyclone available in the market. The RejectorTMIron ore has a high yield to underflow and traditional dense medium cyclones have always been spigot constrained. The Rejector TM is an exciting new development whereby the spigot capacity has been increased substantially. The application of the Rejector TM will result in fewer/smaller cyclones being required for a given duty resulting in efficiency gains and reductions in both operating and maintenance costs.

Jan 1, 2002

By Yves Breau, François Robichaud, Jacques McMullen, Pierre Pelletie

"The Expert System implemented at the East-Malartic mill controls a copper flotation circuit while taking into account the profitability of the operation. Treating a copper gold ore, the flow sheet integrates a flotation step followed by cyanide leach circuit. The Expert System calculates the actual net smelter revenue of the flotation circuit, accounts for the operating cost of the cyanidation circuit and defines optimal metallurgical operating targets to optimize the overall economics. To be realistic, probability factors and circuit diagnostic analysis are integrated in the operating target selection. The Expert System has proved to be successful, robust and flexible. It resulted in a copper concentrate grade increase of 1% while maintaining recovery. The use of the expert system also gives plant personnel good training procedures and promotes interaction with mill operator.INTRODUCTIONThe East-Malartic mill is located close to the town of Malartic in North Western Quebec, Canada. The mill was first commissioned in 1938. The flowsheet at that time was a straight cyanidation circuit. The original mill operated in that mode up to the discovery of the Bousquet 2 orebody in 1989 which consisted of a massive copper sulphide ore averaging 0.7% copper and 7 g/mt of gold. Bousquet 2 ore processing required a mill retrofit. Grinding capacity, gravity and copper flotation circuits were inserted prior to the cyanidation circuit in order to achieve 3,200 mtpd capacity at expected recoveries.In 1993, control of the flotation circuit was deemed critical in order to maintain the flotation performance and to reduce cyanide consumption since the copper sulphide contained in the Bousquet 2 ore is a high cyanide consumer (50% bornite). (McMullen, 1999) As a result, the implementation of advanced control strategies in order to increase the metallurgical profitability of the plant and to reduce the operating variability between operators was the most rational alternative. In 1994, Corem was chosen to perform the plant audit and to write the first set of rules. The on-line control strategy was started up in 1995. In 1996 and 1997 the Expert System was shutdown because of an extreme change in the ore coming from the milling of Bousquet #1 ore and the departure of the projects engineer. In 1998, the system was restarted and the results were impressive. Furthermore in May of 2001 a patent was issued for the control strategy. (Breau, 2001)"

Jan 1, 2002

By F P. Hao

Organo-sulphur-based collectors (eg xanthates, dithiocarbamates and dithiophosphates) are widely used in the flotation of sulphide minerals. Xanthates (ROC(=S)Sû), for example, adsorb strongly at sulphide mineral surfaces, in a reaction that is electrochemically coupled with the reduction of dissolved oxygen. One of the oxygen reduction products, hydrogen peroxide, reacts directly with dissolved xanthate, leading to its oxidative decomposition. Experimental work has been conducted, using ethyl xanthate, to understand the molecular mechanism by which hydrogen peroxide reacts with xanthates. A number of degradation products have been identified, some of which have not been reported previously. This oxidative decomposition reaction pathway is discussed in the broader context of xanthate decomposition in flotation systems. One of the identified ethyl xanthate decomposition products, ethyl perxanthate (ROC(=S)SOû), has been observed in the process water of a number of mineral processing operations. The interaction of this molecule with goethite (α-FeOOH) particles, typical of that found in tailings dams, has been studied in more detail using attenuated total reflectance (ATR)-FTIR. The ethyl perxanthate molecule has been found to coordinate to iron (FeIII) at the goethite surface, and undergo a surface-catalysed decomposition process. In the presence of both PbII and goethite, a ternary surface complex is formed, where ethyl perxanthate is coordinated directly to surface adsorbed PbII atoms. The results obtained give some insight into the environmental fate of ethyl xanthate in tailings streams, and a basis on which to consider the environmental importance of such species in tailings dams. Strategies for the destruction of residual xanthate levels in waste water streams are discussed in terms of the likely reaction products.

Jan 1, 2002

By J. W. Hawkins, K. B. C. Brady, K. Miller, J. Cuddeback

Remining of abandoned coal mines in Pennsylvania requires the implementation of pollution abatement and mining techniques called Best Management Practices (BMPs). Water-quality data from over 100 remining sites with more than 230 abandoned discharges were analyzed with respect to the types of BMPs employed to abate the pollution loadings of acidity, iron, manganese, aluminum and sulfate. Discharges exhibiting a significant decrease in acidity were most highly associated with sites where large volumes of alkaline materials were encountered (66.7%) or added (63.7%). The best results for iron loading were achieved with large-quantity alkaline addition (54.6%) and water handling systems (47.8%). Water handling systems (47.4%), daylighting (40.7%), and revegetation (40.2%) were associated with significantly lower manganese loadings. The decreases in acidity and sulfate loads associated with increasing the amount of alkaline material in the backfill indicates that the production of acid mine drainage can be retarded by adding large quantities of alkaline materials.

Jan 1, 2002

In the Ngakuru area, zeolite deposits occur in late Quaternary lake sediments and ignimbrites. The deposits are associated with sinters, hydrothermal eruption breccias, and quartz-adularia altered fault breccias: all indicators of a shallow epithermal environment. Several of the deposits are adjacent to epithermal gold prospects. Zeolites are most abundant in lacustrine tuffs of the Ngakuru Formation, a 100-300 m thick sequence of siltstone, tuff, diatomite, sandstone and conglomerate. The formation overlies the Ohakuri Ignimbrite dated at c. 270 Ka, and is unconformably overlain by alluvial sands and gravels which are younger than 20 Ka. Individual zeolite deposits contain 30-80 per cent zeolite over a thickness of up to 45 m in thinly stratified tuff beds. The tuff beds are locally overlain by diatomite. The tuffs are composed mainly of glass shards and pumice clasts, with minor volcanic plagioclase, quartz and biotite crystals. Glass shards in the tuffs are replaced by the silica-rich zeolites mordenite and clinoptilolite. Amorphous silica (opal A), opal-CT, K-feldspar and smectite are also present. The distribution of the Ngakuru Formation is controlled by northeast trending normal faults, which separate it into the Ngakuru and Guthrie grabens. A silicified (quartz-adularia altered) hydrothermal breccia along one of the fault zones suggests that the faults acted as feeders for heated water that caused the deposition of the zeolite minerals. Some of the zeolite deposits are adjacent to sinters and hydrothermal eruption breccias. The location of the sinter about 20 m above one deposit indicates that the zeolites were formed at a depth of 20 to 70 m below the paleosurface. The hydrothermal eruption breccias contain clasts of altered ignimbrite, which contain geochemically anomalous gold and silver values. By analogy with their occurrence in active geothermal systems in the Taupo Volcanic Zone, mordenite and clinoptilolite in the Ngakuru deposits probably formed at temperatures of 60-150oC from near-neutral pH waters as a result of interaction with glass-rich tuff beds. The Ngakuru zeolite deposits are therefore interpreted as shallow hydrothermal alteration zones within larger epithermal gold-bearing systems.

Jan 1, 2002

By B. Genc

After the explosion at Middelbult Colliery, South Africa in May1993, which claimed 53 lives, the South African Coal Mining Industry and the Safety In Mines Research Advisory Committee (SIMRAC) united forces to establish a surface facility to develop and test on-board flame suppression systems for continuous miners and roadheaders. The first test that was conducted in this newly constructed test tunnel at the Kloppersbos Research Facility, CSIR was in July 1995.Since then 70 tests have been conducted using the facility and have focused on on-board active ignition suppression systems for continuous miners (CM) and road heading (RH) machines to enhance the safety of South African mine workers in collieries. These suppression systems are mounted on the CM or RH machine and detect the occurrence of an ignition by means of light-sensitive sensors. The electronic signal from the sensor triggers the suppression system, creating a flame-suppression curtain, containing and extinguishing the flame in the immediate vicinity of the ignition. Forty-three tests have been conducted with an active on-board suppression system present inside the test tunnel. Since flame propagation speed is an extremely important parameter, the CSIR-Miningtek made the results of the test programme available for re-analysis. Flame speed depended on whether a machine was present in the heading or not, the geometry of the heading and the volume and composition of the explosive mixture of gas. Flame speeds of up to 190 m/s were recorded. However, the active suppression systems were almost always successful in containing flame propagation.

Jan 1, 2002

By T. H. Eyde

Worldwide production of natural zeolites during 2001 was estimated to be about 3.5 Mt (3.85million st). Construction and agriculture continued to be the major consumers. Estimated production in North America during 2001, including the United States, Canada and Mexico, was about 40 kt (44,000 st). In the United States and Canada, the zeolitic tuffs are ground, extruded or modified for use as adsorbents, desiccants, ion-exchange media and carriers. In Mexico and the rest of the world, the zeolitic tuffs are cut into dimension stone that is used in construction. Zeolitic tuffs are usually composed of the minerals clinoptilolite, mordenite or both. They occur in a variety of colors and are easy to cut and shape. And they have low thermal conductivity. This construction application is classified with dimension stone rather than with chemical and agricultural uses.

Jan 1, 2002

By P M. Ashley

Antimony (Sb) is an element similar to arsenic that forms anions in surface waters, rather than cations like other metals. Little is known about natural mobility of antimony in the environment. However, recent studies have suggested that antimony has similar toxicity to arsenic. Current New Zealand drinking water guideline values are 3 parts per billion (0.003 mg/l) for antimony and 10 ppb (0.01 mg/l) for arsenic. Antimony occurs principally in stibnite (Sb2S3) in mesothermal vein deposits hosted in low grade metamorphic belts of eastern Australia and southern New Zealand. Many deposits have been mined historically, including one large deposit, at Hillgrove, NSW. Oxidation of stibnite and associated arsenopyrite and pyrite causes local acidification of natural waters but acid is readily neutralised by carbonates in mineralised zones and host rocks, and therefore waters are near-neutral (pH 6-8.5). Antimony dissolves readily in moderately oxidized, near-neutral waters. Experimental stibnite oxidation yielded up to 37 mg/kg (37 000 ppb) dissolved antimony, and mine and tailings dam waters at Hillgrove mine have up to 55 mg/kg (55 000 ppb) dissolved antimony. Natural stibnite can contain >5000 mg/kg arsenic in solid solution and therefore dissolution of stibnite, arsenopyrite and arsenian pyrite also releases arsenic into waters. Resultant dissolved arsenic concentrations are up to 3.6 mg/l (experimental) and up to 7.2 mg/l (mine and tailings dam seepages). Mine and tailings discharge waters have elevated antimony and arsenic where they emerge, but attenuation occurs by deposition of the metals on to amorphous iron oxyhydroxides which can contain >10% each of antimony and arsenic. Historic disposal of mineralised waste rock and tailings into the stream system at Hillgrove has caused contamination of sediments and waters with antimony and arsenic for at least 20 km downstream with effects traceable in sediments for 300 km. Other stibnite-bearing deposits are likely to have analogous environmental effects, particularly from historically-mined sites.

Jan 1, 2002

By David Siskind

The authors studied small seismic exploration blasts for vibration characteristics and effects on structures in Mexico. Obtained were 267 three-component recordings of ground vibrations and structure responses from 62 test blasts at six single-story masonry structures. Charges were 4.55 kg (10 lb) of Vibrogel expolsive at depths of 20 and 30 meters. Initial blasts were 240 meters distant and proceeded towards the structures to as close as 5 meters. All blasts were in soil media in two basic types of terrain, low saturated areas and upland dry areas. Structural inspections were before, during, and after the test blasts.

Jan 1, 2002

By Howard Roscoe

Linking Ashford International Station to the new Channel Tunnel Rail Link required over 5000 rotary bored and CFA (continuous flight auger) piles to form tunnel walls and viaduct foundations and to support overbridges and trackside barriers.. Much of the work was carried out close to the existing railway infrastructure. Plunged columns were used to maintain traffic flows over the tunnel site during construction. The results of an extensive programme of vertical and lateral load tests on bored and CFA piles in heavily overconsolidated Weald Clay are compared to illustrate the relative importance of stress relief and of prolonged exposure to bentonite. The completion on schedule of this major piling and ground engineering contract (value £30 million) demonstrates that collaborative working in partnership produced cost effective solutions to a series of challenging technical and logistical problems.

Jan 1, 2002

By W Herrmann, R R. Large

Volcanic-hosted massive sulfide (VHMS) deposits in ancient, submarine volcanic belts of Australia include mound, lens and sheet-style Zn-rich polymetallic deposits, massive and disseminated pyritic Cu-Au deposits and disseminated, stratabound Au-only deposits. Variation in morphologies, metal ratios, volcanic environments and alteration features indicates there exists a spectrum of deposits from the classic VHMS model, to hybrids between VHMS-porphyry Cu and VHMS-epithermal end members. Zn-rich, polymetallic deposits form eitheron, or just below, the seafloor, whereas the Cu-Au and Au-only deposits form sub-seafloor by replacement of specific volcanic lithologies. Alteration zoned outwards from quartz -> chlorite -> sericite ¦ carbonate is typical of VHMS deposits across the spectrum. Quartz and carbonate alteration is dominant in the Au-only systems,chlorite alteration is commonly developed close to Cu-rich ores, and sericite and carbonate alteration zones are well developed in the stratiform Zn-rich ores. The most useful geochemical vectors for Zn-rich ores are the alteration index [AI=100(MgO + K2O)/(MgO + K2O + CaO + Na2O)], the chlorite-carbonate-pyrite index [CCPI=100(MgO + FeO)/(MgO + FeO + K2O + Na2O)], Mn content of carbonate, Mg/(Mg+Fe) ratio of chlorite,whole-rock Tl, Sb and Ba/Sr ratio, S34S of pyrite, and whole-rock S18O. The most useful vectors for pyritic Cu-Au ores are AI, CCPI, S/Na2O ratio, Na content of white mica, and Fe content of carbonate.

Jan 1, 2002

By Grant R. J. Bearss

Due to environmental concerns in urban construction, many typically simple projects become very complex or feasibly impossible. The introduction of relatively new concepts has redefined "impossible", again simplifying these projects and making them "possible". Case Study One covers the use of Pressed-in Tubular Piles on portions of the Long Island Expressway in Queens, New York. Innovations in the design, material and installation method solved many typically inherent problems on projects of this type and resulted in cantilevered walls that supported a 35ft (10.668m) excavation. Design predictions and actual measured deflections of this wall were within millimeters. Case Study Two covers the use of Pressed-in Tubular Piles on portions of the Hodogaya Bypass in Yokohama, Japan. Innovations in equipment development allowed for a cantilevered retaining wall to be constructed without affecting the adjacent right-of-way, dramatic reduction of the overall construction duration and installation of tubular piles in soils with SPT N values greater than 160.

Jan 1, 2002

By Michael Peterson, Robert Davinroy, Robert Rapp, Gregory Hempen, David Herzog, Thomas Keevin

Fish sampling in a deep-water, high velocity, environment is extremely difficult. Conventional techniques such as electro-fishing and netting have been limited to depths generally less than 7 meters (m) and velocities below 1 meter per second (mps). The goal of our study was to sample a bendway weir field on the Mississippi River to assess the effects of the weir field on the fishery. In a bendway weir field, depths can exceed 20 m, and velocities can exceed 3 mps, making conventional sampling techniques inefficient.

Jan 1, 2002

By D Syme

In the middle of 2000, BHP Billiton implemented a Six Sigma Plus business improvement program known as Operating Excellence. It was developed based on a business bottom line initiative to deliver 35 - 40c/share and was one of the BHP Billiton strategies to deliver $2 earnings per share and a longer term $40 share price (BHP share price). Cannington is a silver, lead and zinc mine owned and operated by BHP Billiton. Through implementing Six Sigma Plus Cannington wanted to:have in-house capabilities to change and improve; tailor for the needs of each business unit and department; have æSharing of its KnowledgeÆ as a tool for improvement and have a competitive edge across Cannington û to be better than our competitors; learn from and leverage off the successes of improved safety and prior business improvement efforts; and ensure networking and sharing of information have common measurement systems across all assets. As with most business improvement programs û Six Sigma Plus was met with some degree of skepticism, especially given the amount of resources involved. After 18 months, much of this skepticism has been replaced with enthusiasm as peopleÆs understanding and acceptance of its fundamental concepts are being realised. The idea behind Six Sigma Plus is that it combines sound technical solutions with high acceptance by those who need to work with or implement the change. The future vision for Six Sigma Plus is that it become part of what we do at Cannington û just like safety and environment û so that Six Sigma tools and methodologies are used in our every day work.

Jan 1, 2002

By Robert F. Randolph, Jeffery L. Kohler, David C. Byrne

Multiple versions of an educational message can reach a diverse population more effectively than a single version. For instance, some workers are trained in formal classrooms while others are self-taught. The National Institute for Occupational Safety and Health has developed multiple versions of a hearing loss simulator (an interactive software package, a Web-based module, and an electronic slide show) to show how a single set of information can be readily adapted to different delivery methods. The three versions of the simulator were developed with a minimum of effort and expense compared to a single, less-flexible version. The interactive software is best for training sessions led by a hearing conservation professional, the Web pages are best suited for an individual worker, and the slide show is best for a small, more-generalized, training class. This paper will describe additional advantages and disadvantages of different delivery systems and will show what considerations are helpful in designing content that can be readily adapted to alternate presentations.

Jan 1, 2002

By I Lumsdaine

QNI Pty Ltd operates the Yabulu Refinery located 25 kilometres north of Townsville, North Queensland. The plant treats nickel laterite ores sourced from the Philippines, Indonesia and New Caledonia. The cobalt head grade and overall recovery expectations for the 2001/2002 financial year are 0.161 per cent and 53.8 per cent respectively. Cobalt is a valuable byproduct derived from the nickel refining operation which utilises the Caron Process. Any increases in cobalt recovery that are achieved from the existing relatively low level provide significant improvements to the bottom line of the operation. Towards the end of 2000, a project was undertaken to characterise cobalt losses with the sole purpose of improving cobalt recoveries using a variety of analysis techniques. The Time-of- Flight Secondary Ion Mass Spectrometry (TOF-SIMS û University of South Australia) method was used to verify the presence of surface bearing cobalt species, originating from either co-precipitation or adsorption mechanisms. Cross-section examinations were also performed using Scanning Electron Micrscopy (SEM) and Energy Dispersive X-ray Spectrometry (EDXS). These techniques indicated the presence of high cobalt concentrations (in the order of several per cent) within a select number of roasted and leached ore particles. The phenomenon of cobalt losses due to incomplete leaching within specific ore particles was not widely documented within the Refinery prior to these studies. In order to quantify losses via this mechanism, Mineral Liberation Analysis (MLA û JKTech Centre) was also performed on key samples. This paper serves to document a systematic approach in determining the source of significant valuable mineral losses in an established, operating plant. It discusses the use of a variety of analytical techniques, which have been adapted for the minerals processing industry, but are strongly relevant for plant investigations in the hydrometallurgical industry.

Jan 1, 2002