Search Documents

By R. Bruce Patterson

The New Tacoma Narrows Bridge is a classic suspension bridge founded on concrete caissons. Caisson construction was complicated by the proximity of the existing bridge piers, only sixty feet away. High capacity plate anchors were used successfully to moor the new caissons in currents as strong as seven knots during construction.

Jan 1, 2004

By M. Sanchez, I. Imris, G. Achurra

The Smelting and Converting El Teniente Process for copper concentrates as well as Slag Cleaning Furnace Technologies to treat slags coming out from the El Teniente Furnaces are widely applied today in Chile and around the world. Several industrial applications of this process have shown their capability to treat copper concentrates in a wide range of chemical and mineralogical compositions. Main operational parameters determining performance of the process are: oxygen enriched air flow rate, degree of oxygen enrichment, moisture content of the solid materials processed, molten material levels inside the vessel, frequency of molten materials tapping, bath temperature and copper losses in slags. In this work, the copper losses in the slags from El Teniente pyrometallurgical process are predicted by calculation from thermodynamic data and compared with those determined by microscopic examination and slag industrial data. Results obtained show that the main part of copper losses in the slag from El Teniente Furnace are mechanically entrapped or floated unsettled droplets of the coexisting matte phase. by the contrary the very low copper losses in the slag from slag cleaning furnace are limited by the physico-chemical form.

Jan 1, 2004

By V. Brabie, S. Jansson, L. Bohlin

The rate of dissolution of solid MgO-C and doloma into liquid in CaO-Al2O3-SiO2-MgO slag at different temperatures was studied under conditions of forced convection by rotating cylindrical refractory specimens in a stationary crucible containing the molten slag. The corrosion rate was calculated from the change in diameter of the cylindrical specimens. Refractory specimens were 13 mm in diameter and 70 mm long. The specimens were rotated for15 to 120 minutes at speeds of 100 to 400 rpm in the molten slag. The rate of corrosion increased with temperature and with the rotating speed of the rod, and decreased when the slag was nearly saturated with MgO. The experimental results confirm the assumption that the diffusion of magnesium oxide through the slag phase boundary layer controls the corrosion process. The corrosion mechanism seems to be the dissolution of the refractory materials into the slag, followed by penetration of pores and grain boundaries and dispersion of the grains in the slag. Keywords: MgO-C refractory, doloma refractory, molten slag, corrosion rate, corrosion mechanism

Jan 1, 2004

By J. Kunze, R. Degal

During the last 100 years, the submerged arc furnace has been one of the most amazing diversified melting units. These furnaces have found their application in more than 20 different main industrial areas such as iron, ferro alloy, chemical industry, lead, zinc, copper, refractory, titanium oxide, recycling, phosphorus etc. Such an evolution was only possible because of tremendous efforts in research and development and due to the large range of design solutions. The worldwide strong competition also forced the industry and plant suppliers to develop highly efficient, economically balanced units in optimized sizes and with long lifetimes, to adapt to the market conditions. Regarding the environment, the plants improved significantly in terms of water treatment plants and off-gas treatments as well as on site recycling units. This paper will give a short overview regarding the history of the furnace and the latest developments in today?s main application fields: ferro alloys, non-ferrous, special application and recycling. In addition new activities in research and developments are briefly discussed.

Jan 1, 2004

By Robin J. Batterham

We still need to innovate, but it is getting harder. The real price of metals is declining, return on shareholder value is lower than other industries, and there is a shorter-term focus on staying viable in a capital-intensive industry where timeframes for implementation of new technologies can be long (+I5 years). In this environment, the levels of R&D spent by major minerals companies are remaining steady at around 0.2%-0.5% of revenue. This is not large and to remain viable in the future, we need to be smarter about the way in which we do R&D. The mining industry is a knowledge-based industry. Driving down the cost curve demands innovation, which demands knowledge. To be smarter and more effective in our approach to innovation, a new paradigm is required Generating, capturing and using knowledge has evolved from Mode 1 (discipline based and clear distinction between basic and applied research) to Mode 2 (multidisciplinary, team-based approached with flow between basic and applied activities). Mode 2 is now seen to be much more efficient and to deliver better appropriability (Tegart 2003). To survive, we need to innovate, and the best way to do this is collaboratively. Some examples and pointers for the future will be given in this paper. THE CURRENT SITUATION The Rand report and other recent studies have painted a grim outlook for the mining industry. The real price of metals continues to decline (Figure 1) and profit margins remain thin. This is reflected in shareholder returnwhich are well below other industries (Figure 2)-and current management strategies-which reflect something of a "survival mode." The current focus for most mining companies is on short-term, incremental gains

Jan 1, 2004

By David A. Staab

Numerical modeling was used to investigate the feasibility of using two geophysical imaging techniques, cross-borehole ground penetrating radar (XBGPR) tomography and electrical resistivity (ER) tomography, for detecting and characterizing defects in deep-mixed soil columns. XBGPR modeling was accomplished with a three-dimensional numerical forward modeling code and a two-dimensional inversion routine. Spatial variations in apparent dielectric constant (Ka) and attenuation (a) were mapped. Electrical resistivity modeling was accomplished with a three-dimensional numerical forward modeling code and a three-dimensional inversion routine. Spatial changes in electrical resistivity were then mapped. Three different types of defects were simulated, in addition to a defect-free column. The computer simulations suggest that XBGPR tomography and ER tomography might be useful, non-destructive methods for detecting and estimating the extent of defects in deep-mixed soil columns. The results show that small, isolated defects might be difficult to detect, but defects approximately equal to or larger than the sampling interval (for XBGPR) or vertical electrode spacing (for ERT) should be detectable.

Jan 1, 2004

By H. Krogerus, P. Niemelä, P. Oikarinen

High carbon ferrochromium is produced by carbon reduction. No replacement for carbon as reductant has yet been developed. The reduction creates a considerable amount of CO-gas. In open and semi-closed furnaces the gas is burned when leaving the burden. In closed furnaces the formed gas is sucked out by a fan, washed and utilised as fuel. The formation of carbon monoxide is presented briefly starting from thermodynamic considerations up to solid and liquid state reduction. The volume, composition and energy content of the furnace gas are discussed, focusing on the raw materials and pre-treatment processes of the furnace feed as well as on the process equipment and control. Outokumpu has been using closed and sealed furnaces and utilising the CO-gas in its Tornio Ferrochrome Works since 1968. Today in Tornio with an annual ferrochromium production of 260 000 t CO-gas production is 186 million m3, representing 68 MWh an hour. At the same time the furnace power input is 95MW. About 98 % of the CO-gas is utilised, whereof 30% in the ferrochrome production itself. This paper focuses on the characteristics and utilisation of CO-gas. CO-gas is secondary energy, which on one hand saves primary electric and fossil fuel energy in ferrochromium production and, on the other, replaces other fossil fuels at the adjacent steel works. The characteristics of the fuel, requirements for utilisation as well as health and safety aspects are discussed. Utilisation of the gas has a high impact on the total dust and gaseous emissions and on the energy optimisation at the ferrochromium and steel works.

Jan 1, 2004

Council for 2003/2004 President T.R. Stacey President-elect F. M. G. Egerton Vice-presidents Senior W. H. van Niekerk Junior R.P.H. Willis Immediate Past-president S.J. Ramokgopa Honorary Treasurer J.A. Cruise

Jan 1, 2004

By S. A. Scott

Mintek developed the MinataurTM leach-solvent extraction-precipitation technology as a cost effective, easily operated alternative to conventional gold refining processes. The technology was first commercialized at the Harmony Gold Refinery in 1997 to produce 99.99 per cent gold product and has subsequently led to development of various value-addition steps including the casting of various investment bars, gold wire drawing and gold potassium cyanide powder production. In addition to refining gold to high purity, if an appreciable amount of silver is present in the feed material it is also refined to 99.99 per cent purity. The major advantage that the Minataur? technology has over other gold refining processes is the relatively low gold lock-up and reduced operating costs. The operating cost1as at April 2001 for the expanded Harmony refinery (24-ton per annum gold production) was approximately half that of conventional smelting and toll refining. The extractant employed for solvent extraction is relatively cheap and highly selective for gold, making the technology attractive in situations where significant quantities of platinum group metals or base metals are present.

Jan 1, 2004

By J. S. Harington

Our purpose is to record and to explain the widely changing numbers of the huge total of black workers on the gold mines of South Africa over the century from 1896 to 1996. These men were recruited from up to twenty territories, and their contributions are examined. The major areas providing labour over this long period have been Lesotho, the former Transkei within South Africa and Mozambique. From 1989 to 1996, for instance, these three areas accounted for over sixty per cent of the total labour force (tlf). Our principal Figure 1 shows the tlf fluctuating through time to reach a peak of 480 000 in 1988. Irregular falls are also documented with the most serious in 1995 to 180 000. Based on this graph we consider the political, economic, sociological and historical reasons behind these changing employment opportunities. These have included external world-scale events such as war or depression, as well as internal changes of national economy and policy. We show the importance for numbers employed of the discovery of gold in the Orange Free State in 1946, the influence generally of the ?Winds of Change? and the firm maintenance by the State of law and order. Varying gold production costs and profitability against high tax rates, allied with increasing wages and a lack of development capital, have led in the last decade to employment falling by fifty per cent, despite an actually higher value of gold output. Finally, this analysis considers the role of the migrant labour system as it affects, and is affected by, conditions in the gold mining industry, with special reference to its less than humane consequences in the numerically dominant territories of Lesotho and Transkei.

Jan 1, 2004

By K. Galovich, P. Krivokuca

"Quinsam coal mine is located about 25 km west of Campbell River on the east coast of Vancouver Island, British Columbia. Using continuous miners in a fully mechanized retreat room-and-pillar operation, it produces low sulphur, “super compliance” thermal coal for domestic and international markets at a rate of about 2600 t/d. Currently, 65 people work at the site, including some corporate employees.Opened in 1993, the Quinsam mine had a dismal safety record until 1997. Lost time injuries and medical aids were unacceptably high. In 1998, a change in corporate structure brought a change in safety attitudes; a total and unequivocal commitment to safety as job No.1 by corporate and site management. This commitment was clearly spelled out in a new mission statement, circulated to all employees by the new President and CEO, David Slater: “Safety is job No. 1; Production flows from safety; and Think safety at all times.” As well as re-defining workplace safety practices, QCC tightened engineering controls and enforced strict adherence to mine plans.This paper provides a general background to the mining operation, and describes the safety practices that have resulted in an enviable safety record in recent years, reflected by provincial and national recognition."

Jan 1, 2004

By Narong Thasnanipan

In Bangkok due to the prevailing condition of subsoil (existence of considerably weak stratum at top part) deep-seated large diameter bored piles of over 50 m depth with 0.8 -1.8m in diameter have been mainly used for heavy structures such as high rise buildings, elevated expressways, flyovers and more recently for underground subway stations of the first Bangkok MRTA system. As a part of pre-planned quality assurance regime and retrospective investigation, integrity of the piles are tested to obtain the information with regard to the potential deficiencies of the constructed piles which may have formed during pile construction process or may have been attributed by other activities after construction of the piles. An overview of three commonly used non-destructive tests such as sonic integrity, sonic logging and high strain dynamic load tests on deep-seated piles in Bangkok subsoil is presented in this paper. Advantages and limitations of each integrity test are discussed.

Jan 1, 2004

By G. C. Smith

Process control applications in the minerals processing industry have grown extensively over the years due to the many benefits derived, both financially and operation-wise. Although control theory is widely known, conventional control does not address many of the problems posed by minerals processing circuits. Some of these problems include interactions between process units, large dead times, few and sometimes unreliable measurements of process variables, non-linear systems, disturbances entering the process, processes with varying dynamics, and many more. For the past 26 years Mintek has been active in the field of providing specific, customized solutions for the minerals processing industry. This paper focuses specifically on applications in milling and flotation control. The underlying control principles have been applied to a wide range of other processes including submerged arc furnaces. Advanced control application is implemented on a common advanced control platform, called the PlantStar. Much innovation has been brought to the fore in terms of adapting theoretical techniques and developing new methods to resolve specific milling and flotation circuit issues by using process control. The general approach adopted by Mintek when implementing advanced control is to enforce stabilization of the process as a solid foundation for optimization strategies to be built upon. In doing this, a robust control solution is presented, and the end result is flow and level stability, better product quality regulation, increase in throughput and a stable feed to downstream processes. The MillStar advanced milling control system ensures that the milling circuit is at all times easy to operate while achieving optimum product quality and throughput. Stabilization should include product size regulation and sump level control. Another important aspect of stabilization control is the handling of milling circuit constraints without introducing cyclical behaviour and with minimal disturbance to the final product quality. Process constraints may include factors such as process water limitations, cyclone feed density, and cyclone underflow angle. An optimization strategy should be developed to increase the mill throughput without affecting product quality or introducing mill overloads. The relationship between solids feed and power draw is examined and manipulated for optimization. The interactive nature of flotation circuits and the presence of recirculating streams tend to make satisfactory control almost impossible with conventional techniques such as PI (Proportional plus Integral) or PID (Proportional, Integral and Derivative) control. The FloatStar Level Stabilizer simultaneously considers all the flotation levels in a circuit by use of a multivariable algorithm, and takes compensating action in anticipation of disturbances. The FloatStar Flow Optimizer is an optimization strategy that controls the concentrate flow rate between various sections of a flotation circuit (e.g. Rougher ?Cleaner; Cleaner ?Recleaner). By controlling the concentrate flow between the sections, the mass pull, circulating loads and residence times of the circuit can be stabilized, thereby enhancing the performance of the flotation process. Optimizing grade and recovery are coupled with the dynamic optimization of circulating flows. The FloatStar Grade-Recovery Optimizer will maximize the grade in a section, whilst ensuring that recovery or any other process specific limits remain within predefined limits. With successful applications on several milling and flotation plants worldwide processing amongst others PGMs, gold, copper and nickel, Mintek has shown that it is a leader in milling and flotation control innovation

Jan 1, 2004

By T Preston

Solid Energy is the largest coal producing company in New Zealand, employing 500 people and more than 250 mining contract personnel. The coal produced by Solid Energy plays a significant part in the energy mix for New Zealand being supplied to the coal-fired power station at Huntly. It is also supplied to a wide range of industrial users, NZ Steel, and primary processing. It is fair to say however that the positive economic and social benefits of coal have to some extent been overshadowed by the negative environmental consequences of coal mining.   Over the past two years Solid Energy have been actively researching and addressing the impacts that they currently have on the environment and making a significant investment in environmental improvements, rehabilitation projects and environmental research to address historical and ongoing environmental issues. These investments have been driven by the companyÆs commitment to its environmental policy, which states:   æSolid EnergyÆs overall environmental objective is for the cumulative result of all the activities we undertake to have a positive net effect on the New Zealand environmentÆ.   With such significant investment it is essential that the company is able to target expenditure wisely, ie invest where there is greatest environmental gain to be had, and are also able to actively demonstrate to stakeholders the improvements that are achieved. In order to be able to demonstrate the commitment and the steps that the company is making towards this goal a number of systems have been developed. Firstly an environmental management system along the lines of ISO14001 formalising the environmental processes, responsibilities, auditing and management review. Secondly as part of the planning element of the EMS an environmental management matrix, which allows the scoring of sites against environmental management goals, has been developed. Thirdly the monitoring and measuring tools have been upgraded with GIS driven relational databases installed for management of consent related information and monitoring results.   The development of the environmental management matrix has drawn on a number of existing systems such as the Australian Institute of Mining and Minerals Code 2000. In addition to adapting the scoring regimes from these methods the Solid Energy Environmental Matrix has been further developed to ensure that it reflects the actual environmental impacts on site, as well as the management and audit systems that are in place to control them at a strategic level. The development of this matrix has included a number of steps: +        reviewing the information that stakeholders would be interested in, +        reviewing what was already available, +        development of systems to collect data and benchmark the current         operations, and +        setting up support systems to ensure that the correct information would be provided for scoring.

Jan 1, 2004

By M. D. Dolan

In this study, the development of a new method for investigating the diffusion of metal cations in multi-component slag systems, using microprobe analysis is discussed. This method allows the analysis of the diffusion of multiple species within a single system. This project has focused on the diffusion characteristics of manganese, iron, calcium and silicon in silicate slags, in order to simulate industrial steel and ferromanganese production. The diffusion behaviour of transition metals is of particular interest because of the effects of their variable valence. This study identified the variation in diffusivity of slag components with changes in composition and temperature of multi-component slag systems. The molecular structure of the experimental calcium-aluminosilicate slags was investigated to determine the chemical and physical properties that influence diffusion behaviour. This experimental data was used to develop predictive models for diffusivity. These models enable the estimation of the diffusivity of many slag components in complex slags, over a range of compositions.

Jan 1, 2004

By Tom Treleaven, Andrew Williams

The town of Greenwich, CT, an exclusive suburb of New York City awarded several contracts for the installation of sanitary sewer in the North Mianus section of town. The Valley Road section was the most challenging from a rock excavation standpoint. The cut was up to 14 ft (4.25m), with adjacent utilities [20 in. (500mm) water, 6 in. (150mm) water and 8 in. (200mm) gas] located to within 5 ft. (1.5m) of the proposed sewer trench. Rock types varied but were ultra metamorphic in nature, ranging from quartzites, granite gneiss and various types of migmatities.

Jan 1, 2004

By Donald Bruce

The three types of specifications which are used for micropile work are: ? Performance Specifications: The contractor is permitted control over certain design and/or construction procedures but must demonstrate to the owner through testing and/or certification that the final product meets the specified performance criteria. This method allows and encourages the contractor to provide a competitive and/or innovative micropile design within the framework of the overall design requirements. The responsibilities for the work are shared between the owner and the contractor. ? Open Specifications: These leave the scope and design of the installation up to the micropile contractor. This method is the most common for securing bids on temporary micropile work. The responsibility for design and performance is clearly placed on the contractor. Open specifications are not recommended for permanent applications. This method allows the contractor to select the most economical micropile system. ? Prescriptive Specification: The Owner describes specific procedures that must be followed, but which may not necessarily describe the objective of the work. When prescriptive specifications are used, the owner is responsible for the proper performance of the system. The contractor is responsible for satisfying the details of the specifications. Performance specifications are the most common and best reflect the challenges and interests of micropile technology and applications.

Jan 1, 2004

By T. Tamura

It is known that the CaO-FetO-P2O5slag system has a wide liquid miscibility gap at steelmaking temperatures and this two-liquid slag phase has many advantages such as high activities of both FetO and CaO and high amount of P2O5. The phosphorus distribution ratio between the two-liquid slag and molten steel was confirmed to be higher than that between CaOsat.-FetO-P2O5slag and molten steel. The two-liquid slag may be useful for dephosphorization of molten steel and reduction of slag volume. Furthermore, the phase equilibrium of two-liquid CaO-FetO-P2O5slagsaturated with MgO was measured to determine the applicability of the two-liquid slag to dephosphorization in steelmaking process. Keywords: slag, refractories, solid solution, two-liquid phase, dephosphorization, steelmaking, phase equilibrium.

Jan 1, 2004

By J. S. Stachulak, K. A. Mackinnon

This paper deals with specifying and evaluating fans for mine ventilation projects. Topics such as fan and equipment design life, operating points, and operating conditions are discussed. Common operating problems, such as vibration, parallel operation, mechanical failure, erosion, corrosion, and deficient fan performance are covered. Apart from identifying the potential operating problems, likely causes and suggested remedies are given. Fan type, fan accessories, and likely system effects and fan testing are discussed. Suggestions on what should be covered when evaluating different fan options and proposals and suggestions on the verification of supplier claims and guarantees, including cost of operation, the evaluation of initial capital cost, estimate on maintenance costs, and likely replacement expenditure over the life of the fans. In addition, fan reliability, operational flexibility, suggested construction details and fan vendor past history and experience are reviewed.

Jan 1, 2004

By F. Bonnet, J. Lehmann, H. Gaye

A review of thermodynamic information and models of slags, including associated software when available, is presented. The pertinence and accuracy of these models is discussed by comparison of their predictions for various slag thermodynamic properties with the available experimental data. Practical industrial applications will be illustrated by a literature review of the dephosphorization process of ferromanganese alloys and by the description of Ti behavior during silico-manganese alloys production. This latter example will show how the thermodynamic models have been used to propose a flotation treatment at low temperature to enhance TiC removal.

Jan 1, 2004